Used Moisture for sale (251)

Condition: as good as new (ex-display), Year of construction: 2024, Primary crusher Basic machine starting from € 29,950 net *Options against surcharge Ideal for pre-crushing bulky materials such as pallets, boards, beams, fruit crates, polystyrene, plastics and much more. For the production of wood chips, the primary crusher can also be installed directly above a single-shaft shredder Machine in pre-production * Special options available at extra cost Your advantages: + Volume reduction of up to 70 + Significantly lower transportation costs + Low disposal costs + Production of fuel material + Also ideal upstream of a single-shaft shredder for the production of wood chips Weight: 1,200 kg Dimensions 2050x850x1600 mm Cutting unit opening 1300x700 mm *Optionally also available in 1600x700 mm (motor then 11 kW) (surcharge + 4.995 € net) Throughput: up to 50 pallets/pieces per hour *depending on material Motor: 7.5 kW Options: Industrial top hopper (closed on 3 sides) + € 4,950 net Extra emergency / off button + 495 € net 200 mm extension + 497 € net Requirements for the raw material: - Moisture content less than 30 % ATRO - The machine must be installed in accordance with CE guidelines or secured on site against access from below (into the cutting unit) Cajdpfx Ajfd Icieddsa - Pallets up to a dimension of 1200x800 mm can be processed Longer parts also work on edge

Condition: used, Year of construction: 2019, operating hours: 4,000 h, functionality: fully functional, machine/vehicle number: BP 500 A, DESCRIPTION BRIQUETTING PRESS This press is intended for compressing secondary raw materials into briquettes (briquette shape: rectangular). Technical specifications of the press: Dimensions: Length: 1800 mm (2100 mm for transport) Width: 1800 mm (2000 mm for transport) Height: 1900 mm (2200 mm for transport) Net weight: 2945 kg Power supply: 380 V, 50 Hz, 33 kW, 70-100 A Output capacity: 450 kg/h (+/-50 kg depending on raw material type and fraction) Noise level: A-weighted sound pressure level at operator’s station: 77.8 dB +/-5 dB Compression pressure: Minimum: 1000 kg/cm² Maximum: 1700 kg/cm² Pressure: Max. 300 bar Caodpexmav Nofx Addsa Raw material moisture content: No more than 14% Briquette dimensions: Width: 150 mm Thickness: 60 mm Length: 40-105 mm Permissible ambient temperature for operation: -20°C to +35°C (up to +50°C with additional cooling system) The press consists of: Electrical system – controls the hydraulic press system. There are four electric motors: the first (30 kW) drives the main hydraulic pumps, the second (1.1 kW) powers the cooling hydraulic pump, the third (0.55 kW) drives the cooling fan of the oil system, and the fourth (1.5 kW) drives the sawdust feed screw. The operation of the motors and hydraulic valves is managed via contactors and intermediate solid-state relays by a microprocessor with expansion modules. For visualization and parameter adjustment, a liquid crystal display with buttons is provided. Hydraulic system – manages the operation of hydraulic cylinders using pumps, high- and low-pressure valves, solenoid valves, and hoses. There are three hydraulic cylinders: the first is the main cylinder for compressing sawdust, the second is a vertical cylinder for initial sawdust compaction, and the third is a forming cylinder for moving the briquette form. Also installed are an oil cooling system with a pump and air cooler. Oil filtration is performed by the main high-capacity filter, a filter for the cooling system, and a fine filtering unit. Feeding of raw material into the press is performed by an integrated loading hopper. The raw material in the hopper is mixed intermittently to prevent bridging. The mixer is driven by a chain from the auger gearmotor. The auger cyclically feeds the material to the shaft of the vertical cylinder. The hopper is equipped with two level sensors – lower and upper. When the hopper is enlarged, the sensors can be repositioned as needed. Control – dual-mode, manual and automatic, is provided. All control equipment is mounted in the electrical cabinet. Automatic control constitutes the normal press operation without operator intervention. Manual control is used for press setup, troubleshooting, returning the cylinders to their home positions, or in emergency situations. Operation is facilitated by a display located on the cabinet door. It allows for viewing and adjustment of input parameters, as well as real-time monitoring of press status and error messages.

Condition: as good as new (ex-display), The Convotherm C4ET6.10ES combi oven offers three primary operating modes: hot air, steam, and combi steam. The appliance is equipped with low temperature and Delta-T settings, making it ideal for long cooking times for various foods such as meat, poultry, and fish. These settings allow the operator to cook food overnight. During prolonged, slow cooking, food retains more moisture and remains exceptionally tender. The Delta-T function uses a core temperature sensor to continuously monitor the food’s internal temperature and automatically adjusts heat for even results. The easyTouch control panel features an intuitive 9-inch full touchscreen interface. The Convotherm C4ET6.10ES combi oven is equipped with a ring indicator showing operating status in three stages: 'preheating', 'in progress', and 'ready'. This model includes an integrated on-screen help function, complete with tutorial videos to facilitate usage. The control panel features a permanent antibacterial surface to minimize bacterial transfer. Operators can program up to 399 recipes, each with up to 20 steps, ensuring consistent product output. The unit also features a self-cleaning/wash function with detergent dispensers. Comes with an additional smoker kit and function, a side-sliding door, dedicated extraction hood, and a stand. Factory warranty included; offered significantly below standard price. Electric powered Injection spritzer steam generator 3 primary operating modes: hot air, steam, and combi steam Retherm setting for optimum reheating of cooked foods Low temperature and Delta-T settings enable high-quality results through slow cooking EcoCooking setting conserves energy over extended cook times Cooking chamber accommodates 7 shelves for pans, baskets, racks, and plates Preheating and cooling functions available Core temperature probe for accurate monitoring 5-speed user-adjustable fan for uniform heat distribution Cajdsxwdayspfx Addja Eco, express, and standard cycles with automatic cleaning system Antibacterial door handle and control panel help reduce bacterial transfer Safety latch protects users from steam during operation in steam mode 208-240 V / 60 Hz / 3 phase / 25.0–28.5 A / 9–11.8 kW Overall Dimensions: 34.5 in W x 31.25 in D x 30 in H

Year of construction: 2015, condition: used, functionality: fully functional, machine/vehicle number: 1412016.02, SRU 1200x5000-EG-A-UK Vibratory Conveyor Trough 1200 x 5000 mm Original purchase price: €81,600 Negotiable Original invoice available Conveyed material: Metal mix, steel scrap Capacity: approx. 15 t/h Bulk density: 0.5 – 0.6 t/m³ Grain size: typically approx. 0 – 300 mm (~90%), max. 850 mm diagonal dimension Moisture: dry, free-flowing and easy to convey, not cohesive Temperature: cold Application: Feeding material onto the vibratory trough Trough width: 1200 mm Trough length: 5000 mm Trough height: 250 mm Inclination: horizontal Mounting: on hollow rubber springs Vibration-resistant steel construction, consisting of: the trough body, 6 mm thick, grade R St 37-2 with reinforcements bolted exciter console, stress-relieved annealed and machined bolted special discharge with flanged collar incl. 2 outlets approx. 600 mm wide the bolted wear liners for base and sides, 8 or 6 mm thick, made from wear-resistant special steel (e.g., Hardox 450 or similar) two steps: 1st step approx. 400 mm high after approx. 1,500 mm of conveying length; 2nd step approx. 200 mm high after an additional approx. 1,250 mm of conveying length Csdsxy Rqdopfx Addsaa acceleration sensor hollow rubber springs supporting structure for a trough bottom height of approx. 1,800 mm Drive: 2 vibration motors, 400 V, 50 Hz, IP 65, rated power approx. 2 x 7.5 kW = approx. 15.0 kW at 960 rpm. The amplitude can be infinitely adjusted when at a standstill. Equipped with PTC thermistors for temperature monitoring in frequency inverter operation Drive arrangement: underneath, within horizontal profile Permissible ambient temperature: -20 to +40°C This vibratory conveyor trough is used and sold in its current condition, with any and all warranties excluded. The buyer has had the opportunity to inspect the item thoroughly.

Condition: used, Year of construction: 2021, Machine Designation: Chip Drying and Cleaning System with Centrifugal Dryer and Coolant Cleaning Unit Manufacturer: T & A Trenntechnik & Anlagenbau GmbH, Ettenheim, Germany Type / Model: SCORO Z3C chip wringer system with TORNADO 200 RT-S 2-phase coolant centrifuge Year of Manufacture: 2021 Control System: Siemens S7 PLC control in accordance with EN 60204 Technical Data: • Application / Capacity: - Material: Short, free-flowing brass chips (various alloys) - Throughput: Up to 6 t / week (3-shift operation) - Max. residual moisture: 3 % - Coolant type: Water-miscible - Chip feed: Via lifting-tilting device - Discharge: Into big bag (91 × 91 × 110 cm, max. 1000 kg) • Main Components: Lifting-tilting Unit EHKG 250: • Load capacity 250 kg • Tilting angle 150° • Tilting height 2200 mm • Manual bin loading • Lifting speed 7 m/min Safety Fence: • Electrically interlocked door • Height 2500 mm • UVV-compliant safety design Scraper-Belt Chip Conveyor KF 300/380/2: • Total length ≈ 4000 mm • Discharge height 1800 mm • Conveyor width 380 mm, height 300 mm • Pitch angle 60° • Chain per DIN 8165, pitch 63 mm, breaking load 60,000 N • Gear motor drive with safety clutch and standstill monitoring • Wear-resistant manganese steel bottom lining and complete enclosure Feed Hopper: • Volume 1 m³ • Ultrasonic level sensor for automatic stop on empty Chip Wringer / Centrifuge SCORO Z3C: • Fully automatic de-oiling centrifuge for short free-flowing chips • Inlet 350 × 350 mm • Chip discharge Ø 400 mm • Motor 2.2 kW, IP54, 400 V / 50 Hz, with 24 V brake and thermal monitoring • Drum Ø 300 mm, speed 1900 rpm, slot width 0.2 mm, stainless steel screen • Throughput ≈ 400 kg brass chips (depending on chip shape and alloy) Codpfxexnl Nwj Addsaa Base Frame Centrifuge: • Steel welded construction adjusted to big bag discharge height Coolant Tank (3-chamber design): • Dimensions 600 × 600 × 350 mm with rinse pump, discharge pump and level monitoring Drip Tray: • Covers complete system footprint Electrical Cabinet: • Siemens S7 PLC • 400 V / 50 Hz supply • 24 V DC control • Operator panel mounted in door • Prepared for future integration of V200 chip crusher Paint Finish: • System painted RAL (as per customer specification) • Control cabinet RAL 7035 Documentation: • Operating instructions, spare parts list, drawings, wiring diagrams, CE declaration, test log (in German and Hungarian) Installation & Commissioning: • Includes transport, assembly, commissioning, and operator training Chip Collection Trolleys: • 16 units (600 × 600 × 600 mm, approx. 180 L each) 2-phase Coolant Centrifuge TORNADO 200 RT-S: • Stationary design for cleaning recovered coolant and drying solids • Drive motor 2.2 kW, 400 V / 50 Hz, with electric and mechanical brake • Drum speed 3900 rpm • Sludge capacity 15 kg • Drum liner NBR • Noise level < 70 dB(A) • Safety interlocks IFM & Euchner • Pump A40-110B/A (0.55 kW, approx. 60 L/min) with DN 25 suction hose • Separate electrical cabinet (400 V / 50 Hz, 24 V DC)

Condition: good (used), functionality: fully functional, R A Lamb E28.5 Section Dryer • Compact instrument that quickly dries racks of slides using a stream of warm air • Selectable air temperature from ambient to 70°C allows efficient drying of slides • Hinged lid allows warm air to escape via spaces on either side • The lid and chamber lining are made from polished stainless steel for easy cleaning • Controls are located on top to protect them from moisture when lid is open • Deep chamber holds large slide racks • Racks containing slides are placed on a grill in the glass-fronted chamber Technical Specification Dimensions, external [w x d x h], mm 285 x 245 x 129 Dimensions [w x d x h], mm 260 x 80 x 108 (chamber) Mass, kg 4.1 Electrical supply 220V to 240V, 50/60Hz Csdpfx Asu Tkcxeddsaa Good working condition. Please check out our other listings as well.

Condition: good (used), Used machine, good condition. Delivery time appr. 16 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Transport line / cooling section (nominal value: 4x2m) Cajdpjfmqq Esfx Addea each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: excellent (used), Year of construction: 2017, Snack & Filled Stick/Pillow Production Line -Production capacity: 200 kg/h -Power requirement: 62 kW, 380 V / 50 Hz Caodpfoxqmxfjx Addsa -Certification: ISO 9001 / 14001 / 18001, CE certified General description: Complete automatic line for the production of extruded snacks and filled sticks/pillows. The system is designed for continuous operation and includes all stages from raw material hydration to ready-to-season product cooling. All main components are made of stainless steel 304, ensuring full food-grade compliance and easy cleaning. Main components: -Corn moisturizing mixer (300 kg) with water dosing and metal impurity magnet. -Helix feeder with automatic extruder feeding and safety grid. -Extruder (200 kg/h) with 50 HP motor, LS inverter control, SKF bearings, 5 interchangeable dies, and air cooling system. -Air-current conveyor transferring product to the dryer. -Dryer (gas or electric) insulated double-wall stainless cylinder with inverter speed control. -Seasoning drum (Ø 85 cm × 3 m) with inverter speed control and spray coating system. -Two flavor & oil mixers, double-jacketed, 200 kg capacity each. -Flavor pump with inverter-controlled dosing. -Cutter for sticks/pillows length adjustment. -Cooling conveyor with fans for product cooling before packaging. -Butter melting tank and stuffing mixer tank, both double-jacketed, temperature-controlled. Control system: Centralized Schneider & LS electrical control panels with full motor protection, inverter speed control, and automatic temperature regulation. Overall dimensions: Approx. 15 m (L) × 3.5 m (H)

Condition: good (used), Pneumatic double diaphragm pump -Fast venting and immediate suction of the medium Caedpfx Aedwf S Uoddja -Dry running without: damage -Hermetically sealed for: moisture-sensitive liquids -Excellent for: abrasive liquids with low to medium viscosity and materials sensitive to shear forces: -Air max. Pressure: bar -Air connection: 1 "inch -Water output: l/min -Water max. Pressure: bar -Connection: B coupling -Dimensions: 480/400/H530 mm -Weight: 32 kg

Condition: used, container length: 20 ft, empty load weight: 2,100 kg, -Used -Wind and waterproof -available immediately -The price is ex depot in Munich (also available in other regions on request) -We are happy to take care of delivery and crane unloading (costs on request) Our 20-foot storage container is the perfect solution for your storage needs. It offers you a safe, flexible and cost-effective way to store your goods and materials. Whether for use on construction sites, in industry or for private purposes - this container meets the highest standards of quality and functionality. Product features: - Dimensions: 20 feet (6.06 m) long, 2.44 m wide and 2.59 m high - Volume: Approx. 33 m³, ideal for storing large quantities of goods - Material: Robust steel construction that guarantees durability and resistance - Security: Equipped with a reliable locking system and reinforced doors to optimally protect your stored goods - Weatherproof: Weatherproof and corrosion-resistant coating that protects your goods from rain, sun and other environmental influences - Ventilation: Strategically placed ventilation openings prevent the accumulation of moisture and ensure an optimal storage climate Applications: The 20 foot storage container is ideal for storing tools, machines, materials, furniture and much more. It can be used both temporarily and permanently and is ideal for construction sites, warehouses, events or as additional storage space for your company. Additional benefits: - Easy handling: Thanks to the standardized dimensions, the container is easy to transport and place. - Flexibility: The container can be used in different locations and is mobile, so you can move it if necessary. Cajdpjvyacgefx Addsa Customization: On request, we offer individual modifications to meet specific requirements, such as shelving systems or additional ventilation. Rely on our new 20-foot storage container for safe and efficient storage of your goods!

Condition: excellent (used), GFK transport box Bundeswehr container pressure-tight & waterproof, 80x60x50cm. From depot stocks of the Bundeswehr we can offer you these great boxes ! This extremely robust GFK transport box from Bundeswehr stock is not only perfectly protected against dust and water ingress, it also has a pressure equalization valve and a moisture indicator ! Through this special equipment, all kinds of goods can be stored in almost all regions of the world, because both the humidity and a fluctuating pressure can be perfectly monitored and balanced. The containers perfectly protect the packaged goods against shock and impact, against humidity and moisture and in alternating climates and extreme climatic effects ! The pictures show the box without and with interior made of solid foam - this is usually supplied, but can be easily removed. We can not guarantee that it is present in every box, so please inform us if you buy in any case can not do without the interior ! The price is always for a complete box with lid ! Dimensions: 800mm x 600mm x 500mm Capacity 240 liters Weight: 27 kg empty, 30 kg with interior made of solid foam material The containers are in a visually and technically all around good condition. Color changes, transport traces and slight adhesive residues from shipping bags, etc. are present, but do not limit the usability in any way. We have hundreds of boxes also in other sizes in stock, just ask! Product properties: - pressure- and vapor-tight (air- and watertight) - air-loadable according to LTR 8145 - provided with corrosion-resistant tension locks and - resetting carrying handles - stackable with all sizes due to the dimpled grid system The sale is exclusively to tradesmen, you will of course receive an invoice with VAT. Private buyers have the opportunity to purchase the boxes "on behalf of customers", a direct commercial sale to private individuals is expressly not ! Caodpemmfa Hjfx Addea The goods are sold under exclusion of any warranty or liability for material defects. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of obligations of the seller and for any injury to life, limb and health.

Condition: new, functionality: fully functional, Year of construction: 2025, working width: 1,380 mm, overall weight: 80 kg, empty load weight: 80 kg, operation weight: 80 kg, High-quality wall-mounted (gable) fans with dimensions of 1380 x 1380 x 450 mm and a capacity of 44,500 m³. Motor power: 1.1 kW, 3-phase. This exhaust fan is suitable for industrial or agricultural applications and is often used in pig farms, poultry houses, greenhouses, or production halls. • The unit provides effective ventilation by removing stale air, excess moisture, and unpleasant odors. • It is a push-pull fan, operating in both exhaust and intake modes. • The galvanized sheet metal and protective mesh construction ensure durability and safe operation. • The large blade diameter and powerful motor enable high airflow efficiency. Caodpfx Aoxuvatjddea

Condition: new, Year of construction: 2025, Production time of the machine approx. 3.5 months Very robust machine with high pressing force - is also suitable for producing a saleable briquette quality *depending on the material. The large press cylinder and the 65 mm briquette make this possible. Our best-selling briquetting press series Casdoffh Atspfx Addja + Tried and tested, simple technology, for extremely low susceptibility to faults + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Good price-performance ratio Options: Surcharge for cooling unit + € 3,995 net, (can also be retrofitted later) * cools the press tongs (important from 3.5 hours) and the hydraulic oil * Cooling unit recommended for regular operation of more than 3.5 hours at a time. Large pre-compressor chamber + € 1,975 net recommended for light starting materials such as wood shavings Product code: 84793010 Briquette diameter: 65 mm Front bush: 65 mm Briquette stroke max.: 50 mm Briquette stroke opt.: 50 mm Output (depending on material): up to 110 kg/h* approx. 87 kg/h in the last test. *depending on the bulk density *based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Length: 1925 mm Width: 1100 mm Height: 1500 mm Weight: 800 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo capacity: approx. 0.7 qbm Pump: 37 liters Hydraulic pre-compressor Cooling press tongs option: yes, with special accessory Coolable press tongs Cooling of the pressing tongs via water tank (to be procured on site) Hydraulic oil cooling option: yes Fill level monitoring option: yes Briquette option: yes (depending on material) CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18 % - Chip length maximum 15 mm - Installation temperature: tempered room at a minimum of +5°C - The feed must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear may result

Condition: as good as new (ex-display), Year of construction: 2024, Special price for our demonstration machine Another machine, available now (ex works in Neckartailfingen) Approx. 8 operating hours. Suitable for shredding all types of leftover wood and also pallet sections. The pallet would need to be prepared with a jigsaw or chainsaw so that it fits vertically into the hopper - see Figure 2. Ideally, it would be approximately 40x20x20 cm so that the wood can lie flat on the slider floor. This is where the machine works most effectively. A hydraulic slider runs at the bottom of the shredder, which pushes the wood against the rotor depending on the load. The material is shredded until it passes through the screen basket. Throughput up to 200 kg per hour *depending on the screen and how well the material is prepared. *Conveyor belt and overhead magnet available at an additional cost. + Powerful 18.5 kW motor, + Concave blades, + Large high-performance gearbox, + Special, load-dependent slide control, Customs tariff number: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Blades: 15, multi-rotatable Option: double row of blades + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutter opening: 630 x 820 mm Filling volume: approx. 0.6 m³ Hydraulic slide gate Screen perforation of your choice (10 - 30 mm) Suction nozzle diameter: 160 mm Weight: approx. 1,300 kg (depending on accessories) Dimensions (L x W x H): approx. 1,737 x 1,167 x 1,650 mm Moisture content: 30% dry Included as standard: - V-rotor for maximum throughput - Control cabinet with Siemens PLC control - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idling Cedpfjdwktksx Addeaa - Speed 70-90 rpm for high throughput - Cyclic control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant. - MADE IN GERMANY . Shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) +€2,080 net - Articulated conveyor belt +€8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet +€5,980 net - Conveyor belt and overbelt magnet control +€2,750 net (Start and stop synchronized with the shredder) - Extend hopper +€940 net - Eco-rings: +€1,980 net (recommended for more than 15% hardwood) - Special scraper +€990 net (recommended for veneer or paper) - Double Knife series + €995 net . Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear.

Condition: refurbished (used), Year of construction: 2004, functionality: fully functional, Briquetting press for wood or wood-like materials Throughput: approx. 80 - 100 kg/h Briquette: 60 mm cylindrical Motor: 7.5 kW Oil heating 6,374 operating hours Dimensions: approx. 2150 x 1700 x 1400 mm Container size: 1400 x 1400 x 920 mm Optional: Extraction unit available as a hopper attachment. Requirements: Ideal input material: chip length less than 25 mm Moisture content: 6–12% ATRO Machine is suitable for intermittent operation, e.g. up to 2 hours briquetting; 1 hour pause, etc. Cedpjw Hpizjfx Addeaa If the machine is to run continuously for more than 2 hours at a time, an optional cooling system must be connected.

Condition: new, Year of construction: 2025, Single-shaft shredder MRZ 530 Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher Cjdpfx Asd Db N Ioddsaa • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2025, Delivery time approx. 3-4 months MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slider Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times Cajdpfxed Dgw Ue Addja - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) + €2,140 net - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €5,980 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - Moisture content (dry) must be below 30% - Installation temperature: temperature-controlled room at least +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: like new (used), Year of construction: 2024, operating hours: 29 h, *one machine is ready for delivery and ready produced Press can only be supplied with a system component such as a chipper, cutting mill, hammer mill, screw conveyor, conveyor belt with overbelt magnet or suction RUF briquetting press for rectangular briquettes Very robust and established machine The ideal machine for professional, industrial briquette sellers. Classic type - throughput up to 425 kg / h * depending on the material Options for an extra charge: Plant construction / mütek system technology: - mütek shredder MRZ shredding technology - conveyor belts - Overbelt magnets - Extraction systems, optionally with rotary valve - screw conveyors - silos - Control links of all kinds - semi-automatic packaging technology Press: - Packing table with drawer - Top-mounted silo with discharge Your advantages: Most important point: + Very established, well-engineered die press thanks to 25 years of experience. The difficulty and the know-how lies in the detail. For example, valves and cylinder seals of the highest quality. Cedefhql Tspfx Addjaa + 24h operation possible + Longevity + Low maintenance costs + Compact structure + High energy efficiency thanks to innovative hydraulics Technical data briquetting press: Throughput: up to 425 kg / h * * depending on the bulk weight of your raw material * based on a bulk weight of 200 kg per cubic meter Detailed information after a successful test with your material. If no test material is made available to us, we cannot make any statements about the briquette quality and throughput. Briquette dimensions: 150 x 60 mm Briquette length: 40 to 105 mm (adjustable) Hydraulic pre-compressor Main hydraulic compressor Pressing pressure: up to approx. 1700 kg / cm² Hydraulic system with 260 liter oil tank Pump motor: 30 kW / 400V / 50Hz / 3 ph Manual operation of all cylinders "Dustproof" switch cabinet with PLC control and touch display Total power consumption of the briquette press: approx. 33 KW Muxzr8 Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 15% - Maximum chip length: 20 x 2 x 2 mm - temperature where machine is placed + 8 degrees - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear.

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm Caodsff Sbiepfx Addsa

Condition: good (used), Refurbished machine Basic machine starts at a price of 147.700 € net *Options at additional cost, see below with a full 1 year warranty Ready for delivery approx. 16 weeks after ordering Technical specifications: Throughput up to 1200 kg / h depending on the material (e.g. sawdust with a bulk weight of 150/180 kg / qbm) Briquette Ø 75 mm including 2 m press channel Main motor power 45 kW Feed screw gear motor 2 x 2.2 kw Compressor screw 2 x 5.5 kw Distribution auger 2.2 kw Hydraulic pump motor 0.37 kW Total connected load 65 KW Control panel with plain text display for operating states and utilization display for main drive and feed screws PLC control Siemens S7 / 300 with operating hours counter in the control cabinet Machine hat CE mark Automatic start / stop function of the machine Dimensions 3100x860x1800 mm lxwxh Weight 4500 kg Options: -Silo for MAP series Storage silo above the machine - Contents approx. 6 square meters, stable steel construction with agitator discharge and level indicator. 19,700 € net plus VAT. *only possible for one presse MAP 1200 below the silo if you need to place two machines MAP 1200 below one silo it needs to be build completely different. the price for this silo is 37.900 € net -Temperature control device for the pressing tools to maintain the temperature for optimal briquette size. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - must be left for operation including corresponding control Cedpfx Ae E Dquoddjaa € 7.850 net Oil heater 1.950 € net -Guillotine, to cut the briquettes to length Create a compressed air connection on site € 6,940 net plus VAT -Transport line / cooling section (nominal value: 4x2m) 990 euros net per 2 meters - Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site to install one press) based on effort and upon proof against separate invoice. The following sentences apply: Service technician/mechatronics technician per assembly and hour of travel: €129.00 Overtime: 25% surcharge 50% surcharge per Saturday and night hour 100% surcharge for every Sunday and public holiday hour Release per fitter per day: country dependent Per car, van and driving kilometer: €0.98 / km Arrival and overnight stay against receipt or flat rate bill at the client's expense. . Test with the respective customer material: (up to a maximum of 750 kg) - €1,970 net flat rate --- Recognition from the raw material: - The moisture content must be between a minimum of 6 and a maximum of 18% - Maximum span 20 mm - Excessive temperature: temperate room at at least + 5 ° C. - The loading must be free of metals and mineral impurities. This and the pressing tools and / or responsible wear can be the result

Condition: new, Year of construction: 2023, The ideal machine for shredding hardwood and softwood Another machine, available immediately (ex works Neckartailfingen) . Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Knives: 14+2 pieces, 40x40mm, multiple rotatable, Cajdped E R D Ssfx Addsa Rotor diameter: 260 mm, Control: Omron SPS, Cutting unit opening 600 x 800 mm, hopper volume approx. 0.6 qbm, hydraulically operated pusher Screen perforation of your choice (12 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm . The following options are available at extra cost: - Additional row of knives + 995 € net (28 instead of 14) - Surcharge for 4-sided segment shelf + € 2,170 net (prevents blocking of the pusher. Recommended for materials with a thickness of less than 3 mm) - Raise shredder by 30 cm (preparation for conveyor belt) + € 1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) - Special bearing +1,540 € (rarely required. Closed, even more stable rotor bearing. Possibly a consideration for sieves smaller than 15 mm or with a lot of fines. Not necessary if the bearings are lubricated with grease every approx. 2 weeks during operation) . Requirements for the raw material: - The moisture content (atro) must be below 30 % - Metals and mineral impurities such as sand, stones etc. lead to increased wear. . We will be happy to carry out a free test with your material and invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: new, Year of construction: 2025, production time appr. 4 months * for suction perception, see picture 4 and 5 Tariff number: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 ph including turbo coupling, Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3ph Knife: 76 pieces, rotatable Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control: PLC Siemens S7-1200 Funnel opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 square meters hydraulically operated slide Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (lxwxh) approx. 2765 x 2520 x 1730 mm Turbo coupling Included as standard: - V-rotor for other throughput - 2nd row of knives on the rotor - Control cabinet with Siemens PLC control - automatic star / delta start - fast hydraulics - Automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - Clock control to avoid idle times Casdpfxjd Hkqho Addja - Performance-increasing step control of the hydraulic slide - Pertinax guides for hydraulic slides - anti-vibration machine feet - CE conformity The shredder is for shredding natural wood, chipboard and MDF board other materials after testing and approval by the manufacturer Recognition from the raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. Interests to interests wear

Condition: as good as new (ex-display), Year of construction: 2024, Machine for sale at a special price Another machine, available immediately (ex works Neckartailfingen) * Including 1 year warranty. Your advantages: + Very robust, simple technology + Top price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning / established machine Including control cabinet with timer operation Casdjd Nnwlepfx Addja Press is switched on manually and then runs until the time set on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Briquette dimensions: approx. 30 x 30 mm (square), Briquette length: 5-40 mm *depending on material Throughput capacity: up to a maximum of 20 kg/h. *depending on material Machine dimensions approx. 137 x 75 x 148 cm (length x width x height), Weight of the machine: approx. 250 kg, Capacity of the silo: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust smaller than 15 mm in length -Moisture content less than 18 % ATRO -Sand, stones, metals and minerals increase wear --- Options at extra charge: --Timer function + 490 € net Machine is started manually and switches off automatically after a set time X. -Level indicator for automatic operation + 1450 € net Press starts and then stops automatically * NEW !!! Also available in 230 Volt, Motor then 3 kW instead of 2.2 kW, Surcharge + 890 € net (delivery time then approx. 8 weeks) - Special pressing units + 2.950 € net ---

Condition: as good as new (ex-display), Year of construction: 2025, showroom machine machine available Advantages: + special rotor with reduced knife protrusion + Motor 22 kW + effective square knife * for pallets: up to 10 pallets per hour * depending on the sieve and material. With smaller residual wood, significantly more. Engine: 22 kW; 400 V - 50 Hz - 3 ph, Sieve: 15/20 mm hydraulically operated slide Current screen perforation (15/20 mm) * can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: The color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star / delta start - fast hydraulics - automobile. OFF when the rotor is idling Codpfxjdv Eu Hj Addoaa - Speed ​​70-90 rpm for high throughput - cycle control to avoid idle times, - performance-increasing step control of the hydraulic slide, - Pertinax guides for hydraulic slides, - vibration-damping machine feet, - CE conform. The following options are available at an additional cost: - Additional row of knives + € 2,790 - segment bottom + € 6,890 (recommended for materials with a wall thickness thinner than 3 mm) - Special K-rotor storage + € 3,480 If necessary, consider shredding plastic with sieves smaller than 15 mm or with a lot of fines. If the bearings are lubricated with grease every approx. 4 weeks in operation, this is not necessary) - Raise the shredder by 30 cm (preparation for conveyor belt) + € 2.480 net - Angled conveyor belt (discharge height approx. 220 cm) + € 12.980 net - Overbelt magnet + € 5.980 net - Control conveyor belt and overbelt magnet + € 2.750 net (Start and stop synchronized with the hacker) - Exhibition hopper 1500x1500 mm + € 3.480 net Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2025, one machine ready produced Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood Cjdpfxogbkkrj Addsaa + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Extraction nozzle Ø (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput - Fast hydraulics, for increased throughput - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear