Used Moisture for sale (273)

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Nodpfx Aowp Rqfeh Rskw Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, Year of construction: 2025, Bending machine PROD-MASZ to the plate ZGR 2640/1.2 is a sensational machine for precision bending of all types of metal sheets (steel 1.2mm, titanium zinc 1.2mm, aluminum of 1.5 mm, copper sheet 0.8 mm). Equipped with a rack supporting plate, two front bumpers, bending angle measurement, a single lock of bending angle, turnbuckles, eccentric mechanisms. Each part of the machine is adjustable, which allows for adjustment of the arc bending. Used in the device locking system (set by the operator) allows you to achieve the desired angle of bending. Table rear and front bumpers are made of galvanized racks. Ideal for all kinds of steel treatments - wherever the roof is exposed to moisture infiltration. Proper execution of these connections certainly prolong the life of the roof. By hers construction she can be used not only for bending panels with both the ferrous metal, sheets of plastic and fiberboard. - Max. bending angle: 145 degrees - Rotary shears cut to full working length - Thickness of bending bar: 24 mm - Protractor - Weight: 350 kg Rotary shears (max. plate gauge 0,8 mm / Steel) + 350 Euro - The machine have certificate CE and 12 months warranty. Nkodpedad Adjfx Ah Rew Only shipping is possible Delivery every week Price excl. shipping We provide invoices with 0% of tax.

Condition: used, - Serial number: 10114243 - 2 levels, 5/10 trays, 400x600 mm - Year: 04-2007 - Model: Haube.SC - Programmable digital control panel - LED lighting - 8-speed ventilation - Steam injection - Steam function - Voltage: 230V - Refurbished equipment: The equipment is reconditioned upon order; lead times for servicing and delivery are agreed upon at that time (please inquire for the post-refurbishment price) - Professional convection oven Wiesheu is widely used for baking all types of bakery products: bread rolls, croissants, cookies, etc. The Wiesheu Euromat is a classic convection oven featuring intelligent controls. The steam system ensures baked goods with a golden, crisp and highly appetizing crust. Furthermore, this oven can serve as an attractive centerpiece for any pastry shop, bakery, or retail counter thanks to its appealing design, while the visibility of the baking process helps increase sales of all products. Nksdpfx Ajyabi Seh Rew - Optimal air distribution ensures uniform baking results in the hot air oven. HUMIDIFICATION: Rapid steam generation with the right amount of moisture for each type of pastry.

Condition: new, Year of construction: 2025, 🚢 20ft Storage Container – Like New (Year of Manufacture 2025 / 2026) – Available Immediately! High-quality shipping container in nearly new condition – perfect for use as storage space, workshop, site container, or for professional transport applications. ⭐ Your Advantages at a Glance 🆕 Year of manufacture 2025 / 2026 – like new 💪 Very robust steel construction (2 mm wall thickness) 🌧️ Wind- and waterproof 🔐 Securely lockable with 4-bar door locking system 🚚 Equipped with CSC plate – suitable for global shipping 🌬️ Ventilation system to prevent moisture build-up 🪵 Premium wooden floor 🛠️ Forklift pockets integrated in the base 📏 Dimensions & Technical Specifications 📐 External dimensions: 6,058 × 2,438 × 2,591 mm 📦 Internal dimensions: 5,898 × 2,350 × 2,390 mm 🚪 Door opening: 2,343 mm 🧱 Volume: approx. 33 m³ ⚖️ Empty weight: approx. 2.25 t 🏋️ Load capacity: up to 30 t These containers impress with their durability, security, and versatility – an ideal solution for commercial, construction, trade, or demanding private use. 📬 Contact us now – we will provide you with a customized offer! 👀 Additional container sizes and variants available. 🚛 Nationwide delivery within Germany possible (for an additional charge). Nksdpfx Aorvg Rtoh Rsw

Condition: used, Year of construction: 2018, Pulsotronic metal detector, Type: M-Pulse 2 BD-HD 500×175 LPW MFT, manufactured in 2018. It’s an ideal choice for companies in the food processing, meat, dairy, bakery, and fruit and vegetable sectors, as well as other industries where product purity and quality control are essential. This model features high detection sensitivity, durable construction, and a user-friendly control panel. Thanks to the compact detection tunnel dimensions (500×175 mm), it’s perfect for production lines with limited space. The device is built for demanding environments, its robust housing resists moisture, temperature changes, and dust, making it well-suited for processing facilities. Technical specification: Manufacturer: Pulsotronic Type: M-Pulse 2 BD-HD 500×175 LPW MFT Detection tunnel dimensions: 500×175 mm Year of production: 2018 Nkjdpfxswk Hg So Ah Rsw Power supply: 115/230 VAC, 1L/N/PE Power consumption: max. 16 A Frequency: 50–60 Hz The machine can be easily integrated with various conveying systems and packaging, sorting, or weighing lines. It is suitable for detecting metal contaminants in both packaged and unpackaged products. Thanks to M-Pulse 2 technology, this detector ensures high sensitivity to ferrous, non-ferrous, and stainless-steel particles – even in wet or conductive products. Automatic calibration and digital compensation ensure stable performance without frequent adjustments. Applications: quality control of food products (meat, dairy, bakery goods, fruits, vegetables, ready meals), contamination detection in chemical and pharmaceutical production, metal detection in bulk, liquid, or individually packed materials.

Condition: new, Year of construction: 2022, The FRÖLING Turbomat is a fully automatic, unique heating system designed for various types of wood materials. In addition to wood chips, it is also suitable for burning other dry fuels (with up to 35% moisture content, such as wood industry materials and pellets). Fuel supply, combustion, cleaning, and ash removal are all performed completely automatically. Technical specifications Njdpfx Ahevf Et Is Rokw Nominal heat output [kW]: 550 Flue pipe diameter [mm]: 350 Total dry weight including attachments [kg]: 8470 Heat exchanger water capacity [l]: 1040 Maximum permitted operating temperature [°C]: 90 Minimum boiler return temperature [°C]: 65 Maximum permitted working over-pressure [bar]: 6 Flue gas temperature (NL / PL) [°C]: 140/110 The price does not include the cost of storage, transport, installation and commissioning.

Year of construction: 2024, condition: new, For sale: drying system - 1T 184 TPR Model, (Mobile Conveyor Belt) We offer a high quality drying system, ideal for drying wood sawdust, produce, recyclable waste, food ingredients. Below we present the design details and features of the drying system: Design data: - Product handled: sawdust - Physical appearance:Loose - ˃ 1 mm - Initial moisture content: 55%, 50%, 40% - Final moisture content: 12% - Wet production: 4,00 t/h, 4,50 t/h, 5,65 t/h - Dry production: 2,05 t/h, 2,55 t/h, 3,85 t/h - Drying air temperature: 80 °C - Thermal energy consumed: 1.800 - 2.350 kWh - Max. evaporated water per hour: 1.800 - 1.955 Kg/h Installed electrical power: - Feeding cooker: 5,5 kW (x2) - Drying belt: 2,2 kW - Unloading equipment: 5,5 kW - Exhaust fans: 22,00 kW (x3) - Cleaning fans: 4 kW (x2) - Total installed power: Approx. 92.70 kW Water-to-air heat exchanger: - Recommended thermal capacity: 2.600 kW - Water temperature: 90 °C on - 70 °C off Dimensions: - External dimensions of dryer frame: Approx. 22 m long, 6 m wide - Drying belt surface: 72 m² Nsdpfeua D U Ijx Ah Rjkw - Unloading equipment: 5,500 mm x Ø 300 mm - Feeding trough: Approx. 1.00 m³ - Number of exhaust fans: 3 - Number of water-to-air heat exchangers: 4 Technical description: - Feeding system: Adjustable pulley conveyor with level sensor. - Drying table: Modular design with inspection windows. - Drying belt: Polyester fabric conveyor belt with steel rollers. - Thermal insulation: 50 mm thick rock wool with Magnelis® cladding. - Mixing brush: Painted steel mixing brush. - Base frame: Folded steel plates with reinforcing profiles. - Drying belt cleaning system: High pressure air and water spraying system. - Water spraying system: Closed circuit water spraying system. - Stairs and access: Secure access stairs and walkways. - Unloading equipment:Steel pulley unloader with motor. - Heat exchangers: High efficiency steel finned heat exchangers. - Air exhaust fan: Centrifugal fans with vibration damping connections. - Heat recovery: Hot air return duct. - Machine enclosure: Prefabricated enclosure made of insulated sandwich panels. - Dust filters: dust filters on the air intake grille. - Paint cycle: Phosphating, passivation, polyester powder coating. - Electrical control panel with PLC: SCHNEIDER electrical and PLC components, HMI control panel. - Humidity control system: PT 100 temperature sensors. - Remote service: direct connection via Internet. - Input and output humidity sensors: 4-20 mA adjustment. For further information and quotation please contact us! We look forward to your interest! Price: 530.000 Eur

Condition: new, 20-26-537/1 FALACH hydraulic briquetting press (new) Type 50 Briquette diameter 50mm Press capacity 40 - 60 kg / hour Briquette length approx. adjustable 35 mm Hopper volume 0.38 m3 Pump motor input 5.5 kW Power consumption 3.8 kW / hour Nkjdpoxrn R Ejfx Ah Rjw Required input voltage and current 3x400V, 16 A Oil cooler yes Operation continuous Automatic reverse of support wheels yes Automatic switching-out yes Maximum percentage of moisture 15 % Specific weight of briquettes 900 kg / m3 Maximum noise level 68 dB Transport dimensions 1860 - 890 - 1100 mm Weight 390 kg Price 13 030 Eur (EXW Jonava, Lithuania)

Condition: new, 20-26-537/4 FALACH hydraulic briquetting press (new) Type CUBE 20 Briquette diameter 30 x 30 mm Nedpfx Ajxrn Uwsh Rokw Press capacity 10-25 kg/hour Briquette length approx. 6-50 mm Hopper volume 0,28 m3 Pump motor input 2,2 kW Power consumption 1,1 kW/hour Required input voltage and current 3x400V, 16 A Oil cooler no Operation continuous Automatic reverse of support wheels no Automatic switching-out no Maximum percentage of moisture 15 % Specific weight of briquettes 900-1100 kg/m3 Maximum noise level 62 dB Transport dimensions 1300-740-1120 mm Weight 233 kg Price 8190 Eur (EXW Jonava, Lithuania)

Condition: new, 20-26-537 FALACH hydraulic briquetting press (new) Type Falach 35 Briquette diameter 50mm Press capacity 25 - 40 kg / hour Briquette length approx. 20-40 mm Hopper volume 0.38 m3 Pump motor input 4 kW Power consumption 2.2 kW / hour Required input voltage 3x400V, 16 A Oil cooler no Operation continuous Automatic reverse of support wheels yes Automatic switching-out yes Maximum percentage of moisture 15 % Specific weight of briquettes 900 kg / m3 Maximum noise level 68 dB Transport dimensions 1860 - 890 - 1100 mm Weight 400 kg Price 11 160 Eur (EXW Jonava, Lithuania) Nsdpfxjxrn Dxo Ah Rokw

Condition: new, 20-26-537/3 FALACH hydraulic briquetting press (new) Type 100 Briquette diameter 70 mm Press capacity 90 - 120 kg / hour Briquette length approx. adjustable 45 mm Hopper volume 0,75 m3 Njdpfx Aoxrn Ukjh Rjkw Pump motor input 11 kW Power consumption 8,2 kW/ hour Required input voltage and current 3x400V, 32 A Oil cooler yes Operation continuous Automatic reverse of support wheels yes Automatic switching-out yes Maximum percentage of moisture 15 % Specific weight of briquettes 900-1100 kg/m3 Maximum noise level 68 dB Transport dimensions 2220 - 1200 – 1510 mm Weight 810 kg Price 26 230 Eur (EXW Jonava, Lithuania)

Condition: new, 20-26-537/2 FALACH hydraulic briquetting press (new) Type 70 Briquette diameter 70 mm Press capacity 60 - 80 kg / hour Briquette length approx. 40 – 60 mm Hopper volume 0,75 m3 Pump motor input 7,5 kW Power consumption 4,9 kW/ hour Required input voltage and current 3x400V, 25 A Oil cooler no Operation continuous Automatic reverse of support wheels yes Automatic switching-out yes Maximum percentage of moisture 15 % Specific weight of briquettes 900-1100 kg/m3 Maximum noise level 68 dB Nsdpfx Asxrn Tgoh Rokw Transport dimensions 2220 - 1200 – 1510 mm Weight 840 kg Price 20 270 Eur (EXW Jonava, Lithuania)

Condition: new, Year of construction: 2025, Hot Air Lance HL-1 is a high-quality and efficient equipment. Hot Air Lance for pavement crack sealing preparation is a self-contained mobile unit for cleaning and drying of cracks, joints, potholes and chips in asphalted and concrete road surfaces, before pouring them with bitumen or bitumen polymeric materials. Powerful hot air flow removes moisture and particles of debris, grass, soil, dust, dirt, small stones, etc. leaving cracks dry, clean and ready to be filled with bitumen materials. Nodpfsvpqp Ajx Ah Rjkw Reasons to Buy Hot Air Lance from TICAB • Low price because of no mediators. • Always in stock. • 1-year warranty. • Full support from the manufacturer. Technical specifications: - Propane gas (consumption 5 kg / h); - Gas working pressure: 0.2-0.3 bar; - Gas bottle capacity - 50 l; - Compressor unit weight - 107 kg; - Output air temperature: not less than 400 ° C; - Hot Air Lance weight - 6 kg - Hot Air Lance length: 1500 mm; - Wheeled stand weight: 4kg; - Compressor capacity - 600 l / min; - Engine power: 7 hp.

Condition: as good as new (ex-display), Demonstrator with 7 operating hours Another machine available immediately (ex works in Neckartailfingen) MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slide gate Nkodpfev Sqrpex Ah Rsw Screen perforation of your choice (10 - 40 mm) Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Included: - Raise the shredder by 30 cm (prepared for conveyor belt) Additional shredder options: - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €6,780 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: as good as new (ex-display), Year of construction: 2024, Primary crusher Basic machine starting from € 29,950 net *Options against surcharge Ideal for pre-crushing bulky materials such as pallets, boards, beams, fruit crates, polystyrene, plastics and much more. For the production of wood chips, the primary crusher can also be installed directly above a single-shaft shredder Machine in pre-production * Special options available at extra cost Your advantages: + Volume reduction of up to 70 + Significantly lower transportation costs Nksdpfx Ajfd Icish Rjw + Low disposal costs + Production of fuel material + Also ideal upstream of a single-shaft shredder for the production of wood chips Weight: 1,200 kg Dimensions 2050x850x1600 mm Cutting unit opening 1300x700 mm *Optionally also available in 1600x700 mm (motor then 11 kW) (surcharge + 4.995 € net) Throughput: up to 50 pallets/pieces per hour *depending on material Motor: 7.5 kW Options: Industrial top hopper (closed on 3 sides) + € 4,950 net Extra emergency / off button + 495 € net 200 mm extension + 497 € net Requirements for the raw material: - Moisture content less than 30 % ATRO - The machine must be installed in accordance with CE guidelines or secured on site against access from below (into the cutting unit) - Pallets up to a dimension of 1200x800 mm can be processed Longer parts also work on edge

Condition: good (used), Used machine, good condition. Delivery time appr. 16 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Transport line / cooling section (nominal value: 4x2m) each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge Nedofmqq Ejpfx Ah Rskw 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: new, Year of construction: 2026, Production time of the machine approx. 3.5 months Very robust machine with high pressing force - is also suitable for producing a saleable briquette quality *depending on the material. The large press cylinder and the 65 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to faults + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Good price-performance ratio Options: Surcharge for cooling unit + € 3,995 net, (can also be retrofitted later) * cools the press tongs (important from 3.5 hours) and the hydraulic oil * Cooling unit recommended for regular operation of more than 3.5 hours at a time. Large pre-compressor chamber + € 1,975 net recommended for light starting materials such as wood shavings Product code: 84793010 Briquette diameter: 65 mm Front bush: 65 mm Briquette stroke max.: 50 mm Briquette stroke opt.: 50 mm Output (depending on material): up to 110 kg/h* approx. 87 kg/h in the last test. *depending on the bulk density *based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 Volt / 50 Hz / 3-phase Length: 1925 mm Width: 1100 mm Height: 1500 mm Weight: 800 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo capacity: approx. 0.7 qbm Pump: 37 liters Hydraulic pre-compressor Cooling press tongs option: yes, with special accessory Coolable press tongs Cooling of the pressing tongs via water tank (to be procured on site) Nkjdpfjffh Atox Ah Rew Hydraulic oil cooling option: yes Fill level monitoring option: yes Briquette option: yes (depending on material) CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18 % - Chip length maximum 15 mm - Installation temperature: tempered room at a minimum of +5°C - The feed must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear may result

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € Nodpfx Aeff Sbioh Rekw - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm

Condition: like new (used), Year of construction: 2024, operating hours: 29 h, *one machine is ready for delivery and ready produced Press can only be supplied with a system component such as a chipper, cutting mill, hammer mill, screw conveyor, conveyor belt with overbelt magnet or suction RUF briquetting press for rectangular briquettes Very robust and established machine The ideal machine for professional, industrial briquette sellers. Nsdpfx Ahsfhql Tj Rjkw Classic type - throughput up to 425 kg / h * depending on the material Options for an extra charge: Plant construction / mütek system technology: - mütek shredder MRZ shredding technology - conveyor belts - Overbelt magnets - Extraction systems, optionally with rotary valve - screw conveyors - silos - Control links of all kinds - semi-automatic packaging technology Press: - Packing table with drawer - Top-mounted silo with discharge Your advantages: Most important point: + Very established, well-engineered die press thanks to 25 years of experience. The difficulty and the know-how lies in the detail. For example, valves and cylinder seals of the highest quality. + 24h operation possible + Longevity + Low maintenance costs + Compact structure + High energy efficiency thanks to innovative hydraulics Technical data briquetting press: Throughput: up to 425 kg / h * * depending on the bulk weight of your raw material * based on a bulk weight of 200 kg per cubic meter Detailed information after a successful test with your material. If no test material is made available to us, we cannot make any statements about the briquette quality and throughput. Briquette dimensions: 150 x 60 mm Briquette length: 40 to 105 mm (adjustable) Hydraulic pre-compressor Main hydraulic compressor Pressing pressure: up to approx. 1700 kg / cm² Hydraulic system with 260 liter oil tank Pump motor: 30 kW / 400V / 50Hz / 3 ph Manual operation of all cylinders "Dustproof" switch cabinet with PLC control and touch display Total power consumption of the briquette press: approx. 33 KW Muxzr8 Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 15% - Maximum chip length: 20 x 2 x 2 mm - temperature where machine is placed + 8 degrees - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear.

Condition: as good as new (ex-display), Year of construction: 2025, showroom machine machine available Advantages: + special rotor with reduced knife protrusion + Motor 22 kW + effective square knife * for pallets: up to 10 pallets per hour * depending on the sieve and material. With smaller residual wood, significantly more. Engine: 22 kW; 400 V - 50 Hz - 3 ph, Sieve: 15/20 mm hydraulically operated slide Current screen perforation (15/20 mm) * can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: The color of the system may vary Weight: 1920 kg. Nodpfodv Eu Hsx Ah Rskw Included as standard: - Control cabinet with PLC control - automatic star / delta start - fast hydraulics - automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - cycle control to avoid idle times, - performance-increasing step control of the hydraulic slide, - Pertinax guides for hydraulic slides, - vibration-damping machine feet, - CE conform. The following options are available at an additional cost: - Additional row of knives + € 2,790 - segment bottom + € 6,890 (recommended for materials with a wall thickness thinner than 3 mm) - Special K-rotor storage + € 3,480 If necessary, consider shredding plastic with sieves smaller than 15 mm or with a lot of fines. If the bearings are lubricated with grease every approx. 4 weeks in operation, this is not necessary) - Raise the shredder by 30 cm (preparation for conveyor belt) + € 2.480 net - Angled conveyor belt (discharge height approx. 220 cm) + € 12.980 net - Overbelt magnet + € 5.980 net - Control conveyor belt and overbelt magnet + € 2.750 net (Start and stop synchronized with the hacker) - Exhibition hopper 1500x1500 mm + € 3.480 net Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: good (used), Refurbished machine Basic machine starts at a price of 147.700 € net Nedpfx Aj E Dqueh Rokw *Options at additional cost, see below with a full 1 year warranty Ready for delivery approx. 16 weeks after ordering Technical specifications: Throughput up to 1200 kg / h depending on the material (e.g. sawdust with a bulk weight of 150/180 kg / qbm) Briquette Ø 75 mm including 2 m press channel Main motor power 45 kW Feed screw gear motor 2 x 2.2 kw Compressor screw 2 x 5.5 kw Distribution auger 2.2 kw Hydraulic pump motor 0.37 kW Total connected load 65 KW Control panel with plain text display for operating states and utilization display for main drive and feed screws PLC control Siemens S7 / 300 with operating hours counter in the control cabinet Machine hat CE mark Automatic start / stop function of the machine Dimensions 3100x860x1800 mm lxwxh Weight 4500 kg Options: -Silo for MAP series Storage silo above the machine - Contents approx. 6 square meters, stable steel construction with agitator discharge and level indicator. 19,700 € net plus VAT. *only possible for one presse MAP 1200 below the silo if you need to place two machines MAP 1200 below one silo it needs to be build completely different. the price for this silo is 37.900 € net -Temperature control device for the pressing tools to maintain the temperature for optimal briquette size. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - must be left for operation including corresponding control € 7.850 net Oil heater 1.950 € net -Guillotine, to cut the briquettes to length Create a compressed air connection on site € 6,940 net plus VAT -Transport line / cooling section (nominal value: 4x2m) 990 euros net per 2 meters - Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site to install one press) based on effort and upon proof against separate invoice. The following sentences apply: Service technician/mechatronics technician per assembly and hour of travel: €129.00 Overtime: 25% surcharge 50% surcharge per Saturday and night hour 100% surcharge for every Sunday and public holiday hour Release per fitter per day: country dependent Per car, van and driving kilometer: €0.98 / km Arrival and overnight stay against receipt or flat rate bill at the client's expense. . Test with the respective customer material: (up to a maximum of 750 kg) - €1,970 net flat rate --- Recognition from the raw material: - The moisture content must be between a minimum of 6 and a maximum of 18% - Maximum span 20 mm - Excessive temperature: temperate room at at least + 5 ° C. - The loading must be free of metals and mineral impurities. This and the pressing tools and / or responsible wear can be the result

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% Nkjdpfed Db N Isx Ah Rjw - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2026, Delivery time approx. 3-4 months MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slider Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) + €2,140 net - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €5,980 net - Conveyor belt and overbelt magnet control + €2,750 net Nkodpfsd Dgw Uex Ah Row (Start and stop synchronized with the shredder) Raw material requirements: - Moisture content (dry) must be below 30% - Installation temperature: temperature-controlled room at least +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: used, Granulation and packaging line. Model: HM700E PRO 11KW Year of manufacture: 2022 It includes: Hammer mill - shredder Chip mixer Chip feeder Granulator Vibrating table Product feed belt (conveyor belt) Pellet hopper with packaging equipment Bag sealer and chip moisture meter Hammer mill with cyclone Motor: 11 kW / 400 V Productivity: 300 - 700 kg / h Weight: 360 kg Soft start installed Cutting system 16 hammers Chip mixer: Volume: 1.0 m³ Chip feeder: Motor: 3.3 kW / 380V Feeds up to 800kg / h Granulator: Motor: 22 kW / 380V/50hz; Productivity: 300 - 700 kg/h Weight: 590kg Soft start installed Vibrating table: Weight 90kg Product feed belt (conveyor belt): Dimensions: 5m × 0.4m. Nedpoxcy D Eofx Ah Rskw Automated packaging equipment: Dimensions: 1, 90x2, 50x2, 30 Volume: 1.5m³ Packing in bags: 1 - 50kg Equipped with two types of scales Bag sealer 220V Moisture meter

Condition: new, Year of construction: 2024, functionality: fully functional, The SR 8 screw compactor from Koltex is an advanced solution designed for drying film flakes and preparing them for the extrusion process. This innovative machine effectively reduces the moisture content of the material to around 5%, significantly impacting the quality of the final recycled product. Modular construction The machine can be customized to meet the individual needs and requirements of the customer, allowing it to be used to its optimum potential in a wide variety of applications. Reliability The use of renowned drive components with a high degree of efficiency reduces operating costs while extending service intervals. Intelligent machine operation Touch panel with intuitive interface for easy control and monitoring of the working process. Space-saving The press is designed to be compact, saving valuable space in the workplace. Nodpfjuqwzwjx Ah Rjkw Capacity (LDPE film): 1500 KG/H Auger diameter: 500 mm Engine power: 45 kW Scraping power: 7.5 kW Feed size: 760x650 Overall dimensions: 6097x1833x2729 Weight: 6800 kg