Used Mori Seiki Gv 503 for sale (188)

Condition: used, Year of construction: 2012, turning diameter 370 mm turning length 424 mm control MSX-711-IV Mori Seiki swing diameter 370 mm X1- Axis 380 mm X2- Axis 155 mm Z1- Axis 460+155 mm Z2- Axis 610 mm y-axis +/- 105 mm B - axis +/- 120 ° bar material dia. 65 mm Dkodjzfauiepfx Am Top speed spindle max. S1 5.000 / S2 6.000 U/min. spindle bore S1/S2 65/38 mm 12000 1/min tool taper Capto C5 toolpiece magazine: chain magazine 76 Stück total power requirement 45 kW weight of the machine ca. 10,5 t dimensions of the machine ca. 2,71 x 2,43 x 2,40 m MAPPS control system Renishaw HPRA (manual tool presetter) Blum Laser Control Direct measuring system X;Y;Z;B Collet chuck SMW Autoblok KSZ-MB-040-Z140 Workpiece conveyor belt Bar feeder Breuning Irco ILS-RBK-10012 Knoll band filter KF10/500 / IKZ with milling spindle 7 stages up to 70 bar Chip conveyor ConSep 2000

Condition: used, Year of construction: 1996, functionality: limited functionality, travel distance X-axis: 630 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 650 mm, controller model: Fanuc MSX-516, rotational speed (max.): 12,000 rpm, The P8 power supply, valued at €1,500, was only replaced in August 2024! The spindle was repaired in 2017 and has mostly only been used for single-layer operation since then! TECHNICAL DETAILS Travel range X-axis: 630 mm Travel range Y-axis: 600 mm Travel range Z-axis: 650 mm Feed length X-axis: 630 mm Feed length Y-axis: 600 mm Feed length Z-axis: 650 mm Table width: 500 mm Table length: 500 mm Number of pallets: 2 Maximum speed: 12,000 rpm Number of tool magazine slots: 60 (BT40) MACHINE DETAILS Control: Fanuc MSX-516 Phases: 3 Frequency: 50 Hz Voltage: AC 200 V Full load current: 181 A Note: The rapid traverse rate of the X-axis is reduced by 20% to extend the service life of the telescopic guides. The sealing ring during pallet changes is likely defective. The seller temporarily resolved this by inserting a ball valve in between when the pallets needed to be changed. Dodjzcuyijpfx Am Tokp EQUIPMENT Documentation/Manual Chip conveyor

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, X-axis travel: 140 mm Y-axis travel: +/- 40 mm Z-axis travel (1+2): 450 / 410 mm Turning length: 750 mm Turning diameter over cross slide: 250 mm Turning diameter: 190 mm Distance between centres: 750 mm Max. bar diameter: 52 mm Spindle speed (max.): 4,000 rpm Main spindle speed range: 60 - 6,000 rpm Drive power - main spindle: 22 / 18.5 kW Max. torque: 198 Nm Counter spindle B-axis travel: 525 mm Feeds Feed rate X (1+2): 18,000 mm/min Feed rate Y: 6,000 mm/min Feed rate Z (1+2): 24,000 mm/min Feed rate B: 24,000 mm/min Number of turrets: 2 Number of tool stations: 2x 16 pos. Shank height for square tool: 20 mm Shank diameter for drills: 25 mm Turret indexing time: 0.2 s Tool holder: VDI 30 Speed range - driven tool stations (max.): 6,000 rpm Drive power - driven tool stations: 5.5 / 3.7 / 2.2 kW Rapid traverse X (1+2): 18 m/min Rapid traverse Y: 6 m/min Rapid traverse Z (1+2): 24 m/min Rapid traverse B: 24 m/min Djdpfx Asyyupmjm Tskp Rapid traverse C: 400 rpm MACHINE DETAILS Control: MSX 501 Fanuc drives Machine is in excellent condition

Condition: good (used), Year of construction: 2006, functionality: fully functional, Technical details turning diameter 660/275 mm turning length 1498 mm control Fanuc/Mori Seiki MSX 701 total power requirement 90 kVA weight of the machine ca. 26,6 t dimensions of the machine ca. 5301 x 2997 x 2788 mm Additional information 9-axis CNC turning and milling centre * Fanuc MSX-701 CNC control * Milling spindle at top (B axis), as full 4th axis, positioning 0.0001 deg. * 40-position tool magazine * 10-position turret at bottom, all positions driven * 2 x 3-jaw quick-change chuck KNCS-N 315/91 * KNOLL high-pressure coolant system, pressure setting 12/25/35/45/55/62 and 72 bar, with maintenance-free rotary filter system * Chip conveyor * Drain system for main spindle chuck (controlled via M function) * Drain system for tool cutting edge (controlled via M function) * Coolant gun incl. accessories * Oil mist extraction * Direct measuring system X1, X2, Y-axis * Bar loader interface * Double foot switch for both spindles * Islands and pocket programming for MAPPS * High-speed fixed cycle for MAPPS * Programm memory extension to 8 MB * Programm restart * 3-stage signal lamp * 512 MB memory card (CF card) Swing diameter over cross slide (tool spindle 1): 750 mm Swing diameter over cross slide (turret 2): 400 mm Max. turning diameter (tool spindle 1): 660 mm Max. turning diameter (turret 2): 275 mm Max. machined workpiece length: 1498 mm Max. bar material: 90 mm Travels: X1 axis (tool spindle): 750 mm Y axis (tool spindle): 420 (+/- 210) mm Z1 axis (tool spindle): 1635 + 100 mm for tool change B axis (tool spindle): +/- 120 deg., full B-axis 1 deg. indexed and 0.0001 deg. braked X2 axis (turret): 195 mm Z2 axis (turret): 1525 mm SZ axis (subspindle): 1610 mm Rapid traverse: (X1,Z1) 50 m/min. / (Y,X2,Z2,SZ) 30 m/min. Main and subspindle: Spindle speeds infinitely variable (spindle 1 + 2): 30-3000 rpm. C axis (spindle 1 + 2): 0.001 deg. Main spindle motor: 22/18.5 kW Subspindle motor: 22/18.5 kW Torque (spindle 1 + 2): 1000 Nm Disc turret: Number of tool positions: 10 Speed of driven tools: 6000 rpm. Drive power: 5.5/3.7 kW Milling spindle head: Tool holder: HSK A63 Max. speed: 12,000 rpm Drive power: 18.5/11 kW Torque: 120/44 Nm Tool changer: 40-stations Tool diameter 70/140 mm Tool length 400 mm Tool weight 8/10 kg Total power requirement 90 kVA Main dimensions Length x width x height 5301 x 2997 x 2788 mm Machine weight 26.6 t Accessories: Measuring arm (picture) tool measurement in machine Tool holder + box, reduction sleeves, driven tools Dkjdpfx Amjzablto Tep Clamping jaws package Collets package

Condition: ready for operation (used), Year of construction: 1998, travel distance X-axis: 600 mm, travel distance Y-axis: 430 mm, travel distance Z-axis: 460 mm, total height: 2,770 mm, table load: 500 kg, overall weight: 5,200 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 22,000 W, number of slots in tool magazine: 30, tool weight: 8,000 g, number of axes: 4, This 4-axis MORI SEIKI SV-400 was manufactured in 1998. It features a table size of 900 × 500 mm and impressive travels of 600 mm in the X-axis, 430 mm in the Y-axis, and 460 mm in the Z-axis. The machine includes a maximum spindle speed of 12,000 rpm and a tool magazine capacity of 30 stations. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI SV-400 vertical machining centre we have for sale. Contact us for further details. Dsdpsy Uxigjfx Am Tokp • Table: 900 × 500 mm; 4 T-slots (18 mm width × 100 mm pitch) • Number of axes: 4 (X, Y, Z + 4th rotary axis; 4th axis supplied by accessory listed below) • Distance spindle nose to table: 150–610 mm • Spindle: max; 22 / 18.5 kW motor; 85 mm front bearing ID • Tool magazine: max tool Ø 80 mm (adjacent) / 125 mm (non-adjacent); max tool length 300 mm; chip-to-chip 3.2 s • Feedrates: Rapid X/Y/Z 32,000 mm/min; max working feed 16,000 mm/min • Axis motor power: X/Y 2.1 kW; Z 4.4 kW • CNC control: MORI-FANUC MSC-501 (compatible with MSC-518); memory 320 m; functions include helical interpolation and cutting force control (Power Monitor) • Coolant system: 50 bar high-pressure through-spindle coolant (TSC) • Features: air blow for part cleaning, full enclosure, end-of-cycle lamp, RS-232 interface • Floor space: 2,200 × 2,550 mm • Electrical: total installed power 50.2 kVA; 380 V, 50 Hz Additional equipment • 4th axis attachment: Tsudakoma RN-150R rotary table with 200 mm faceplate and tailstock • Chip management: 2× rear-discharge chip conveyors Technical Specification Taper Size BT 40

Condition: ready for operation (used), Year of construction: 2006, This 4-axis MORI SEIKI NV-5000α1/40 was manufactured in 2006. It features an X-axis travel of 800 mm, Y-axis travel of 510 mm, and Z-axis travel of 510 mm. The machine includes a robust table size of 1,100 × 600 mm with a maximum table load capacity of 1,000 kg. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI NV-5000α1/40 vertical machining centre we have for sale. Contact us for further details. Djdpfoy Uxaxox Am Tskp

Condition: ready for operation (used), Year of construction: 2010, travel distance X-axis: 560 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 630 mm, table load: 400 kg, spindle speed (max.): 14,000 rpm, number of slots in tool magazine: 60, number of axes: 4, This 4-axis MORI SEIKI NH 4000 DCG was manufactured in 2010. It features an X-axis travel of 560 mm, Y-axis travel of 560 mm, and Z-axis travel of 630 mm. The machine has a spindle speed of 14,000 rpm and a tool magazine capacity of 60 positions. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI NH 4000 DCG horizontal machining centre we have for sale. Contact us for further details. • B-axis: Continuous Additional equipment • Pallet cubes: 250 × 250 × 600 mm and 400 × 150 × 600 mm Dkjdey Uw I Ispfx Am Tep • Various tooling • D'Andrea boring head attachment • Full machine manuals • SEI filtration/extraction unit • KUBE mist collector system Technical Specification Taper Size BT 40

Condition: used, Year of construction: 1995, Fanuc MSC 516 2 pallets, 500x500mm BT40 spindle Spindle speed: 12,000 RPM 20-tool changer Djdozgrzkopfx Am Tokp Coolant pressure: 20 bar Renishaw

Condition: excellent (used), Year of construction: 2005, x-travel 630 mm y-travel 600 mm z-travel 670 mm Control MSX 501 spindle turning speed - stepless 14000 U/min tool taper BT 40 pallet chang. with pallet turn. 360x1 degree 2 max. workpiece weight 500 kg tool change unit 60 fach table-size 500 x 500 mm total power requirement 56 kW Dksdpfxeygx D Te Am Tep weight of the machine ca. 11,8 t dimensions of the machine ca. 5,8 x 3,6 x 3,0 m

Year of construction: 2000, condition: as good as new (ex-display), The following spare parts are available from a MORI SEIKI VL250, year of manufacture 2000: 1. Turret (not complete) Ball screw with nut, X and Z axis X and Z axis guide parts are from a new machine Motor, X-axis See photos. Djdpfocbinnsx Am Tokp

Condition: used, Year of construction: 1990, Technical details: x-travel: 800 mm y-travel: 410 mm z-travel: 510 mm control: Fanuc 10 MA rapid travel x/y/z: 20/20/15 mm/min table surface area: 1100 x 450 mm tool taper: BT 40 tool magazin:: 30 BT 40 max. tool length: 250 mm max. tool weight: 8 kg power requirement: 7,5/5,5 kW turning speed range: 6000 1/min weight of the machine ca.: 6,3 t Dedpoy S T T Uofx Am Tjkp Under offer is a complete CNC tool shop, whioch will be given up due to old age of owner. The Mori Seiki is still highly accurate. All existing tool holders, tools, drills, etc. come with the machine. All measuring devices also come with the machine. Upon request orders for parts to be made can be passed on to new owner. This is a low cost all inclusive opportunity for a "Startup" *

Condition: used, Year of construction: 2013, x-travel 600 mm y-travel 530 mm Djdpex R Enbofx Am Tokp z-travel 510 mm Control M 730 BM MAPPS IV max. spindle speed 10.000 min/-1 power capacity - main spindel 15 / 11 kW tool taper SK 40 transmission ratio 1 spindle diameter in front bearing 80 mm table surface area 900 x 600 mm max. table load 800 kg T-slots 6x 18 x 100 mm distance spindle /table 150 - 660 mm number of toolpositions 30 pos. tool taper SK 40 max. tool diameter 80 mm max. tool-dia with free toolbox 150 mm max. tool length 300 mm max. tool weight 8,0 kg change-time tool to tool ca. 1,3 sec change-time chip to chip ca. 3,45 sec rapid traverse ( X / Y / Z ) 30 m/min feed speeds 1 - 30.000 mm/min Tipp feed 0 - 5.000 : 20 mm/min total power requirement 30 kVA weight of the machine ca. 6,0 t dimensions of the machine ca. 4,5 x 3,5 x 2,7 m CNC - Machining Center Vertical MORI SEIKI - NVX 5060 II / 40

Condition: used, Year of construction: 2011, turning diameter max. 320 mm turning length max. 810 mm control MSX-701 IV greates pass round over bed 800 mm Swing dia. over traverse guideway 800 mm distance between spindles 1.130 mm Number of revolutions max. 5.000 rpm power capacity - main spindel 25 / 22 kW max. Torque 358 Nm spindle diameter in front bearing 120 mm spindle bore 73 mm max. usable bar diameter 65 mm C-Axis 0,001 ° spindle nose JIS A2-6 collet chuck 160 mm Number of revolutions max. 5.000 rpm power capacity - Sub spindle 25 / 22 kW max. Torque 358 Nm spindle diameter in front bearing 120 mm spindle bore 73 mm max. usable bar diameter 65 mm C-Axis 0,001 ° spindle nose JIS A2-6 collet chuck 160 mm number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Dsdpfxsv E R E Ne Am Tekp Y - Axis 110 mm Shank diameter 20 x 20 mm Drill shank diameter 32 mm turret change time 0,18 sec. number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Shank diameter 20 x 20 mm Drill shank diameter 32 mm turret change time 0,18 sec. x-travel 1/2: 210 mm y-travel 110 mm z-travel 1/2: 810 mm Traverses Subspindle B: 870 mm rapid traverse ( X / Y / Z ) 1: 30 / 20 / 50 m/min rapid traverse ( X / Y / Z ) 2: 30 / - / 50 m/min Tipp feed 0 - 5.000 mm/min total power requirement 94 kVA weight of the machine ca. 8,3 t dimensions of the machine ca. 10,0 x 3,0 x 2,5 m CNC - Turning- and MillingCenter MORI SEIKI - NZ 2000 T2Y - Main- and Subspindle - 2 turrets, up and below - Y-Axis - 2x 16 driven tool positions

Condition: used, Year of construction: 2008, turning diameter max. 320 mm turning length 810 mm control MSX 701 MAPPS III standard turning dia. 200 mm Main spindle: Number of revolutions max. 6.000 min/-1 Djdpfx Astqmqwem Tekp power capacity - main spindel 22 / 18,5 kW Bar feed max. 52 mm spindle bore 61 mm C-Axis 0,001 ° Subspindel: Number of revolutions max. 6.000 min/-1 power capacity - Sub spindle 22 / 18,5 kW Bar feed max. 52 mm spindle bore 61 mm C-Axis 0,001 ° Turret 1 + 3: number of toolpositions je 16 pos. Number of driven toolspositions je 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 (+65 / -45) mm Turret 2: number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 (+45 / -65) mm axis stroke: x-travel 1-3: 210 mm y-travel 1-3: 110 mm z-travel 1+3: 300 / 2: 810 mm total power requirement 90 kVA weight of the machine ca. 9,3 t dimensions of the machine ca. 4,5 x 3,0 x 2,5 m CNC - Turning- and MillingCenter MORI SEIKI - NZ 1500 T3Y3 - Main- and Subspindle - 3 turrets, 2x upper / 1x below - 3x Y-Axis - 3x 16-pos. tool-drive - incl. 28x collets - incl. Hainbuch changing device

Condition: used, Year of construction: 2002, turning diameter 390 mm turning length 507 mm control MSG 805 MAPPS max. turning diameter 390 mm greates pass round over bed 680 mm Swing dia. over traverse guideway 510 mm Dedpfjvzhiqsx Am Tskp centre distance 618 mm turning speed range - main spindle 45 - 4.500 min/-1 power capacity - main spindel 11 / 7,5 kW spindle bearing diameter 110 mm spindle bore 73 mm max. bar capacity 51 mm spindle nose JIS A2-6 chucking diameter 210 mm C-Axis 0,001 ° x-axis 235 (195+40) mm z-axis 520 mm number of toolpositions 12 pos. Number of driven toolspositions 12 pos. Spindle speed - driven tool stations max. 3.000 min -1 power capacity driven tool-stations 5,9 / 4,5 kW Shank height for square tool 25 mm Drill shank diameter max. 50 mm turret change time 0,2 sec. tailstock adjustment 490 mm dia. of quill 85 mm taper of center MT 4 quill stroke 120 mm rapid traverse X: 18 / Z: 24 m/min Tipp feed 0 - 1.260 mm/min total power requirement 30,1 kW weight of the machine ca. 4,5 t dimensions of the machine ca. 5,0 x 2,5 x 2,5 m CNC - Turning- and Millingcenter MORI SEIKI - SL 204 MC

Condition: used, Year of construction: 2007, x-travel 560 mm y-travel 560 mm z-travel 630 mm Control MSX 701 III MAPPS Max. rpm 14.000 min/-1 power capacity - main spindel 18,5 / 11 kW max. Torque 120 Nm tool taper MAS BT 40 distance spindle center to table 80 - 640 mm distance Spindlenose and center of table 100 - 730 mm numbers of pallets 2 size of pallet 400 x 400 mm max. workpiece weight 400 kg max. workpiecediameter 630 mm max. workpiece height 900 mm change time of pallets 6,0 sec b - axis 0,001 ° number of toolpositions 60 pos. tool taper MAS BT 40 max. tool diameter 70 / (140) mm max. tool length 400 mm max. tool weight 8,0 kg rapid traverse ( X / Y / Z ) 50 m/min feed speeds 0 - 50.000 mm/min Tipp feed 0 - 1.260 mm/min total power requirement 35 kVA weight of the machine ca. 9,8 t dimensions of the machine ca. 5,5 x 3,5 x 2,8 m CNC - Machiningcenter Horizontal MORI SEIKI - NH 4000 DCG - pallet-changer - Control options Dodpfx Aewbi Adjm Tjkp Program restart, cylindrical and spiral interpolation High-speed milling cycles, island and pocket milling cycles

Condition: used, Year of construction: 2010, turning diameter max. 320 mm turning length 810 mm control MSX 701 Number of revolutions max. 6.000 U/min power capacity - main spindel 22 / 18 kW max. usable bar diameter 52 mm C-Axis 0,001 ° spindle nose JIS A2-5 collet chuck 140 mm Number of revolutions max. 6.000 U/min power capacity - Sub spindle 22 / 18 kW max. usable bar diameter 52 mm C-Axis 0,001 ° spindle nose JIS A2-5 collet chuck 140 mm number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 mm number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 Dkedpfjv E R E Aox Am Tep power capacity - driven tools 7,5 / 5,5 kW x-travel 1/2: 210 mm y-travel 110 mm z-travel 1/2: 810 mm b-axis 900 mm total power requirement 86 kVA weight of the machine ca. 8,1 t dimensions of the machine ca. 8,0 x 3,5 x 2,8 m CNC - Turning- and MillingCenter MORI SEIKI - NZ 1500 T2Y - Main- and Subspindle - 2 turrets, up and below - Y-Axis - 2x 16 driven tool positions

Condition: refurbished (used), Year of construction: 1996, functionality: fully functional, travel distance X-axis: 420 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 250 mm, rapid traverse X-axis: 48,000 m/min, rapid traverse Y-axis: 48,000 m/min, rapid traverse Z-axis: 48,000 m/min, controller model: Mitsubishi Meldas MSC-802M, The MORI SEIKI TV-30 is a compact and precise vertical machining center, designed for drilling, tapping, and milling operations on small components. Manufactured in 1996, it is equipped with a Mitsubishi Meldas MSC-802M control and features characteristics ideal for high-speed light machining work, with an automatic tool changer and a well-sized table relative to its compact footprint. General Technical Data Brand: MORI SEIKI Model: TV-30 Category: Vertical Machining Centers Year of manufacture: 08-1996 CNC Control: Mitsubishi Meldas MSC-802M Machine weight: 2 tons Dksdpfx Amoxfaw Dj Tep Machine Dimensions: Length: 1,200 mm Width: 1,720 mm Height: 2,260 mm Spindle Spindle speed: 8,000 rpm Spindle motor power (cont./30 min): - 3.7 / 2.2 kW (continuous) - 5.5 / 3.7 kW (30 min) Machining Capacity X-Axis travel: 420 mm Y-Axis travel: 300 mm + 60 mm Z-Axis travel: 250 mm Maximum drilling diameter: 13 mm Maximum tapping diameter: M12 Table Table size: 600 x 340 mm Table load capacity: 150 kg Feed Rates Rapid traverse X / Y / Z axes: 48,000 mm/min Working feedrates X / Y / Z in linear interpolation (max): 12,000 mm/min Manual feedrates: 0 – 1,260 mm/min Tool Changer Tool taper: BT-30 Shank: MAS-P30T-1 45° Tool magazine capacity: 10 stations Max. diameter of adjacent tools: Ø 80 mm Max. tool length: 200 mm Max. tool weight: 3 kg Other Equipment Manuals, Electrical Schematics and CE Declaration 100-liter coolant tank with pump Transformer

Condition: used, Year of construction: 2006, x-travel 600 mm y-travel 400 mm z-travel 400 mm control MSX 501 Mori Seiki table surface area 700 x 450 mm max. table load 350 kg number of T-slots 4 T-slot - width 18 mm T-slot - distance 100 mm Number of revolutions 12.000 U/min power capacity - main spindel 18,5 / 15 / 11 kW tool taper BT 40 max. Torque 110,5 Nm diameter of forward milling spindle bearing 70 rapid travel x/y/z 20.000 mm/min feed speeds 1 - 20.000 mm/min Tipp feed 15 Steps / 0 - 1.260 mm/min Number of Toolpositions in magazine 40 Pos. Max. mould width 80 mm max. tool-dia with free toolbox 125 mm Dedpfsv Az Ucex Am Tokp max. tool length 250 mm max. tool weight 8 kg change-time chip to chip 2,8 sec change-time tool to tool 1,0 sec total power requirement 34 kVA weight of the machine ca. 7,2 t dimensions of the machine ca. 2,8 x 3,0 x 2,9 m Machining Center Vertical MORI SEIKI - NV 4000 DCG - ca. 14.000 Operating-Hours

Condition: used, Year of construction: 1998, x-travel 1.020 mm y-travel 510 mm z-travel 510 mm control MSC 501 Fanuc table surface area (APC) 1.200 x 480 mm max. table load (APC) 550 kg turning speed range - milling 10.000 U/min power capacity - milling spindle 22 / 18,5 kW tool taper BT 40 number of toolpositions 30 pos. tool taper BT 40 max. tool diameter 80 mm max. tool-dia with free toolbox 125 mm max. tool length 300 mm max. tool weight 8 kg rapid traverse 32 m/min feed 1 ~ 16.000 mm/min Tipp feed 0 ~ 1.260 mm/min spindle bearing diameter 85 mm total power requirement 59,5 kVA weight of the machine ca. 6,9 t dimensions of the machine ca. 3,9 x 2,7 x 2,9 m CNC - Machining Center - Vertical MORI SEIKI - SV 500 B/40 - Clamping devices are NOT included in the scope of delivery Dodpfx Ajy Apcyom Tokp

Condition: used, Year of construction: 1998, functionality: fully functional, machine/vehicle number: 901, type of input current: three-phase, bar diameter (max.): 40 mm, collet bore: 42 mm, We are offering this used Mori Seiki SL-150S/500 CNC lathe with sub-spindle, manufactured in 1998. Dedjzdd Dyepfx Am Tokp Manufacturer: Mori Seiki Model: SL-150S/500 Serial number: 901 Phases: 3 Rated power: 32 kVA Date of manufacture: 9/1998 Includes LNS Quick Load Servo 65 bar feeder (manufactured in 2007). Includes reducing sleeves. Includes Hainbuch collet chuck system (main and sub spindles have the same collet size for Hainbuch BZI 42). Includes 120x collet. Includes clamping blocks for the turret. Excludes tooling. The machine is currently still in production and needs to be replaced with a new one. The machine has been well maintained. Please note that this is a machine without powered tools! If you have any questions or would like more information, please feel free to send us a message.

Condition: ready for operation (used), Year of construction: 1998, - USED - 4-AXIS HORIZONTAL MACHINING CENTRE WITH PALLET CHANGER X-AXIS TRAVEL: 2000 mm Y-AXIS TRAVEL: 1300 mm Z-AXIS TRAVEL: 1200 mm SPINDLE: 60-6000 rpm; 30-37 kW; ISO 50 - BT PALLET: N.2 ; 1000X1000 mm MAX ADMITTED LOAD: 3000 Kg TOOL MAGAZINE: CHAIN-TYPE ; 120 POS CONTROL UNIT: MSC 502 WEIGHT: 35200 Kg Djdpfx Amsyvlx Ds Tokp OVERALL DIMENSIONS: 5330 x 7720 x 3810 mm ACCESSORIES: HIGH PRESSURE COOLANT ; SWARF CONVEYOR ; RS 232 SERIAL PORT ; TOOL SETTER NOTE: MAX PIECE DIAMETER 2000 mm; MAX HEIGHT 1550 mm; MAX WEIGTH 3000 Kg

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: NL251GL3750, CNC turning and milling center DMG MORI NL2500SY/700 Serial number: NL251GL3750 Available from location: Machine type: CNC turning and milling center Manufacturer: MORI SEIKI Type: NL 2500 Y / 1250 Year of manufacture: 2006 Control system: MSX 850 III MAPPS Country of origin: Japan Delivery time: upon agreement Incoterm: EXW (Ex Works) Additional information: CNC turning and milling center MORI SEIKI - NL 2500 Y / 1250 Technical details Turning diameter: 275 mm Turning length: 1,298 mm Control system: MSX 850 III MAPPS Swinging diameter over bed: 923.8 mm Swinging diameter over cross slide: 755 mm Max. turning diameter: 356 mm Max. bar diameter: 80 mm Main spindle: Speed range - main spindle: 4,000 rpm Drive power - main spindle: 18.5 / 15 kW Spindle nose: JIS A2-8 Spindle bore: 91 mm Spindle bearing diameter: 140 mm C-axis: Travel: X-axis: 260 mm Z-axis: 1,345 mm Y-axis: Turret: Tool positions: 12 Height for square tools: 25 mm Shank diameter for drill rods: max. 50 mm Turret indexing time: 0.25 sec. Speed range of driven tools: 6,000 rpm Drive power - driven tools: 5.5 / 3.7 kW Dodszcn Hvopfx Am Tskp Feed rate: Rapid traverse X-axis: 30 m/min Rapid traverse Z-axis: 30 m/min Rapid traverse Y-axis: 10 m/min Tailstock: Tailstock travel: 1,284 mm Tailstock spindle diameter: 110 mm Taper: MT 5 Rapid traverse: 7 m/min Total power requirement: 38 kVA Machine weight approx.: 7.5 t Space requirement approx.: 5.5 x 3.4 x 2.3 m Accessories: Documentation: Chip conveyor: Hydraulic unit: Coolant system: High-pressure coolant: 3-jaw chuck: Errors and omissions in technical data are reserved. The scope of the accessories is exclusive and limited to the description of the items in the text. No claim is made for any further accessories depicted in the images, for example for illustrative purposes.

Condition: good (used), Year of construction: 2006, operating hours: 14,119 h, functionality: fully functional, machine/vehicle number: 6682NL151EG0306J, turning diameter: 260 mm, spindle speed (max.): 6,000 rpm, total height: 2,000 mm, total length: 2,185 mm, total width: 2,460 mm, bar diameter (max.): 45 mm, overall weight: 5,300 kg, Machine type: CNC lathe Manufacturer: DMG Mori Model: NL1500/500 Year of manufacture: 2006 Dkodpfx Ameyxnu Ho Tjp Operating hours: 14,119h (as of 17.12.2025) Control: MSX-850 BM Spindle speed: 6,000 rpm Machining diameter: with bar loader Ø16-45mm Tool stations: 12 plus tailstock Weight: 5,300kg Dimensions (W×D×H): 2460×2000×2185mm Transport, collection, and dismantling must be organized by the buyer.

Condition: ready for operation (used), Year of construction: 1989, functionality: fully functional, machine/vehicle number: 1764, controller manufacturer: Fanuc, No minimum price – guaranteed sale to the highest bidder! MACHINE DETAILS Dkodpfxey Sluqe Am Tjp Control: Fanuc EQUIPMENT Accessories as shown in the pictures