Used Moulding for sale (1,523)

Year of construction: 1999, condition: used, Clamping force: 8,000kN, operating voltage: 400V, mains frequency: 50Hz, power supply: three-phase AC, 3 phases, total rated current: 400A, max. motor current: 205A, upstream fuse protection: 2x200A, an on-site inspection is possible. Rcsdpfxo Ad Nn Ho Airoh

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Rcodpsg Ailcefx Aireh Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: used, Year of construction: 1996, functionality: fully functional, High-performance planing and profiling machines / four-sided planer Manufacturer: Weinig Model: Hydromat 30 / H 30 N System originates from a parquet factory Planing width: approx. 220 mm Planing height: approx. 120 mm Spindle arrangement: Bottom (joiner), 22 kW Right, 7.5 kW Left, 18 kW Top, 30 kW Spindle diameter: 50 mm Rcedpfsz D Exbjx Airoh Feed speed adjustable, 12 – 120 m/min. Voltage: 380 V, 50 Hz

Year of construction: 2014, condition: ready for operation (used), An ENGEL injection molding machine is offered. Clamping force: 1800kN, opening force: 96kN, max. opening stroke: 750mm, min. mold height: 300mm, max. platen distance: 1050mm, clear tie-bar spacing: tie-bar-less, mold mounting platens X/Y: 880mm/830mm, max. mold weight: 1500kg at center of gravity 230mm, ejector stroke: 180mm, ejector force forward/backward: 80kN/33kN, screw diameter: 55mm, metering stroke: 215mm, max. stroke volume: 510cm³, injection rate: 255cm³/s, max. injection pressure: 2050bar, nozzle stroke: 350mm, nozzle contact force: 67kN, injection unit heating capacity: 16.3kW, heating zones incl. nozzle: 5, barrel: M9 bimetallic barrel, integrated hot runner control zones: 24×220V, mold cooling circuits: 6×10l/min, hydraulic oil capacity: approx. 540l, operating hours: 67423h (as of 30.06.2026). The machine will be available from December. Machine dimensions X/Y/Z: approx. 6275mm/1888mm/2100mm, weight without mold: approx. 12200kg. Documentation available. An on-site inspection is possible. Rcsdpfxezt Slpo Airoh

Condition: excellent (used), Profiles / mouldings wrapping line Composed by: a) “DOUCET” loading-infeeding system, Model MSP-APV-408 b) “SCM” moulding machine, model SuperSet XL c) “BARBERAN” wrapping machine, model PUR-31-LD Rodpfxezxraks Airech d) “NORDSON” PU glue melter-dispenser, model VersaBlue

Condition: excellent (used), Year of construction: 2001, operating hours: 9,089 h, functionality: fully functional, machine/vehicle number: 94250, WEINIG HYDROMAT H23 ELECTRONIC FEED FREQUENCY CONTROLLED (8 – 60 M/MIN). FEED MOTOR 15 KW Rcedpfx Asz Eznuoireh 50MM SPINDLES WORKING WIDTH MAX. 230 MM WORKING HEIGHT MAX. 160 MM SHORT INFEED WITH (GROOVED FEED GUIDANCE, SEE USES AND BENEFITS HIGHLIGHTED BELOW) BOTTOM 7.5KW 6,000 RPM RIGHT 7.5KW 6,000 RPM LEFT 7.5KW 6,000 RPM JOINTER READY RIGHT 7.5KW 6,000 RPM LEFT 7.5KW 6,000 RPM JOINTER READY TOP 11KW 6,000 RPM OUTBOARD BEARING, JOINTER READY BOTTOM 7.5KW 6,000 RPM OUTBOARD BEARING, JOINTER READY TOP 7.5KW 6,000 RPM OUTBOARD BEARING, JOINTER READY BOTTOM 11 KW 6,000 RPM OUTBOARD BEARING, JOINTER READY 12X TOP FEED ROLLERS 6X BOTTOM FEED ROLLERS CNC ADJUSMENT OF 1ST BEDPLATE FROM CONTROL PANEL POSSIBLE TO ADD ADDITIONAL STRAIGHT / PROFILE JOINTERS AS NEEDED FULL SOUND ENCLOSURE AUTOMATIC LUBRICATION SYSTEM FULL DOCUMENTATION INCLUDED EXHAUST MANIFOLD INCLUDED MACHINE LENGTH 5.2M POSSIBLE TO OFFER MECHANISATION IF NEEDED POSSIBLE TO OFFER MECHANISATION SPECIFICALLY FOR SHORT LENGTH FEEDING AND STACKING IF NEEDED Grooved Feed Guidance, Core Functions & Benefits: The longitudinal grooves milled directly into the bedplates work in conjunction with custom bottom cutterhead knives or grooving cutters. The initial cutter cuts matching grooves into the underside of the raw stock, registering it securely to the bed's grooves to keep short or cupped boards running straight without drifting off the fence. Friction & Resin Relief: Standard flat bedplates create significant surface drag when feeding wet, sap-rich, or resinous timber (like pine, fir, or green hardwood). The channels reduce overall contact area, lowering friction and preventing suction/sticking. Debris & Pitch Clearance: Sawdust, wood resin, and pitch buildup can cause uneven heights or feeding jams. Grooves act as evacuation paths, allowing fine dust and pitch to fall away from the main bearing surface. Wax/Lubricant Distribution: When paired with an automatic or manual bed lubrication system (such as table lubrication pumps), the grooves help distribute wax/oil evenly across the table rather than letting it wipe away on the first board. Common Applications Short Stock Processing: Ideal for running short pieces (such as parquet components, drawer sides, or short moulding blanks) that would otherwise struggle to maintain parallel alignment against the side fence. Cupped or Unseasoned Wood: Prevents cupped or warped boards from rolling or twisting as they hit the vertical and horizontal cutter spindles. High-Speed Feed Lines: Reduces the strain on feed rollers and drive systems by lowering bed drag during continuous industrial runs.

Condition: used, Year of construction: 2003, functionality: fully functional, working width: 230 mm, planing height: 120 mm, planing width: 230 mm, overall weight: 3,000 kg, number of spindles: 5, Planing and Moulding Machine / Four-Sided Planer Manufacturer: SCM Model: Superset XL Year of manufacture: 2003 Rcedpfx Aioz N Amzsreh Planing machine with 5 spindles (bottom-right-left-top-universal), previously used in a parquet production facility. Working width: 230 mm Working height: 120 mm Feed speed steplessly adjustable, approx. 5 - 25 m/min. Spindle arrangement: Bottom Right Left Top Universal spindle Weight approx. 3000 kg

Condition: good (used), Year of construction: 1989, functionality: unexamined, working width: 220 mm, planing height: 120 mm, spindle diameter: 50 mm, planing width: 220 mm, working height: 120 mm, overall weight: 7,500 kg, spindle speed (max.): 6,000 rpm, spindle speed (min.): 6,000 rpm, height adjustment type: electric, type of input current: three-phase, number of spindles: 10, power: 105 kW (142.76 HP), input frequency: 50 Hz, Equipment: cabin, motor brake, Weinig Hydromat 22 B With grooved bed 10 spindles, Working width: 220 mm, working height: 120 mm, spindle diameter: 50 mm, Feed rate: 7.5 kW / 8- 40 m/min, Spindle arrangement: 1-bottom (7.5 kW) - with hydraulic clamping 2- Right (7.5 kW) 3-Left (11 kW) 4-Right (7.5 kW)- with straight jointer Rcsdpfxsu Udd So Airoh 5-Left (7.5 kW) 6-Top (15 kW) - with hydraulic clamping 7-Bottom (7.5 kW) - with hydraulic clamping 8-Top (7.5 kW) - with hydraulic clamping and straight jointer 9-bottom (7.5 kW) - with hydraulic clamping and straight jointer 10-Uni (7.5) 6 driven rollers in the table

Year of construction: 2009, condition: ready for operation (used), Clamping force: 3000kN, locking force: 3300kN, max. opening stroke: 670mm, min. mould installation height: 330mm, max. mould installation height: 710mm, max. distance between mould platens: 1380mm, mould platen dimensions: 1040x950mm, distance between tie bars: 720x650mm, max. mould weight: 4.7t, max. weight on moving mould platen: 2.4t, max. weight on fixed mould platen: 3.6t, ejector stroke: 200mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 50mm, L/D ratio: 20, injection pressure at 400°C: 2426bar, shot volume: 530cm³, shot weight (PS): 480g, max. metering stroke: 270mm, max. nozzle stroke: 470mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 110kN, installed barrel heating capacity: 14.8kW, material hopper capacity: 110l, oil tank capacity: 700l, electric screw drive: 38kW, electric clamping unit drive: 37kW, pump unit power: 22kW, total installed power: 112kW, continuous sound pressure level: 78dB(A), length: 6500mm, width: 2000mm, height: 2300mm, weight: 15.7t, operating hours according to PLC: 28,890h, barrel heating: 35,656h, pump: 27,922h, documentation available. An on-site inspection is possible. Rcodpfxjy Tx Rns Airoh

Condition: ready for operation (used), Year of construction: 2010, operating hours: 43,000 h, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 80 mm, Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1510 x 1370 mm Distance between tie bars (h x v) 1000 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Rcodpfjz N E Eyjx Airoh Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 95 / 48 kN Injection unit: Screw diameter 80 mm Ls/D ratio 22,5 Injection pressure 2205 bar Stroke volume 1810 ccm Shot weight (PS) 1647 gr. Injection rate 498 ccm/s Screw speed 195 1/min Plasticising rate max. 106 g/s Nozzle pressure 129 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 8,50 x 3,00 x 2,70 m Total machine weight 35000 kg Accessories: - Anti vibration pads - 10-fold water regulator - Krauss Maffei Robot LRX250 X: 900 mm Servo Y: 1000/1000 mm Servo Z: 3500 mm Servo C: 0 - 90 ° Additional Options: - 2 x core pulls on movable plate - 2 x core pulls on fix plate - Robot interface according to Euromap 67 - 6 x hydraulic sequentional valves - 12 x hotrunner controller - 1 x Air valve

Condition: ready for operation (used), Year of construction: 2010, operating hours: 55,000 h, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 90 mm, Clamping force 5000 kN Mould opening force, max. 279 kN Redpez I Dvyjfx Airoch Travel force movable platen opening 137,1 kN Travel force movable platen closing 116,8 kN Size of mould platens (h x v) 1370 x 1200 mm Distance between tie bars (h x v) 1000 x 800 mm Mould opening stroke 1170 mm Mould height min 480 mm Max. daylight 1650 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 90 mm Ls/D ratio 20 Injection pressure 1839 bar Stroke volume 2290 ccm Shot weight (PS) 2084 gr. Injection rate 604 ccm/s Screw speed 195 1/min Plasticising rate max. 134,2 g/s Nozzle pressure 129,4 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Reservoir capacity 1175 ltr. Dimensions and weights: Dimensions of the machine ca. 8,00 x 2,52 x 2,40 m Total machine weight 28800 kg Max. mould weight 7900 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pull on fix plate - 2 x core pulls on movable plate - 8 x hotrunner controller - Robot interface according to Euromap 67

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Rjdpfx Aioquuvrjroch Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar

Condition: ready for operation (used), Year of construction: 2012, operating hours: 52,000 h, functionality: fully functional, clamping force: 13,000 kN, screw diameter: 95 mm, Clamping force 13000 kN Mould opening force, max. 910 kN Travel force movable platen opening 217 kN Travel force movable platen closing 153 kN Size of mould platens (h x v) 2210 x 1910 mm Distance between tie bars (h x v) 1570 x 1270 mm Mould opening stroke 2350 mm Mould height min/max 700/1400 mm Max. daylight 3050 mm Injection unit: Screw diameter 95 mm Rcodpfjz Hngyex Aireh Ls/D ratio 23 Injection pressure 2173 bar Stroke volume 3721 ccm Shot weight (PS) 2642 gr. Injection rate 659 ccm/s Screw speed 150 1/min Plasticising rate max. 105 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 110 kW Installed heating capacity 59 kW Adjustable barrel heating zones 7 Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 13,00 x 4,00 x 3,00 m Total machine weight 64000 kg Max. mould weight 29000 kg Accessories: - Anti vibration pads - Sepro Robot 4050 S3 Trans Additional Options: - 3 x core pulls on movable plate - 3 x core pulls on fix plate - 2 x air valve - 6 x hydr. shot off nozzles - 16 x hotrunner controller - Robot interface according to Euromap 67

Condition: like new (used), Year of construction: 1998, functionality: fully functional, Swivel spindle milling machine VEMA TFMS 2-4 in very good condition, like new; the machine comes from a correctional facility and has only been idle for the past few years; it has been used very little and operated by only one person. VEMA is a company from Northern Germany; the machine's design is similar to the KÖLLE F45 or the PANHANS 240. everything functions perfectly all bearings and guides are in good condition year of manufacture 1998 the machine has the control panel on top with a milling stop that can be adjusted on one side or completely in depth; this is possible with a handwheel in each case. For complete adjustment, there is a mechanical counter; the counter can be set to zero at any point by pressing a button, allowing the stop to be adjusted quickly and very precisely. both stop jaws can also be adjusted individually; there are also 2 mechanical counters, which allow for one-sided adjustment and also enable facing operations, for example, on a gluing profile. the milling stop can be rotated on the machine table the machine has an extra-powerful motor with 7500 watts with pneumatic spindle locking the chips can be removed very well, with 2 extraction ports 120mm with a 30mm spindle that can be adjusted steplessly from -10 to 45°; the spindle is adjusted by handwheel with a mechanical counter. with right/left rotation we will personally deliver and demonstrate the machine anywhere in Germany for 220.00 euros; this means you have no risk when purchasing. Shipping to Austria and the rest of the EU is also possible upon request. with a large table opening that can be reduced by means of various rings; this means that milling cutters with a very large diameter can also be used, and you can also mill safely with small milling cutters (the rings are included, but they are not visible in the pictures). with 3000, 6000, 4500, 7500 and 9000 rpm the spindle height adjustment is also done by handwheel; here too, there is a very precise mechanical counter for reading the height. the table is made of highly ribbed cast iron Rcjdpfx Ais Afaugersh with an interchangeable spindle (a 40mm spindle can also be used) very robust and durable design; the machine was built for the most demanding milling operations and is suitable for all milling operations. optimal power transmission through belt drive with instruction manual with 3-roller feed HOLZ HER ETX the feed has right/left rotation; the feed rollers are individually mounted and all are like new; it has 8 speeds the machine table is 1020mm wide and 980mm deep + 500mm wide extensions on the left and right the machine can be used immediately 380V, 7500W Weight: approx. 1000kg with all necessary safety devices; the machine is approved by the Holz-BG (German Wood and Furniture Employers' Accident Insurance Association). the machine weighs approx. 1000kg with motor protection switch against overload professional equipment, not cheap hardware store junk optimal, simple, fast and safe handling

Condition: used, A Demag all-electric injection molding machine with Wittmann 3-axis robot and safety enclosure is offered. Clamping force: 1500kN, locking force: 1650kN, max. mold opening stroke: 495mm, min./max. mold height: 275mm/585mm, max. distance between mold platens: 1080mm, mold platens X/Y: 770mm/770mm, clear distance between tie bars X/Y: 520mm/520mm, max. mold weight: 1700kg, max. mold weight on the movable mold platen: 1150kg, ejector stroke: 125mm, ejector force: 35kN, ejector retraction force: 35kN, screw diameter: 35mm, L/D ratio: 20, max. injection pressure: 2430bar, stroke volume: 166cm³, shot weight: 146g, max. metering stroke: 173mm, max. nozzle stroke: 400mm, nozzle immersion depth: 20mm, nozzle contact force: 30kN, installed barrel heating capacity: 9.4kW, material hopper capacity: 35l, control: CDIAS, operating hours: approx. 76000h, machine weight: approx. 7400kg. Including WITTMANN 3-axis robot, year of manufacture: 2006, travel X/Y/Z: 550mm/1200mm/2000mm, robot weight: approx. 240kg as well as safety enclosure and 1x core pull preparation AS. Documentation available. An on-site inspection is possible. Rcedpfxs Aa Alwe Airoh

Condition: ready for operation (used), Year of construction: 1996, functionality: fully functional, input voltage: 380 V, input current: 25 A, input frequency: 50 Hz, Profile sander FLADDER 300/L.S.4 Rcsdpfx Asyrqzboiroh Year of manufacture: 1996

Condition: good (used), Year of construction: 1977, functionality: fully functional, Weinig Type PFA 250/85 Year of manufacture: 1977 1 U-7.5 kW 2 R-7.5 kW 3 L-11 kW Rcjdpsz I A N Eofx Airjh 4 R-5.5 kW 5 O-11 kW 6 O-7.5 kW 7 U-7.5 kW 8 Uni 7.5 kW Table: 2.5 m Spindles 6 and 7 with jointer Feed: 5.5 kW

Year of construction: 2009, condition: ready for operation (used), Clamping force: 2000kN, locking force: 2200kN, max. opening stroke: 570mm, min. mould installation height: 310mm, max. mould installation height: 660mm, max. distance between mould platens: 1230mm, mould platen dimensions: 830x830mm, distance between tie bars: 560x560mm, max. mould weight: 3.3t, max. weight on moving mould platen: 1.7t, max. weight on fixed mould platen: 2.5t, ejector stroke: 180mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 45mm, L/D ratio: 20, injection pressure at 400°C: 2402bar, shot volume: 358cm³, shot weight (PS): 330g, max. metering stroke: 225mm, max. nozzle stroke: 400mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 80kN, installed barrel heating capacity: 13kW, material hopper capacity: 70l, oil tank capacity: 500l, screw drive: 32kW, clamping unit drive: 32kW, pump unit power: 15kW, total installed power: 92kW, continuous sound pressure level: 74dB(A), length: 5700mm, width: 1700mm, height: 2200mm, weight: 11t, operating hours according to PLC: 36,734h, barrel heating: 25,665h, pump: 18,222h, documentation available. An on-site inspection is possible. A Wittmann robotic cell is also optionally available. Redpfxsy Tx Rbe Airoch

Condition: good (used), Year of construction: 2002, Plastic molds Year of manufacture approx. 2002 2x cavity Rcedpsx Hkq Hefx Aireh

Condition: ready for operation (used), Year of construction: 2007, operating hours: 65,000 h, functionality: fully functional, clamping force: 1,300 kN, screw diameter: 45 mm, injection weight: 289 g, Clamping force 1300 kN Mould opening force, max. 70 kN Size of mould platens (h x v) 745 x 770 mm Distance between tie bars (h x v) 470 x 470 mm Mould opening stroke 600 mm Mould height min 300 mm Max. daylight 900 mm Hydraulic ejector - stroke 150 mm Ejector force 23/10 kN Injection unit: Screw diameter 45 mm Ls/D ratio 22,4 Injection pressure 2336 bar Stroke volume 318 ccm Shot weight (PS) 289 gr. Injection rate 143 ccm/s Screw speed 265 1/min Plasticising rate max. 29,3 g/s Nozzle pressure 50 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 22 kW Installed heating capacity 15,5 kW Adjustable barrel heating zones 5 Oil Reservoir capacity 400 ltr. Dimensions and weights: Dimensions of the machine ca. 5,00 x 2,00 x 2,20 m Total machine weight 8000 kg Max. mould weight 1490 kg Accessories: - Anti vibration pads - 2 x 6-fold water regulator Additional Options: - 2 x Air valves - 1 x hydr. Core pull - 12 x hotrunner controller - Robot interface according to Euromap 67 Rsdpfezyrudox Airjch - Accumulator - 1 x pneum. core pull

Condition: ready for operation (used), Year of construction: 2011, Number of spindles 6 St. Working width 230 mm Working height 150 mm Length of the planing table 2000 mm Feed motor 5,5 kW Feed speed 7-36 m/min. Kuper SWT 23 XL-6 Four-Sided Planer ----- Machine fully functional tested! ... Working width min/max: 18 - 230 mm Working height min/max: 8 - 150 mm Spindle configuration: 1st Spindle - bottom ----- Power: 5.5 kW Speed: 6,200 rpm, incl. brake Spindle diameter: 40 mm Spindle length: 240 mm Pulley diameter: 160 mm Adjustment: axial and radial, manual 2nd Spindle - right ----- Power: 5.5 kW Speed: 6,200 rpm, incl. brake Spindle diameter: 40 mm Spindle length: 160 mm Pulley diameter: min. 110 mm - max. 200 mm Adjustment: axial and radial, manual, via mechanical digital display Adjustment: vertical 35 mm below Table 3rd Spindle - Left ----- Power: 7.5 kW Speed: 6,200 rpm, including brake Spindle diameter: 40 mm Spindle length: 160 mm Cutting circle diameter (125 mm): min. 110 mm - max. 200 mm Adjustment: axial and radial manual via mechanical digital display Adjustment: horizontal 18 mm to 230 mm at 125 mm diameter, vertical 35 mm below table 4th Spindle - Top ----- Power: 7.5 kW Speed: 6,200 rpm, including brake Spindle diameter: 40 mm Spindle length: 240 mm Cutting circle diameter (125 mm): min. 120 mm - max. 200 mm Adjustment: axial manual and radial electric via mechanical digital display Adjustment: vertical 8 mm to 150 mm at 125 mm diameter, axial 26 mm 5. Spindle - top ----- Power: 7.5 kW Speed: 7,200 rpm, incl. brake Spindle diameter: 40 mm Spindle length: 240 mm Cutting circle diameter 125 mm: min. 120 mm - max. 200 mm Adjustment: axial manual and radial electric according to mechanical digital display Adjustment: vertical 8 mm to 150 mm at 125 mm diameter, axial 26 mm 6. Spindle - bottom ----- Power: 7.5 kW Speed: 7,200 rpm, incl. brake Rcedpfjyyqnlex Airsh Spindle diameter: 40 mm Spindle length: 240 mm Cutting circle diameter 125 mm: min. 110 mm - max. 250 mm Adjustment: vertical manual according to mechanical digital display, axial manual Adjustment: Radial 8 to 150 mm with a 125 mm diameter Axially 35 mm Further features: ----- -Infinitely variable feed speed, 7-36 m/min, 5.5 kW motor -Electric height adjustment, 0.75 kW -Siemens touchscreen - Includes existing planer heads (Technical specifications provided by the manufacturer - no guarantee!)

Condition: used, Heavy-duty hydraulic strip or beam press, Wemhöner Type VS 4 S, for veneering strips, gluing timber or other pressing tasks. The press has four independently controllable pressing surfaces. Glue applicator also available. Rcedpfjzryzcsx Airsh Technical data: - Working length: 3,090 mm - Pressure: max. 104 t

Condition: used, Year of construction: 2004, Manufacturer: CFS Model: MLF400 Year: 2004 Condition: Used Serial number: 2279 Stock number: 3447J Belt width: 400 mm Capacity: max 50 cycles/min Hopper: 270 liters Belt speed: 1.5 - 15 m/min Power: 3 x 400V, 50Hz, 7.8kW Dimensions: 3650 x 1000 x 2600 mm Weight: 1186 kg With stick inserter SA4180-193 and a 1500 mm discharge conveyor. Includes an additional 900 mm discharge conveyor and an accessories cart. With a BVP bridge breaker in the hopper. Rcjdpfsz I Svuex Aireh

Condition: used, Year of construction: 2021, operating hours: 3,500 h, clamping force: 120 kN, displacement volume: 36 cm³, injection pressure: 2,200 bar, overall weight: 5,400 kg, screw conveyor diameter: 22 mm, terms of delivery: EXW (ex Works) delivery time: on request terms of payment: 100% prior to delivery Rsdpszhpg Tjfx Airech

Condition: used, Year of construction: 2013, Number of spindles 5 St. Working width 20 - 230 mm Working height 8 - 120 mm Length of the planing table 2500 mm Feed motor 1,1 kW Feed speed stufenlos regelbar 2-12 m/min. weight of the machine ca. 2500 kg Control MemoryPlus 1 WEINIG VARIOMAT Planing and Moulding Machine ----- Brief Summary: ----- - 5 spindles - Powerful motors - Cycle-controlled jointing - MemoryPlus control system - Option: Stähle-Hess Saturn single-piece sanding machine Technical Manufacturer's Description: ----- Working width: 20 – 230 mm Working height: 8 – 120 mm 1st Spindle: Horizontal Bottom ----- Motor with brake: 7.5 kW Diameter: 40 mm Speed: 6000 rpm Redpfx Ajy Spvfoirsch Tool cutting circle: 125 – 145 mm Axial adjustment range: 5 mm Rebating device incl. rebating cutters 2nd Spindle: Vertical Right ----- Motor with brake: 11.0 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 93 – 232 mm Minimum tool diameter at fence level: 93 mm Maximum tool diameter behind fence level: 180 mm Maximum moulding depth: 45 mm Axial adjustment range: 30 mm Insert segment incl. additional fence lip: 125 mm Insert segment incl. additional fence lip: 150 mm 3rd Spindle: Vertical Left ----- Shared motor with 1st right spindle Diameter: 40 mm Shared speed with right spindle Tool cutting circle: 93 – 232 mm Maximum moulding depth: 45 mm Minimum moulding depth at 200 mm tool cutting circle: 20 mm Axial adjustment range below table: 30 mm Insert segment: 125 mm Insert segment: 150 mm 4th Spindle: Horizontal Top ----- Motor with brake: 11.0 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 125–200 mm Maximum rebate depth: 30 mm Minimum rebate depth (for tool cutting circle up to 200 mm): 20 mm Axial adjustment travel: 30 mm 5. Horizontal Bottom Spindle ----- Motor with brake: 11.0 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 125–200 mm Maximum rebate depth: 15 mm Axial adjustment travel: 10 mm Table plates with wooden inserts for the bottom spindle Additional outfeed plate above the bottom spindle for wooden inserts Feed System ----- Frequency-controlled feed: 1.1 kW, infinitely variable (2–12 m/min) Double-pendulum roller opposite the left spindle Axial adjustment travel of feed rollers opposite the left spindle: 35 mm Durofer-coated spiked feed rollers Pneumatic pressure for feed rollers (incl. water separator) Cycle-controlled jointing to support manual jointing. The infeed roller is released once the second feed roller has engaged the workpiece. After the workpiece clears the second feed roller, the infeed roller returns to its starting position for the next workpiece. Additional Features: ----- MemorPLUS Control System Width and height adjustment via controls (Spindles 3 and 4: radial CNC-axis controlled) ----- Price for the above-mentioned machine available upon request! ----- OPTIONAL ADD-ON (at extra cost) — Stähle-Hess Saturn #7008: Machine previously used in conjunction with the Stähle-Hess Saturn Duo Single-P...