Used Rolling Punches for sale (8,542)

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 pressure force 5 ton. throat 125 mm Rsdpsik Srwjfx Ag Nep head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm weight 530 kg very good condition

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Redpfx Agouz If Ne Nop Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine Manufacturer PEE-WEE Type P 24 Q serial no. LC2403099 year of construction 2004 Rolling force max. 24 ton. Tool diameter max. 200 mm Redpfeh A S Htox Ag Nep Rolling spindle diameter 69,85 mm Tool bore diameter 70 mm (nominal diameter) Tool length, tool length max. 180 mm Workpiece diameter max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 rpm Motor power hydraulics approx. 3 kW Motor power roller drive 5.5 kW Mains connection 400 Volt, 50 Hz - Swivel roller spindle for threaded continuous rollers - Rolling spindle speed in 4 stages via gear changeover - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons good condition Grooving rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The thread length is maximum as long as the rolling tools are wide. Continuous rolling: When the thread length is greater than the rolling tool width. Through-feed tools have 3 sections - the infeed, the calibration section and the outfeed. Grooved rollers have no pitch and are swiveled with the pitch angle of the profile to be rolled. Pitch rollers differ from grooved rollers in that they have a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Condition: used, Single column eccentric press PELS - RICHTER type PEKR 125 Machine. No. 20684 Year of construction 1967 pressure force 125 ton. throat 430 mm table size 1100 x 750 mm ram area 890 x 650 mm table opening Ø 400 mm stroke adjustment 6 to 115 mm ram adjustment 100 mm installation height largest stroke top max. 450 mm Clamping spigot bore Ø 50 mm Stroke rate 60 strokes/min. Table height above floor 900 mm motor power 7,5 kW Mains connection 380 Volt, 50 Hz - Overload protection by crushing plate in ram - Compressed air clutch-brake combination DESCH - ram weight balancing cylinder - manual ram adjustment - two-hand operation - cam gear - Grease central lubrication Vögele - stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm Rodpjfim Thjfx Ag Nsp weight approx. 10 ton. good condition

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm clamping spigot bore Ø 40 mm installation height max. approx. 520 mm stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch Rjdpfxsffm Hhe Ag Nep - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm weight approx. 2,6 ton.

Condition: used, Punching tool with Linar built-in punching brackets ABS-SCHWABE type 100/160 11 pcs. punching brackets, punching unit for press brake Year of manufacture approx. 1990 Rodjdz Sp Hjpfx Ag Njp throat depth: 160 mm Punching capacity: 0.3 to 5 mm material thickness Hole diameter: 2 to 7 mm Installation height: 203 mm (only the punching bracket individually with punching tool) A ø 5 mm round punching tool is installed Punching bracket spacing: 195 mm - the tool unit was mounted on a hydraulic press brake Punching frame base plate dimensions L x W x H: 2500 x 345 x 37.5 mm Punching frame pressure plate dimensions L x W x H: 2500 x 173 x 20 mm Overall dimensionsL x W x H: 2500 x 345 x 300 Weight: 400 kg good condition

Condition: used, Writing desk, mobile desk, shelf trolley, logistics trolley, shelf trolley Transport trolleys, platform trolleys, workshop trolleys FETRA type 5834 Writing surface height: 1100 / 1190 mm Writing surface: 605 x 585 mm Redpfx Aopflp Esg Njp Shelves: 600 x 495 Load capacity per shelf: 50 kg Total load capacity: 100 kg - Rolling desk made of tubular steel and sectional steel - Screw construction, powder-coated, blue RAL 5007 - Writing surface on wooden board with stop bar, inclined approx. 10 - 2 shelves, can be screwed in variably (2 file heights possible) - 4 swivel castors (Ø 125 mm) with plastic rim and rubber coating on the running surface - 2 fixed castors with brakes Space requirement L x W x H: 600 x 600 x 1190 mm Weight: 25 kg Very good, as new condition 8 pieces available, price per piece

Condition: used, functionality: fully functional, input voltage: 400 V, total width: 1,380 mm, total length: 1,175 mm, total height: 1,760 mm, type of input current: three-phase, overall weight: 1,000 kg, Werner & Pfleiderer WP Model: Multimatic MUC 5 5-row Press pressure adjustable Flour duster belt Interchangeable chamber drums Connection: 400V, 16A CEE plug Used machine, not cleaned More bakery machines in stock! Rsdpfx Ageu T Aacs Njp

Condition: good (used), input voltage: 400 V, working width: 600 mm, total width: 3,480 mm, total length: 1,400 mm, total height: 2,640 mm, type of input current: three-phase, overall weight: 2,000 kg, König Eco Twin 800 Model: 800-DB800 K6-Schn6/B-DA Head machine for dough dividing and rounding Classic König Rex, 6-row Rodpfx Aex Ncc Teg Njp With spreading conveyor, proofing cabinet Depositing device for 60x80 trays Stainless steel version Connection: 400V, 16A CEE plug Dimensions: approx. 3480 x 1400 x 2640 mm (W x D x H) Used machine We have more bakery machines in stock!

Condition: excellent (used), functionality: fully functional, input voltage: 400 V, working width: 320 mm, total width: 2,300 mm, total length: 750 mm, total height: 1,370 mm, DGUV certified until: 03/2027, type of input current: three-phase, overall weight: 170 kg, conveyor belt width: 320 mm, year of last overhaul: 2026, Lippelt Rumo Seeding Station Moistening in water bath Single-sided or double-sided seed application possible With large seed plate, Stainless steel construction, mobile Exclusive to us: DGUV V3 tested Connection: 400V, 16A-CEE plug Dimensions: L 2300 x W 750 x H 1370 mm Used machine, cleaned & SAB inspected Redpfx Agox Ncc He Njp With warranty & spare parts service Options: Seed plate Maintenance contract Delivery service Spare parts box for added safety Training & commissioning We have other bakery machines in stock!

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, punching force: 330 t, Machine for punching, embossing, waste removal, and blank separation - as is - System equipped with a high-performance sheet feeder designed for automatic NON-STOP operation ⦁ For fully automatic punching, creasing, and embossing with or without gripper edge ⦁ For removal of internal waste as well as lateral and rear sheet edges ⦁ For stack-like delivery of punched and waste-removed sheets with attached gripper edges or ⦁ For separation of gripper edges and subsequent stack-like delivery of the remaining sheets ⦁ With a patented gripper carriage registration system for highest registration accuracy ⦁ With a pile stacker machine enabling fully automatic interleaving sheet feed as well as NON-STOP stacking and does not require modification even for the smallest job sizes (exchange table with comb structure) ⦁ Interleaving sheet magazine with electronic level monitoring, refillable during production ⦁ With Centerline equipment ⦁ With automatic pallet change device at the delivery section Specification Maximum sheet size: 760 x 1060 mm Minimum sheet size: 350 x 400 mm Maximum punching force: 3.3 MN (330 t) Speed: 9,000 sheets/hour Processable materials: Paper min. 80 g/m² Cardboard up to 2000 g/m² Corrugated board up to 3 mm (max. sheet warp 4%) Equipment: Optical sheet register (Dyset) Automatic non-stop feeder Waste removal station Blank separation station Centerline Fully automatic pallet changing device at delivery Incl. platform Rjdpfx Aeww E Nreg Nsp Quick-lock frames at all tooling stations

Condition: good (used), functionality: fully functional, mileage: 6,17,000 km, power: 302 kW (410.61 HP), first registration: 11/2011, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 6x2, wheelbase: 4,500 mm, fuel: diesel, driver cabin: day cab, gearing type: mechanical, emission class: euro5, suspension: steel-air, Year of construction: 2011, Equipment: ABS, retarder, SUPERSTRUCTURE MEILLER XR 21 Z 2011 Rodpoqaglqofx Ag Nsp Wheelbase 4,50m (Passo) Good condition!

Condition: excellent (used), functionality: fully functional, input voltage: 400 V, warranty duration: 3 months, working width: 250 mm, total width: 2,300 mm, total length: 750 mm, total height: 1,370 mm, DGUV certified until: 03/2027, type of input current: three-phase, conveyor belt width: 250 mm, year of last overhaul: 2026, Lippelt Mini Rustica Bun Production Line for all specialty buns Stainless steel construction Simple and efficient production of square dough pieces Stepless cutting length adjustment Cutting rollers newly coated Machine is mobile Robust technology DGUV V3 tested – only by us Rjdox I U H Ujpfx Ag Nop Connection: 400V, 16A-CEE plug Dimensions: L 2300 x W 750 x H 1370 mm Used machine, cleaned and SAB tested with warranty & spare parts service Options: Rumo seed dispenser Maintenance contract Service package Spare parts box Delivery service Commissioning & instruction We have more bakery machines in stock!

Condition: used, total length: 1,700 mm, total width: 820 mm, total height: 1,570 mm, Empty weight: 580 kg - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 4077950107003 - Drive system: Conventional - Drive: Hydraulic - Punching force [ton]: 38 - Round bar cutting capacity [mm]: 32 - Shearing width [mm]: 300 - Max. plate thickness shearing [mm]: 15 - Options: Length stop - Transport dimensions: 1700mm x 820mm x 1570mm (l x w x h) Rjdpfx Aoymfbfjg Nsp - Transport weight [kg]: 580kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, total length: 1,100 mm, total width: 1,670 mm, total height: 1,900 mm, Empty weight: 1.930 kg - Documentation available: No - CE certificate present: No - Serial number: 4422758897010 - Drive system: Conventional - Drive: Hydraulic - Punching force [ton]: 60 - Punch throat depth [mm]: 400 - Notching width [mm]: 70 - Max. plate thickness notching [mm]: 13 - Round bar cutting capacity [mm]: 40 - Shearing width [mm]: 400 - Max. plate thickness shearing [mm]: 20 Rsdpfeymfa Ujx Ag Nsp - Options: Length stop - Transport dimensions: 1100mm x 1670mm x 1900mm (l x w x h) - Transport weight [kg]: 1930kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: good (used), functionality: fully functional, Year of construction: 2013, laser power: 2,700 W, X working area max.: 2500 mm Y working area max.: 1250 mm Control system: Rexroth IndraMotion MTX (basic version) Laser power: 2700 Watt Standard Equipment Machine - Sturdy, easily accessible C-frame - Coordinate guide system for high-precision machining - Linear magazine with 23 tool stations and 2 clamps - Maintenance-free three-phase drive motors - Repositioning unit with programmable hold-down device - Foot pedal for clamp closing - Alignment pin (right inside) - Ball tables - 2 parts flaps 500 x 500 mm incl. sensor for parts ejection - Two good parts containers - NitroLine - Focus Line - FastLine - FlyLine - Slag cone detection - Ejector cylinder for laser parts TRUMPF Laser - TruFlow 2000 laser with LensLine and optimized standby mode - High-frequency excitation - Cooling unit - Laser control - Enclosed beam guidance - Fine filtration of compressed air for beam tube ventilation Cutting Head - Lens cutting head with 170 mm focal length - Universal cutting head quick-change system UTI with bus connection - ControlLine Punching Station - Electro-hydraulic punching head Rjdpfxsylk U Ie Ag Nep - Rotatable mono-tool holder - Tool length compensation - Programmable hold-down device with manually adjustable holding force - Stroke counter for punch and thread-forming - Punch spray lubrication - Punch slug extraction - Measurement of fill level in punching console - Level monitoring for thread-forming and tool lubrication Control - TRUMPF control based on Rexroth IndraMotion MTX - Operating panel with 17" touch screen - Integrated technology data - Teleservice via internet - Programmable cutting gas pressure - Automatic shutdown incl. wake-up mode - Program management - Production scheduling Data Transfer - Network connection RJ45 and USB interface Safety - CE marking - Two-beam light curtain - Monitoring system for gas pressure, temperature, and cooling water - Emergency stop - Protection against stray radiation - Compact extraction unit + Brush tables + Lowerable die + MultiTool function + Softpunch function + Marking function + Chip conveyor with tilting container + Roll technology functions: roll knurling, roll deburring, roll shearing, roll offsetting, roll bead forming, roll cutting + Die spray lubrication + Blow-off device for small parts + 1 pc. additional clamp + Smart Punch Monitoring (punch breakage monitoring) + Vibration-damped installation + Repositioning cylinder + Warping detection + Parts conveyor belt in punching area + Parts conveyor belt in laser area + GripMaster (2500x1250) + Scissor lift table + Scrap grid pallet + SheetMaster (2500x1250) (AK04) + Peeling system + Automatic clamp closing + HZP loading/unloading + TwinCarts loading station with toothed belt drive + TwinCarts unloading station with toothed belt drive

Condition: good (used), Year of construction: 1999, operating hours: 52,324 h, functionality: fully functional, X working area max.: 1270 mm Redpoylk T Rsfx Ag Nop Y working area max.: 1270 mm Control: Bosch Type 3 Basic Standard equipment: - Robust C-frame - Safety light barriers - Coordinate guide with integrated linear magazine - 2 clamping claws - Automatic tool changer - Automatic repositioning - Tool length compensation - Forming capability - Mono tool holder with 360° rotation for all tools - Programmable hold-down device - Multitool drive - Punch slug extraction - Brush tables - Part chute 200 x 200 mm, sorting of parts into 2 containers - NC-controlled, digital, maintenance-free three-phase drives - Network interface RJ34 - 3.5" floppy disk drive - TOPS 2000 graphical programming - Online diagnostics via modem - Operating manual + Vibration-damped installation + Multitool + Thread forming + Start post

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, operating hours: 21,346 h, laser power: 3,200 W, X working area max.: 3000 mm Y working area max.: 1600 mm Control: Rexroth IndraMotion MTX Laser power: 3000 watts Machine - Enclosed machine frame - Hybrid axis system - Linear magazine with 20 slots for clamps and tools - Hydraulic clamps (3 pieces) - Maintenance-free three-phase motors for drives - Repositioning device with programmable hold-down - Foot pedal for clamp closing - Beam protection with direct access - Parts chute on the right - Parts flap on the left - Sensor for parts flap - Work area illumination - FocusLine - Retrofittable for SortMaster Compact - Protective tool - Transport and installation device TRUMPF Laser - Laser light cable (LLK) according to standard layout (10m) - Laser power control - Laser logbook function - Closed beam guidance via laser light cable (LLK) - Separate power supply for TruDisk Compact Cutting Unit - Solid-state laser compact cutting unit - Protective glass - Collision protection - ControlLine Punching Head - Delta Drive - Rotatable mono-tool adapter - Programmable hold-down position - Tool length compensation - Punch spray lubrication - Punch slug extraction - Forming function - Stroke counter for punch Control - TRUMPF control based on Rexroth IndraMotion MTX - Touch panel with 19'' TFT color screen - Integrated technology data - Programmable cutting gas pressure - Remote support interface - Auto shut-off with wake-up function - Program management - Production plan Data Transmission - USB interface - RJ-45 network interface - Central Link - Online Update Manager Safety - CE marking - Two-beam safety light curtain Extended Standard Equipment - TruDisk 3001 solid-state laser with 1 LLK output - Chiller (water-air) - Compact dust extraction system - 1st locating pin (right inside) - Ball tables - Good parts container for parts chute Rodpfx Agoylk S Tj Njp - Chip container for rear removal Extended Laser Equipment - Copper cutting package - Brass cutting package Extended Punching Equipment - MultiShear function - Multitool function - MultiBend function - Thread forming with thread counter Thread former breakage monitoring Lubricant level monitoring - Marking/fast embossing function - Engraving function - Deburring and roller technology function - Ejecting small parts function Parts Ejection - Integrated sorting function for parts chute • Sensor for parts chute • Tray line for 4 standard trays 300 x 400 mm • Customer-supplied trays Extended Machine Equipment - 1x additional clamp - Machine rated for ambient temperatures up to 43°C Special Sheet Metal Processing - Brush tables - Warping detection Options for Compact Dust Collector - CO2 extinguishing system for the compact dust collector Data Transmission - Wireless Operation Point Machine Accessories - 1 set RTC cassettes incl. die plate SheetMaster Compact - SheetMaster Compact 3000 x 1500 mm (AK05) • Loading station with spreader magnet for sheet separation • Suction frame • Vacuum sensor system • Double sheet detection • Unloading cart for scrap grid and microjoint sheets • 2nd operator's station for loading and unloading.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2014, laser power: 3,000 W, X Working area max.: 2500 mm Y Working area max.: 1250 mm Control: IndraMotion MTX Laser power: 3000 watts Standard equipment: Machine - Coordinate guide for high-precision machining - Stable, easily accessible C-frame - Linear magazine with 21 tool positions and 4 clamps - Drives with maintenance-free three-phase servo motors - Repositioning device with programmable hold-down device - Foot switch for clamp closing - Ball tables - 2 part flaps 500 mm x 500 mm - FocusLine - NitroLine - FastLine - Ejection cylinder for laser parts - Slag cone detection TRUMPF laser - TruDisk 3001 solid-state laser with 1 LLK outlet - Excitation via pump diodes - LLK according to standard layout (10m) - TruControl laser control 1000 - Cooling unit - Laser logbook function Cutting head - Solid-state laser compact cutting unit - ControlLine Punching head - Electro-hydraulic punching head - Rotatable mono tool holder - Tool length compensation - Programmable hold-down device (active / passive / repositioning) - Punch stroke counter and thread stroke counter - Spray lubrication of punch - Punch slug extraction - Calculation of filling level in the punching console - Level monitoring of thread forming and tool lubrication Control - Open control based on Rexroth IndraMotion MTX - Control panel with 17" touch control panel - Program management - Production plan - Integrated technology data - Teleservice via Internet - Programmable cutting gas pressure - Automatic switch-off with wake-up mode Data transfer - USB interface - RJ-45 network connection Safety - CE marking - Two-beam light barriers - Monitoring system for, among others Gas pressure, temperature, cooling water - Quick shutdown hydraulics - Protection against scattered radiation - Compact dust extraction system - MultiTool function - MultiBend function - Thread forming function - Engraving function - Deburring and rolling technology function - SoftPunch function - StripLine - Lowerable die - Spray lubrication die including level monitoring - Additional clamping claw - 4 pcs. Height-adjustable clamping claws - Vibration-damped installation - Chip conveyor with tilting container - Blow-out device for small parts - Warping detection SheetMaster - Unloading platform - Suction frame with 36 suction cups - Peeling suction cup - Vacuum sensors for each suction cup - Double sheet detector for double sheet control - Central lubrication - TRUMPF control based on Rexroth IndraMotion MTX - Automatic clamp closing machine - Loading and unloading parallel to production time - Peeling system including positioning aid medium format (2500x1250) - First additional suction cup package standard - Second additional suction cup package standard Rjdjylk D Nopfx Ag Nop - Unloading monitoring laser parts GripMaster - Parts conveyor belt punching station - Parts conveyor belt laser station ToolMaster with 70 stations (only for punching operation) - ToolMaster set-up parallel to production time

Condition: excellent (used), functionality: fully functional, Year of construction: 2010, laser power: 4,000 W, X working area max.: 3050 mm Y working area max.: 1550 mm Control: Rexroth IndraMotion MTX Laser power: 4,000 watts Standard equipment: Machine - Sturdy, easily accessible C-frame - Coordinate guidance for high-precision machining - Linear tool changer with 21 tool stations and 4 clamps - Maintenance-free three-phase drive motors - Repositioning device with programmable hold-down - Foot switch for closing clamps - 2 good parts containers - Automatic shutoff Laser station - TruFlow laser - High-frequency excitation - Cooling unit - TASC 3 laser controller - Enclosed beam guidance - Beam tube ventilation with compressed air - Programmable cutting gas pressure - Laser cutting head with 170 mm focal length - Universal quick-change cutting head device UTI with bus connection - LensLine - FocusLine - ControlLine - NitroLine - SprintLine - ContourLine - FlyLine - PlasmaLine - High-speed cutting - Additional Xp and Yp axes - Ejector cylinder for laser parts - Fast flap for laser parts 500 x 500 mm - Liftable laser cutting support - Slag cone detection - Laser logbook function Punching station - Electro-hydraulic punching head - Rotatable mono-tool holder - Tool length compensation - Programmable hold-down with adjustable force - Stroke counter for punches - Spray lubrication for punches - Punch slug extraction - Warp detection - Flap for punched parts 500 x 500 mm - Fill level monitoring in the punching console Control - Open control system based on Bosch Rexroth IntraMotion MTX - Operating panel with 15" TFT touchscreen - Program management and 80 GB storage capacity - Diagnostic function with laser logbook - Integrated technology data - Teleservice Data transfer - Network connection RJ45 and USB interface Safety - CE marking - Multi-beam light barriers - Monitoring system for, among others, gas pressure, temperature, cooling water - Hydraulic quick shut-off - Protection against stray radiation - Compact extraction unit - TruFlow 4000 Rjdpfjylk Nxex Ag Nop - Vibration-dampened installation - Thread forming function - MultiTool function - Chip conveyor with tilting container - Active die - Ejector for small parts - Brush tables with loading aid - Marking function - Repositioning cylinder - Warp detection

Condition: good (used), Year of construction: 2023, operating hours: 5,001 h, functionality: fully functional, X working area max.: 3000 mm Y working area max.: 1500 mm Control: TRUMPF Control based on Rexroth IndraMotion MTX Machine: - Closed machine frame - Hybrid axis system - Linear magazine with 24 slots for clamps and tools - Hydraulic clamps (3 pieces) - Drives with maintenance-free three-phase motors - Repositioning with programmable hold-down device - Foot pedal for clamp closing - Parts chute on the right Punching Head: - Delta Drive - Rotatable mono-tool holder - Programmable hold-down position - Tool length compensation - Punch lubrication spray system - Punch slug extraction - Forming function - Stroke counter for punches Control: - TRUMPF Control based on Rexroth IndraMotion MTX - Touch panel with 19" TFT color display - Touchpoint - Programmable cutting gas pressure - Automatic shut-off - Remote support interface - Program management - Production planning Data Transmission: - USB interface - RJ-45 network interface - Central Link - Online Update Manager Safety: - CE marking and EC Machinery Directive - Dual-beam safety light curtain Extended Standard Equipment: - 1st positioning pin (inside right) + Brush tables + MultiTool + Thread forming with thread counter + Thread-former breakage monitoring + Lubricant level monitoring + Marking/rapid beading + Deburring and rolling technology + Adaptive stroke calibration + Die lubrication spray system + Smart Punch Monitoring + Parts flap on the left + Parts conveyor belt for parts flap left + Collection tray for parts conveyor left + Sensor for parts chute + Parts conveyor for parts chute right + Additional clamp + 4x individually openable clamps + 4x height-adjustable clamps + Automatic clamp closing loading sensor system + Optical loading sensor + Automatic repositioning movement to compensate for loading tolerance + Repositioning device for DeltaDrive + Vibration-dampened installation + Chip conveyor with tilting bin + Machine status light + Warpage detection Rjdpfjylk H Dex Ag Nop + Wireless Operation Point SheetMaster Compact 3000 x 1500 (AK05): - Loading station with spreading magnet for sheet separation - Suction frame - Vacuum sensors - Double sheet detection - Unloading cart for residual grids and microjoint sheets - Second operator station for loading and unloading + Compact setup for light grid and reference point system + Peeling system SortMaster Compact: - Machine-integrated automated small part removal - Suction frame for unloading good parts up to 600 x 400 mm (X x Y) - 2 suction bars (each suction cup individually controllable) - Unloading area 600 x 800 mm - Vacuum sensors for the suction circuits + X-axis extension - Extension of the unloading area to 1200 x 800 mm

Condition: good (used), Year of construction: 2009, operating hours: 44,287 h, functionality: fully functional, X Working area max.: 2500 mm Y Working area max.: 1250 mm Operating hours: 44,287 hours Control system: Bosch PNC-P Standard equipment: Machine - Stable, easily accessible C-frame - Coordinate guide for high-precision machining - Linear magazine with 18 tool positions including 2 clamps - Drives with maintenance-free three-phase motors - Reloading device with programmable hold-down device - Ball tables - Part chute 180 x 150 mm - Automatic shut-off Punching head - Hydraulic punching head - Rotatable mono-tool holder - Programmable hold-down device - Tool length compensation - Punch spray lubrication - Punch slug extraction - Forming Control system - Open control system based on Bosch PNC-P - Control panel with 15" TFT color screen - Program management - Integrated Technology Data - Teleservice Data Transfer - USB Interface and Network Connection Safety Redpfoylk Emsx Ag Njp - CE Marking - Multi-Beam Light Barriers - Hydraulic Quick Shutdown + Multitool Function + MultiShear Function + MultiBend Function + Thread Forming Function + Marking/Fast Beading Function + Deburring and Rolling Technology Function + Soft Punch Function + Movable Support Table + Part Slide Sensor + Vibration-Dampened Installation + 2nd Stop Pin + Bow Detection

Condition: used, Year of construction: 1971, material width 180 mm Rodpfjylclfjx Ag Nsp coil weight 0,5 t material thickness 2,0 - 6,0 mm coil external diameter 400 - 1250 mm no. of straightening rolls 5 straightening roll diameter 70 mm number of draw-in rolls 2 0 roll diameter 110 mm speed 20 m/min power requirement 4,0 kW Weight 2,8 t dimensions (WxDxH) 1,4 x 2,45 x 1,85 m SPECIAL DEAL as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck

Condition: not inspected (used), Year of construction: 1967, functionality: unexamined, machine/vehicle number: 20590, overall weight: 5,000 kg, controller model: SIEMENS  COROS OP 15, roller width: 38 mm, No minimum price – guaranteed sale to the highest bidder! Bidding obligates timely pickup between 08.04.2026 and 16.04.2026! TECHNICAL DETAILS Thread rolling diameter: 200 mm Roll width: 38 mm MACHINE DETAILS Control system: SIEMENS COROS OP 15 Dimensions & Weight Dimensions (L x W x H): 5,500 x 2,000 x 2,200 mm Rodpfx Aeyk U T Ssg Nop Weight: 5,000 kg

Condition: used, Year of construction: 1975, functionality: fully functional, Paper Cutting and Rewinding Machine – Goebel Robust industrial equipment, manufactured in Germany, specifically designed for slitting and rewinding paper rolls. Delivers high precision in processing large reels and is ideal for preparing material for printing houses, packaging production, and other applications in the paper industry. Its solid construction and proven reliability ensure successful operation even after decades of use. Rjdpfx Agjxcxlue Njp