Used Round Bale Press for sale (15,987)

Condition: like new (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 630213235, The machine is in like-new condition! The technical data is provided by the manufacturer. The seller assumes no liability for its accuracy! TECHNICAL DETAILS Press force: 594 kN / 60 t Specific pressing force: 45 N/cm² Cycle time in idle mode: 25 s Idle press capacity (theoretical): 32.5 m³/h Filling height: 1,115 mm Feed opening dimensions: 1,195 x 650 mm Bale dimensions: 1,200 x 1,200 x 1,100 mm Max. bale weight: 550 kg Material to be pressed: Film, mixed paper, cardboard, punching waste MACHINE DETAILS Drive power: 4 kW Voltage: 400 V Frequency: 50 Hz Door design: Sliding door Door lock: Hydraulic Type of loading: Manual Consumables: Wire, looped wire Dimensions & Weight Dimensions (L x W x H): 1,780 x 1,568 x 2,985 mm Machine weight: 2,450 kg Njdpfoyqw Sqjx Alholc EQUIPMENT HSM TCS (TorsionControlSystem) for monitoring the inclination of the press plate Automatic start of the pressing process

Condition: good (used), Year of construction: 2005, operating hours: 15,606 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, power: 30 kW (40.79 HP), volume flow: 160 m³/h, Good day, We hereby offer you, without obligation, a used baler manufactured by Presto GmbH & Co. KG, model HPK 50 B. The following technical data have been taken from the manufacturer's operating manual and brochures, for which we assume no liability for accuracy or completeness. Manufacturer: Presto GmbH & Co. KG Model: HPK 50 B Year of manufacture: 2005 Operating hours: 15,606 hours Main press force: 50 t Drive power: 30 kW Total connected load: 31.5 kW Rated current: 64 A Throughput under operating conditions at a bulk density of 60 kg/cbm: approx. 6.7 t/hour Machine weight (press): 12.5 t Nledpfxsyplwfo Alhsc Note: The machine has been repaired in our workshop (the main control valve on the hydraulic block was replaced) and tested during ongoing operation in both manual and automatic modes. Machine documentation is available in German. Viewing of the press can be arranged by appointment in our workshop. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: good (used), Year of construction: 2008, operating hours: 24,629 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,650 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 24,000 kg, transport height: 3,000 mm, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 1,350 m³/h, transport width: 2,400 mm, transport length: 10,000 mm, Good day, We hereby offer you, without obligation, a used baling press from the manufacturer Presona AB, model LP 100 CH2 S. The following technical data has been taken from the manufacturer’s operating manual and brochures. We cannot guarantee the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Model: LP 100 CH2 S Year of manufacture: 2008 Total operating hours: 24,629 hours (as of February 2026) Effective pump operating hours: 10,090 hours Main press force: 100 t Specific compaction force: 81 N/cm² Pre-press flap force: 50 t Fill chute dimensions: 1,650 x 1,100 mm Fill volume per press cycle: 3 m³ Bale dimensions: 1,100 x 1,100 mm Drive power: 2 x 45 kW Tying: 5-fold vertical Hydraulic oil tank capacity: 2,000 L Transport weight (press only after disassembly): approx. 25 t Nlsdpfoymmmpex Alhoc Note: The machine was used in a recycling facility for compacting paper, cardboard, and films/foils. The press is in good condition and will be replaced by a new, larger machine in July 2026. Until then, it can be viewed in operation with materials processed. We would be pleased if this press is of interest to you. Your Service Team Mertens & Frowein GmbH

Condition: ready for operation (used), functionality: fully functional, pressing force: 38 t, MPC 20 PE compactor container Nsdpoyiltqjfx Alhelc

Condition: good (used), Year of construction: 1995, functionality: fully functional, pressing force: 70 t, filling opening width: 1,060 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 23,000 kg, noise level: 85 dB, power: 37 kW (50.31 HP), Used BOA 2060 for sale. The machine is currently stored in Belgium. It has been operational up until now and is currently disconnected. The machine is sold as-is, but a possible overhaul can be offered upon request. Technical data: Drive: 37 kW Pressing force: 70 tons Bale dimensions: 1100 x 720 mm Number of wires: 4 vertical, 2 horizontal Filling hopper dimensions: 1500 x 1060 mm Bale weight: approximately 500 kg (depending on material) Capacity: up to 14 tons per hour (depending on material) Press weight: 23,000 kg Njdpfx Aljya Uwpohjlc

Year of construction: 2001, condition: good (used), HSM-500.1_VL PRESS, PAPER PRESS, FOIL PRESS, BALING PRESS Immediately ready for use, good condition Used & good / see photos Model: HSM 500.1 VL Machine No. 6135.244.P Serial No. 220109689 Pressing force 50 tons V 400; Hz 50 kW 7.5 Amps 15.5 Pressing power 6 tons Year of manufacture 2001 More presses in our other offers Item used and good / roughly cleaned (Plug it in and you're ready to go) Dimensions: On request!! Additional photos show further possible uses. All items shown in the photos are also available from us. Price quoted net per piece upon collection from warehouse 47441 Moers Current stock: 1 piece Inspection is expressly offered. More equipment in stock see photos or inquire by phone General: We are offering articles from various acquisitions, which we describe as well as possible and provide informative photos. No further information can be provided about the item. Nlsdpfx Alolc Du Nehjc We offer the possibility of inspection on Tuesdays and Thursdays between 9 am and 4 pm by prior telephone appointment. If required, the item can be taken away immediately. Due to time constraints, we can only answer questions about this item if you provide us with a telephone number in your inquiry. Unless explicitly stated, this offer is for USED GOODS. Any packaging may be damaged. Items have been visually inspected and are technically in order as far as possible. All offers are ex warehouse 47441 Moers. If you would like shipping, please contact us to discuss packaging and shipping costs. If you are interested, please do not hesitate to call us. All dimensions are approximate. Errors and omissions in the description are expressly reserved.

Condition: new, Attachment suited for: Agricultural machines Nodpoyaud Njfx Alhslc

Condition: not inspected (used), functionality: unexamined, Harris TGS 215 3-RAM metal baler, 16” square with 600kw hydraulic power pack and hopper Video of baler in operation available on request, further details and photos to follow Machine decommissioned Nlodpfx Asw E Htujlhoc

Condition: used, Year of construction: 1995, functionality: limited functionality, cutting force: 800 t, empty load weight: 1,90,000 kg, type of input current: three-phase, Arnold HS850 Scrap & Metal Presse Die Maschine befindet sich derzeit in transportbereitem Zustand. master cylinder cylinder force: 850 t press: 0.08m/s hold-down cylinder cylinder force: 100t / per cylinder feed cylinder: cylinder force:100t cover cylinder: cylinder force:100t main dimensions total length:16175mm total width:5200 total height: 6420 mm Dimensions: Passage width at the scissor stand: 800mm passage height at the scissor stand: 800mm total height: 6000mm weights: scissor stand with cutter bar: 60 ton feed device approx: 85 ton total weight: about 170 tons required amount of oil: 5200 liters connection value of the machine: 220kw Nledpsh T Dctefx Alhsc If you need more information. We are here to help! Please contact us using the contact form or give us a call Your ad has been automatically translated. Translation errors are possible.

Condition: ready for operation (used), Year of construction: 2009, operating hours: 8,500 h, functionality: fully functional, fuel: diesel, IDROMEC 650 diesel engine plus generator, ready to use Nodpfx Aleyg Hcdohslc

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps Nedpfxey S Rqwe Alhslc 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Nledey R Nnfopfx Alhec Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. Njdpfxjzdn H Re Alhslc The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Model: Balestrini 1+1 dual-spindle turret press, patterning machine, 2500mm worktable size, used, tested. Nlodpfx Alszfi Sdshjc

Condition: ready for operation (used), Brand: HSM Type: V-press 860 plus Year of manufacture: 2012 Pressing force: 418 kN Voltage: 400 Nlsdpfx Aljzg Dptjhsc Max. bale weight: 480 kg (depending on the material) Bale dimensions: 120 x 120 x 78 cm Machine weight: 2083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Feed opening dimensions: 120 cm x 65 cm Video available upon request.

Condition: used, functionality: limited functionality, Year of construction: 2013, Gallignani baling press Nlsdjzb I Nhopfx Alhec Subject to prior sale – all information is provided without warranty. We cannot guarantee the accuracy or completeness of the information provided here. Any warranty and/or liability is excluded. Deviations from the description above cannot be ruled out. We would like to point out that the subject of the purchase agreement to be concluded will be exclusively the motor vehicle in its actual condition.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Nedpjvq Rtkofx Alholc Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Nlsdpezaqymjfx Alhjc Feed opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: good (used), Manufacturer: Comp Type: SB5 Motor: 2.2 kW Stroke length: 500 mm Nlsdpfjh Eic Asx Alhjc Chamber size: 500 x 350 x 400 mm

Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Model: HL 4010 Year of manufacture: 2012 Nsdex D U N Sopfx Alhslc

Condition: used, Year of construction: 2012, pressing force: 4 t, HSM V-Press 504 waste paper baler - used Njdpfeyim Ayjx Alholc The HSM V-Press 504 vertical baler is a compact yet extremely efficient device designed for pressing cardboard and plastic waste. Thanks to its robust construction, simple operation, and modern control system, this model is the ideal solution for manufacturing companies, warehouses, stores, and logistics centers where significant amounts of packaging waste are generated every day. The baler, manufactured by the German brand HSM, ensures reliable operation and a long service life. Key advantages of the waste paper baler: 40 kN crushing force – effective waste compression, reducing volume by up to 95%. Efficiency and ergonomics – the crushing process starts automatically when the door is closed, and the piston returns to its starting position automatically. Modern control system – a microprocessor with a membrane keyboard and graphic text display ensures easy monitoring of the work process. Double door with lever – safe and convenient operation even with intensive use. Compact bales up to 60 kg – facilitate transport and storage of processed waste. Integrated bale ejector – increases operator safety and comfort. Energy-efficient operation – 1.1 kW motor allows for full functionality with low energy consumption. Stable, durable construction – guarantees reliability over a long service life. The offer applies to the HSM V-Press 504 waste paper baler: • Product code: MTP006524 • Product condition: used • Year of manufacture: 2012 • Model: V-Press 504 • Width: 102 cm • Depth: 81.5 cm • Height: 193 cm • Weight: 290 kg • Power: 1100 W • Voltage: 230 V Net price: €2,859.00 per unit * I have large quantities available, with the possibility of negotiating the price for larger orders. * Transport possible throughout Europe. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: good (used), Impress HM 4 Hot Stamping Press This machine is in very good condition and ready to use. This machine is from the popular Impress hot stamping machine manufacturer, manufactured in the UK. Description The Impress hot stamping press is a hot stamping and embossing press for paper and plastics. It’s a useful device in any advertising agency or digital printing house. The manual press is powered by only 230V. A powerful press with adjustable pressure ensures repeatability and very high pressure between the die and the material. The machine features a worktop with a slide-out function, adjustable embossing depth, a heating plate with a thermostat, and an automatic foil feed. Nedpfx Aszday Rolhelc Specifications: Heating temperature control via thermostat Heating plate pressure mechanism: mechanical Press force: 1000 kg Power consumption: 500 W Power supply: 230 V Machine weight: 50 kg Plate size: 150 x 150 mm.

Condition: good (used), HFS-210 Hot Stamping Press The machine is in perfect condition. Year of manufacture: 2019. Description: The HFS-210 Hot Stamping Press is a pneumatic hot stamping press for hot stamping, embossing paper, and plastics. A useful device in any advertising agency or digital printing house. The cycle is operated manually. The pneumatic drive ensures repeatable work and very high die pressure on the material. The machine is equipped with an automatic foil feed, which significantly shortens the time of a single hot stamping cycle, a worktop, adjustable embossing depth, a hot plate ground to 0.01 mm accuracy, which significantly improves the quality of embossing with large dies, a control panel, and modern OMRON controls. Specifications: MODEL: HFS-210 Hot Stamping Press Heating plate size: 210 x 150 mm Work table area: 500 x 350 mm Heating temperature control: via display up to 200°C Holding foil adjustment: Automatic, potentiometer-controlled Hot plate pressure mechanism: pneumatic Height of the gilding stack: 68 mm Press force: 0.6 T Power consumption: 900 W Nodpfx Aljzdau Ueholc Power supply: 230 V Machine dimensions: 750 mm (W) x 530 mm (D) x 1670 mm (H) Machine weight: 120 kg The machine includes a cross table and a die mounting frame. An instruction manual is included.

Condition: good (used), Screw bookbinding press 40×30 with base The machine is fully operational and ready for operation. Format: 400×300 mm Nodozdat Ropfx Alholc Pressure: 3 tons Made in Germany.

Condition: good (used), Bookbinding press with tapping block The machine is fully operational and ready for use. Approximate format: 480 x 330 mm Nodezdatqepfx Alholc 3-ton pressure