Used Traub Tnc 65 Dgy for sale (96)

Condition: used, Year of construction: 2005, control Traub TX8i Isdpfx Adsxzk Rmjweht weight of the machine ca. 4000 kg

Condition: used, Year of construction: 1993, Technical details: x-travel: 400 mm y-travel: 300 mm z-travel: 400 mm spindle revolutions per minute : 8000 U/min control: Fanuc OM clamping table: 500x300 mm magazine slots: 16 Stück tool taper: SK40 distance work spindle /surface of the table max.: 50-450 mm numbers of pallets: 2 Stück/part total power requirement: 10 kW weight of the machine ca.: 2,5 t dimension machine xH: 2,4x1,8x2,5 m transport measurements machine: 2,45x1,8x2,5 m - E-cabinet - cooling device - chip conveyor manufacturer META (conveying height 1500mm; width 200mm) * Ihjdou Idn Hepfx Adwot

Year of construction: 2001, condition: good (used), bar diameter min. 18mm / max. 63mm Iedei Dagcspfx Adwjht bar lenght min. 1000mm / max. 4200mm

Condition: like new (used), Year of construction: 2022, operating hours: 13,116 h, Max. bar capacity mm: 20 Max. Z-axis travel (sliding headstock/fixed headstock) mm: 205 / 80 Max. spindle speed rpm: 10,000 Drive power 100%/40% duty cycle kW: 3.0 / 5.5 Torque 100%/40% duty cycle Nm: 5.73 / 10.5 / max. 17.2 C-axis resolution degrees: 0.001 Max. rapid traverse Z m/min: 20 Tool stations: 8 Driven tools: 8 Max. tool speed rpm: 12,000 / 8,000 Tool holder diameter mm: 45 Drive power 100%/40% duty cycle kW: 1.0 / 2.0 Turning tool cross-section mm: 16x16 / 20x20 Ihedpfx Adjwuddvjwet Slide travel X mm: 120 / 165 Slide travel Y mm: ±25.4 Slide travel Z mm: 254 / 567.5 Rapid traverse X/Y/Z m/min: 20 / 20 / 40 B-axis swivel angle degrees: 105 Lower turret: Tool stations: 8 Driven tools: 8 Max. tool speed rpm: 12,000 Tool holder diameter mm: 45 Drive power 100%/40% duty cycle kW: 1.0 / 2.0 Turning tool cross-section mm: 16x16 / 20x20 Slide travel X mm: 120 Slide travel Y mm: ±25.4 Slide travel Z mm: 155 Rapid traverse X/Y/Z m/min: 20 / 20 / 40 Back working device: Tool stations: 4 Slide travel X/Y/Z mm: 120 / ±25.4 / 155 Tool holder diameter mm: 25 Sub spindle: Max. spindle bore mm: 20 Max. spindle speed rpm: 10,000 Drive power 100%/40% duty cycle kW: 3.0 / 5.5 Torque 100%/40% duty cycle Nm: 5.73 / 10.5 / max. 17.2 Slide travel X mm: 235.5 Slide travel Z mm: 258 C-axis resolution degrees: 0.001 Rapid traverse X/Z m/min: 20 / 40 Coolant system basic unit: Pump pressure bar: 3 / 8 Tank capacity l: 250 Flow rate at 3 / 8 bar l/min: 80 / 120 Filtration degree µm: 200 Machine dimensions Length x width x height mm: see installation plan* Weight kg: 5,000* Connected load kW: 40 (47 kVA)

Condition: used, Year of construction: 2001, turning diameter 340 mm turning length 750 mm control SYSTEM TX 8H spindle passage 80 mm Isdpsxwdw Esfx Adwjht swing over plan sled 530 mm greates pass round over bed 665 mm turning speed range - main spindle 3.150 min/-1 drive capacity - main spindle 22 kW number of tool places 12 Pos. In our assessment, the machine is in good used condition and can be inspected under power by appointment. Two machines are available. Price per unit. Machine 1: - Images 1-5 - Operating hours approx. 55,790 h Machine 2: - Images 6-10 - Operating hours approx. 54,347 h Technical Features & Accessories: - Y-axis - Accessory package with rigid and driven tool holders - Chip conveyor Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and specifications, as well as prior sale!

Condition: good (used), Internal item no.: 25090 Driven tool holder Index / Traub No.: W 7045003 B Ihedpfx Adsxu Uz Nowot Very well-maintained condition! The holder was used on a Traub TNL18.

Condition: good (used), Year of construction: 2004, control TRAUB SYSTEM TX8H weight 3500 kg range L-W-H 3960 x 1640 x 1800 mm output 11 kW number of spindle speeds 5600 / 4000 min-1 Torque 200 / 280 Nm The TRAUB turning machine TNA 300 was designed for the following machining of workpieces with a turning length of 450 mm. --> for machining metal and plastics with a defined cutting edge using suitable tools. --> for mounting in jaw chucks of sizes 160 to approx. 250 --> for machining material bars up to a Ø of 42 or 65 mm --> with EHS special version Workpiece removal device --> chip conveyor 800 mm long -> Technical data Working range Spindle diameter: 42 mm --> Spindle head DIN 55026, size: A5 --> Clamping fixture diameter: 160-175 mm / 200-250 mm --> turning diameter max: 275 mm --> Distance over turning centre: 35 mm --> max. turning length: 450 mm --> Swing diameter over cross slide: 395 mm --> Swing diameter over bed: 520 mm --> Tool carrier Tool holders for cylindrical shank DIN 60880: 12 pcs. --> Shank diameter: 30 mm --> Chisel cross-section: 20x20 mm Iedjwwl Iujpfx Adwjht --> Switching time 1 station: 0.5 sec. --> Switching time each additional station: 0.15 sec. --> Feed drives X-axis: --> Slide travel: 210 mm --> Feed force: 5000 N --> rapid traverse/path speed: 15 m/min --> Z-axis: --> Slide travel: 450 mm --> Feed force: 6000 N --> rapid traverse/path speed: 18 m/min --> Y-axis: --> slide path: +- 35 mm --> Feed force: 6000 N --> rapid traverse/path speed: 10 m/min --> C-axis: --> Speed: 100 min-1 --> Torque: 140 / 196 Nm --> electrical resolution: 0.001 degree --> tailstock quill diameter: 70 mm --> quill stroke: 60 mm --> Stroke of the quick retraction: 280 mm --> quill setting force at 55 bar: 8600 N --> Mounting according to DIN 228: Mk 4 --> Steady rest Clamping range: 8 - 95 mm --> Workpiece removal device Max. part length: 250 mm --> Max. part weight: 3 kg

Condition: not inspected (used), Year of construction: 1989, We are offering the following as part of an insolvency sale: 2 x CNC lathes (1 x with sub-spindle, 1 x with lower turret), used + Bar feeder + Accessories 1. CNC lathe with sub-spindle Make: MIYANO Model: BNC 34-S Year: 1989 Control: Fanuc 0-T - HYDROBAR bar feeder - 2 x collet chucks - 1 x 3-jaw chuck 2. CNC lathe with 2 x turrets Make: MIYANO Model: JNC 45-T Year: 1989 Control: Fanuc 0-T - HYDROBAR bar feeder - 1 x collet chuck Ihsdpfxex Ed A De Adwot - 1 x 3-jaw chuck 3. Accessories - Approx. 65 x collets - Approx. 40 x jaw sets - Various tool holders + tools - Documentation The machines are untested, but they were in operation until decommissioning. Sale is ex-location; loading can be provided at extra cost.

Condition: used, Year of construction: 1994, functionality: limited functionality, spindle bore: 42 mm, spindle speed (max.): 4,000 rpm, spindle motor power: 7,500 W, The machine is in continuous operation, producing hydraulic fittings from hexagonal 22 (automatic steel). It is a very rigid and efficient machine for simple components. The machine is equipped with a FETTE tangential thread cutting attachment. Two such machines are available; one is additionally fitted with a side drilling unit and a thread milling attachment with a large set of milling cutters. Both machines come with a large set of tool holders and collets. Price for both machines is negotiable. Isdpfx Asxq Rz Djdweht

Condition: good (used), Year of construction: 2004, functionality: fully functional, Dear Sir or Madam, We are pleased to offer you a Traub TNL 26 CNC Swiss-type automatic lathe from the year 2004. The machine is in well-maintained, fully functional condition. Important Note: This particular model is equipped with only one turret. The TNL 26 was also manufactured in versions with two turrets – this offer explicitly refers to the version with a single turret. Technical Data (excerpt): Manufacturer: Traub Model: TNL 26 Year of manufacture: 2004 Control: Traub TX8i-S Turret: 1 unit, lower position, 12 tool stations, driven tools (all-head drive) Bar capacity: 26 / 32 mm Max. main spindle speed: up to 8,000 rpm Drive power: approx. 6.7 kW (100% duty cycle) / 10.7 kW (40% duty cycle) Torque: 21 Nm (100% duty cycle) / 32 Nm (40% duty cycle) Axes: X1 / Y1 / Z1, C-axis integrated in main spindle Chip conveyor: hinge belt, discharge height approx. 950 mm Isdpoxgg Rmsfx Adwjht Machine weight: approx. 4,000 – 4,200 kg Dimensions (L × W × H): approx. 4.4 × 1.4 × 1.7 m Condition & Application The machine is immediately available and ideally suited for the precise production of small and medium batches in the automotive, medical and precision engineering industries. Price & Terms Price: on request / negotiable Delivery: ex site, ex works Inspection: possible at any time by prior appointment. Should you require further information or wish to arrange an inspection, I am at your disposal at any time. Best regards, Arnd Sauter GmbH Björn Sauter

Condition: excellent (used), Year of construction: 2013, Traub TNL 18-7B CNC Automatic Lathe Base machine: 2441 x 1396 mm Weight: 3800 kg Spindle height above floor: 3800 mm Connected power: 24 kW Main spindle Max. bar capacity: 18 mm Max. speed: 12,000 rpm Ihjdpfx Adewg Takswot Cross-cut speed: 5,000 rpm Z stroke: 205 mm Rapid traverse: 40 m/min Z measuring system resolution: 0.001 mm Feed force: 3000 N Spindle head / short taper: Traub short taper mount Max. clamping force: 1400 daN Max. clamping pressure: 40 bar Min. clamping pressure: 7.5 bar Piston area: 40 cm2 Total cylinder travel: 5 mm Clamping tube thread: M25 X 1 Counter spindle Workpiece diameter: 21 mm Workpiece clamping depth: 180 mm Max. speed: 12,000 rpm Strokes: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Max. clamping pressure: 30 bar Min. clamping pressure: 10 bar Top tool turret with B-axis Number of stations: 8 Shank cross-section, turning tool: 16 x 16 mm Stroke: X: 120 mm Y: -25/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Chip-to-chip time: 0.5 sec Measuring system resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Lower tool turret Number of stations: 7 + counter spindle Shaft cross-section, turning tool: 16 x 16 mm Stroke: X: 120 mm Y: -20/+40 mm Z: 250 mm Rapid traverse: X: 20 m/min Y: 20 m/min Z: 40 m/min Chip-to-chip time: 0.5 sec Measuring system resolution: X: 0.0005 mm Y: 0.0005 mm Z: 0.001 mm Tool drive for upper tool turret Number of driven stations: Max. 8 Drive power: 2 kW Max. speed: 12,000 rpm Torque: 3.9 Nm Tool drive for lower tool turret Number of driven stations: 7 + counter spindle Drive power: 3.4 kW Max. speed: 12,000 rpm Torque: 7.3 Nm Tool drive for the rear unit Number of stations: 7 Number of driven stations: max. 3 Pitch spacing: 46 mm Drive power: 2 kW Max. speed: 7,500 rpm Torque: 4.7 Nm Drive power: 2 kW Max. speed: 4,000 rpm Torque: 11.8 SCOPE OF OFFER INCLUDES (list is not exhaustive): Traub CNC lathe Tool holders, driven and non-driven High-pressure and belt filter system Oil mist separator Fire extinguishing system Chip conveyor Bar loader Operational documentation For the exact scope of offer, see the photo gallery No liability is assumed for the accuracy, completeness, or timeliness of the information provided.

Condition: good (used), Internal item no.: 25091 Driven tool holder Adjustable angle head Index / Traub No.: W 7045011A Very well-maintained condition! The holder was used on a Traub TNL18. Ihjdpfxsxvaqle Adwet

Year of construction: 1989, condition: ready for operation (used), Spindle bore: 42mm, max. workpiece diameter: 115mm, speed: 3150rpm, power: 9kW, bar length: 5200mm. Machine dimensions X/Y: approx. 2100mm/1000mm, weight: approx. 1500kg. Including bar feeder Stamag D 5000 and various accessories such as collets and feed collets. Documentation available. An on site inspection is possible. Ihedpfx Adoxwn Ihowjt

Condition: good (used), Year of construction: 2001, TNK 36, year of manufacture 2001 including chip conveyor, Resy filtration system Ihjdpfjxv Sr Iex Adwjt In good condition, operated without loader, not under power

Condition: used, Year of construction: 1996, spindle passage 80 mm max. turning diameter 395 mm Max. Turning length 750 mm control System TX 8H max. Spindle speed 3.150 U/min. CNC lathe | TRAUB - TNA 400 Iedpfoxbtqvsx Adwoht The machine is in a well-maintained condition and can be inspected at any time under power. Technical data of the machine will follow soon. We ask for your understanding ! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags:TNA400 | TNA-400

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, spindle speed (max.): 8,000 rpm, bar passage: 32 mm, controller model: Traub TX8i-S, number of slots in tool magazine: 12, Equipment: chip conveyor, TECHNICAL DETAILS Bar capacity: 26 / 32 mm Max. main spindle speed: 8,000 rpm Axes: X1 / Y1 / Z1, C-axis integrated in the main spindle Turret: 1 Tool stations: 12 Drive power: 6.7 kW (100% duty cycle) / 10.7 kW (40% duty cycle) Torque: 21 Nm (100% duty cycle) / 32 Nm (40% duty cycle) MACHINE DETAILS Power-on time: 116,721 h Operating hours: approx. 48,000 h Control: Traub TX8i-S Iodpoxlfk Njfx Adwoht DIMENSIONS & WEIGHT Dimensions (L × W × H): approx. 4.4 × 1.4 × 1.7 m Machine weight: approx. 4,000 – 4,200 kg EQUIPMENT Chip conveyor: hinged belt, discharge height approx. 950 mm

Condition: good (used), Year of construction: 2002, TRAUB TNL 12/7 CNC sliding headstock automatic lathe TECHNICAL DATA Bar capacity: 12 mm Main headstock strokes: 130 / 80 mm Spindle power: 4 kW Speed, main spindle: 12`000 rpm Upper turret: 6 positions Lower turret: 6 positions Number of driven tools, turret: 6 Max diameter, counter spindle: 12 mm Ihedpfx Adst E Dbyewet Speed, counter spindle: 12`000 rpm Dimensions: 2850 x 1100 x 1480 mm SCOPE OF OFFER U.A: (list not exhaustive): Traub TNL 12/7 CNC lathe Meyrat high-frequency spindles, 2 pieces Tool holders (driven and non-driven) FMB Minimag 3200 C bar loader Hydraulic unit High pressure pump Chip conveyor Exact scope of supply according to photo gallery No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: good (used), Internal item no.: 25088 Tool holder Thread whirling holder incl. cutting inserts Index / Traub Ihsdexu Dcvopfx Adwjt No.: 12068219 The tool was used on a Traub TNL18 Very well-maintained condition!

Condition: good (used), Year of construction: 2005, operating hours: 32,870 h, functionality: fully functional, machine/vehicle number: 6030578, turning diameter: 32 mm, spindle speed (max.): 8,000 rpm, bar diameter (max.): 32 mm, We offer for sale Traub TNL26K automatic cnc lathe. Machine is connected to power and can be inpected every time by prior appointment. Year of built: 2005 Spindle passage 32mm Main spindle: 6.7/10.7kW; 8000rpm Counter spindle: 6.7/10.7kW; 8000rpm Upper turret: 12pos. 12x12/16x16, driven tools 2/5.5kW, 0-6000 rpm, 6.4/21 Nm Lower turret: 12pos. 12x12/16x16, driven tools 2/5.5kW, 0-6000 rpm, 6.4/21 Nm Connected load: 24kW Barfeeder: FMB Turbo 5-42/4200mm Ihsdpfx Aevldx Asdwot Swarf conweyor: Knoll 240 S1/100 Coolant Kompaktbandfilter: Resy Machine is sold with a lot of toolholders not driven and driven - list on attached photo.

Condition: excellent (used), Year of construction: 2000, operating hours: 49,274 h, functionality: fully functional, machine/vehicle number: 247, turning length: 80 mm, spindle speed (max.): 12,000 rpm, feed length X-axis: 35 mm, feed length Y-axis: 37 mm, feed length Z-axis: 75 mm, bar diameter (max.): 12 mm, No reserve price - guaranteed sale at the highest bid! TECHNICAL DETAILS Control: Mitsubishi TX-8i Turning length: 80 mm Main spindle Technology: belt spindle Speed: 12,000 rpm Power: 4 kW Torque: 7 Nm Bar capacity: 12.7 mm Travel path in Z1: 75 mm Workpiece clamping: collet chuck Counter spindle Technology: belt spindle Speed: 12,000 rpm Power: 4 kW Torque: 7 Nm Travel path in X3/Z4: 222 mm / 139 mm Rapid traverse in X3/Z4: 30 m/min Workpiece clamping: collet chuck Tool carrier I (X/Y) Ihsdpfx Adovrz E Hswjt Technology: turret with 6 stations (total drive) Tool holder: Ø 25 mm Tool drive: 8,000 rpm, 1.5 kW, 2.4 Nm Travel path in X1/Y1: 35 mm / 37.5 mm Rapid traverse in X1/Y1: 15 m/min Front attachment Number of stations: 4 Tool holder: Ø 28 mm Pitch spacing: 32 mm Tool drive: 12,000 rpm, 4 kW, 7 Nm Number of driven stations: 4 Travel path in X3/Z3: 222 mm / 139 mm Rapid traverse in X3/Z3: 30 m/min Rear attachment Number of stations: 4 Tool holder: Ø 28 mm Pitch spacing: 32 mm MACHINE DETAILS Dimensions: 1,450 x 950 x 1,480 mm Weight: 1,600 kg Connected load: 16 kW Installation dimensions: 7,943 x 1,430 x 1,480 mm Control switch-on time: 96,171 h Switch-on time: 100,147 h Production time: 45,983 h Spindle 1: 49,274 h Spindle 2: 47,771 h Spindle 5: 15,297 h EQUIPMENT - Chip management: Chip conveyor - Coolant management: KSS pump - Raw material feed: Bar loader, FMB minimag 3200 - Finished part removal: Workpiece removal device (pipe) - Emulsion mist extraction: Interface mechanically prepared - Tool holder: Various rigid and driven holders

Condition: used, Year of construction: 1997, spindle passage 80 mm max. turning diameter 460 mm Max. Turning length 1.000 mm control System TX 8F max. Spindle speed 2.800 U/min. CNC lathe | TRAUB - TNA 500 Ijdpexbtpxsfx Adweht The machine is in a well-maintained condition and can be inspected at any time under power. Technical data of the machine will follow soon. We ask for your understanding ! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags:TNA500 | TNA-500

Condition: good (used), Year of construction: 1993, - TRAUB control TX 8F - spindle passage 42 mm Ijdsldd Iqopfx Adweht - Working spindle speed: 40 - 4.000 1/min - 4 grooving slides: stroke 60 mm - 8-fold turret - high pressure pump 25 bar - backworking (2 spindles) - bar feeder (3 m) - chip conveyor

Year of construction: 1978, condition: used, Article: Programme-controlled automatic lathe Iedpfx Adsl Rmqtowsht Manufacturer: Traub Type: TF60 / 140 Yob: 1978 Bar automat Please, contact us for getting more information and pictures on mail(at) or *

Condition: good (used), Internal item no.: 25093 Driven tool holder Adjustable angle head Iedjxvat Topfx Adwoht Index / Traub No.: W 7045011A Very well-maintained condition! The holder was used on a Traub TNL18.

Condition: good (used), Internal item number: 25092 Driven toolholder Adjustable angle head Manufacturer: Index / Traub No.: W 7045011A Ihedoxvazkopfx Adwjt Very well-maintained condition! The holder was used on a Traub TNL18 lathe.