Used Ultrasonic for sale (253)

Condition: used, Strip Processing Line - Decoiler and Straightening Machine Year of manufacture: 1991 Strip width: 50 to 450 mm Sheet thickness with straightener inactive: 6 mm Sheet thickness with straightener active: 2 mm - Excellent equipment and feed-in aids Required floor space for the complete line (L x W): approx. 7000 x 3000 mm Total weight of the system: approx. 11 tons Good condition Straightening Machine HMS Type RS 47-04/1, Machine No. Strip width, nominal: 400 mm Gisdsif Sg Sopfx Anxot Strip width, max. pass-through: max. 455 mm Strip thickness at 400 mm width: max. 1.5 mm (steel) Strip thickness at 400 mm width: max. 2 mm (copper) Speed: max. 40 m/min Number of straightening rollers: 7 pcs Straightening roller diameter: Ø 40 mm Number of pinch rollers: 2 pcs Pinch roller diameter: Ø 80 mm Entry height, pass height: 1500 mm - Straightening rollers hardened, ground, and hard-chromed, with central support - Pinch rollers hardened, ground, and hard-chromed, with hydraulic disengagement - Manual straightening roller gap adjust - Feed-in aid with hydraulically extendable tongue and hydraulically adjustable deflection roller - Adjustable side strip guide - All straightening rollers driven via distribution gearbox with cardan shafts - Both pinch rollers driven via gearbox with cardan shafts - Frequency-controlled drive via geared motors - Straightening machine opening stroke 250 mm for cleaning or processing thicker material, stroke movement via trapezoidal thread spindle - Ultrasonic loop control Transport dimensions (L x W x H): 3600 x 2200 x 2200 mm Nett weight: approx. 4 tons Decoiler HMS Type BA 1.5-06/80, Machine No. Coil weight: max. 8000 kg Coil outside diameter: max. 1600 mm (with coil car) Coil outside diameter: max. 2000 mm (without coil car) Coil turntable diameter: Ø 1700 mm Coil inside diameter, expanding range: 460-520 mm Coil width, nominal: max. 630 mm Spreader jaw width: 750 mm Height of the decoiler drum above base plate: 1500 mm - Decoiler drum driven by hydraulic motor and gear - Pneumatic run-on brake on decoiler drum, TWINFLEX - Hydraulic expansion of the decoiler drum, centrally via wedge slider system - Hydraulic hold-down arm with hydraulically driven double pendulum roller - Coil car with 12 tons lifting force and 300 mm stroke - Decoiler frame above floor with motorized cross travel drive Transport dimensions (L x W x H): 3500 x 1900 x 2500 mm Nett weight: approx. 5 tons Central hydraulic unit, adjacent Tank capacity: 350 liters Motor power: 18.5 kW - Drive motor with 2 REXROTH pumps (tandem pump) - Oil cooler as air heat exchanger with fan motor Transport dimensions (L x W x H): 1600 x 850 x 1450 mm Nett weight: approx. 800 kg Electrical cabinet, adjacent - All cable connections via Harting connectors Transport dimensions (L x W x H): 2800 x 500 x 2250 mm Nett weight: approx. 800 kg

Condition: used, Year of construction: 2011, functionality: fully functional, total length: 4,130 mm, total width: 830 mm, total height: 1,800 mm, The Sodeva CEL 250 ultrasonic slicer is a major innovation for the food industry. Thanks to ultrasonic technology, it ensures precise and clean cutting of products, thus improving production quality. Furthermore, this machine significantly reduces residue and waste, contributing to a more efficient use of raw materials. Furthermore, the Sodeva CEL 250 can slice a wide variety of products, offering significant flexibility for businesses. Furthermore, this slicer integrates easily into existing production lines, facilitating the transition to more modern cutting methods. As a result, businesses can increase their productivity without requiring major modifications to their facilities. Furthermore, its operation is simple and intuitive, reducing staff training time. As a result, operators can quickly become familiar with the machine, optimizing performance from the moment it is installed. In summary, the Sodeva CEL 250 ultrasonic slicer is an ideal solution for improving production efficiency and quality while reducing operational costs. Technical Specifications: Gsdeu Iazvjpfx Anxjit Ultrasonic Slicer Type: CEL 250 Year: 2011 Dimensions: 4130 x 830 x 1800 mm (L x W x H) QUMP2F+D

Year of construction: 2025, condition: new, functionality: fully functional, load capacity: 75 kg, The Wave 450 parts cleaning unit is a very flexible vacuum assisted degreasing machine able to perform an high degree of parts decontamination. All the operations such degreasing cycle as spray, immersion jets, ultrasonic, as well the distillation and filtration process and parts drying treatment are sequenced in automatic way and in a total vacuum ambient. The Wave 450 machine can operate with: Modified Alcohol solvents (MA) / Hydrocarbons Class III (H-III) / Chlorinated (PER) Those solvents are specifically used when the demand calls for a strong degreasing phase, evaporate completely without leaving debris residues on the processed parts. Standard features  Continuous solvent distillation  Full solvent distillation  Sludge stripping 2nd distiller Oil/solvent separation  Full solvent filtration at each cycle  Chip drying and deodorizing before emptying by the operator  Chip drying and deodorizing before opening / cleaning by the operator  Vacuum / solvent charging - discharging system  Water/solvent separation Distillation Giodowc Sdaopfx Anxjt The distillation of the solvent enalble to maintain unchanged the degreasing power of the solvent. All our systems offer the double stage distiller as standard, guaranteeing the separation between solvent and oils, further expulsion of water takes place in the water separator. PLC S7 and HMI 12" Siemens are a standard feature The machine is compliant to Industry 4.0 and so Industry 5.0. Basket dimension is: mm 480 x 300 x 200 H

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: 06 61 230, Order No.: Lg 34022 Single-Sided Decoiler BBT ABH 1000/300 New Machine Year of manufacture: 2026 Machine No.: 06 61 230 Technical Data Load capacity: max. 1,000 kg Strip width: max. 300 mm Inner coil diameter: approx. 360 to 420 mm Outer coil diameter: approx. max. 1,400 mm Uncoiling speed: approx. 2 to 15 rpm With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase gearbox motor. Expansion of the support segments is manual via hand crank and joints. Number of support segments: 3 Coil side guidance via robust adjustable arms, lockable. The decoiler stand is built in a heavy-duty box-section design as a welded construction. Optional equipment: Shutdown 'Loop too small' via antenna switch, mounted on the column of the loop control base housing. Height infinitely adjustable. Strip side guide on the base housing of the loop control, adjustable in passage width by means of lateral guide rods. Godpfsyur Tdjx Anxoit Currently in pre-sale. Delivery time approx. 3 months. Image shows reference machine.

Condition: new, Year of construction: 2025, Technical Data / Equipment Straightener: R65/360 Godpfewhfxzjx Anxsit • Strip width 30 - 360 mm • Strip thickness from-to 0.6 - 4.0 mm • Strip thickness throughput: max. 4.00 mm • Max. straightening cross-section: 800 mm2 at R02=350 Nmm2 or 150 x 4 mm • Straightening speed: 2 - 20 m/min • Number of straightening rollers: 7 • Straightening roller diameter: 65 mm • Number of draw rollers: 2 • Draw roller diameter: 65 mm • Motor power: 2.2 kW/3x400V RK machine body with a very stable and torsion-free welded construction RZ straightening and draw rollers, made of high-quality steel, surface-hardened and finely ground mounted in maintenance-free roller bearings AG drive, via spur gear motor with Double chain drive EM self-regulating drive, via frequency converter, with WM position measuring system, belt loop control for self-regulating drive, with ultrasonic sensor and sensor in the belt loop RZ straightening roller adjustment, individually manually adjustable and readable via dial gauges RO discharge roller cage, fixed with a radius for 3 mm material thickness PZ pneumatic tension roller adjustment, operated from the control panel BSF-ze belt side guide, manually adjustable centrically and eccentrically by 25 mm SS-2 interface to the press:

Condition: refurbished (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 20170259471, total length: 22,000 mm, total height: 2,000 mm, total width: 2,000 mm, control cabinet length: 2,400 mm, control cabinet width: 400 mm, warranty duration: 12 months, control cabinet height: 2,200 mm, year of last overhaul: 2025, Side Sealing Machine - Manufacturer: BVM Brunner GmbH & Co. KG - Machine type: Comtex 4G - Machine No.: 20170259471 - Year of manufacture: 2017 - BVM reference no.: 5947 - Voltage, Frequency: 3N 400V, 50Hz - Power specifications: P=18kW, I=26A, F=32AT - Condition: Fully refurbished with warranty Comtex 4G Shipping System: The BVM shipping system ‘Comtex 4G Shipping’ is the complete solution for mailing various items directly to customers, including labeling. Delivery notes, invoices, and goods are packed together in a tightly sealed PE film bag, labeled with the address sticker, and handed directly over to the respective logistics partner. Technical data: - Seal width: 750 mm (transverse), 800 mm (longitudinal) - Product height: up to 250 mm - Capacity: Up to 25 cycles/min* (Special) features: - Special color - Signal control light with three colors to indicate error messages - Pneumatically operated buffer plate and presence control for the film waste tray, enabling tray change during automatic operation (no machine stoppage required). Note: At this station, the Comtex working height is limited to 850 +/- 10 mm. Godpjw Ryt Dofx Anxeit - Electronically controlled sealing bar drive (servo-driven, stepless speed adjustment) - Film end detection by ultrasonic sensor, incl. analog input card (one per film carrier) - Mechanical distribution device for film scrap strips in combination with a large film scrap storage - Individual wire numbering in the control cabinet of the packaging machine for Comtex 3G and 4G - Grooved aluminum profile covered with plastic profile - Bypass conveyor as folding belt integrated in the Comtex downstream of the side sealing station for transferring products out of the machine - Film folding device (no separate control) for converting flat film into center-folded film - Film sealing device for flat films - PN/PN coupler (Profinet coupler) for establishing a Profinet connection - Software development for PN/PN coupling including release connection, interlock and combined fault message - Film end detection at the film mount and film level detection at the film unwinder, detected by photoelectric sensors, including three-color signal lamp and acoustic signal - Mounting preparation for labeler, suitable models on request, installed at the infeed including electrical and pneumatic connections - Sealing bar for producing a wide seal seam with separate cold knife cut, suitable for Comtex 3G, 4G and Compacta with EGS - Manual labeling device with linear motion (Model: Caljan Type: FPS BVM L113 L) - Reclosable film bag by means of double-sided adhesive tape in the film bag, incl. tear-off perforation wheel - Additional tear-off perforation wheel, allowing complete removal of the bag’s edge area - Stand-alone control cabinet for Comtex with 5 meter cable - Two sequentially mounted indexing belts (600 x 900 mm/600 x 14,000 mm) for Comtex 4G (total length 14,950 mm) with space for installation of a scanner or camera incl. trigger light curtain for scanner - Height adjustment of cross seal for pass-through height 220-250 mm - Cognex scanner system, consisting of: -- Scanner below the infeed for delivery notes -- 2 overhead scanners -- 1 overhead scanner for control +++ Fully refurbished equipment with 12-month warranty according to our attached warranty conditions +++

Condition: used, Year of construction: 2001, material width 410 mm coil weight 2,0 t coil internal diameter 380 - 520 mm coil external diameter 1400 mm Giodpfx Ajvut Thonxot power requirement 2,2 + 1,1 kW weight of decoiler 0,7 t dimensions decoiler (WxDxH) 1,4 x 1,4 x 1,65 mm weight of the pulling device 1,15 t required space of the pulling device (WxDxH) 1,7 x 1,1 x 2,2 m Decoiler 2370 DFPS without drive, with pneumatic lag brake, hydraulic centralized expansion, pneumatic snubber roll pulling device / hydraulic threading device 235 D with infinitely variable drive, coild loop control via ultrasonic material thickness up to approx. 6,0 mm roll diameter approx. 160 mm

Condition: used, Year of construction: 1994, material width 650 mm coil weight 3,5 t Giodpfx Anevut Sdexet material thickness 0,8 - 3,0 mm no. of straightening rolls 7 straightening roll diameter 80 mm number of inlet rolls 4 coil internal diameter 460 - 530 mm coil external diameter 1400 mm weight straightener 1,0 t weight decoiler 0,9 t dimensions straightener (WxDxH) 1,5 x 1,9 x 2,0 m dimensions decoiler (WxDxH) 2,2 x 1,8 x 1,9 m Feeder-straightening machine DREHER 1676 E/RDS Modell 1529/4 with infinitely variable drive Decoiler DREHER 2380 FM-FPS Modell 891/5 motoric driven. with pneumatic lag brake, manual centralized expansion, pneumatic snubber roll coil loop control Ultrasonic

Condition: good (used), Ultrasonic sensor, ultrasonic sensor, ultrasonic generator, ultrasonic generator -Manufacturer: Dukane, iQ Port Probe Switch Gisdpext E Htefx Anxjt -Type: MPCQH0402 -Number: 7x Port Probe Switch available -Price: per piece -Dimensions: 240/145/H45 mm / 240/180/H50 mm -Weight: 1.2 kg / 1.4 kg

Condition: good (used), Ultrasonic sensor, ultrasonic sensor, ultrasonic generator, ultrasonic generator Gjdpfjxt E A Ijx Anxoit -Manufacturer: Dukane, iQ Aim ultrasonic generator -Type: 20HB260-2P-C3 -Number: 12x generator available -Price: per piece -Dimensions: 430/265/H140 mm -Weight: 12.2 kg/pc.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: xxxxx, Washing machine Manufacturer: CIEFFE Type: WCR 8/X/"/VAP/US/G-R Giedpoqtyxkjfx Anxot Year of construction: 2007 Heating: 120kW gas Evaporator vacuum boiler, ultrasonic, dryer, compact de-oiler, level controller Cleaner tank 4500 ltr. Flood tank 4500 Ltd.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, The Flowpacker is ideal for packaging different product formats in flow packs - whether flat, lying on its side, stacked or pre-packed. Thanks to its design as a pre-configured machine, you benefit from fast delivery and can start using your Flowpacker in a very short time. Integrated 3D image recognition systems detect the position, location, height and quality of the products and ensure that the robots only pick the perfect products. High quality sealing Giodpfxouni Abs Anxot Depending on the product characteristics and the desired film, the seamlessly integrated Flowpacker is equipped with one of four different sealing technologies. Especially for heat-sensitive products, we have developed a new and unique sealing technology: First, an ultrasonic sealing system seals the longitudinal seam of the flowpack, followed by a heat sealing system with a movable cutting unit. This moving cutting unit adapts to the variable speeds of the above F4 robots and thus guarantees high sealing quality with constant sealing times.

Condition: good (used), Year of construction: 2010, functionality: fully functional, Mixer tank with blender, YIT Industrial and Network Services Ltd 2010. 3000L, stainless steel. ABB motor and SULZER gearbox. Siemens 7ML5221-1AA1, SITRANS Probe LU ultrasonic level transmitter monitors level and volume in liquids and slurries. Sprinkler washing system. Drain outlet at the bottom and a tap on the side. Condition like new with minimal usage. Estimated motor hours: under 100h. Has been used for clay and glaze. Second tank in main picture included in the price, tank only – no motor, etc. Gjdpfoylpxfjx Anxsit

Condition: used, Year of construction: 2015, Year: 2015 Condition: excellent Counter status: only – 640,000! - Machine inspection: possible - Availability: immediately Configuration: - 1 × DSF 6000 digital feeder - 1 × DBM 600 stitching and folding unit - 2 × Hohner stitching heads - 1 × DBM 600T face trimmer - 1 × long conveyor (delivery unit) Specifications: Feeder (DSF-6000) - Feeding speed: up to 600 sheets/min - Stack capacity: approx. 610 mm - Paper size: - Min: 120 × 210 mm - Max: 364 × 525 mm - Paper weight: 64 – 300 g/m² - Buffer: approx. 10 sheets - Technology: - Air Management separation system - Anti-static system - Optical + ultrasonic sensors (double feed detection) - Weight: approx. 300 kg Specifications Duplo 600i - Speed: 4,500 – 5,000 booklets/hour - Format: - Min: 120 × 148 mm - Max: 356 × 508 mm - Paper weight: 52 – 300 g/m² Godpjyyby Ejfx Anxeit

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Gsdpfxjyx Uy Ao Anxjit Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Year of construction: 2015, condition: ready for operation (used), This TELSONIC TelsoSPlice TS3-6 P3.6 wire welding sytem was manufactured in 2015. It features a 15" SVGA touch screen, a pneumatic unit, and a 3.6kW WeldHead. The machine includes a barcode scanner, keyboard, and a spacious 2000 x 1000 mm table. Consider the opportunity to buy this TELSONIC TelsoSPlice TS3-6 P3.6 Table. Contact us for more information about this machine. • System: TelsoSplice Plus • Technology: Ultrasonic wire splicing / wire compaction • Application: Ultrasonic welding of wire strands for splice production and compaction Gjdpfx Anjx D E A Asxeit • Material Capability: Bare copper wires • Restriction: Wires must not be tinned • Plastic Welding Capability: Not suitable for plastic welding • Total Welding Counter: 1490 welds • Recorded Welds / Compactions: approx. 490 • Ultrasonic Frequency: 20 kHz • Ultrasonic Power (Welding Tongs): 3 kW • Generator Power: 3.6 kW • Amplitude Accuracy: Stabilized ±3 % • Wire Cross Section Range: 0.26 mm² – 40 mm² • Cylinder Force at 6 bar: 1750 N • Cylinder Force at 7 bar: 2040 N • Insertion Stroke (Opening): 19 mm / 10.5 mm • Maximum Tool Torque: 20 Nm • Maximum Air Supply Pressure: 10 bar • Maximum Operating Pressure: 7 bar • Compressed Air Quality: ISO 8573-1:2010 [2:3:2] • Pneumatic Connection: Pneumatic hose Ø8 mm • Voltage Supply: 3 × 400 V / 230 V • Power Supply Type: 3LNPE • Frequency: 50 – 60 Hz • Nominal Current: 3.3 A • Maximum Peak Current: 6.0 A eff • Power Factor: cos φ > 0.95 • Minimum Line Protection: 3 × 13 A slow-blow • Protection Class: IP20 • Control System: SPC Module-4 • Operating System: Windows Embedded Standard 7 • Touch Panel PC: 15" SVGA Touchscreen • TelsoSplice Software Version: 3.5 • Version: 3.5.50929 • Microsoft Framework Version: 4.0.30319.34209 • Ultrasonic Generator: MAG • Generator Output Power: 3.6 kW • Weld Head: TS3-6 • Power Cable: 3 × 400 V / 230 V MAG/SPC-4 • Power Cable Length: 3 m • Pneumatic Unit: TelsoSplice TS • Adapter / Power Cable: MAG/SPC-4 • Rack Housing: 19" 8U • Emergency Stop: TelsoSplice Table E-Stop • Foot Switch: TelsoSplice Foot Switch • Barcode Scanner: Manhattan CCD Long-Range • Keyboard: US Layout • Key Set: TelsoSplice Key Set • Cable Set: TelsoSplice Table / Standing Version • Machine Table: TelsoSplice Table L • Table Size: 2000 × 1000 mm • Complete System Weight (Table Version): approx. 103 kg • Operating Temperature Range: 10 °C – 40 °C • Humidity Range: 20 % – 80 % (non-condensing)

Year of construction: 2005, condition: ready for operation (used), This SUMITOMO SHI DEMAG El-Exis S 250/630-1450 was manufactured in 2005. It features a central accumulator for high-speed injection and chromed tie bars. The pump drive power is 22.0 kW, with a mains voltage of 400 V/50 Hz. It includes a color data display with VGA interface, an oil cooler, and electric screw drive. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis S 250/630-1450 hydraulic injection moulding machine. Contact us for more information. • 5x similar units available • Central accumulator for high-speed injection; core, ejector, and nozzle movement • Nozzle movement parallel to mold movement • Chromed tie bars on clamping unit • Pump drive power: 22.0 kW • Mains voltage: 400 V / 50 Hz, 3 Ph + N + PE • Separate mains connections for drive and heating • Control: color data display with VGA interface and AT keyboard interface • Injection, holding pressure, and back pressure via servo valve • Reinforced oil cooler • Separate water connections for mold and oil cooling • Compliance: Basic version Europe, according to valid safety regulations Gjdpfxsx D Rqrs Anxoit • Painting: Bottom anthracite grey RAL 7016; Top blue 571C MD • Elastic machine mounting • Ultrasonic displacement measuring system with digital data transmission for injection, ejector, mold (WZ), and nozzle (AWH) movements; 1/100 mm resolution for injection axis • Reduced centering diameter (D=100/125) for fixed mold platen • Mold connection dimensions type E (similar to EUROMAP), without side ejector plate • Standard mold installation height • Safety interlock: mold opening and ejector forward only with closed safety door • Ejector with position control via proportional valve; pressure and velocity independently programmable • Electric screw drive, frequency-controlled

Condition: used, Year of construction: 2017, Year: 2017 Condition: good Schulze PRETREATmaker IV A unique device for applying penetrant liquid before textile printing. Thanks to the dimensions of the area it is capable of apply liquid (40x60 cm) is especially suitable for DTG printers M2, M3, M4, but of course also for printers with a smaller printing area flat, such as R-Jet, Brother GT3, Anajet, TexJet... The advantage is that it does not need a compressor. The machine is equipped with 4 independent and adjustable nozzles (you can apply only small area, e.g. when printing logos on hearts). Spraying time of full area 40x60 - 4.5 seconds. Optional spray size liquids of 2 cm each (2 - 60 cm length). Large clear LCD display. 5 storable positions/area and quantity settings injection. High efficiency and productivity of work. It does not need a compressor * The machine has 4 independently adjustable nozzles (you can apply only a small area, e.g. when printing logos on hearts) * Spraying time of full area 40x60 - 4.5 seconds * Optional liquid injection size of 2 cm (2 - 60 cm length) * Large clear LCD display * 5 storable positions/area settings and spray amount * High efficiency and productivity of work PRETREATmaker IV is a top-of-the-line device designed for the professional application of penetrating liquid to textiles. It has an advanced electronic system, which enables high performance and easier control during the textile pretreatment process. Clear color touch screen allows you to easily adjust the length and width of the spray and to easily adjust the spray volume. The device is equipped four nozzles, each of which can be switched on individually. This allows you to precisely adjust the area to apply the penetrating solution (Dupont Artistri, Image Armor, Brother...) but also saves a lot of penetration compared to applying by hand with a pressure/air gun. The length of the spray area can be regulated in 2 cm increments, using the touch screen. To set the amount of penetration liquid application, 10 values are available. Pre-treat maker IV also has an automated cleaning process for the spray nozzles (consumption approx. 12 ml per hour), which keeps nozzles through and prevents them from drying out or blocking. Spray area: 40 x 60 cm Spray method: Nozzles move above the table (inside) Table length: 80 cm Nozzles: 4 pieces Dimensions: T 90 x W 72 x H 48 cm Dimensions (for transport): T 95 x W 80 x H 61 cm Weight: 68 kg Weight (for transport): 86 kg Connection: 220/230 or 110/120 VAC (automatic switch) Consumption: 150 W Operating pressure (before coating): max. 7 bar Menu: 5 languages: German, English, French, Italian, Polish Measurement: "cm" or "inch" Included in delivery: spare nozzle, spare filter and ultrasonic cleaner Other features: galvanized and powder-coated housing Gjdpfxsufi Uws Anxeit

Condition: used, Year of construction: 2017, Thermal Transfer Press Godpfxoufknrj Anxsit Year: 2005 Status: functional Model: Schulze Air press x Double pneumatic transfer press, semi-automatic model. The pressure can be adjusted using an air pressure gauge, which also ensures the same pressure regardless of the quality of the garment. Digital temperature and time control. After the transfer is complete, the will open automatically. Bottom plates are available in different sizes. • Print format: 400 x 500 • Dimensions: 1.67 x 0.74 x 0.98 m • Weight (including packaging): 170 kg • Power consumption: 10 A / 230 V • Temperature: max. 220 °C • Temperature accuracy: ± 0.5% • Power: 2.4 kW • Heating time: 12 min. at 180 °C • Timer range: max. 9 min., 59 sec. • Operating pressure: 2490 kg Schulze PRETREATmaker IV Year: 2017 Condition: good A unique device for applying penetrant liquid before textile printing. Thanks to the dimensions of the area it is capable of apply liquid (40x60 cm) is especially suitable for DTG printers M2, M3, M4, but of course also for printers with a smaller printing area flat, such as R-Jet, Brother GT3, Anajet, TexJet... The advantage is that it does not need a compressor. The machine is equipped with 4 independent and adjustable nozzles (you can apply only small area, e.g. when printing logos on hearts). Spraying time of full area 40x60 - 4.5 seconds. Optional spray size liquids of 2 cm each (2 - 60 cm length). Large clear LCD display. 5 storable positions/area and quantity settings injection. High efficiency and productivity of work. It does not need a compressor * The machine has 4 independently adjustable nozzles (you can apply only a small area, e.g. when printing logos on hearts) * Spraying time of full area 40x60 - 4.5 seconds * Optional liquid injection size of 2 cm (2 - 60 cm length) * Large clear LCD display * 5 storable positions/area settings and spray amount * High efficiency and productivity of work PRETREATmaker IV is a top-of-the-line device designed for the professional application of penetrating liquid to textiles. It has an advanced electronic system, which enables high performance and easier control during the textile pretreatment process. Clear color touch screen allows you to easily adjust the length and width of the spray and to easily adjust the spray volume. The device is equipped four nozzles, each of which can be switched on individually. This allows you to precisely adjust the area to apply the penetrating solution (Dupont Artistri, Image Armor, Brother...) but also saves a lot of penetration compared to applying by hand with a pressure/air gun. The length of the spray area can be regulated in 2 cm increments, using the touch screen. To set the amount of penetration liquid application, 10 values are available. Pre-treat maker IV also has an automated cleaning process for the spray nozzles (consumption approx. 12 ml per hour), which keeps nozzles through and prevents them from drying out or blocking. Spray area: 40 x 60 cm Spray method: Nozzles move above the table (inside) Table length: 80 cm Nozzles: 4 pieces Dimensions: T 90 x W 72 x H 48 cm Dimensions (for transport): T 95 x W 80 x H 61 cm Weight: 68 kg Weight (for transport): 86 kg Connection: 220/230 or 110/120 VAC (automatic switch) Consumption: 150 W Operating pressure (before coating): max. 7 bar Menu: 5 languages: German, English, French, Italian, Polish Measurement: "cm" or "inch" Included in delivery: spare nozzle, spare filter and ultrasonic clean...

Condition: like new (used), This equipment is ideal for sterilising various types of juices, fresh milk, beverages, wines, and other liquid products. It is also suitable for soya milk and animal feed liquids. When used in combination with a homogeniser, it is capable of processing high-viscosity materials such as sweetened condensed milk, among others. The high-pressure homogeniser is a type of ultra-fine grinding and emulsification equipment. It operates by subjecting the suspension to high pressure, then passing it through a unified decompression zone. Bulging, implosion, shearing, and high-speed impact occur in an adjustable flow-restriction gap. This pulverises particles and oil droplets in the liquid to a very fine size, resulting in an ideal emulsion and a homogeneously dispersed liquid. This process integrates the effects of ultrasonic atomisation, colloid milling, ball milling, and jet milling. Homogenisation enables improvements in product stability, consistency, mixing properties, absorption, nutritional value, shelf life, flavour, colour, and palatability. Gedpfx Asx S E E Aonxjit

Condition: excellent (used), Year of construction: 2015, Item: Galdi RG270UCS Used Filling machine: Galdi RG270UCS, for the inline forming, filling and sealing of Gable Top cartons. Pure-Pak Classic with Crew Cup Production year 2015 Pure-Pak Classic Ultrasonic Screw Cap Applicator moved by servomotors, many spare parts incl. The machine has been in production to 2021 and was dismantled q2 2021. Gjdpfx Anjiiyr Iexeit Carton size 70 x 95 mm, 1500ml Speed up to 7000 cartons per hours Filler Volumetric piston filler + Bottom up Lenght 7715 mm Width 1500 mm Height 3655 mm More technical details can be provided upon request. We offer two pieces identical machines.

Condition: like new (used), total width: 615 mm, total length: 685 mm, total height: 771 mm, type of input current: DC, transport height: 800 mm, • “NEW Machine” customer experience • Ultrasonically cleaned, Wrapped, boxed • Refurbished with long life parts/original • Parts cleaned • Precisely assembled • Original toner filled to 30% in the machine (Approx. 7,000 prints/color) • Updated English firmware • Counter reset • Pre-installed, tested: plug in and use Giodpoxac R Nsfx Anxot • Minimum 400,000 page machine life guaranteed • ISO certificate • Environmentally friendly

Condition: refurbished (used), functionality: fully functional, • “NEW Machine” customer experience • Ultrasonically cleaned, Wrapped, boxed Gijdpfjxanycjx Anxot • Refurbished with long life parts/original • Parts cleaned • Precisely assembled • Original toner filled to 30% in the machine (Approx. 7,000 prints/color) • Updated English firmware • Counter reset • Pre-installed, tested: plug in and use • Minimum 400,000 page machine life guaranteed • ISO certificate • Environmentally friendly

Condition: new, A mass production washing machine where parts are transported by hanger conveyor and washed by passing through tunnels. Washing is done by spraying or immersion ultrasonic dipping. Giedpfx Aed I E Itonxet Working Principle: Parts are transferred by hanging on to the hooks of the top loading conveyor belt. General process cycle: Washing - Rinsing - Optionally Ultrasonic Immersion Washing - Drying All of the HANGWASHes are tailor-made and have lots of options depending on your needs. Please feel free ot contact with us for further information.

Condition: new, Year of construction: 2024, Cabin Type Parts Washer for precise cleaning of metal parts. INTERSONIK ROTAWASH is a cabin type parts washer which provides precise cleaning and perfect drying. Its effectiveness is proved on automative industry especially in engine block washing and cylinder head washing. Operation Principles: Effective washing of whole surfaces of the work piece with high Gedpfx Aned I A Hrjxsit volume spraying and rapid liquid feeding to cabin. With rotational motion, whole complicated surfaces, oil channels, blind holes, water jackets of work piece is provided completely clean and dry. Hermetic operation system prevents the diffusion of water vapour formed during whole operation. Whole operation is controlled via PLC Other Details - The machine has sound and durable body construction. - Automatic water supply and chemical design system provide minimum system (maintenance) care and maximum operation performance. -The water contact surfaces are made of stainless stell. -Body covers and control panels are made of epoxy painted stell sheets,which are provided and guaranteed long and continious working life. -Ultrasonic system integration is also available as an option. engine block washing, power train washing, high presssure washing machine, rotational washing machine, cabin type washing machine, cabin type parts washer, parts washer, solvent washer Please feel free to contact with us for other details and options.