SECOND-HAND 4+1 SPINDLES MOULDER

Steton FAST-5S

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Hodpjwu Tu Dofx Ag Nei Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, Year of construction: 1999, x-travel 2000 mm y-travel 800 mm z-travel 850 mm control HEIDENHAIN TNC 360 total power requirement / kW weight of the machine ca. / t required space / m Hjdjv H Ertjpfx Ag Nsi

Condition: excellent (used), Year of construction: 2008, The condition of the machine is excellent, it has performed only 14078 operations. CNC controlled machine, designed for processing welded frames. Multiple use of the same time Hjdom Ak R Ujpfx Ag Noi He works in a welding and cleaning line It does not take up additional space in the hall It can work in the line of frames, sashes or mixed All operations are performed during cooling: dehydration vents, grooves venting, holes in colored profiles drilling the frame for the post connector drilling holes for the hinge in door frames (x6) drilling holes for the hinge in the leaf (x2) The center has its own transport of frames from the welder to the cleaner PLC control, NC User-friendly visualization

Condition: used, Year of construction: 2014, power capacity 3 kW feed pressure 7 bar liter capacity / l weight 286 kg Chicago Pneumatic CPVR15 CE screw compressor - Year of manufacture 2014 The CPVR15 CE impresses with its robust design, long service life and low operating costs. Whether in workshops, workshops or industrial applications - this compressor reliably supplies you with the compressed air you need. Drive power: 3 kW Delivery pressure: 7 bar Air output: up to 58 CFM (approx. 1,640 l/min) at 7 bar Weight: 286 kg Dimensions: approx. 965 mm (L) × 620 mm (W) × 1,040 mm (H) Operating noise: approx. 50-58 dB(A) Hsdpsh A Sfdofx Ag Noi Voltage/frequency: 415 V / 50 Hz Application: Workshops, craft businesses, industrial applications with medium compressed air requirements Included in delivery: 1x compressor - Chicago Pneumatic CPVR15 CE 1x refrigeration dryer - OMI ESD 108 - 0.70kW 1x Beko Öwamat 2 - oil-water separator Technical data was taken from publicly available sources

Condition: used, Chipping roundwood: 100-150 m3/h Hjdpfxjhclffo Ag Nsi Chipping small waste: 50-100 m3/h Weight: 3165 kg Max log diameter: 254 mm Söderhamn Eriksson 670-56 CC chipper with electric motor. Söderhamn Eriksson 670-56 chipper is intended for the production of chips for pulp, fibreboard and chipboard manufacture. Both roundwood and sawmill waste may be used as raw material. Chipper 670-56 feed is horizontal, at an angle of 37,5 grades to the grain. The chips, of consistent high quality, may be discharged at the bottom or blown straight upwards. Be one of those woodworking companies that wisely manage the resources available to them.

Condition: good (used), functionality: fully functional, We offer for sale a complete line for multi-point automatic welding of SCHLATTER brand steel wires. Hodpotvpilsfx Ag Nsi We have three fully operational production lines. There are also automatic machines for the production of transverse wires (so called slitting machines with a cutter). We also have a number of single point welding machines for steel wires.

Condition: ready for operation (used), For turning plates, slices or trays up to 250 mm Ø Machine with vacuum clamping Hodpfx Agjrh Hnte Noi

Condition: excellent (used), Line for door jambs (frames), with END-CUTTING, ROUTERING for COUNTER-PLATE and HINGE INSERTION (Anuba). Composed of: X10030A) Loading Conveyor X10030B) Transfer Conveyor Hsdpfxjqwycls Ag Nei X10030C) Double-end cutting and drilling machine "AMS" - Left-side Cutting 45° - Drilling - Cutting 90° - Right-side Cutting 45° - Drilling X10030D) Angular Conveyor (90°) X10030E) Anuba Inserting Machine "MASTERWOOD" Mod. MULTITEC X10030F) Strike Plate Routering Machine "MASTERWOOD" Mod. Teknomat 3000

Condition: good (used), functionality: fully functional, Year of construction: 2012, machine/vehicle number: 778 F 319, Lazer Cutting Fabrikat: Prima Power Typ: Palatino 1530 Baujahr: 2012 Hedpfx Aemx Rrleg Noi

Condition: used, Year of construction: 1986, plate thickness 6,0 mm pressure 18 t cutting angle - upper blade 90 ° blade length 225 x 225 mm Hedeg Ip Efspfx Ag Nsi voltage 380 V total power requirement 5,5 kW weight of the machine ca. 650 kg dimensions of the machine ca. 1,10 x 0,80 x 1,05 m - Angular stops adjustable