Vötsch VTU 60/60 drying oven 250°C

Vötsch Vötsch VTU 60/60

Condition: used, functionality: fully functional, Used Schenck Balancing Machine H 50 V/B with used CAB 690 H measuring unit. (Can be upgraded to a new CAB 920 unit for an additional (18 000–20 000€) The machine comes with original foundation drawings, documentation and manuals. The machine can be test run in Kerava. Rotor Capacity - Rotor weight range: 20 – 6 000 kg - Maximum symmetrical load on pedestal bearing: 7 500 kg - Maximum symmetrical load on stand bearing: 3 750 kg - The machine can be loaded freely with lower weights when following recommended procedures. - Maximum rotor length between pedestals:1 600 mm (belt drive) - Maximum diameter over machine base: 2 100 mm - Clamped rotor diameter ranges: 25–180 mm, 180–380 mm - Machine bed length: 3 500 mm - Balancing speed n depends on the rotor’s moment and must be selected to avoid overloading the drive. - Maximum permissible G·n² value: 1400 × 10⁶ kg/min² Iedpsx Ein Ssfx An Doia - Applies to a rigid symmetrical rotor mounted on pedestal bearings. - May be exceeded during dynamic tests on flexible rotors and strength tests. - End drive / FU motor: 7,5 kW - 4-speed gearbox: 120–2520 rpm - Belt drive BU 5 / FU: 7,5 kW - Unbalance Umar 0,5 gmm/kg: 0 gmm/plane

Condition: used, Year of construction: 1998, workpiece weight 150 kg Isdewcg Elepfx An Doia workpiece length 2500 mm diameter 160 - mm balancing speed variable 100 - 3000 U/min dia. axle journal 160 - 350 mm voltage 400 V total power requirement 1,5 kW weight of the machine ca. 1,5 t dimensions of the machine ca. 7,50 x 1,30 x 1,60 m Control 0,60 x 0,60 x 1,85 m Software TIRA X9000 Operating System Windows XP Software update 2007 Serial No.: R 32/98 Max display sensivitiy: 0.5 gmm Balancing speed 100 - 3000 RPM

Condition: good (used), functionality: fully functional, Year of construction: 2006, laser power: 4,000 W, AVAILABLE AT SHORT NOTICE: TRUMPF Trumatic L 3030 - 4 kw - Year 2006 TECHNICAL DATA: Make: TRUMPF Type: L 3030 - 4 kw Year of manufacture: 2006 Working area: 3,000 x 1,500 x 115 mm Control: Siemens Sinumerik 840 D Laser power: 4,000 watts Max. Sheet thickness mild steel: 20 mm Max. Sheet thickness stainless steel: 15 mm Max. Sheet thickness aluminum: 10 mm Operating hours: NC Machine regularly serviced by TRUMPF! Transmitter tube: new 2024 TASC laser control: new 2022 Driver stage: replaced 2018 Magnetic bearing electronics: new 2016 STANDARD EQUIPMENT: - Closed machine frame with integrated laser unit Laser unit: TLF 2000 high-frequency excited CO2 laser, maintenance-free turboradial blower, mirror telescope, cooling unit, logbook function - Automatic pallet changer - Longitudinal conveyor belt for small parts/waste - Drives: maintenance-free three-phase servomotors - Cutting head quick-change device - Laser cutting head with 5" lens and laser cutting head with 7.5" lens - Programmable cutting gas pressure setting - APC capacitive height control and process control - AutoLas Plus automatic focus position adjustment - Laser power control - Position laser diode - HI-LAS high-pressure cutting - Fast processing with SprintLas - ContourLas for the production of small holes - PMS plasma sensor technology - Automatic sheet edge detection - Programmable power cycles - Microweld - Automatic switch-off - Work area lighting - Sinumerik 840D control system: open control system on PC basis, simple operation, online help, integrated e-shop, diagnostic functions, maintenance logbook, technology data, teleservice - Workshop programming ToPs 100 lite - Safety: multi-beam light barriers, beam guidance fully encapsulated and ventilated, Iedpfjuthz Tsx An Dsia monitoring system, multi-chamber extraction and compact dust extractor, protective cabin - 3.5" floppy disk drive - TFT color screen - Electrical equipment: Voltage 400 V / 50 Hz - Paint finish: Standard RAL 9002/5010 EXTENDED EQUIPMENT: - TLF 4000 laser incl. lens monitoring sensors - PCS Process Control System

Condition: new, PAK-1 Unbalance Measuring Unit is designed to modernize your balancing machine. A balancing machine has a long mechanical life, but prolonged use leads to gradual failure of electronics and measuring instruments, causing problems with spare parts and lack of technical support. Minimize downtime and ensure the reliability of your balancing machine by upgrading it with a new advanced measuring unit. The PAK-1 unbalance measuring unit works in all balancing machines of most existing designs and manufacturers. Iodoq Ttn Dopfx An Dsia Confidence in results and ease of use: Easy to set up and work with, our devices do not require any special theoretical knowledge. Wide range of functions for your balancing machine: The use of modern microprocessor technology and many years of experience of our developers allows us to implement functions that were previously unavailable to other manufacturers. Your machine complies with ISO 21940: Balancing machines equipped with the PAK-1 unbalance measuring unit fully meet the precision requirements of modern standards. HIGHLIGHTS • We make balancing easier - the main advantage of our balancing systems. • The balancing process is displayed in real time and the unbalance behaviour of the rotor is monitored on the screen to achieve the best possible result. • The maximum sensitivity of the machine at any moment of operation, the set-up and calibration of the machine is carried out by the operator himself. • Free from the influence of external vibration factors on the measurement result, it has a high degree of protection against various types of interference. • Easy to learn working skills and maintenance for any employee. INCLUDES: 1) vibration sensor signal processing unit, 2) fanless industrial computer with touch screen, 3) new vibration and speed sensors, 4) metal protected cable set. SEQUENCE OF WORKS for modernization of the measuring unit - Replacement of the existing measuring system with the balancing complex PAK-1 based on an industrial computer; - Installation of new vibration sensors and rotor speed sensor - Replacement of all connecting cables; - Adjustment of the measuring unit on the balancing machine; - Training of personnel with skills to operate the machine. VTM GROUP offers to upgrade your balancing machine. We repair and modernise various old balancing machines of all types from all manufacturers. It's cost effective. An alternative to buying a new balancing machine in 95% of cases. Urgent. Work can be done at customer site within 1-2 days. New components for modernization of your machine: • Installation of new measuring system and vibration and speed sensors. • Installation of new electrical equipment • Manufacturing or repair of the rotation drive • Manufacturing of new rollers Every business is different. Let's discuss your task. We can offer a solution for any balancing machine. Please contact us to get the best offer! 👇

Year of construction: 2026, condition: as good as new (ex-display), Parts cleaning machine / spray cleaning system type TR450 The spray rotary cleaning system type TR450 is an automatic cleaning and degreasing system with a cover that can be easily opened upwards. The system is designed for cleaning individual parts and/or bulk goods in baskets measuring LxWxH 520x320x200h mm. The basket must be closed with a lid for the cleaning process. The cleaning result depends on the fact that the parts can be easily circulated in the basket in the case of bulk goods. The fill level in the basket must be observed for this. The system is also equipped with a flood tray under the basket, which enables the parts to be scooped up in a flood, thus achieving an even better cleaning result. including the following equipment: - Completely made of stainless steel 1.4301 inside and out - Level monitoring and automatic fresh water refill - Insulation of the entire system - Hot air drying (output: 11.6 kW) - Steam vapor extraction - Oil skimmer for bath maintenance - Automatic fresh water refill Iiedpfsfbt Sijx An Dea - 1 small parts basket 520x320x200h mm, mesh size: 6x6 mm, incl. height-adjustable lid Connected load: approx. 20 kW (32 amp plug)

Condition: ready for operation (used), Year of construction: 2015, - USED - FIBER LASER CUTTING MACHINE WITH PALLET CHANGER and LOADING/UNLOADING SYSTEM X-AXIS TRAVEL: 4000 mm Y-AXIS TRAVEL: 2000 mm Z-AXIS TRAVEL: 115 mm RAPID FEEDS X-Y-Z: 245 m/min WORKING AREA: 4000 x 2000 mm ADMITTED LOAD ON TABLE: 1250 Kg SOURCE: TRUDISK 5001 ; 5000 W Iiedpexqtx Sofx An Dja WEIGHT: 15000 Kg OVERALL DIMENSIONS: 10900 x 5700 x 2400 mm NOTE: LIFT MASTER COMPACT LOADING/UNLOADING SYSTEM

Condition: good (used), Code: 0136 Brand: ITALPRESSE Model: FORMATIC 20.9 Hydraulic fluid membrane press Two sided lamination of veneer to panels shaped or profiled on one face and flat on the other to produce cabinet door raised panels, drawer fronts, desk tops, table tops, kitchen tops, etc. 3-D lamination of plastic foils (PVC, PPE, ABS, Transfer foil ) to panels sheped or profiled on one face to produce: cabinet doors, drawer fronts, desk tops, table tops, kitchen tops, store fixture components, room doors, etc. Platen dimensions mm 2000 x 900 Daylight mm 325 Cylinder stroke mm 325 Heating electric boiler Kw 27 Thrust ton 300 ton N° 3 thrust cylinders Iisdpfx Aepbvqvon Dja Hydraulic unit power Kw 5,5 Pressure control manometer Automatic pressure reset Opening timer Overall dimensions mm 3300 x 1400 x 2400 h Weight kg 8100

Condition: new, Year of construction: 2026, The laser processing center skyCUBE M / P / SL - the new standard in laser material processing! (* Prices depending on equipment, this is a brand new laser machine from our production) Laser options according to your needs: CO2 laser 150W / 250W / 400W or fiber laser 1500 - 6000W Iisdpfxobnphvj An Dsa PFEIFER laser processing center skyCUBE Processing areas: Mclass = X 1250 x Y 650 x Z 100mm Pclass = X 1250 x Y 1250 x Z 100 mm SLclass = X 1250 x Y 2550 x Z 100 mm skyCUBE laser processing center - the new multifunction laser engraving machine and laser cutting machine - laser processing easy - high precision - laser engraving, cutting with high speed and quality. Our new and best multifunctional talent not only impresses the most experienced user with its newly thought-out construction. This CO2 laser / fiber laser shows its outstanding capabilities as a CO2 or fiber engraving laser as well as a CO2 or fiber cutting laser in all industrial applications. With an optional laser power of up to 1500W (1.5kW), the CO2 laser device / fiber laser system can also be used extremely flexibly in your production. skyCUBE laser devices meet all requirements of class 1 according to DIN EN 60825-1 and thus offer you the highest level of safety. Depending on the selected and installed laser power, this CO2 laser / fiber laser is ideally suited for cutting and engraving many materials, such as: various metals, acrylic glass, solid wood and wood-based materials, wood composite materials, paper, cardboard, various plastic and foam materials, textiles, and much more The excellent design of the laser machine, 100% produced in Plauen/Germany, guarantees the laser user a high working accuracy with consistently high quality from the metal construction to the laser source. With a cutting speed of up to 8000 mm/s and an engraving speed of up to 4000 mm/s, the high-quality laser technology produces clean and very sharp cut edges and precise laser engravings. The ergonomic design with a pull-out work table makes it easier to load the system. A drawer in the lower part of the machine is used to collect the clippings. User-friendly and intuitive - the supplied skyCUBE PC software (ready for Windows®). A simple, practical user interface adapted to the Windows standard lets you work quickly and effectively. The software is characterized by high system stability, professional monitoring with appropriate machine operation and control as well as compatibility with common file formats. The data is output via levels - separately for each level, including definition of the sequences and the type of processing. The parameters, such as laser power and processing speed, are automatically saved for each level and can therefore be retrieved in a material database at any time and can be reproduced. With a computer connected via LAN / USB interface, the laser projects are transferred to the skyCUBE M laser processing center. From there, these can be processed repeatedly without the PC having to be switched on. A modern touch control panel gives you access to all system information and functions. Laser processing center skyCUBE at a glance: German industry standard Machine steel construction for safe and vibration-free accommodation of the laser components and axis systems, on rollable industrial leveling feet

Year of construction: 2015, condition: ready for operation (used), A Nabertherm circulating air chamber furnace is available. Connected load: 30kW, max. temperature: 650°C, volume: 500l, heating-up time: approx. 60min, internal dimensions X/Y/Z: 750mm/1000mm/750mm. Machine dimensions: approx. 1300mm/1900mm/1850mm, weight: approx. 750kg. Documentation available. On-site inspection possible. Iijdpfoxrf Iuex An Dsa

Condition: used, Automatic Platen Die Cutter ETERNA ML 930 GII with 3 Operation modes Halbautomatischer Stanztiegel / Automatic Platen Die Cutter ETERNA ML 930 GII Year 2008 - Serial-No. EP51568 Format 670 x 930mm Operating modes: Single, Continuous nd with time delay on opening Electromagnetic clutch and brake Included frame and tools, in very good condition Iiodjx U Adnjpfx An Dsa Safty Cover Weight 3800kgs - Power supply 380 V Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test