Debarker

Valon Kone VK-820-2R-620/620-8/6-600

Condition: excellent (used), Storti RM 500 edger - Italian production - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm - max disc diameter 600 mm - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment - two lasers - feed speed 25 and 50 m/min - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions Lajdpok Talpsfx Akfoa 500x240x180 cm weight 3500 kg

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: Laodjwp Rqfjpfx Akfoa • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: refurbished (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 12786 040, overall weight: 20,000 kg, rotor diameter: 640 mm, total length: 4,900 mm, total height: 2,600 mm, total width: 4,100 mm, rotor width: 2,000 mm, power: 203 kW (276.00 HP), rotational speed (max.): 340 rpm, input current: 415 A, Equipment: rotational speed infinitely variable, The Vecoplan VAZ 2000 M F-T is a powerful single-shaft shredder. This robust shredder offers an efficient and reliable solution for a wide range of applications. Possible applications: - Household waste - plastics Lasdpfx Aourkc Rskfea - paper With its proven technology and high throughput of 4-5 tons per hour, the VAZ 2000 M F-T is the perfect choice for shredding and volume reduction in disposal and recycling processes. The pictures are examples. The pictures do not show the machine as it is offered, they only serve as an example of what the machine will look like after the overhaul. Price on request.

Condition: ready for operation (used), Logintake with butt end reducer and debarker. Below parts included: Lajdpjtrd Hfofx Akfea - Log deck with log unscrambler and log singulator - Butt-end reducer type Bruks RR1000 - Debarker type cambio 70-66 - Out-feed log conveyor with logkicker

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 3595, Ladies and Gentlemen, We are selling a Weiler Commodor B lathe built in 2001 with Heidenhain 3-axis digital readout. The machine has been extensively overhauled in our workshop. Among other things, the main spindle bearing and the lead/traction spindle bearing were completely renewed! Technically, geometrically and visually, the machine is in excellent condition, which you are welcome to see for yourself on site. Availability: on request Machine no. 3595 Year of construction: 2001 Center height: 180mm Center width: 1000mm spindle passage: Ø 56mm max. spindle speed: 2000 rpm Tailstock taper mount: MK4 Feed range: 0.026 - 0.888 mm/rev Possible thread types: Metric, inch, module, diametral pitch Metric thread pitches: 0.35 - 12 mm Spindle brake: switchable Laedpfxjthd Sho Akfea Connected load: 4kW Dimensions: approx. 2.2x1.5x1m (LxHxW) Weight: approx. 1.8t Further equipment and accessories: 3-axis digital display, coolant device, chuck guard, pull-out chip tray, 3-jaw chuck Röhm, 4-jaw chuck Röhm, various clamping jaws... Our service promise to you: - We are a certified master company in the field of mechanical engineering - All machines are thoroughly checked - All lubricants and any worn parts are replaced in advance - On request, we can completely or partially overhaul your chosen machine - On request, we can repaint the selected machine in the color of your choice E00f3g2rl - On request, you can also order additional accessories such as tools etc. directly - On request, we can install additional accessories such as safety devices etc. - We are happy to take care of shipping and/or installation

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit Lajdou Hmacspfx Akfea non-driven extraction table Machine workshop checked Machine cleaned and repainted

Year of construction: 1998, condition: excellent (used), functionality: fully functional, Very stable creel roller conveyor with hydraulic lift and lowering cross conveyor. 1st part: Length 7,100 mm. Roller length 2,000 mm. Roller diameter 220 mm. Overall height 1,000 mm. Built-in hydraulic lifting and lowering cross conveyor Lsdpfxjt Hg Huj Akfsaa With 4 chain strands. Spacing: 1,500 - 1,300 - 1,000 mm. Fully plated. Hydraulic model support rollers. Drive via geared motor. New bearings. 2nd part: Length 7,200 mm. Roller length 1,600 mm. Conveyor length 6,100 mm. Built-in hydraulic lifting and lowering cross conveyor with 6 chain strands. Unsupported, it is possible to convey the cut material under the roller conveyor to the left or right. Fully plated. Including hydraulic unit for both roller conveyors.

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Lodjq Nf Enepfx Akfsaa Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Condition: new, Year of construction: 2025, The automatic stacker is suitable for stacking boards of different lengths in layers. The stacker automatically adjusts to the board length to be stacked. The desired stacking height can also be preset. The power consumption of this machine is only 12 kW. Lodpfx Akohbr Tpsfjaa ARBOR designs and manufactures stackers individually - according to your production parameters. . . . . . . . . . . . . . . . ARBOR manufactures equipment of varying complexity for woodworking enterprises.

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm Laodpfxovbtps Akfea