Wide belt sander

Vertongen S-320

Condition: excellent (used), Through-feed sander Vertongen S320 Working width 300 mm Working height up to 180 mm Combi unit with pad Manual raising and lowering of the working table Codpfxjyg Dlce Aizori Two feed speeds: 7–14 m/min Main motor 5.5 kW

Condition: excellent (used), Year of construction: 1998, I sell the window production set: 1pc. tenoning profiling centre Weinig Unitec 10 1pc. profiling automat centre Weinig Univar 10 Year 1998. Moulding heads OERTLI. Available immediately. Crodjfzzhyspfx Aizei Total price 17.000 euro. Condition very good !

Condition: good (used), Surface grinding machine, grinding machine -hydraulic horizontal surface grinding machine -Magnetic plate: 300 x 150 mm -Grinding wheel motor: 1.1 kW 2800 rpm -Water cooling with: filter -Grinding disc diameter: 200 mm -Transport dimensions: 1470/1170/H1920 mm Cedjd A Idxepfx Aizeri -Weight: 1090 kg

Condition: reconditioned (used), Year of construction: 2004, AUTOMATIC WINDMILL PRESS WITH MECHANICAL LOCKING AND FEEDING AFTER A COMPLETE RENOVATION Cjdpelnanwjfx Aizori

Condition: used, Leitz HM - IV 66 window set with sash and door handle set Sold as is, tools have not been newly sharpened, Ex works, from the Seevetal location, Cjdpfxehzgy Ne Aizeri excluding transport, subject to prior sale.

Condition: new, Finger-setting machine with a segmented top clamp PNEUMATIC CYLINDER!!! Max. setting capacity over the entire working length ----- 1.5 mm Max. working length ----- 1500 mm Max. opening width ----- 48 mm Width of the fingers ----- 25 | 30 | 35 | 40 | 45 | 50 | 75 | 100 | 150 | 200 | 2x 250 | 275 mm Max. setting angle ----- 0 - 135 degrees Weight ----- 430 kg Width ----- 1820 mm Crjdpfoga T Dljx Aizji Depth ----- 850 mm Height ----- 1175 mm

Condition: refurbished (used), Year of construction: 1990, Drum chipper / chipping machine / wood shredder fully reconditioned (workshop-reconditioned) Make: Rudnick & Enners Cjdpjzq Sqgofx Aizori Year of manufacture: 1990 Rudnick & Enners drum chipper, type TH-200/650/3 workshop-refurbished (fully reconditioned) with new bearings (spherical roller bearings) and tested rotor New blades and counter-blades Feed width/height: 650 x 200 mm Rotor diameter: 600 mm Screen mesh size: 50 x 50 mm Drive power: 75.0 kW Feed motors: 2 x 3.0 kW Weight: approx. 3,500 kg Machine colour: RAL 6011 Reseda green Without electrical installation and without control cabinet

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Crodpfxjt Tqy Ee Aizei Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Year of construction: 2005, condition: good (used), TMG roller row, roller conveyor 45cm wide, in several lengths, gravity or driven version. Roll: 40 x 450 mm bearing shaft. Track width: 500mm plus side guides Length: 0.7-4m lateral guide rail on request Meter price. Without drive: 150 euros With drive: 200 euros Crsdpegy Hapjfx Aizoi

Condition: excellent (used), Equalizer: shaft width 260mm length of table 900mm 3 knife shaft Planer: planing width 250mm dimensions of the table 250 x 600mm maximum planing height 130mm feed rate 8m/min Milling machine: Credpfx Aietur Epszji spindle diameter 30mm max tool diameter 90mm Saw: cutting height 80mm blade diameter 250mm Drill: drill diameter 3-16mm table dimensions 210 x 360mm