Used Lapping machines for sale (32)

Condition: used, Year of construction: 1983, table diameter 1000 mm workpiece height 25 mm number of wheels 1 total power requirement kW Csln Sx Ret Hw H Se Rsrb weight of the machine ca. t dimensions of the machine ca. m

Condition: good (used), Peter Wolters AC500 lapping machine TECHNICAL DATA AND SCOPE OF SUPPLY TECHNICAL DATA Rolling device size: 42 TS 7/14 Working disk diameter: 415 mm Ring width: 54 mm Working disk thickness: 50 mm Possible wear of the disks to approx.: 20 mm Number of rotor disks: 14 Drive data: 380 V / 50 Hz Upper disk drive: 1.0 / 1.4 kW Worm gear motor: 56 / 112 rpm Lower disk drive: 1.0 / 1.4 kW Worm gear motor: 500 / 100 rpm Workpiece drive: 0.5 / 0.7 / 0.9 kW 3-pole worm gear motor: 6 / 18 / 36 rpm Tilt arm drive: 0.25 kW Digital load adjustment of the upper work disk: 0-250 daN Connection data Electrical connection: 5.0 kW Crsljtxitvsn Sx R Reb Compressed air connection: 5-7 bar Compressed air consumption: Approx. 8 Nl/min OFFER SCOPE U.A: (list not exhaustive): Peter Wolters AC 500 lapping machine / fine grinding machine 1 inverter per motor documentation Exact scope of offer according to photo gallery No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: used, Year of construction: 2015, Technical details: min. workpiece diameter: 50 mm workpiece length: 500 mm Crslsudf E Non Sx R Rjb total power requirement: 60 kW horizontal stroke: 200 mm vertical stroke: 200 mm Balance shafts 1.1 Description of the basic machine concept - Horizontal end machining center for simultaneous end machining on both sides of wave-shaped parts - Cutting, centering, drilling, cross-drilling, chamfering, slot milling, etc. - Workpiece lengths up to approx. 500mm Machine base body and slide - Machine stand in compact design - Two three-axis modules with x, y and z axes, drives via AC servo motors and ball screws, linear guides size 45 Hydraulic unit - Mounted on the back of the machine - This means very good accessibility Central lubrication - Guides - Ball spindles (bearings and nuts) Tool carrier system - Right side of the machine: 2 x 6-fold crown turret - Left side of the machine: permanently installed motor spindle Electrical control cabinet - Authorized by VDE 0113 and EN 60204 Part 1 - 400V / 50Hz Machine paneling / work area - Machine is fully loaded - see the details of the revolver, motorspin and span - Work area lighting Machine painting - Textured paint, silky gloss - Machine cover light gray RAL 7035 - Work area doors and cladding frames blue RAL 5002 Tool carrier system, right side of the machine - 6-fold crown revolver, made by Hellmerich - Tool holder HSK63 - Max. Torque. 110Nm - Power max. 20kW - Nmax=8,600 rpm - Tool change 0.75 sec. - Chip-to-chip time 1.5 seconds. Motor spindle, left side of the machine - Tool holder HSK63 - Max. Torque. 150Nm - Power max. 20kW - Nmax=5,000 rpm *

Condition: good (used), LÄPPMASCHINE Hahn & Kolb LHD 0 Celn Sevdkvfox R Rsrb Machine from state institution/very well maintained -Lapping disk diameter 400mm -Max. Workpiece height 110mm -Max. Distance between the casting lapping disks 80mm -Speed range 40-80-160 rpm -Drehzahl-Antriebsmotor 700-1400-2800U/min -total power 1.8-2.7KW -Manually operated turning device -Original documentation -Well preserved original condition Dimensions: LxWxH 1.4x1.3x1.9 meters /Weight 1600Kg Errors / input errors excepted

Condition: used, TECHNICAL DETAILS Celn Sxjug U Dto R Rjrb - honing diameter : 1 - 12 [mm] - honing length : 40 [mm] - 2 honing heads - 1 control head - 1 deburring unit with multispindle head

Condition: used, TECHNICAL DETAILS - Plate diameter : 348 [mm] Crjln Ssug U Dmsx R Rsb - Part dimensions (rings) : approx. 70 [mm] - Part dimensions (full) : approx. 40 [mm] - Remaining work thickness : approx. 5 [mm] EQUIPMENT - Same as on photos

Condition: used, TECHNICAL DETAILS Crsljug U Dgen Sx R Reb - Plate diameter : 348 [mm] - Part dimensions (rings) : approx. 70 [mm] - Part dimensions (full) : approx. 40 [mm] - Remaining work thickness : approx. 5 [mm] EQUIPMENT - same as on photos