Used working platform semitrailers for sale (58)

Condition: new, maximum load weight: 37,350 kg, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis: * Welded construction made of high-quality steel profiles with continuous crossmembers for high ground and point load capacity, with a heavy-duty outer frame. * Loading platform at the rear as a steel welded structure with two welded-in tracks made of 5-hole steel sheet (hole pattern System Lohr/Rolfo) with a length of approximately 2,250 mm, hydraulically lowerable by approximately 350 mm. * Integrated loading platform at the rear of the vehicle, approximately 1,500 mm, hydraulically extendable as a steel welded structure with 5-hole steel sheet (hole pattern System Lohr/Rolfo) cover, light fitting, and 2 ramp compartments and ramp supports. * The drive and control of the rear section are provided by an electric hydraulic unit mounted in a stainless steel box on the left of the chassis, with a radio remote control. * Power supply via the vehicle battery of the towing vehicle. * NATO socket on the front wall, without connecting cable to the tractor unit. Fifth wheel coupling: * 2-inch kingpin, replaceable from below. Under-ride protection: * According to EC, permanently mounted. Support legs: * 2 x 12 t support winches with a 2-speed gearbox. Axles: * 3 x 10 t air-suspended axle unit, manufacturer SAF with disc brake approximately 370 x 45 mm, ABS, wheel connection 10-hole center-mounted ET120, total stroke of the air suspension approximately 200 mm, of which lifting approximately 140 mm and lowering approximately 60 mm, control of the air suspension via hand control with stop function. Steering axle: * 3rd axle as a trailing steering axle with manual and automatic reverse steering lock. Lift axle: * 1st axle automatically liftable, also switchable via operation on the chassis frame or via PIN 12 of the light socket. Tires: * 6 tires, 445/45R19.5, manufacturer of our choice, mounted on rim 14.00X19.5, 10-hole ET120. Fenders: * According to EC, 1/4 PVC fender in front of and behind the wheels of the 1st axle in front and behind, 2nd and 3rd axles in the rear. Tire chock holder: * None Braking system: * Two-line braking system according to EC with EBS, automatic load-dependent control. * Spring brake accumulator as parking brake acting on 2 axles, interlock-protected coupling heads permanently mounted on the front crossmember, without connecting line to the tractor unit. Manufacturer Wabco. Lighting system: * According to EC, 24 volts, multi-chamber rear lights, license plate lights, LED side marker lights, LED position light white in front and LED side marker lights at the rear, 15-pole socket and 2x7-pole sockets permanently mounted on the front crossmember, without connecting lines to the tractor unit. Load securing: Dwjdey Up S Sjpfx Aptsb * 9 pairs of folding lashing rings evenly distributed, tensile force approximately 8 tons. * 7 pairs of folding lashing rings evenly distributed, tensile force approximately 2.5 tons. * 2 pairs of folding lashing rings at the rear of the vehicle, tensile force approximately 2.5 tons. * In the outer frame, holes for lashing straps at approximately 500 mm intervals. Lashing stakes: * 16 lashing stakes approximately 100/40 mm, approximately 800 mm usable length. Lashing stake pockets: * 8 each on each side embedded in the outer frame. * 4 rows of stake pockets transverse to the loading area. Fl

Condition: used, maximum load weight: 36,040 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 03/2025, next inspection (TÜV): 05/2027, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis: * Regular ladder frame in lightweight steel construction with continuous crossmembers * With extended chassis frame * Coupling plate approx. 8 mm thick, with a 2-inch kingpin according to DIN 74080 / ISO 337 * Axle lift mechanism on axle 1 * Three-axle unit SAF INTRADISC, with disc brakes Ø 430 mm, offset 120 * Air suspension with approx. 180 mm travel Tires: * Wheels with internal sensors according to UN ECE R141 * Tires 6x 385/65 R 22.5 UNIROYAL TH 506, steel rims 22.5 x 11.75, offset approx. 120 mm * Chassis components: * Mechanical landing gear with leveling foot, approx. 24 t lifting capacity, single-sided operation on the right side * Storage box for: 10 side panels, folding stakes, and rear flap, completely enclosed, protected against spray water, and simultaneously serving as lateral protection * 2 plastic toolboxes, waterproof, dimensions (internal) approx. 545 x 400 x 400 mm, mounted at the rear, 1x left and 1x right Braking / Air Suspension System: * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS connector ISO 7638 (without connecting lines) * Parking brake as spring brake, external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 connector * WABCO EBS system * Air suspension system including 1 raising and lowering valve, mounted on the left side behind the axle unit * Driving position is automatically adjusted * 2 non-interchangeable coupling heads at the front ISO 1728 * Air tanks for braking system and air reserve made of steel (EN 286-2) Floor: * Plate floor approx. 30 mm thick, multiple-ply glued plywood * Floor sealed around the perimeter * Pocket for square tube inserts approx. 80 x 80 mm Front wall: * Storage for max. 14 square tube inserts approx. 80 x 80 (length 1,990 mm) on the inside of the front wall * Approx. 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame Djdpfey Trwujx Aptswb * 2 pairs of lashing points (permissible lashing force approx. 1,000 kg per ring) on the front wall according to EN 12640 * N o t e: When using the front wall for securing the load, suitable lashing straps must be used for tensioning if the vehicle is operated without side panels and a rear flap Rear wall: * ATTENTION: Hinge mount for folding rear wall 600 mm as well as stake mount for folding corner stakes at the rear, however, the folding rear wall and corner stakes at the rear are OMITTED. Side wall: * VarioFix steel outer frame, 4 pairs of stake mounts for folding stakes on the outer frame (evenly distributed), WITHOUT folding stakes, pair of lashing brackets in the outer frame (according to EN 12640), permissible tensile force approx. 5,000 kg per ring. Side panels: * ATTENTION: Hinge mount for 5 pairs of side panels on the outer frame as well as side panel stop mounted on the corner posts at the front, however, the 5 pairs of side panels are OMITTED. Electrical system / Electronics: * Lamp carrier made of steel, arranged above the underrun protection * KÖGEL LUXIMA Premium package, consisting of: LED license plate lighting, LED marker lights and reflectors at the front, flashing LED side marker lights, Superseal and bayonet connectors for the lights * 2 LED outline lights with pendulum bracket * 2 multi-chamber tail lights *

Condition: new, overall weight: 42,000 kg, axle configuration: 3 axles, total width: 2,550 mm, total height: 1,180 mm, Equipment: ABS, Availability: Immediately NEW VEHICLE Kässbohrer Platform Light MEGA SPS 3 Dedjvm Nm Iopfx Aptjwb # Empty weight 6,100 kg # Fifth wheel load 15,000 kg # Fifth wheel height: 980mm # BPW axles with disc brakes # 1st axle as lift axle # Jost support feet 24t # Wabco 4S/2M EBS with RSS # 2 x 7 and 1 x 15-pin electrical connections # 24V lighting system Aspöck # Tires 6 x 445/45 R19.5 branded tires on steel rims # 2 plastic wheel chocks Equipment: # 30 mm hardwood floor # Over-width device (4x over-width panels galvanized with LEDs + 1x rotating beacon) # 2 stainless steel tool boxes in the direction of travel right & left # 6x2 Jost container locks, retractable # Stake holder mounted on front wall + 20 stanchions (1500 mm) # 4 rows of stake pockets # 10 x 2 stake pockets in the frame # 7 x 2 lashing rings 4t on the platform 108 lashing points in the outer frame with 2t each # Side walls 600mm high & removable including depot under the vehicle # Chassis KTL coated and painted in RAL 3020 # Front wall RAL 3020 ----Errors, changes and prior sale reserved! Location: KTH-Trailer GmbH in Goch

Condition: new, overall weight: 43,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete range of vehicles, including immediately and soon available units, on our website. Equipment excerpt; full equipment details available on request. Chassis: * Welded construction made from high-quality steel profiles with through cross beams, designed for high point loads * Underrun bar width approx. 700 mm * Outer frame as UNP profile * Fifth wheel plate approx. 8mm * Neck height at front approx. 130 mm Coupling device * 2-inch kingpin Rear underrun protection * Bolted version, in compliance with EC regulations Side underrun protection * According to EC regulations, made of anodised aluminium profiles Landing legs * 2 x 12 t landing legs with compensating foot and single-side operation, RHS in direction of travel Axles * 3 x 9 t air suspension axle assemblies, disc brakes 22.5” * Total stroke approx. 180 mm * Lifting and lowering device via rotary slide valve Braking system * Twin-line compressed air braking system to EC specifications, with EBS and RSS, automatic load-dependent control * Spring chamber cylinders as parking brake * Polarity-protected coupling heads permanently mounted on front cross member, without connecting line to towing vehicle Tyres * 6 off, 385/55 R22.5 160J on steel rim 11.75 x 22.5 ET 120, brand of our choice * Tyre pressure monitoring system (TPMS) via EBS CAN bus Mudguards * According to EC regulations Spare wheel holder not included Load securing * 9 pairs of foldable lashing rings, evenly distributed, max. tensile force approx. 5.0 t * 9 pairs of foldable lashing rings, evenly distributed, max. tensile force approx. 2.0 t * Drill holes for attaching lashing straps every approx. 400–600 mm in the outer frame Front wall * Reinforced fixed steel structure, approx. 1,400 mm high * Inner face lined with approx. 9 mm phenolic plywood (approx. 1,250 mm high) Floor * Approx. 28 mm Z-hardwood floor let into the outer frame with galvanised omega steel profiles Lighting system * In compliance with EC, 24 volt, with multi-chamber lights * LED side marker lights * Front white LED position lights * Rear LED outline marker lights Dsdow U H Sbspfx Aptswb * Number plate lights * LED lane departure lights * 1x15- and 2x7-pin plug connections at the front cross member Equipment * 2 wheel chocks with holders * ECE 70 warning boards * Bracket for rotating beacon, incl. rotating beacon * 2 rubber buffers at the rear * Foldable and extendable access ladder at rear right (without platform) * 1 open perforated sheet metal box, transverse to direction of travel, approx. 600 x 450 x 2,430 mm, galvanised, behind the axles Paintwork * Front wall: RAL single colour as requested * Chassis: hot dip galvanised * Outer frame: hot dip galvanised + single RAL colour as requested * Centre stanchions: single RAL colour as requested * SSV: aluminium, anodised * Rear underrun protection: white (RAL 9016 traffic white) * Attachments: galvanised / KTL black * Rims: silver Conspicuity markings * Complete set in yellow Including special equipment * First axle liftable, with fully automatic, load-dependent lift control * 10 pairs of stanchion pockets in the outer frame, evenly distributed * 4 rows of stanchion pockets across the loading area * 20 stanchions made of galvanised tube 80/50, total length approx. 1,200 mm * Magazine for 20 removable stanchions inside the front wall * 5 x 25 side walls and rear wall made of anodised aluminium hollow profiles, foldable and removable * Removable Kinnegrip stanchions * Side wall and stanchi

Condition: new, maximum load weight: 39,070 kg, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Partial list of features. Full equipment details available upon request. Chassis: * Welded construction made of high-quality steel profiles with continuous profile cross-members, designed for high point loads * Outer frame as UNP profile * Fifth wheel plate approx. 8 mm, underride guard nose approx. 700 mm wide Coupling device: * 2-inch kingpin (also prepared for 3.5-inch) Underrun protection: * According to EC regulations, bolted design Side underrun protection: * According to EC regulations Landing gear: * 24 t landing legs with single-sided operation (approx. 66 t test load), Jost Modul CH (Heavy Duty) S-foot Axles: * 3 x 9 t air suspension axle units, brand SAF, with disc brakes approx. 430 x 45 mm, ABS, hub-piloted with 10-lug ET 120, total air suspension stroke approx. 200 mm (approx. 140 mm lift, approx. 60 mm lower), control via rotary slide valve with detent, with RTR function * Switch for second ride height (+ approx. 50 mm) on the holder of the lift/lowering device * Smartboard/TIM/Infocenter, without TPMS display Lift axle: * First axle liftable, with fully automatic load-dependent lift control, start aid via button in driver's cab (15-pin socket PIN12). Button in cab not included in delivery Brake system: * Two-line compressed air braking system according to EC regulations with EBS and RSS, automatic load-dependent control, spring actuators as parking brake, non-interchangeable coupling heads permanently mounted on the front cross beam, without connecting line to the tractor, brand Wabco Tyres: * 6 units, 385/65 R22.5 160J on 11.75 x 22.5 rims (brand at our discretion), ET 120 * Basic tyre pressure monitoring, connected to the CAN-bus system of the EBS * Tyre pressure monitoring display in driver's cab (prepared by the tractor manufacturer) Mudguards: * According to EC regulations, PVC mudguards (half-shells) over all axles * Anti-spray mud flaps Load securing: * 8 pairs of hook plates welded into the outer frame (traction approx. 3 t) * 6 pairs of lashing rings on the side of the outer frame, evenly distributed (traction approx. 10 t) Stake pockets/stakes: * 5 pairs of stake pockets recessed in the outer frame, approx. 90 x 90 x 4 mm * 3 pairs of stake pockets recessed in the loading floor, approx. 90 x 90 x 4 mm * 10 plug-in stakes made of galvanized square tubing, approx. 80 x 80 x 4 mm, with bottom stop Front wall: * Bolted front wall, approx. 1,200 mm high, metal plated Dodpfxjyz E T So Aptjwb Stake magazine: * Magazine for plug-in stakes inside the front wall Floor: * Approx. 28 mm hardwood floor recessed in the outer frame, with galvanized omega steel profiles Lighting system: * According to EC regulations, 24V with multi-chamber lights, LED side marker lights, LED position lights (white, front), LED outline marker lights (rear), license plate lights * 1x 15-pin and 2x 7-pin connectors on the front cross beam Equipment: * Warning sign according to ECE 70 * 2 LED work lights mounted on the lamp bracket (switched via reverse gear) * Bracket for rotating beacon at the rear (incl. beacon) * 1 foldable, extendable access ladder at the rear (without platform) * 2 stainless steel toolboxes, approx. 450 x 450 x 450 mm, in front of the front wall * Smart-Board with axle load display * 2 LED work lights above the front wall, switchable via chassis frame switch * 2 LED work lights at the height of the supports (switched via reverse ge

Condition: new, maximum load weight: 56,570 kg, overall weight: 66,500 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle stock, with vehicles available for immediate and short-term delivery, on our website. Extract from the equipment list. Full specification available on request. Chassis: * Chassis frame construction with welded longitudinal beams and through-running cross members * Rear underrun bar approximately 700 mm wide * Fifth wheel plate at least 8 mm thick, fitted between the longitudinal beams * Maximum cross member spacing 400 mm (for longitudinal floor installation) * 3.5-inch kingpin according to SAE standard, replaceable * Outer frame as UNP 200, open to the outside Landing Gears: * 24 t JOST - MODUL CH (Heavy Duty) telescopic landing gear with S-foot Axles: * 4 x 10 t SAF axles with large drum brakes * 22.5 single tires Dwjdpfx Aewx Dctoptob * Axle spacing approx. 1,700/1,810/1,810 mm * Air suspension unit with 10 t load capacity each, lift and lower device with 1 rotary valve Knorr/Wabco * Holder for lift and lower device, bolted design Braking system: * Smartboard/TIM/Infocenter at the lift/lower holder, additionally to the lift/lower valve, without battery (operable only with towing unit) * Mount for light and brake at the front underrun bar, total height approx. 700 mm * Basic version tire pressure monitoring, connected to CAN bus system of the EBS * With double-release valve for brake and spring brake actuator * Test port for brake cylinder pressure on the front right brake cylinder * 1 red and 1 yellow coupling head each * Lift and lower device mounted at rear left in driving direction * EBS braking system by Wabco, EBS diagnostic via CAN bus (EBS plug), no external diagnostic cable! Tyres: * 8 x 445/65 R 22.5 – premium brand of our choice * Centering rings Lubrication: * Grease nipple strips at the bogies and front steering, no central lubrication Superstructure: * Without body certificate according to DIN EN 12642 XL * 2x LED work lights on top of front wall (facing rear), switch at lift/lower holder * Front wall for platform design, heavy duty * Side outline marking yellow, rear yellow * Front wall approx. 800 mm high, with metal cladding, bolted Lighting: * 2x LED work lights fitted in lamp panel, controlled by reverse gear * 2x LED work lights, controlled by reverse gear, one each side near the landing gear * 2x LED reversing lights, one each side in front of first axle * Lighting/wiring system, brand of our choice * Number plate illumination * The towing vehicle must supply sufficient power for the selected lighting (especially reverse light) * Position lights front, bottom, white, one each side (LED) * 24 volt lighting system with large multifunction light * Flashing side marker lights (LED) * 1x 15-pin and 2x 7-pin connections at the front via multifunction box * EBS socket * 1 pair of lane marker lights (LED) Floor: * Hardwood floor approx. 28 mm thick, alternately with galvanized omega steel profiles Paint/Coating (no metallic finishes): * Chassis painted in RAL color of your choice, front wall (steel construction) in RAL color of choice * Axle hubs in chassis color * Axles and landing gear black * Wheels in aluminum/silver similar to RAL 9006 * Wheel nuts untreated * Underrun protection painted RAL 9010 pure white (aluminum) Accessories: * Lifting device for 1st axle * 9 lashing plates welded into the outer frame per side, lashing capacity max. 3,000 daN * 12 RUD-SLP lashing points per side with

Condition: new, maximum load weight: 32,155 kg, overall weight: 39,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete stock of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Chassis: * Welded construction made from high-quality steel profiles with thru-profile cross members. Designed for high point loads. Coupling device: * Fifth wheel plate with 2-inch kingpin Underrun protection: * According to EC regulations, bolted design Side guard: * According to EC regulations Landing legs: * 2 x 12 t landing legs with compensation foot and single-sided operation on the right in direction of travel Axles: * 3 x 9 t air suspension axle assembly, SAF brand, with disc brakes approx. 430 x 45 mm, wheel fixing mid-centered ET120, ABS, total air suspension lift approx. 180 mm, of which lift approx. 110 mm and lower approx. 70 mm * Air suspension operated via hand control valve with stop function Steering: * Last axle forcibly steered by linkage Axle lift: * First axle liftable, with fully automatic, load-dependent lift control Brake system: * Two-line compressed air brake system according to EC regulations with EBS and RSS, automatic load-dependent control, spring actuators as parking brake, anti-mix couplings fixed to front cross member, without connecting line to motor vehicle * Wabco brand Tyres: * Sixfold, 385/65 R22.5 160J on rim 11.75 x 22.5 ET 120 - brand at our discretion. Incl. tire pressure monitoring system, tire pressure display in cab (pre-installed by chassis manufacturer) Mudguards: * According to EC regulations, 1/4 PVC mudguards in front of and behind axle assembly Load securing: * 9 pairs of folding lashing rings, evenly distributed (tensile force approx. 8.0 t) * 8 pairs of folding lashing rings, evenly distributed (tensile force approx. 2.5 t) * Drilled holes in outer frame every approx. 500 mm for lashing straps (straps can be hooked in with closed drop sides, beveled outer frame) Stake pockets: * 10 pairs of stake pockets in the outer frame, evenly distributed * 4 rows of stake pockets across the loading platform * Plug-in stakes: 20 galvanised tubular stakes approx. 80/50 mm, total length approx. 1,000 mm * Magazine for 20 plug-in stakes on the inside of the front wall Front bulkhead: Dsdey Auhzjpfx Aptjwb * Reinforced steel bulkhead, fixed, interior covered with approx. 9 mm phenolic plywood floor (approx. 1,250 mm high) Floor: * Approx. 28 mm Z-hardwood floor, recessed into the outer frame Side walls: * 4 x 250 mm side walls and rear wall made of anodised aluminium hollow sections, foldable and removable, removable Kinnegrip stakes * Side wall and stake magazine under the chassis * Left and right insertion rails for side walls and stakes Lighting system: * According to EC regulations, 24 Volt with multi-chamber lights, LED side marker lights, LED position lights front white, LED outline marker lights at rear, license plate lights * 1x 15-pin and 2x 7-pin plug sockets on front cross member Equipment: * Two wheel chocks with holders * Warning signs according to ECE 70 * Work spotlight on lamp bracket (operated via reverse gear) * Holder for rotating beacon at rear, incl. beacon * 2 x stainless steel toolboxes, approx. 600 x 500 x 500 mm Paintwork: * Chassis and front bulkhead sandblasted, primed and coated in a single colour * Chassis: hot-dip galvanised + RAL colour of choice * Front bulkhead: RAL colour of choice * Side walls: anodised aluminium * Top stakes front bulkhead: hot-dip galvanised * Hubs: KTL blac

Condition: new, maximum load weight: 52,810 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Cargo area: * Cargo area with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing legs: * Hydraulic landing legs TPMS: * TPMS tire pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor must be capable of transmitting and displaying these data. Axles and suspension: * BPW axles, technical capacity 12,000 kg each, first axle fixed, all others hydro-mechanically forced-steered, mounted on turntables * Air-suspended with lift and lower valve * Axle toolkit Dodpexttc Aefx Aptjwb Tires: * Tires 445/65 R 22.5 169 K Electrical system: * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * Connections according to standards. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield point 355MPa), S690QL/S700MC (yield point 690MPa) Painting: * Complete steel structure automatically shot-blasted after welding using a shot-blasting machine * Secondary blasting with corundum for optimal adhesion of the coating system * Final painting with 2 coats of 2K topcoat, single color in RAL 1007 Narcissus Yellow according to RAL system 841GL * Rear section metallized and painted in RAL 9010 Pure White * Wheels in Silver Grey * Paint structure tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Including accessories: * Cargo area with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection strip * On the gooseneck and rear panel left and right, each with a bracket for warning signs including socket * Rear steering from the front and rear by cable remote control via push buttons, with single-track control of the axles (without installation in the tractor unit) * Electro-hydraulic unit * 12 pairs of stake pockets for approx. 100 x 50 mm stakes in the outer frame of the cargo area * Load manometer for determining axle loads including load diagram * Lift axle on the front axle, controlled by TEBS E * 5 pairs of crosswise stake pocket rails on the cargo area, for approx. 100 x 50 mm stakes * One INOX toolbox 1,200 x 460 x 550 mm mounted at the front left under the cargo area (in direction of travel) * 1 shunting coupling with reinforcement bolted to the rear cross member * BEKAMAX (Pico) automatic central lubrication system with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum)