Pellet press

CPM 2000

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Nedpewp Rqfefx Akfswf Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 10014777, overall weight: 1,300 kg, load capacity: 210 kg, arm reach: 2,696 mm, We offer industrial robots from the manufacturer KUKA. The scope of delivery includes the robot arm, control cabinet and the associated cables. The robots come from a functioning system and have been professionally dismantled. We carry out a functional test and check the robots. If you are interested, we offer the opportunity to demonstrate the functions to ensure that they meet your requirements. - Supplement at additional cost - We are pleased to be able to offer you a new function for our robots: The Siemens S7-1200 Profisafe safety controller. With this controller, you can easily integrate an emergency stop function, a safety gate and a start-stop connection via the Profisafebus. The controller is fully configured and programmed so that you can implement a simple stand-alone solution with a robot and a safety fence. If required, we can also offer you additional support during commissioning. Nwodpfx Aoq Suwbekfjf We grant a 14-day right of return. Further warranty services are excluded. We have an extensive stock of these robots and the prices quoted are package prices. Discounts are negotiable for larger order quantities. We invite you to contact us again to discuss further details. Sale exclusively to traders.

Year of construction: 2001, operating hours: 123 h, condition: ready for operation (used), machine/vehicle number: 123, Metal silo for storage of woodchips, etc. Technical description: silo DM: 5m Height: 8 m with outfeeding unit (screw conveyor connection to output) Nwedpfx Aeftdv Uekfof Cappacity: 42 m3 With outfeeding transport screw conveyor to the top of the silo building. Already dismountled, visit possible by appointment at our warehouse H-2013 Pomáz/Hungary.

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters Nwodpfx Akeu Hmacefof 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. Nsdedfgg Ispfx Akfjwf B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, CNC Turning and Milling Center - DMG GILDEMEISTER - CTX gamma 1250 TC YOM: 2009, until 2011 showroom machine, from 2012 operating The machine can be inspected by appointment in the factory under power. Condition: Good (high accuracy), ready for immediate use. Spindle hours (August 1st, 2025): 9.580 h The heart of the machine is the integrated traveling column with turning milling spindle and interpolating B-axis. Machine basic data: Nedpfx Aow Hg Nlskfjwf * Part hollow clamping device (hydraulic) * C-axis * Cross slide above with turning/milling spindle as motor spindle, with hydraulic clamping in turning, tool holder: Capto C6 * Y-axis: +/- 200 mm * B-axis: +/- 120° * Disc-type tool magazine * Absolute, direct measuring systems in X-, Y-, Z1-axis * USB-interface, Ethernet interface TECHNICAL SPECIFICATIONS: * Control: Heidenhain CNC Pilot 4290, 3-D path control TURN PLUS Working area: * Swing diameter over bed: 630 mm * Turning diameter: 630 mm * Spindle distance: 1.510 mm * Bar diameter max.: 65 mm Main drive I: * Drive power (100% / 40% ED): 24 / 34 kW * Speed range from - up to: - 5.000 rpm * Speed of the C-axis: - 5.000 rpm Turning/milling spindle: * Tool holder: Capto C6 * Spindle speed: - 12.000 rpm * Drive power (100% / 40% ED): 13.2 / 22 kW * Torque (100% / 40% ED): 60 / 100 Nm Tool magazine: * Number of tools: 36 * Dimensions of the machine approx. (Width/Depth/Height): 6.860 x 4.220 x 2.530 mm * Total weight of the machine approx.: 18,5 tons EQUIPMENT: * Well equipped … * No steady rest available * Documentation complete available. Detailed technical data sheet and information on equipment available on request. There is no guarantee for correctness and completeness of the technical details and and accessories.

Condition: good (used), Manufacturer: Haver & Boecker Documentation available Mechanical conversion from 50 kg to 25 kg bags in 1999 Control system: Siemens S7 Nwedjv Sz Tdspfx Akfef Upgraded to the latest standard with spare parts support in 2015 Supported bag types: Quicklime, hydrated lime, cement, gypsum

Condition: used, Year of construction: 2004, Hydr. reversing Bale size 0.8 - 180 m / Nwjdjrxta Espfx Akfof

Year of construction: 2002, condition: good (used), functionality: fully functional, Drum dryer for wood sawdust and chips with capacity up to 15t/h. Nwedpfx Akjvx S Hnsfjf Condition - fully functional.

Year of construction: 1999, condition: used, System: Used decanter / centrifuge Manufacturer: Baker & Hughes Model: full coat screw centrifuge Type: CP 3054 Year of construction: 1999 Nodpfjcbukrex Akfswf Hoechstzul. Speed: 3132 I/min Inner diameter drum: 552 mm Drum wall thickness: 14.5 mm Engine: 2 electric motors, new Auger motor Control Panel: no Frequency converter: Yes Documentation: Yes Maintenance: regularly twice a year In operation: By early 2015 Buying and renting possible.