Panel sizing circular saws

MARTIN T 73 Automatic

Condition: used, Year of construction: 2006, Motor-adjustable parallel guide; length stop with display; single-sided motorized tilting; sliding carriage, 3000 mm; 5.5 kW; scoring cutter; cutting width 1000 mm. Ljdpfx Aiszawiuj Horr Location: Nattheim.

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: Lsdpeqt Dmysfx Ai Horr - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: ready for operation (used), Year of construction: 2002, machine/vehicle number: V 435496, functionality: fully functional, cutting height (max.): 170 mm, cutting width (max.): 1,100 mm, cutting length (max.): 3,700 mm, length stop: 3,200 mm, Equipment: scorer, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. cutting length: 3,700 mm Max. cutting width: 1,100 mm Cutting width at rip fence: 1,100 mm Max. cutting height: 170 mm Max. cutting height with scorer: 170 mm Saw blade diameter: 450 mm Length stop: 3,200 mm Sliding table length: 3,700 mm Sliding table width: 450 mm MACHINE DETAILS Total weight: 1,800 kg Connected load: 7.5 kW (10.20 HP) Extraction port diameter: 120 mm EQUIPMENT Motor brake Scorer unit Digital cross table Digital length stop Ljdpfex Dkp Ijx Ai Hsrr 3-axis electric scorer unit 400 mm adjustable hood arm 3.70 m edging length Laser cut line indicator Template holder Pneumatic folding circular saw fence Second support

Condition: new, Year of construction: 2026, ♻ Universal use (diverse wood, pallets with nails and pins, particle boards, waste and scraps, veneer, MDF plates, cardboard boxes, plastics, textile etc.) ♻ A shredding system integrated with a conveyor and magnetic separator offers a comprehensive solution for material processing and purification. Lrsdstpvdhspfx Ai Hor ♻ The system consists of a powerful shredder capable of breaking down various materials, a conveyor which helps to evenly distribute the shredded material, ensuring a steady flow for further processing or disposal and a magnetic separator that efficiently removes ferrous or magnetic particles from the mixture, enhancing material purity and preventing equipment damage. Technical data: Shredder: ✔ Power: 22 kW ✔ Shaft length: 650 mm ✔ Shaft diameter: 270 mm ✔ Shaft RPM: 80-120 rpm ✔ Number of cutting knives: 28 ✔ Granulation: 10-50 mm ✔ Capacity: up to 5 m3/h* ✔ Filling opening: 1446 x 1342 mm ✔ Weight: 1750 kg Z conveyor: ✔ Frequency converter (adjustment of conveyor speed) ✔ Overband magnetic separator ✔ Length: 6500 mm ✔ Width: 350 mm ✔ Capacity: 0,5 kg/s ✔ Power 0,25 kW ✔ Transport wheels 1 years warranty or 1000 working hours

Condition: excellent (used), Year of construction: 2010, Altendorf F45 Elmo 3-axis control Carriage length: 3200 mm Cutting width at rip fence: 1300 mm Scoring unit: Prepared Saw blade height adjustment: electric / position control Saw blade tilt adjustment: electric / position control Rip fence: electric / position control Crosscut fence adjustment: manual Saw blade angle display: digital readout Cutting height display: digital readout Ljdpfxsy Sbvkj Ai Hjrr Crosscut fence with mitre function: yes Saw blade diameter: 450 mm Speeds: 4 Motor power: 5.5 kW Extraction port: 80 and 120 mm Duplex mitre fence Year of manufacture: 2010 Price: 15,500.-

Condition: used, machine/vehicle number: 008272, Position 1: 5 Axis CNC Routers BIESSE + KUKA-ROVER A + KR210 R3100 Position 2: Robot BIESSE + KUKA-ROVER A + KR210 R3100 Lrsdjx A Tfvjpfx Ai Hor

Condition: excellent (used), Year of construction: 2000, Diemer residual wood shear ASC 65 - 25 Infeed dimensions 650mm x 250mm Lrodpfxswu Nwns Ai Hor with infeed vibrating trough

Condition: excellent (used), FLEXIBLE SYSTEM OF SINGLE-SIDE EDGEBANDING (BATCH ONE) Ljdpfx Aeinigmei Herr Composed of the following machines: M.01) PANELS HANDLING and RETURN SYSTEM Mod. PROFI TBR100/20/30/F M.02) SINGLE-SIDE EDGE BANDER (RIGHT-HAND machine)"HOMAG" Mod. Profi KAR350/12/A Panels thickness (min/max) mm 8 / 60 - Working width (min/max) mm 200 / 1200 Numerical Control / Software PC 22 Adjustable feeding speed (m/min ) 18 - 32 Panels in-feed system WZ 14/30 Pre-milling Unit (vertical joint trimmers) adjustable by N.C. (2 x Kw 3) DOUBLE Glueing Unit (P.U.R. Glue + Quick Melt unit) 2 x PU 34 Pressure zone (N.C. adjustment) - Edge coils supporting unit (No. 12 reels) Snipping (end-cutting) unit WK13 Rough Trimming unit (2 x Kw 055) Fine Trimming unit (Multi-profile, adjustable by N.C.) MF 21 (2 x Kw 0,55) Corner Rounding unit (Contour Trimming) FF 32 (4 x Kw 0,4) Multi-Profile Copying unit adjustable by N.C.(fine and contour trimming) FK 31 (30 m/min) recently added (in a technological "revamping" operation) Profile Scraping unit (Multi-profile, adjustable by N.C.) MN 21 (servo) Finish processing unit (Glue scraper + Buffing unit) FA 11 Jumping Milling grooving unit UF 11 (1 x Kw 4) M.03 ) PORTAL BRIDGE (UNLOADING/LOADING) "BARGSTEDT" Model. TFU200/L/30/12/S

Condition: excellent (used), Year of construction: 2000, Robust pivoting milling machine T 26, pivotable from -45 to +45 degrees. Reversible drive motor 5 / 6kW with automatic motor brake. R/L rotation. Pivot angle from -45 to +45 degrees, electrically adjustable. Height adjustment max. 150mm, electrically adjustable. When the height is adjusted, the correction factor for the pivot angle is displayed in the upper display, which can then be set on the stop, thus allowing settings to be implemented according to drawings. Four speeds: 3000, 4500, 6000 and 9,000 rpm. Spindle diameter 30mm, quick-change spindle with torque wrench. Comfort stop T226 with digital displays for total adjustment and infeed fence separately, as well as input of the cutter diameter, whereby the cutting depth is calculated automatically. Stop with lifting device, pivotable to the side (for curved milling). Table extension on the right and left with extendable workpiece support. Support can be extended by 700mm. Table length approx. 2400mm. Folding stop for mortise milling. Lodpfxozbm Tfj Ai Hjrr Workpiece clamping device Aigner Centrex. Original Martin cast iron fence, left 500mm, right 500mm with two insert strips. 3-roller feed HolzHer ET117, with 8 speeds, R/L rotation, new rollers. Feed socket, switchable from the control unit. Comfort stand with electrically height-adjustable feed support, which can be pivoted to the side for machine maintenance and then easily locked into place. Dust extraction nozzle 2 x 120mm. Compressed air connection 6 bar. Emergency stop switch. Some parts of the machine have been newly painted (special color RAL1015). V-belts renewed. Operating manual. CE marking. Dimensions approx. 3000 x 1500 x 1830mm (LxWxH). Weight approx. 1800kg. The machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration and are in our warehouse, see "other offers from this provider".

Condition: used, Year of construction: 2011, Used Equipment Year of Manufacture: 2011 Lodpfx Aozvz Tbei Hsrr Condition: Currently installed Equipment and Technical Data: -Filter housing base ring NFHSU 9/9 with discharge chute for press - Discharge: 1.1 kW - Storage volume in the base ring approx.: 3.25 m³ - Dimensions L x W x H (incl. base ring) 2440 x 2440 x 900 mm - Ground clearance: 350 mm - Conveyor screw for briquetting press 0.75 kW - Extension and expansion rings are optional; max. storage volume approx. 12 m³ - Extension and injection ring NFHSU for 9/9 and 10/10 Jet, L x W x H: 2480 x 2480 x 500 mm - Expansion ring for NFHSU 9/9, 2480x2480x700 mm, with inspection door and type-tested explosion flap - Filter for filter housing NFHSU 9/9/20, filter area 116 m²: The Nestro filter system NFHSU is a solid filter construction made of 4 mm galvanized steel sheet and is designed for outdoor installation and weather resistance. This filter system is particularly robust and designed for underpressure operation up to -3,500 Pa. The filter system is equipped with upper and lower inspection doors 600 x 600 mm, with automatic filter regeneration, dry extinguishing system, differential pressure switch / volumetric flow monitoring and the necessary explosion protection. Note: Filter is equipped with high-quality filter material, BIA category M, antistatic, residual dust content < 0.1 mg/m³ and suitable for return air operation. Further technical data: - Filter tube length: 2,000 mm - Filter tube diameter: 230 mm - Number of filter tubes: 81 - Filter area: 116.0 m² - Filter regeneration: automatic/motorized - Number of vibrating motors: 4 pcs - Fan shroud for NFHSU 9/9 including inspection door - Fan US-FHN (clean gas) 22 kW 16,400 m³/h - 3,200 Pa: A Nestro high-performance fan with above-average efficiency and high energy saving potential when using a frequency inverter (optional). The robust welded construction is primed and painted in RAL 5015. The fan is delivered as standard with an inlet cone and backflow damper. Technical data at a glance: - Volumetric flow: 16,400 m³/h - Corresponding underpressure: 3,200 Pa - Electric motor: 22 kW / 400 Volt / 50 Hz - Speed: 3,000 rpm - Design: B5 - Pressure nozzle: without - Application area: Nestro underpressure filter and others - Injection nozzle d= 400 mm with flange ring - Injection nozzle d= 350 mm with flange ring - Backflow damper d= 350 mm with flange edge - Backflow damper d= 400 mm with flange edge - Briquetting press C150; 30 - 50 kg/h, hydraulic unit 5.5: Technical data: - Power consumption (hydraulics): 5.5 kW - Briquette diameter: 50 mm - Weight: 650 kg - Briquetting performance with a bulk density of approx. 250 kg/m³, material-dependent: 30 - 50 kg/h - Ground clearance with base frame (art. no. 710300): 350 mm - Briquetting press, dust-proof - Briquetting press complete with hydraulic solenoid valve control for automatic operation, oil tank with 100 l oil, in welded construction, including main cylinder, stuffing cylinder, gripper cylinder, pressing jaw, electrical control panel with fully automatic control and 5 m cable The press is standardly equipped with: Monitoring switch for oil temperature, hardened press bushing, connection part for briquette line and automatic briquette length adjustment