Used Binding Press for sale (15,468)

Condition: good (used), Schmedt PraLeg XL 18-60 Case in machine + Schmedt PraForm 21-50 Press Manufactured in 2022. Schmedt PraLeg XL 18-60 Book Hanger Machine in good condition, ready to operate. The machine hangs a book block into a prepared hardcover. Two gluers, smooth glue thickness adjustment. Format: Block height: 80 – 450 mm Block width: 110 – 450 mm Block thickness: 2 – 80 mm Production rate: approx. 200 – 300 pcs/h Power supply: 230V Weight: 300 kg Made in Germany. Nlsdpfxozt Iaio Ahnef Schmedt PraForm 21-50 Book Press Book press with groove cutter. Made in Schmedt, Germany. The machine is in very good condition, ready for production. Technical specifications: Maximum format: 420 x 520 x 100 mm Weight: 220 kg Power supply: 230 V + compressed air. Price is for a set of two machines.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Nedpfozuzw Dox Ahnelf Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: good (used), Proofing press 55x65cm Antique Nledpfxoztn Slo Ahnsf The machine is in very good condition, can be used as an exhibit or as a printing machine. Max. format 550×650 mm Weight 650 kg Flow table, system of claws holding the sheet. Electrically driven spreading roller.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm Nedpfjzuzwkox Ahnelf - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Year of construction: 2013, condition: used, Membrane press table Njdpfezuz Ehsx Ahnolf Manufacturer: Columbus Type: Vacuum forming Year of manufacture: 2013 Technical data - Working area: 1980 x 1350 - Must be connected to an external vacuum pump Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2012, condition: used, Membrane press Manufacturer: Columbus Nlsdpfx Aozuz Ebjhnsf Type: Vakuform Sonder Year of manufacture: 2012 Technical data - Must be connected to an external vacuum pump - 750 watts, 230/380V, 50 Hz - Boiler capacity: 200 l - Suction capacity: 25 m3/h - Vacuum: max. 0.85 bar - Working area: 2000 x 1350 mm Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2015, condition: used, Membrane press Manufacturer: Columbus Type: Multimat Year of manufacture: 2015 Technical data - Press table: 3000 x 1400 mm MULTIMAT - Membrane press table Mobile table with a pivoting heating hood and membrane frame High-performance vacuum pump TF 40, final pressure adjustable up to a maximum of 900 mb (9 t/m²) Pneumatically pivoting film fixing frame Usable membrane frame incl. highly elastic silicone membrane (700% elongation) Aluminum heating hood, fully insulated, continuously adjustable from 0 to 140 °C Digital differential pressure control Entire system (incl. vacuum pump) maintenance-free Electrical connection (incl. heating hood): 10 kW, 400 V, 50/60 Hz Dimensions: External dimensions: 3200 mm x 1600 mm Usable area (without membrane frame): 2800 mm x 1200 mm Usable area (with membrane frame): 2750 mm x 1150 mm Njdpfozu Ammjx Ahnslf Table / working height: 900 mm Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Year of construction: 2013, condition: used, - Press table: 3000 x 1400 mm Membrane press Manufacturer: Columbus Type: Multimat Year of manufacture: 2013 Technical data Nsdszuz A Tjpfx Ahnslf - Press table: 3000 x 1400 mm Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Nledpfxezuzwwo Ahnef Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: good (used), functionality: fully functional, Very robust and heavy-duty mechanical knee-lever press made of cast iron. Converted to electric heating, 230V/50Hz. Approx. 850 kg. Pressing area: 40x45 cm. Nedpfezuwv Njx Ahnolf

Year of construction: 1997, condition: used, Baling press Manufacturer: HSM Type: HSM 75 VL Nljdpfozuz Dwex Ahnjf Year of manufacture: 1997 Technical data: - 2.2 kW motor - 9 t pressing force - 400 V / 50 Hz Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2013, condition: used, Membrane press Manufacturer: Columbus Type: Vacuum forming Year of manufacture: 2013 Technical data - Working area: 1980 x 1350 Note: Nledpozu Amysfx Ahnof The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. Nlodpezuzv Tofx Ahnjf The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Continuous press Nledjzuzxbepfx Ahnef Manufacturer: Ligmatech Type: Optimat MDE 10 Year of manufacture: 2001 Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each - Pressing takes place centered and on a zero line on the operator side Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 1996, condition: used, Baling press Manufacturer: HSM Type: 55.1VL Year of manufacture: 1996 Technical data - 4.0 kW motor - 18 t pressing force - 400 V / 50 Hz Nljdozuz D Rspfx Ahnof Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Nsdpfxjzuzvme Ahnolf Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Nledpfxszuzi To Ahnef Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, HYDRAULIC PRESS SMG PRESSURE 300t Nljdpjtndu Ujfx Ahnof LENGHT OF STROKE 700mm POWER 30kw UP TABLE DIMENSIONS 1500(1600)x1300mm DOWN TABLE DIMENSIONS 1500(1600)x1300mm CUSHION 100t CUSHION LENGTH OF STROKE 280mm WEIGHT 28.000kgr FULL RECONDITION LIKE NEW CHANGE EVERYTHING (SEALS PUMPS etc)

Condition: used, Year of construction: 2007, Heating plate press Manufacturer: OTT Type: Solid 16-32 Nlsdozuzxnopfx Ahnof Year of manufacture: 2007 Technical data Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2025, total length: 1,200 mm, total width: 800 mm, total height: 1,800 mm, Colour: Blue Empty weight: 450 kg Price: On request - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: PB12093N2025005 - Operating hours: 0 - Drive system: Conventional - Vertical/Horizontal: Horizontal and vertical Nlodpfx Ahoztxn Rjnef - Number of rolls [pcs.]: 3 - Power [kW]: 1.5 - Shaft diameter [mm]: 50 - Top roll diameter [mm]: 155 - Bottom roll diameter [mm]: 155 - Bending speed [mm/min]: 11 - Capacity diameter round [mm]: 50 - Options: Digital readout - Transport dimensions: 1200mm x 800mm x 1800mm (l x w x h) - Transport weight [kg]: 450kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), For sale: a professional Constantin Hang Maschinenfabrik Göppingen bookbinding machine, model 167-11, manufactured in Germany. The machine is mounted on a large work table and equipped with a pneumatic control system and a foot pedal, allowing for convenient operation during use. Hang machines of this type were designed for professional bookbinding and production work. The design allows for easy handling and positioning of large sheets and other materials being processed. Specifications: Manufacturer: Constantin Hang Maschinenfabrik Njdpfx Ahezudblenolf Model/Type: 167-11 Serial Number: 37886 Country of Manufacture: Germany Control: Pneumatic Operation: Foot Pedal Design: Stand-alone machine with work table Application: Bookbinding / Printing industry The machine is sold with the large work table shown in the pictures. Used condition. Shows normal signs of wear and tear appropriate for the age of the machine. The visual condition is consistent with the pictures. Made in Germany.

Condition: excellent (used), Year of construction: 2021, operating hours: 1,118 h, functionality: fully functional, HSM baling press, type HL 7009 ST/A, year of manufacture 2021 Technical data: Manufacturer: HSM Nledpfx Ajzvluvshnsf Type: HL 7009 ST/A Year of manufacture: 2021 Operating hours: 1118 Pressing force: 70 t Specific pressing force: 58 N/cm² Drive power: 11 kW Feed opening: 1020 x 900 mm Bale size: 1100 x 1100 mm (W x H x D) Bale weight: up to 600 kg Tying: 4-way horizontal, manual Machine dimensions: 5992 x 2066 x 2394 mm (L x W x H) Weight: 7500 kg Materials: Paper, cardboard, film Note: The press is in good condition and has been inspected and tested by us. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against prepayment, ex works, without any warranty.

Condition: used, functionality: fully functional, machine/vehicle number: 3910010947, counter reading (black): 33,10,691, With this offer, you are purchasing a second-hand colour production system, the “Xerox Versant 4100 Press” Items for sale: 1 x Xerox Versant 4100 Press with the following specifications: incl. Paper Deck A-CF03/A-CF04 incl. Finisher A-GW04/A-GW07 Includes Stacker LCS-1 Includes SquareFold Not the right configuration? It’s no problem to configure the machine to your requirements. Please feel free to contact us! Meter readings: Total: Approx. 9,571,697 pages Colour: Approx. 8,874,258 pages Black: Approx. 697,439 pages Condition: Nlodpfx Ahszmpbnsnjf This is a second-hand machine, which may show signs of wear (minor scratches or yellowing). The machine has been tested for functionality A test print can be seen in the photo Packaging and dispatch: You are welcome to view the device during our opening hours. Please arrange an appointment to do so! Sea-worthy packaging and worldwide dispatch available on request! A functional test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: good (used), Kolbus VDB Cover bender This machine is in very good condition and ready to use. Manufactured by Kolbus, Germany. The pressure rollers feature smooth adjustment of the gap and cover straightening power. The entire unit is mounted on a convenient base with wheels. Working width: 750 mm Nljdpjzt H Ufsfx Ahnef Power supply: 380V Weight: 150 kg

Year of construction: 2018, condition: used, - Heating plate format (mm): 2850 x 1550 - Total pressing force (kN): 2400 - Maximum operating temperature: 180 degrees Celsius Vacuum press with 3 paternoster magazines Manufacturer: Wemhöner Type: Variopress - Basic 1000S Year of manufacture: 2018 Technical data Heating plate format (mm) 2850 x 1550 Design of the electric heating plate: Aluminum heating plate on top Total pressing force (kN) 2400 Maximum chamber pressure (bar) 6 Nedpfszuz Euex Ahnelf Maximum operating temperature 180 degrees Celsius Maximum batch or workpiece size (mm) approx. 2460 x 1180 Thermoplastic film as roll stock, film width: approx. 1430 mm Film thickness (mm) approx. 0.25 - 1 Chamber height (mm) max. up to 180 Connection values: Installed power (kW) approx. 46 Required air pressure (bar) approx. 8 Including 3 x paternoster magazines for film rolls Note: The technical data and descriptions are a copy of the order confirmation from that time. The data is for informational purposes only and is not binding.