Used Boston Wire Stitcher for sale (2,952)

Condition: good (used), Introma ZD-2S wire stitcher Machine in very good condition. Ready to work. This is the currently produced model. Technical data: performance: 180/min sewing thickness: max 25mm wire diameter: max 1mm Power supply: 380V Weight: 230kg The machine has an adjustable table for block and booklet sewing. Front margin. Instructions included. Oelgdx0Nc Safety housings. Operating mode selector.

Year of construction: 2006, Condition: used, Ultrasonic and electrolyte cleaning, wire cleaning line, wire cleaning plant, wire treatment plant Manufacturer: Sirio-Wire Type: M0209 Number of wires / cores: 12 (6+6) Wire thickness: 1,0 - 5,5 mm; but also stronger wires were run over the line and the achieved cleaning result was very satisfying. Year of construction: 2006 The plant was only in operation for about three years, then the production was moved to another location. Process: Ultrasonic and electolytic cleaning in a hot bath. On the manufacturer's website siriowire you will find a detailed description of the process under "Ultrasonic and Electolytic Cleaning". The unit is in good working condition and is complete except for the pumps. Vtp7Q3 On the photos the catwalk for the operator and the collecting basin in which the plant stands are missing, these photos are still supplemented. On the last three photos you can see plants of this design in operation.

Condition: new, Year of construction: 2024, PROFESSIONAL WIRE FEEDER WITH AC SERVO MOTOR FOR LASER AND TIG WELDING Citronix professional wire feeder with servo technology - means that it uses ac servo motor for motor drive, which enables it not only to feed wire very precisely even when the speed is low, but also the ability to set the length in „mm“ for wire withdrawal, and also, after the material is cooled down, we can push it again (the smallest step 0,1 mm) This is a very important feat with laser welding, and this working method is an advantage compared to wire feeders made in the Far East, since with those machines the function of withdrawal and pushing the wire is set on time, and the consequence of this method is that the tip of the welding wire never comes back to the place where the withdrawal started. We made the Citronix wire feeder in a way that it can control not only the wire feeding process, but it can also manage (turn on and off) both the laser source and the gas magnetic valve. This is another significant difference and advantage compared to other manufacturers, because usually there is no spot welding technology in laser welding machines, so if someone wants to weld sheets in the spot welding technology, he can set the spot time and the wire feeder will control the laser source. Wire feeder has 4 operation technologies: 1. continuous welding with wire feeding; 2. continuous welding without wire feeding; 3. spot welding without wire feeding; 4. intermittent welding with wire feeding – like with the TIG manual welding when you add manually electrode drop-after-drop. Cgz07Mnafj Wire feeder has 200 memory cells – locations, if the parameters are set, they can be saved on the memory location and we can name them in any number or text combination, in order to make use easier. We also developed a foot pedal, which can be attached to the wire feeder and regulate the feeding speed. It works like a gas pedal in motor vehicles. If, for example, we set the maximal speed 10 meter per minute on the display, and press the pedal all the way, the speed will be 10 meter per minute (or the speed we set), if pressed only half way, the speed will be half of the set speed. This feat can be used if the operator remains in one place, for example if he is sitting. If this pedal isn't necessary, the wire feeder can be attached to the system in a manner to turn on-off the welding process from the button on the torch. This pedal is optional, and in case you want to order it, it is additionally charged 400 EUR. Take a look at the monitor images and see the functions – parameters that can be adjusted. Citronix wire feeder can be used not only for laser welding, but also for the TIG welding, we made a filter to prevent HF-spark. Wire thickness it can push is from 0,8-2,4 mm. At this moment, we have a menu in English, German, Hungarian, and Serbian language.

Condition: used, Module converter, electronic module -Wire type: DSV 5421-10/220 -Module: 220 V/4 KVA/10 A Bg0Wntxmf9 -with: controller BELIMO SGS -Dimensions: 275/275/H225 mm -Weight: 9.7 kg

Condition: used, Module converter, electronic module Yscxb0 -Wire type: DSV 5421-10/220 -Module: 220 V/4 KVA/10 A -Dimensions: 275/275/H225 mm -Weight: 8.1 kg

Condition: used, Servo motor, electric motor, DC motor, stepper motor, stepper motor, stepping motor -Manufacturer: Scharmann, DC motor with tachometer dynamo and cooling fan -Engine: Type GLF 100/13 -Voltage: 170/200V -Power: 6.5 kW -Speed: 3000 rpm -Tachometer dynamo: Hübner TDP 0.2 T-4 60V 1000/max. 9000 rpm -technical Data: see photo of nameplate -Shaft: Ø 28 x 45 mm -Design: B5 Bjnbz08Stf8 -Dimensions: 640/250/H390 mm -Weight: 57 kg

Condition: excellent (used), Year of construction: 2015, Ref:10864 . 2015 Horizon SPF-200A Collator/Stitcher. Excellent condition, with separate rear collation possible. Collator comprising: 20stn. - 2 x VAC-1000 c & a 10 bin tower suction collators with touch-screen control, double- and miss-sheet control • 2 x EAB-100 extra-air blowers • 10.4” icon-based 200 job memory colour touch-screen • Advanced programming functions e.g. double cycle, dual cover feed • Memorises frequent jobs • Wireless remote-control unit • Simple, fast set-ups by non-specialist finishing operators • Make-ready in seconds, next-to-no-waste • Works from flat-sheet and light 4-page sections • Mis-feed & double sheet control with I.R. detection • Sheet jamming detection • PJ-77R Jogger receiving tray for collating only. Stitcher comprising: • IFU-200 Infeed unit • SPF-200A Stitcher folder with 2 stitching heads • FC-200A Foredge trimmer with single knife • LC-200 Long conveyor delivery. SPF-200A specification: Um8Lp23Mlp Sheet size, Max: 356 x 508 mm Min : 120 x 180 mm Sheet weight, standard: 64 – 157 gsm Coated: 85 – 157 gsm Production speed : up to 4,000 booklets per hour, A4 portrait. : up to 4,500 booklets per hour, A5 portrait.

Condition: good (used), Year of construction: 2005, operating hours: 60,000 h, Functionality: fully functional, workpiece weight (max.): 1,500 kg, travel distance X-axis: 500 mm, travel distance Y-axis: 350 mm, travel distance Z-axis: 300 mm, workpiece width (max.): 1,050 mm, No reserve price - guaranteed sale at the highest bid! Condition: Machine has been resealed at the basin Dqx87R TECHNICAL DETAILS Max. workpiece dimensions (W x D x H): 1,050 mm x 800 mm x 295 mm Max. workpiece weight: 1,500 kg Max. workpiece weight: 780 x 630 kg Table dimensions: 780 x 630 kg Axes movement range (X, Y, Z): 500 mm x 350 mm x 300 mm Axis speed (rapid traverse): 0.1 m/s Wire diameter: 0.1 - 0.3 mm Wire tension: 0.1 - 0.25 N Bevel cut unit axis travel range (U x V): ±21° x ±21° Detection method for each axis position (X, Y, U, V): Linear scale Dielectric liquid tank Working volume: 750 l Filter flow rate: 60 l/min Filtration accuracy: 3 μm Filter element: Paper filter x 2 Dielectric conductivity (range): 0.5 - 30 x 10^4 Ωcm External dimensions (W x D x H): 880 mm x 2,070 mm x 1,565 mm Weight (dry): 400 kg MACHINE DETAILS External dimensions (W x D x H): 2,210 mm x 2,873 mm x 2,150 mm Weight: 3,500 kg

Condition: good (used), X Axis-350 mm Y Axis-220 mm Z Axis-220 mm Max. workpiece length-850 mm Max. workpiece width-500 mm Max. workpiece height-200 mm Max. workpiece weight-500KG Weight-2200 kg Dqx3Pd

Condition: excellent (used), Year of construction: 2004, operating hours: 3,450 h, Functionality: fully functional, machine/vehicle number: 1551.0401, Muller Martini Presto, 2004-mod, 3.450 hours, 6 stations model 1551.0401 (3 double) Cover feeder, model 1528.0417 Bi29Oa9C9Dl Three-knife-trimmer Model 1522.0413,

Year of construction: 2016, Condition: ready for operation (used), General Data Measurements width 2600 mm Measurements depth 2600 mm Measurements height 2340 mm Machine weight 3300 kg Main Drive Number of axis 5 Movement X-Axis Movement 550 mm X-Axis Rapid Traverse 9.8 m/min Y-Axis Movement 350 mm Y-Axis Rapid Traverse 9.8 m/min Z-Axis Movement 400 mm V-Axis Movement ±45 mm V-Axis Rapid Traverse 9.8 m/min U-Axis Movement ±45 mm U-Axis Rapid Traverse 9.8 m/min Workpiece Workpiece weight 1500 kg Injection Unit Injection pressure 20 bar Media Dielektikum tank 1200 liters This 5-axis AgieCharmilles CUT 300MS was manufactured in 2016, featuring submerged wire-cutting technology. It supports a maximum workpiece size of 1200 × 700 × 400 mm and a weight up to 1500 kg. The machine offers rapid movement across X, Y, U, V axes at 9.8 m/min and includes integrated collision protection. If you are looking to get high-quality precision cutting capabilities, consider the AgieCharmilles CUT 300MS machine we have for sale. Contact us for more information. Dq08Td Application Types EDM

Year of construction: 1997, Condition: used, under power travels: X 350 mm, Y 250 mm, Z 220 mm table: 630x530 mm max. work piece 8Acdulriu weight 500 kg max. work piece size w x d x h: 800 x 575 x 215 mm tank capacity 400 l weight 2740 kg machine size 1390x1865x1800 mm water tank size 800x1360x1720 mm size of el. box 800x600x1880 mm

Condition: used, Steel ropes Wire ropes Sling ropes made of steel Length: 10 m Diameter: 25 mm Loops right/left Bwb320Jg00 Load capacity: 5 tons 8 pieces available 240125

Condition: used, Year of construction: 2022, table length 640 mm table width 540 mm 810 x 700 x 215 mm travel x / y / z 400 x 300 x 220 mm V-axis 120 mm U-axis 120 mm workpiece weight max. 500 kg Control M800 D-CUBES wire dia. 0,1 - 0,3 mm weight of the machine ca. ca. 3,1 t dimensions of the machine ca. 2,8 x 2,1 x 2,1 m Mechanical engineering concept: Hybrid design Machine included: - ODS - Optical Drive System - Tubular direct drives in XYUV axes - Linear scales in XYUV axes - Collision protection XYUVZ axes - Intelligent AT - Automatic wire threading for wire diameters 0.10 - 0.3 mm - Automatic fine hole search function - Easy 3D-Setup workpiece position detection - 5 controlled axes - prepared for additional axes - PFC - Precise Finish Circuit - H-FS - Finishing stage - LLS - Long Life System - 10 kg wire station - 4-sided framing table - hardened - Wire alignment block - Wire chopper - Compressor cooler Mitsubishi Electric M800 D-CUBES control system: - 19” full-touch monitor with gesture control - Hand pilot with configurable LCD display - Job planner incl. job interruption function - 3D CamMagic on board - Import of 3D Parasolid, 2D DXF / DWG - Graphic check: 3D, front and side view and top view - Operating and maintenance data output included - Interfaces: Ethernet TCP-IP, 2 x USB port - Corehole technology Incl. the following special options: - ERGO-Lux light Ergonomic workspace lighting with LED floodlight Two LED lights, 3 x 6 watts each IP67 version for use in the work area Anodized aluminium housing with reflector insert - Training course 5-day basic seminar at a Mitsubishi training center Mitsubishi training center for 1 person if attended within 12 months of commissioning. Travel and accommodation costs are at your expense - all dimensions, weight and performance data without obligation - Used machine without warranty Dq2Qk7 - interim sale reserved -

Condition: good (used), Year of construction: 2006, machine/vehicle number: 06F2S855, Measurements width: 2013 mm Measurements depth: 2632 mm Measurements height: 2100 mm Machine weight: 3500 kg X-AXIS Movement: 500 mm Ug7Eoibgaz Y-AXIS Movement: 350 mm Z-AXIS Movement: 300 mm Workpiece weight: 1500 kg Outer length: 780 mm Outer width: 630 mm

Condition: new, 5004K030, NF-K-4-30, EPA, 3 phase 4 wire line filter Model: 5004K030 Dqz799 Type: NF-K-4-30 Condition: New

Year of construction: 2007, Condition: ready for operation (used), General Data Measurements width 2300 mm Measurements depth 1940 mm 7Oqq0Xx3G Measurements height 2600 mm Machine weight 3460 kg Movement X-Axis Movement 500 mm Y-Axis Movement 350 mm Z-Axis Movement 426 mm V-Axis Movement ±70 mm U-Axis Movement ±70 mm Workpiece Workpiece weight 400/800 kg This AgieCharmilles Agiecut Classic V3 was manufactured in 2007. A wire EDM machine, it features dimensions of 1940 × 2300 × 2600 mm and a total weight of 3460 kg. It supports workpiece dimensions up to 1050 × 650 × 420 mm and a maximum weight of 800 kg. The machine offers a taper angle up to ±30° and a dielectric volume of 1000 liters. Contact us for more information about this machine. Application Types EDM

Condition: good (used), Renz ECL 360 wire closer The device is in perfect condition, ready for production. Renz ECL 360 wire closer: Electric crimping via foot pedal Binding up to 34 mm (340 sheets) in one cycle Efficiency approx. 400 cycles/h depending on the type and format of the material Foot cycle start allows you to set the material with both hands Dqv0Ar Screws with a diameter of 3/16” – 1 1/2” regardless of the pitch Quick settings of different spiral diameters in a few seconds Quiet operation. The device does not require the use of a compressor Weight 30 kg Power supply 230 V

Condition: ready for operation (used), Wire Electronic DSV 5431-25 / 380 - DSV 5431-25/380, serial number as per photo, used, normal signs of use, 100% functional, scope of delivery as per photos Dq093V

Condition: used, Year of construction: 2018, Wire erosion / EDM Travel distance X: 600 mm Travel distanceY :400 mm Travel distance z: 350 mm max. workpiece size X: 1030 mm max. workpiece size Y: 800 mm 7Jffgvkcw max. workpiece size Z: 350 mm max. workpiece weight: 1000 kg table size X: 950 mm table size Y: 630 mm with AWF ( Automatic Wire Feeding ) U / V axis: +/- 50 mm submerged cooling unit Taper angle +/- 30° at 50 mm height 16kg spools

Year of construction: 2013, Condition: ready for operation (used), This 5-axis AGIE CUT 300 wire EDM machine was manufactured in 2013. It features a maximum taper angle of 30/100° mm, can handle workpieces up to 1050 x 650 x 250 mm, and supports a maximum weight of 400 kg. If you are looking to get high-quality EDM capabilities, consider the AGIE CUT 300 machine we have for sale. Contact us for more information about this machine. Application Types 7Omzubn08 EDM

Condition: used, Year of construction: 2011, Wire erosion / EDM Travel distance X: 450 mm Travel distanceY :300 mm Travel distance z: 320 mm max. workpiece size X: 710 mm max. workpiece size Y: 560 mm Dq030R max. workpiece size Z: 300 mm max. workpiece weight: 800 kg table size X: 710 mm table size Y: 560 mm with AWF ( Automatic Wire Feeding ) U / V axis: +/- 100mm submerged cooling unit Wire diameter: 0.1 mm to 0.3 mm Maximum cutting angle: ±15° at 100 mm Tank capacity: 700 liters Control system: MGW-S6

Year of construction: 2013, Condition: ready for operation (used), Main Drive Number of axis 5 Additional Equipment Programmable Wire Tension: 0.3 to 3 daN / Automatic Threading and Rethreading for Wire: 0.30 to 0.20 mm Large Spools: Weight 25 kg (K250) NC Functions: File Management, AC CAM EASY, EDM-EXPERT, OPERATIONS ORGANIZER, Fast Measuring Cycles, 3D Graphic Simulation, Integrated Documentation, PART EXPRESS, Job List, SURFACE-EXPERT, POWER-EXPERT, PROFIL-EXPERT 7Onxnxali Options: TAPER-EXPERT, e-Connect, e-Supervision, e-Control / Extended Taper Cutting: From 30° to 45° / Used Wire Processing: Wire Chopper Rotating Axes: Index or Servo-Control / Automatic Part Leveling: 3D SET UP / Optical Measuring System: OMS / 3D Probing: Renishaw Probe This 5-axis AGIE CUT 400 Sp wire EDM machine was manufactured in 2013. It features a high-speed CC generator, automatic threading, and rethreading for wires from 0.30 to 0.20 mm. The machine includes a PC-based control system with a touchscreen and offers advanced NC functions like 3D graphic simulation and integrated documentation. If you are looking to get high-quality EDM capabilities, consider the AGIE CUT 400 Sp machine we have for sale. Contact us for more information. Application Types EDM

Year of construction: 2005, Condition: ready for operation (used), Control Unit Model Makino Mgw-r Main Drive Number of axis 4 Movement X-Axis Movement 450 mm Y-Axis Movement 300 mm 0Yjarw2Oi Z-Axis Movement 320 mm U/V Movement ± 101 mm Workpiece Workpiece X 500 mm Workpiece Y 300 mm Workpiece Z 730 mm Workpiece weight 800 kg Additional Equipment Accessories: Portable handwheel This 4-axis Makino EU43 wire EDM machine was manufactured in 2005. It features a robust control unit, the Makino Mgw-r, and can handle workpieces up to 800 kg, with maximum dimensions of 730 x 500 x 300 mm. Ideal for precision machining, it includes a portable handwheel for ease of use. If you are looking to get high-quality EDM capabilities, consider the Makino EU43 machine we have for sale. Contact us for more information. Application Types EDM

Year of construction: 2014, operating hours: 3,288 h, Condition: ready for operation (used), General Data Measurements width 2760mm Measurements depth 2025mm Measurements height 2015mm Machine weight 2700 kg Main Drive Number of axis 5 Movement X-Axis Movement 400 mm Y-Axis Movement 300 mm Z-Axis Movement 220 mm V-Axis Movement 120 mm U-Axis Movement 120 mm Workpiece Workpiece weight 500 kg Dqwifv Table Outer length 540mm Outer width 640mm This 5-axis Mitsubishi MV1200S erosion machine was manufactured in 2014. It features a robust design with dimensions of 2025 mm x 2760 mm x 2015 mm and a weight of 2700 kg. Capable of handling workpieces up to 500 kg and 215 mm in diameter, it offers a comprehensive movement range with X-axis 400 mm, Y-axis 300 mm, Z-axis 220 mm, U-axis 120 mm, and V-axis 120 mm. With only 3288 machining hours, the Mitsubishi MV1200S machine we have for sale is in very good condition. Contact us for further details regarding this erosion machine. Application Types EDM