Used Chocolate Coating Machine for sale (65,331)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. Bledpfx Aewzl Hxjgked ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time Bjdpfx Aswfgbrjgkold ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Year of construction: 2025, condition: new, DOLFIN-kbn2 series parts washing machines are used for the purpose of washing the parts, which are also larger in size and heavy, requiring rinsing, passivation or another process, particularly after washing. While it is desired to have no oil and other contaminants on the surface before assembly or packaging at the businesses and factories manufacturing parts in masses, it may also be necessary to remove the washing chemical used in the 1st stage from the surface of the part according to the utilization areas of the part. For this requirement, rinsing or a similar implementation in 2nd step is compulsory. Our KBN 2 series parts washing devices are special devices that contain more than one tank and/or bath. While the parts that are placed in the device are rotated on their own axis by means of the washing basket, pressurized detergent hot water is sprayed. With the pressure, temperature and chemical effect, all oil and contamination on the part is cleaned. After the washing process and following the direction of the washing chemical to its own tank, the rinsing operation starts in the 2nd tank. If desired, the 3rd tank can be added and another function is added after rinsing. Since Dolfin Parts washing machines operate as closed loop, new water and new detergent are not used every time. While washing is performed for several times with the same tank, all the dirt remains in the washing cell. With this feature, it protects both nature and employees. Due to its high efficiency and performance, saves energy, water and labor. The device automatically completes the loop in accordance with the values of the washing parameters that have been entered from the control panel before operation. All processes are carried out with specially prepared programs along with PLC. Bledpov S Dihjfx Agkjd In order to load, particularly the heavy items into the washing basket or to remove them from the basket, the washing basket can be taken on a carrier trolley, in other words, from the device when required. It can be transferred to any point of the workshop with this trolley. We produce for you with 40+ years of experience! We export to more than 30+ countries with quality and trust.

Year of construction: 2025, condition: new, DOLFİN- VDL series Drum (Spiral) parts washing machines are used particularly for the purpose of cleaning small parts that are manufactured in large quantities and in bulk. Bjdpfsv S Dk Ssx Agkjld The materials that are poured from the inlet part of the spiral drum in the device are directed towards the outlet part of the drum with the spirals inside the drum. While the drum moves in its own axis according to the set rotation speed, it subjects its parts to, respectively, washing (degreasing), rinsing, passivation and drying processes (varies per the model). Since these processes are sequential and continuous, all processes are completed quickly and effectively within a single device. Full penetration is ensured by pressurized spraying and dipping effects in each section. It is a very functional model of us that is used particularly for washing the bolts, nuts, washers, or such small parts, fittings, nipples, couplers and fittings that are processed in CNC and automated machines in high quantities. Regardless of the metal type of the parts to be washed, they are fully compatible with steel, brass, aluminum copper or stainless steel materials. Since Dolfin Parts washing machines operate as closed loop, new water and new detergent are not used every time. While washing is performed for several times with the same tank, all the dirt remains in the washing cell. With this feature, it protects both nature and employees. Due to its high efficiency and performance, saves energy, water and labor. The device operates continuously in accordance with the values of the washing parameters that have been entered from the control panel before operation. Parts that come out of production in bulk can be loaded into our device in 3 different manners. 1. With Vibrating Loading Chamber, 2.With Lift Conveyor, 3. By coupling to our Customer's existing system, Do not hesitate to contact for more information. We produce for you with 40+ years of experience! We export to more than 30+ countries with quality and trust.

Condition: new, Year of construction: 2025, operating hours: 24 h, functionality: fully functional, DOLFİN-PYM2 series parts washing machines are industrial purposed parts cleaning devices that are used before and after revision, particularly in repair and maintenance services. While the parts that are placed in the device are rotated on their own axis by means of the washing basket, pressurized detergent hot water is sprayed. With the pressure, temperature and chemical effect, all oil and contamination on the part is cleaned. Since Dolfin Parts washing machines operate as closed loop, new water and new detergent are not used every time. While washing is performed for several times with the same tank, all the dirt remains in the washing cell. With this feature, it protects both nature and employees. Due to its high efficiency and performance, saves energy, water and labour. Blsdpfx Aov Sa I Togkod It works automatically in accordance with the temperature and time values that are set during operation. In order to load, particularly the heavy items into the washing basket or to remove them from the basket, the washing basket can be taken on a carrier trolley, in other words, from the device when required. It can be transferred to any point of the workshop with this trolley.

Condition: used, Year of construction: 2015, XYZ 2-OP Vertical Machining Centre ProtoTRAK TMX Control (2015) Year of Manufacture: 2015 Spindle Speeds to 6,000rpm Spindle Taper BT30 Table Size 457 x 381mm Table Travels 355 x 305 x 455mm (XYZ) 6 Station ATC Rapid Traveres 15m/min Bjdpfxeya H Nke Agksld Footprint 760 x 1,220 x 2500mm Weight 1100kgs 415V Electrics Air Require for ATC For sale with *Jet Machinery Ltd* Jet Machinery Stock No: #79155 Machine Serial Number: SOP02060 Cost: £17,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: ready for operation (used), Year of construction: 2012, XYZ SLX555 x 3m ProtoTRAK Control Gap Bed Centre Lathe ProtoTRAK SLX Control (2012) Max. Distance Between Centres 3000mm Max. Swing over Bed 560mm Max. Swing over Gap 935mm Max. Swing over Cross slides 350mm Max. Cross slide Travel 290mm Spindle Nose D1-11 Spindle Bore 104mm Spindle Speeds 30 – 1800rpm Spindle Motor 15Hp Quick Change Tool Post Tailstock MT7 Tailstock Dia’ 75mm Tailstock Travel 160m Manufactured | 2012 Dimensions: L x D x H 5220 x 2150 x 1950 mm Weight 7400 kg Supplied with: 3 Jaw Chuck Machine Handbooks TRAKing®. Constant Surface Speed. Rapid Traverse with Joy Stick. QCTP & Holders 2 x Fixed Steadys 15” Interlocking Guards Auto Lubrication. Coolant. Worklight We can offer delivery & installation, operator training and warranties. *For sale with Jet Machinery Ltd* Jet Machinery Stock No: #79024 Machine Serial Number: SLM00035 Blsdoyaywhepfx Agkjd £47,500.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: new, functionality: fully functional, Year of construction: 2025, machine/vehicle number: 27042010, TICAB (Trade Industrial Company AB) — a leading manufacturer of road maintenance equipment in Europe — offers you a cost-effective solution for efficient local repair of asphalt concrete surfaces. A portable asphalt recycling plant / recycler RA-800 from TICAB with its own engine and hydraulic drive produces 800 kg of high-quality asphalt mixture for every 20-30 minutes from asphalt scrap, milling, bitumen, crushed stone, sand. It also allows you to warm up the material and work with it within the area of laying or replacing asphalt. Equipment is ideal for emergency road repairs. Technical Specifications: ● Diesel engine with electric starter (10hp). ● Recycler productivity - 1800 - 2500 kg/hour. ● Drum capacity 800 kg (0,6 m3). ● Product heating temperature - 120 – 160 °C. ● Product heating time up to 15-20m (160°C). Bedpjvrw Anjfx Agkold ● Fuel tank for 100 l (equipped with a fuel level indicator). ● Power of burner 100-130 KW. ● Burner diesel powered by a generator with a voltage stabilization system. ● The recycler drum is equipped with a heating distribution system (on the whole surface). ● Side flaps construction provides light access to servicing drum rollers. ● Control panel with indicators and at least one 220V power outlet on this panel (can be used for charging tools or lighting). ● Control panel, power block equipped with locks protection

Condition: like new (used), RR120 is a high-volume system for printing, coating, inspecting, and drying rolls. Its modular design offers flexibility for specific applications and needs Reel to Reel Handling System 7 Dispensing Channels (Tandem Pumps Bio-Jet, Front Line and Air Jet Dispensing Technologies Print up to 7 Lines Simultaneously Automated Dispense Tracking for Precision Line Placement Perform Multiple Applications on One System Adjustable Tension for Handling Backed/Unbacked Membranes Easy to Set up, Operate and Maintain Data Storage to Support Multiple Applications Many System Options Can be Upgraded after Purchase Bodpfxjya Hvqe Agkeld

Condition: ready for operation (used), Year of construction: 2007, XYZ SMX SLV 3 Axis Turret Milling Machine ProtoTRAK | SMX Control (2007) 3 Axis CNC Capacity (X Axis, Y Axis & Quill) Spindle Taper ISO 40 Spindle speeds to 70 - 3600 RPM Table Size 1473 x 305mm Table Travel: X - 1000mm Y - 410mm Knee Travel: Z - 413mm Quill Travel Z - 127mm Air Power Draw Bar Supplied with a range of spindle tooling Coolant Year of Manufacture: 2007 Weight: 1850 Kgs Power Requirements: 18A Bedpfx Agsx Tiq Sokold *For sale with Jet Machinery Ltd* Jet Machinery Stock No: #79109 Machine Serial Number: 12308 Cost: £14,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: excellent (used), Year of construction: 2020, Machines for the production of medical masks type llr , ffp2. Price per piece. Bsdpfx Agjr Iydyeksld

Condition: like new (used), Thom Type SI Spout Inser­ter Machi­nes for inser­ting the spouts into pre­fa­bri­ca­ted pou­ches. Model - Thom SI‐900 Bjdpox Utd Eofx Agkold Semi­au­to­ma­tic machi­ne Ide­al for sam­ple pro­duc­tion and small series pro­duc­tion Capa­ci­ty: Up to 10 pou­ches / min. Thom fil­ling and packa­ging machi­nes are in demand ever­y­whe­re whe­re fle­xi­ble packa­ges need to be fil­led (pou­ches / refills): in the food indus­try, the cos­me­tics and deter­gents indus­try or in the beverage fil­ling.

Condition: new, Year of construction: 2025, Roll forming metal siding “double façade panel” machine SPM-2 Roll forming metal siding “double façade panel” machine SPM-2 is new design product of our company for façade and wall metal panels forming with the necessary configuration. These double façade panels are very popular in construction business of cladding residential buildings and industrial structures, for the construction of fences of various configurations, gazebos, roofing elements, etc. The SPM-2 metal siding production line is fully automatic and consists of a rolling part of the machine, an automation system and guillotine cutting shears at the machine exit. The line can have as additional parts a manual or automatic uncoiler for metal rolls, depending on the customer's needs. As standard version, this metal siding double façade panels roll forming machine SPM-2 makes a flat panel profile, but with the additional equipment, it is possible to roll panels with a microwave or rib shape profile. To start rolling, it is necessary to install a roll of metal to the decoiler and to put the end of the strip to the first rolling rollers of the equipment and feed it into them. After step by step, to put the metal to the next rollers, adjusting it if necessary. When metal comes to the cutting device of machine you need to feed metal into cutting knives and to make “zero” cut. After such step, equipment can move to automatic operation mode. The control panel of machine has the ability to set the number of tasks and the length of products, single tasks or to work in multitasking mode. After setting up necessary parameters the machine will automatically roll the metal cladding wall panels and cut them into necessary sizes. Thus, the customer will receive final product as quickly as possible and with the highest possible result. The roll forming speed is adjustable and can be up to 10-15 meters per minute. The SPM-2 metal wall cladding panels production line has special tools for punching out fastening holes on the side of the panel. It makes possible for the customer to get more interesting solution options and to offer a wider range of products to the end user. The rolling part of the machine has 18 pairs of forming steps, ensuring high quality of final product. You can get machine with protective cover or without it as per your request preferences. Specifications Blodpfx Agjxghngekod Material width (mm) 416 The material thickness (mm) 0,4-0,5 Engine power (kW) 3 + 1,1 Rolling speed (m/min) 10-15

Condition: new, Year of construction: 2017, functionality: fully functional, operating hours: 25 h, input voltage: 380 V, type of input current: three-phase, total height: 1,500 mm, total length: 5,200 mm, total width: 2,350 mm, overall weight: 2,500 kg, saw band length: 520 mm, saw band width: 580 mm, New machine. Blsdpfx Agjunia Hskod

Condition: new, Year of construction: 2024, functionality: fully functional, ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Excellent Support! ✈️ Price includes shipping within Germany – No additional transport costs! ✈️ Fast delivery: Only 6 weeks after receipt of payment! PROFESSIONAL POWDER COATING HAS NEVER BEEN THIS EASY! Looking to expand your business and enter the world of professional powder coating? The PEF2.5+ is the perfect solution for beginners! This high-performance system allows efficient, cost-effective, and high-quality coating of car rims and smaller workpieces – with minimal effort! ✨UNBEATABLE PROMOTION – ONLY UNTIL THE END OF MAY!✨ Take advantage of this limited-time offer before it's too late! PONY Luxury Coating – QUALITY THAT CONVINCES! ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✅ 100% European manufacturing – No China products, only top quality built to European standards! ✅ Modular & expandable – Additional options for greater performance and flexibility! ✅ All spare parts included – Long-term use with no hidden extra costs! ✳️Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today. ✳️ ✨✨Buy directly from the manufacturer and secure price and quality advantages!✨✨ ☘️Environmentally friendly☘️⚡️Green Energy⚡️☘️ Bodpewfhu Hefx Agkold Powder oven + powder booth + powder gun Complete Starter Package PEF2.5+ ⭐ Powder oven with electric heating ✔️ INTERNAL WIDTH: 1,505mm ✔️ HEIGHT: 1,800mm (from air duct) ✔️ INTERNAL LENGTH: 2,500mm ✔️ Thermoblock unit dimensions: 785x1800x2210mm; heating capacity is 30 kW/h; recirculation fan is 1.5kW/h – 1 pc.; exhaust fan is 0.54kW/h. ✔️ Double-wing door with thermal insulation and silicone seal. ✔️ Guide rails for rack trolleys are manufactured according to the dimensions specified on the base plates. ✔️ Specially designed air duct for homogeneous air distribution inside the curing oven. ✔️ Electrical panel materials by Siemens and Schneider. This curing oven does not include a PLC system. PLC is available as an option. ✔️ Curing temperature, curing time, and heater unit function are adjustable. At the end of the program, an alarm and light signal from the buzzer will indicate completion. ✔️ Additionally, a product transport trolley with cast wheels is located inside the oven. ⭐ Powder coating booth ✔️ Dimensions: 800x1930x2200mm (including fan) ✔️ Teflon filters: 4 pcs. ➢ Filter suction fan: 4kW x 1 pc. (6,000m3/h – 200mmSS) ✔️ 36W LED lighting x 1 pc. ✔️ Bottom drawer x 1 pc. ✔️ Control panel for air intake and powder spray regulation ✔️ DELTA frequency converter ✔️ Heavy-duty rollers under the coating booth ✔️ Additional filter at the fan outlet ⭐ Powder coating gun E-Coat+3 Master with Multicolor (vibration table) Enquire now – Get your business ready for the future! ☀️ 2-YEAR WARRANTY ☀️ ☀️All our machines are CE-certified and necessary machines have ATEX certificates.☀️

Condition: new, Year of construction: 2024, functionality: fully functional, This powerful machine to meet the requirements of larger woodworking companies, ensuring exceptional sharpening results. Equipped with an electronic tooth counter and an autonomous cooling system. The ZM150 offers precise sharpening while maintainingoptimal operating conditions. With two electric motors, including a 150mm CBNdisk for sharpening and a motor reduction group for precise blade movement,this sharpener delivers outstanding performance. Power supply voltage - 380-400V Frequency - 50Hz Power - 0.20kVa Capacity - 65 teeth per min Blade width - 20 to 100 mm Tooth pitch - 6 -25mm Sharpening disc - Profiled 150mm CBN disc Bljdpjxiv Ugefx Agkjd Weight - 115kg

Condition: new, Year of construction: 2025, The ZM101 is a pioneering product in our lineup, designed to sharpen sawblades with widths of up to 100 mm at a remarkable rate of 65 teeth per minute. This efficiency enables it to simultaneously service 3-4 bandsaw/sawmill machines. Equipped with an abrasive ceramic disk, the ZM101 can expertly sharpen all teeth with profiles. Its robust construction allows it to perform reliably under the most demanding conditions, making it a favorite among our customers. Additionally, its straightforward design ensures ease of use and low maintenance costs, further enhancing its appeal. Technical characteristics: Maximum length of the blade: 6000 (8000) mm Minimum width of the blade: 20 mm Maximum width of the blade: 100 mm Maximum height of the tooth: 12 mm Front angle of the tooth: 0÷25° Tooth pitch: Profile N: 10, 12.5, 15, 20, 25 mm Profile WM: 22, 25 mm Working capacity: 65 teeth/min Size of the abrasive disc: Blsdpfx Aexlfwpjgked Cut-in sharpening, profile N: ø200 x 10 x ø32, ø200 x 13 x ø32 mm Profile sharpening, profile WM: ø200 x 8 x ø32, ø200 x 10 x ø32 mm Voltage: 380 V Power of the electric motors: 0.09 and 0.37 kW Size: Without band saw holder (L x W x H): 750 x 550 x 1100 mm With band saw holder (L x W x H): 2000 (3000) x 1000 x 1100 mm

Condition: new, Year of construction: 2025, The ZM101 is a pioneering product in our lineup, designed to sharpen sawblades with widths of up to 100 mm at a remarkable rate of 65 teeth per minute. This efficiency enables it to simultaneously service 3-4 bandsaw/sawmill machines. Equipped with an abrasive ceramic disk, the ZM101 can expertly sharpen all teeth with profiles. Its robust construction allows it to perform reliably under the most demanding conditions, making it a favorite among our customers. Additionally, its straightforward design ensures ease of use and low maintenance costs, further enhancing its appeal. Technical characteristics: Maximum length of the blade: 6000 (8000) mm Minimum width of the blade: 20 mm Maximum width of the blade: 100 mm Maximum height of the tooth: 12 mm Front angle of the tooth: 0÷25° Bjdpfjxliguex Agkeld Tooth pitch: Profile N: 10, 12.5, 15, 20, 25 mm Profile WM: 22, 25 mm Working capacity: 65 teeth/min Size of the abrasive disc: Cut-in sharpening, profile N: ø200 x 10 x ø32, ø200 x 13 x ø32 mm Profile sharpening, profile WM: ø200 x 8 x ø32, ø200 x 10 x ø32 mm Voltage: 380 V Power of the electric motors: 0.09 and 0.37 kW Size: Without band saw holder (L x W x H): 750 x 550 x 1100 mm With band saw holder (L x W x H): 2000 (3000) x 1000 x 1100 mm

Condition: excellent (used), Chocolate tanks chocolate kettle 200l chocolate kettle, stainless bowl and agitator, digital temp control, side bottom discharge, 3Ph Bsdpfx Agouqcncekeld

Condition: excellent (used), With acid-resistant section, with high pressure nozzles, equipped with a conveyor Bedpet Ity Djfx Agksld Overall Size: 9,5 x 1,15 x 1,9 m Opening size: 530 x 250 mm Chemical tank (heated): 0,5m³ Rinse tank (heated): 0,3 m³ Drying fans: 12db Voltage: 380 V

Condition: used, BROACHING MACHINE Bledpfxot Hr Dfs Agked

Condition: refurbished (used), ROLLFORMING MACHINE Bedpefgl Aqsfx Agkjld PRODUCING SQUARE PROFILES WITH 5 TONES OF TOOLS MADE IN ITALY

Condition: good (used), Year of construction: 2018, Table 1473 x 305mm, Traverses XYZ: 1000 x 410mm x 400mm (knee), quill travel 127mm, Spindle Taper ISO40, Bsdpfxoxftqde Agkeld Power Drawbar, Spindle Motor 5HP, Spindle Speeds 70 - 3600rpm, Prototrak SMX CNC Control,

Condition: good (used), functionality: fully functional, For sale: older freezing unit for cleaning rubber parts, older make. The machine is operational. - Drum volume: 150 l - Working range: from -40°C to -130°C Bledpex A Sz Ajfx Agksd - Dimensions (incl. shaking/separation table) (W x L x H): 2.2 m x 4.3 m x 2.4 m

Condition: new, functionality: fully functional, color: other, Year of construction: 2025, Vertical Shaft Impact Crushers (VSI) stand out among rock crushing machines due to their high crushing efficiency and excellent particle shape production. Developed by CONSTMACH, these sand-making machines are used in the tertiary crushing stage to give cubic form to materials obtained from secondary crushers and to produce a high proportion of fine material. The system offers superior performance in processing all types of minerals and ores, as well as hard rocks such as basalt and granite. High-quality sand is produced from materials with a maximum feed size of 45 mm. Vertical shaft impact crushers allow you to easily obtain the desired product size for different material types thanks to their variable speed rotor system. It offers production capacity flexibility with a high reduction ratio, large feed hopper, and four different crushing chambers. In addition, high-chromium wheel shoes, anvils, and heavy-duty bearings ensure long life and low maintenance costs. The independent lubrication system and optional anvil replacement mechanism maximize uptime. Vertical Shaft Impact Crusher Technical Specifications Model: VSI-700-CR Maximum Feed Size: 35 mm Weight: 6,500 kg Motor Power: 110 kW Rotor Diameter: Ø700 mm Rotor Speed: 60–70 m/s Production Capacity: 60–100 t/h Model: VSI-800-CR Maximum Feed Size: 40 mm Weight: 12,000 kg Bodsxqf Uropfx Agkold Motor Power: 2 x 160 kW Rotor Diameter: Ø800 mm Rotor Speed: 45–60 m/s Production Capacity: 150–200 t/h Model: VSI-900-CR Maximum Feed Size: 45 mm Weight: 14,500 kg Motor Power: 2 x 185 kW Rotor Diameter: Ø900 mm Rotor Speed: 50–60 m/s Production Capacity: 200–250 t/h Model: VSI-1000-OR Maximum Feed Size: 90 mm Weight: 15,000 kg Motor Power: 2 x 200 kW Rotor Diameter: Ø975 mm Rotor Speed: 50–60 m/s Production Capacity: 250–300 t/h Why Choose CONSTMACH Vertical Shaft Impact Crushers? CONSTMACH is a globally preferred brand in the production of stone crushing machines and sand making machines with its engineering quality. Our vertical shaft impact crushers offer high performance, low operating costs, and long-lasting use. Our models, which can be customized to the production needs of each facility, provide the advantages of easy maintenance and high efficiency. CONSTMACH is always the right choice for businesses seeking quality, reliability, and sustainable production. What Do We Do at Constmach? Constmach is a leading machine manufacturer serving the construction and mining industries with a wide range of products. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.