Used Cnc Double Column for sale (23,312)

Condition: used, Machine not operational - control system not functioning Hfjdpfsdzqptox Aftel Available at a special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Factory No. 300487, Year of Manufacture 2006 Pressing force: 500 tons Distance between columns (front and rear): 2520 mm Table area: 2500 x 2500 mm Ram area: 2500 x 2500 mm Ram stroke: 600 mm Maximum installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable forward speed: 100-800 mm/s Pressure build-up to 5000 kN: approx. 0.7 sec. Return stroke speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking in the top dead center position - Adjacent control cabinet (200 x 50 cm) - Electrical control system SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7") - 2-hand control panel located beside the machine - Floor-level installation - Table top 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication system - Operating manual with circuit diagrams Space requirement (L x W x H): 372 x 260 x 460 cm Space requirement for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: used, Year of construction: 1984, pressure 500 t Hodpfx Afst Hwpyjtofl passage width 750 mm stroke 120 mm total power requirement 57 kW weight of the machine ca. 16 t dimensions of the machine ca. m

Condition: used, Year of construction: 1985, Technical details: pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm Hfedpfou Nfh Dsx Aftsl ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm This press is currently for sale without controls. Optional on customer request completion possible. i.D. *

Condition: used, Technical details: pressure: 80 t distance between columns: 880 mm dayligth: 200 mm Table dimensions: 880x300 mm height over floor: 1000 mm distance between columns: 800 mm total power requirement: ca. 12 kW machine weight ab.: 2855 kg space requirements of the machine approx.: T:1,4xB:1,65xH:1,9 m Embossing - Hot Embossing application area: - for example: for foils, plastics, paper, hardboard materials etc. - stamp plate size: 600x310mm equipment: - counter - hydr. tank Accessories: - Mounting plate (600x300x90mm) not heatable. Hedpfxou Icwto Aftefl Sale as is. *

Condition: new, CNC double-head mitre saw equipped with Ø 600 mm saw blades, designed for precise and automated cutting of profiles. The machine features a robust electro-welded steel base and consists of one fixed cutting unit and one mobile cutting unit with electronic positioning along the X-axis. Both cutting heads are equipped with controlled rotary axes (RF and RM), allowing automatic positioning of the cutting units at angles ranging from 45° inward to 20° outward. The saw blades are operated by hydro-pneumatic cylinders, with adjustable feed speed and rapid return. Hfjdpeztb Hpofx Aftsl Main features: CNC double-head mitre saw Ø 600 mm saw blades One fixed and one mobile cutting unit Electronic positioning of the mobile unit – X-axis Controlled rotation of both cutting heads – RF and RM axes Cutting angle range: 45° inward to 20° outward Hydro-pneumatic blade feed Adjustable blade feed speed Rapid blade return Horizontal clamping system with double cylinders Vertical profile clamping system Pneumatically operated safety guards for the cutting areas 15” touch-screen monitor Windows 10 platform Programming and management of cutting operations via touch-screen interface Provision for an industrial label printer for workpiece identification and association with the corresponding production order The machine is designed to provide precision, productivity and ease of operation, and can be easily integrated into the production process.

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 700 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :600 mm Hfodpfx Asfxyh Reftjl Ram plate:700 x 600 mm table height over floor:850 mm Table size:700 x 600 mm speed of forward flow:10 mm/sec Pressing speed:10 mm/sec :10 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,2 t dimensions:950 x 2440 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück heating plates :550 x 500 mm :6800 ? :2400 ? :1200 ? :1200 ?

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 550 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :550 mm Ram plate:700 x 600 mm table height over floor:900 mm Table size:700 x 600 mm speed of forward flow:50 mm/sec Pressing speed:10 mm/sec :50 mm/sec Oil cooling (electric):1,5 kW (max) Hfodpfx Afofxygpstsl Oil Tank Capacity:300 l weight of the machine ca.:4,3 t dimensions:1150 x 2600 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück Heating panels (L x B) with 2 measuring sensors diagonally:550 x 500 mm Siemens Control System:S7 1200 Monitor:12 Zoll :2400 ? :1200 ? :1200 ?

Condition: used, Year of construction: 1990, Technical details: Pressure: 63 t distance between columns: 200 mm stroke: 150 mm dayligth: 430 mm no. of strokes: 400 Hub/min T-slots H 12 650: 18 mm hole in table: 420x160 b x l mm ram surface area: 650 x 450 mm control: Wanske Tronicpress CNC passage of columns: 550x540 mm tank: 200 l stroke of ram - fixed: 100 mm ram diameter: 40 mm table height over floor: 1000 mm table: 600x450 mm table height over floor with metal base stand: 880 mm total power requirement: 30 kW weight of the machine ca.: 3,9 t Hydraulic automatic punching press for precision work (high-speed press) - for punching, drawing, pressing, minting, bending, riveting, straightening, assembling - with hydraulic gripper feed type HS 150 and 7-roller straightener (moving) - Normal strips of approx. 0.4mm - 2.5mm thickness x approx. 160mm width, as well as narrow strips up to approx. 4mm can be processed. Feed length can be adjusted as required via the control unit. - with ram round column guide - with automatic central lubrication - High-speed: up to 400 strokes min-1 - motorized adjustable fixed stop (bottom can be adjusted by hand/motorized) - Operating modes such as continuous stroke and/or single stroke Equipment: - 1x hydraulic unit - 2x control cabinets Hedpfju Icxqex Aftsfl *

Condition: excellent (used), Year of construction: 2001, x-travel 2200 mm y-travel 3200 mm z-travel 1250 mm Control FIDIA C20 c-axis +/- 200 ° milling-head swivable +/- +90 ° milling-head swivable +/- -100 ° feeds X-axis 50 m/min feeds Y-axis 50 m/min feeds Z-axis 50 m/min tool taper HSK A63 tool change unit 16 Pos. spindle turning speed range 18000 U/min distance between columns 4060 mm dist. milling spindle - table surface 1796 mm connected load 238 kVA weight of the machine ca. 45 t dimensions of the machine ca. 9 x 7 x 5 m This JOBS LinX6 is in very good condition and can be viewed under power by arrangement with the seller. Description: Jobs LinX6 Type: 5-axis milling machine with movable gantry and fixed table Control: FIDIA C20 Year of manufacture: 2001 Travel X: 2200 mm Y travel: 3200 mm Z travel: 1250 mm A-axis travel: +90° / -100° C-axis travel: +200° / -200° Max. feed rate in X/Y/Z: 50 m/min Table clamping surface: 4000 x 2500 mm Clearance between columns: 4060 mm Clearance height between table and portal: 1807 mm Clearance height between table and spindle nose: 1796 mm Milling head: T2K D.01.06 Tool holder: HSK A63 Tool changer: 16-fold Spindle power: S1 from 6800 rpm 40KW Spindle speed: 250 - 18000 rpm Total connected load: 238 kVA Special equipment: - Siemens linear motors in all axes - JIMS / preparation for semi-automatic motor spindle change - Replacement spindle as spare part - External coolant supply / 1000L tank - Minimum quantity coolant dosing Hodpoxa Hl Rofx Aftefl - Scraper conveyor - Renishaw TS27 tool measuring system - Ethernet connection - Manual control module Other: Complete documentation available Machine weight: approx. 45 tonnes Space requirements: 8.7 m (width) x 6.7 m (depth) x 5.1 m (height)

Condition: used, Year of construction: 2002, machine/vehicle number: 10857, Pressure total: 315 ton Stroke: 1100 mm Daylight: 2200 mm Table surface area : 2500 x 1000 mm Slide area: 2500 x 1000 mm Die weight at the ram max.: 6000 kg Approach speed: 600 mm / sec Working speed: 32 - 230 mm / sec Return speed: 600 mm / sec Required power: 158 kW Weight of machine approx.: 44 ton Height over floor approx.: 6175 mm Automation Hfedpfxovmfzbs Aftjl

Condition: used, pressure 200 t throat - mm stroke 250 mm Table dimensions 2420 x 840 mm ram surface 1850 x 650 mm dayligth 500 mm ram adjustment 110 mm distance between columns 1900 mm table height 170 mm no. of strokes 25 - 45 Hub/min total power requirement 22 kW dimensions of the machine ca. 2550 x 2370 x 3820 mm Hjdpjgk Rfzofx Aftofl weight 30 t - pneumatic clutch - press safety valve, Herion - cam switch, Balluff - chain break monitoring - hydr. overload, Hydac - motor. alide adjustment with digital display - separate control cabinet with safety control ABB - separate two-hand control panel with foot switch - slidable side protective doors - front protection by light barriers vertical + horizontal The machine shown and described above is safe for hand inlays. The machine is also in anorther variant or also can be used as an automatic feeder. Equipment possible according to customer agreement.

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm rapid traverse 22 mm/s Hsdevprv Repfx Aftjfl stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company.

Condition: used, Year of construction: 1973, pressure 1000 t distance between columns 4150 mm stroke 1200 mm distance table/blankh.,max. stroke up,adjustm. up 2100 mm table surface area 4000 x 2200 mm die-cushion pressure inside the table 360 t stroke of drawing cushion in table 300 mm Hedpfx Asynmm Ssftsfl die-cushion pressure in pusher 100 t stroke of drawing cushion in pusher 150 mm ram surface 4000 x 2200 mm column travel -side 1300 mm die-cushion inside the table hydraulic, controlled die-cushion in pusher hydraulic, controlled Cut Shock absorption hydraulic Control Siemens S7 height over floor 7,7 m total power requirement 300 kW weight of the machine ca. 280 t dimensions of the machine ca. 5,75 x 4,3 x 9,55 m Year of construction 1973 Modernization 2005 with oil-hydraulic drive, hydraulically controlled drawing cushion in the table and Ram, hydraulic cutting impact damping stored dismantled - short video available from the seller before dismantling

Condition: used, Year of construction: 1973, pressure 1000 t distance between columns 4150 mm stroke 1200 mm distance table/blankh.,max. stroke up,adjustm. up 2100 mm table surface area 4000 x 2200 mm die-cushion pressure inside the table 360 t Hjdpfxoyn R D Uj Aftsfl stroke of drawing cushion in table 300 mm die-cushion pressure in pusher 100 t stroke of drawing cushion in pusher 150 mm ram surface 4000 x 2200 mm column travel -side 1300 mm die-cushion inside the table hydraulic, controlled die-cushion in pusher hydraulic, controlled Cut Shock absorption hydraulic weight of the machine ca. 280 t The machine was overtaken 1999.

Condition: used, Year of construction: 1973, pressure 1000 t distance between columns 4150 mm stroke 1200 mm distance table/blankh.,max. stroke up,adjustm. up 2100 mm table surface area 4000 x 2200 mm die-cushion pressure inside the table 360 t Hfodpfx Asyn R Eloftol stroke of drawing cushion in table 300 mm die-cushion pressure in pusher 100 t stroke of drawing cushion in pusher 150 mm ram surface 4000 x 2200 mm column travel -side 1300 mm die-cushion inside the table hydraulic, controlled die-cushion in pusher hydraulic, controlled Cut Shock absorption hydraulic weight of the machine ca. 280 t The machine was overtaken 1999.

Condition: used, Year of construction: 2005, Pressure 800 t distance between columns 2560 mm stroke 1050 mm Distance table/ram, stroke up 1870 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 395 mm Die cushion area in table 2300 x 1300 mm Ram surface 2500 x 1730 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 150 mm Side window 1000 mm Oil volume 4300 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m Height above floor 7,0 m year of manufacture 1974 overhaul 2005: formerly type BZE 800, converted to ZE 800 by manufacturer with new ram and new cylinder mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel stored in dismantled condition - Video at seller’s site before dismantling available Hsdpfxozrpt Io Aftofl

Condition: new, Year of construction: 2026, functionality: fully functional, pressing force: 250 t, table width: 1,000 mm, table length: 1,200 mm, die cushion stroke: 200 mm, The machine still needs to be built. Requirements can be considered where possible. Ejector in ram – approx. 10 t. Table draw cushion approx. 800 x 850 mm. Weight approx. 18 t. Stroke approx. 600 mm. Hfodpfx Aevga H Eoftjl

Condition: used, Year of construction: 2006, machine/vehicle number: 18282, Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Hjdpfx Afsuqd S Aetofl Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l

Condition: used, Year of construction: 1996, machine/vehicle number: 14.194, Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Hodpfxeu Saaao Aftefl Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.

Year of construction: 1992, condition: ready for operation (used), Turrets: 2, tool stations: 12, tool holder: VDI 40, max. turning diameter: 320mm, max. swing diameter: 390mm, spindle bore: 61mm, speed: 5000rpm, spindle power: 15kW, travel X/Z: 230mm/430mm, machine dimensions X/Y/Z: 3900mm/2000mm/2900mm, weight: approx. 8600kg. Including robot. Documentation available. On-site inspection is possible. Hedpfx Afoyhgpaetsfl

Condition: excellent (used), Year of construction: 1993, functionality: fully functional, Manufacturer: GIGANT Model: G2-1200/2 Year: 1993 Condition: Used Stock number: 0375 Hfodpfxsx R U Ids Aftsl Pressing force: 1200 t Number of pressing points: 2 Die table size: 3,700 x 2,700 mm Ram size: 3,700 x 2,700 mm Ram stroke: 1,000 mm Max. vertical clearance: 1,590 mm Die opening at BDC: 610 mm Lower blankholder stroke: 400 mm Movable bolster: Present at the front

Condition: used, Year of construction: 2010, pressure 600 t distance between columns 3640 mm stroke fix 350 mm no. of strokes 11 - 44 /min dayligth (stroke and adjustment up) 1550 mm column travel -side 2200 mm table surface area 3600 x 2500 mm ram surface 3600 x 2500 mm ram adjustment 400 mm band width 2000 mm material thickness 0,6 - 2,5 mm material cross-cut 1600 x 2,5 mm² coil weight 35,0 t Number of Straightening rolls 13 0 straightening roll diameter 50 mm Blanking Line (press, coil line, blank stacking system) yom 1993 - 2010: new control Siemens S 7 - press Schuler type EBS 4-600 with infinitely variable drive, fly-wheel brake, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, ram interlocking moving tables (2x) without rails for the moving tables Hjdpjzrppcefx Aftefl - decoiler make Schleicher, type HE - 355 - 2100, yom 1994 with auxiliary drive, snubber roll - coil lifting device - extractor device make Schleicher - shear - straightening machine make Schnutz, type RME 18/50/13-2000 TZ, yom 1994 with infinitely variable drive, 30 intermediate rolls, 117 supporting rolls - coil loop bridge - roll feed make Schleicher, type WV-SYS-A 160-2000, yom 1994 - blank stacker NSM-Magnettechnik stored in dismantled condition - Video before dismantling available

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload Hfedpfx Afjgpxc Sjtel - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet

Condition: used, Year of construction: 1984, pressure 10 t distance between columns 500 mm Hsdst Hwwdopfx Aftsfl stroke 200 mm total power requirement 10 kW weight of the machine ca. 4.500 kg dimensions of the machine ca. m

Condition: used, pressure 200 t distance between columns 1600 mm max. ram stroke 600 mm dayligth 900 mm table width 1600 mm table depth 1300 mm Hedpog S R Twofx Aftjfl table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 rapid traverse 400 mm/s return speed 325 mm/s pressing speed 42 mm/s bei 40% mm/sec pressing speed 20 mm/s bei 100% mm/sec die-cushion pressure 800 kN die cushion stroke 150 mm speed of die cushion auf 68/ ab 225 mm/s