Used Cnc Machining Center for sale (68,661)

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Only 110 operating hours! Equipment and technical data: Travel ranges: - X = 1800 mm - Y = 900 mm - Z = 80 mm Lhodpfow Nadysx Adwjb Made from 18 mm Koskisen panels Milling bed made of 19 mm MDF as sacrificial plate with guide rails and T-slot nuts for clamping. Chassis with reinforcements, filled with polymer concrete, designed for transport by pallet truck or forklift. Mechanical set consisting of profile rails including linear guides and ball screws (2010 and 1605) for all axes. Shaft couplings and high-performance grease for lubricating the carriages; also includes energy chains with connection sets. Control set comprised of a Triple Beast controller for controlling 3 axes, with Ethernet interface. Leadshine drive for the fourth motor. Four stepper motors, 5.0A, 3Nm each with motor cables, as well as a 48V 6.7A switching power supply, LED board for breakout board, ribbon cable and proximity sensors; small parts such as wire leads, ferrules, control cables, heat shrink tubing, and cable lugs. Fully pre-installed in an aluminum enclosure including electrical kit and emergency stop. - 21.5 inch built-in monitor, including mini PC with Windows 7, Rhino 5.0 CAD software, Estlcam G-code generator, Beamicon2 control software, as well as mouse and keyboard, all pre-installed in an ergonomic console. Tool length sensor for determining tool length and adjusting the active reference point. Special equipment: - High-frequency spindle with 2.2 kW, including clamping nut, frequency inverter, line filter, brake resistor, and collet set. - PC with 8 GB RAM and AMD processor - Rhino 5.0 CAD software for creating both simple 2D data and 3D solids Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Equipment and Technical Data: - For classic nesting processing with wear plate - Machine frame of welded construction with ground and hardened prism guides for the gantry, unit head, and consoles - Gantry-type traveling column - Helical rack and pinion drive in X and Y axes, ball screw in Z axis for precise positioning - Working dimensions: - Max. support area on nesting table: X = 3100 mm, Y = 1560 mm - Max. traverse paths: X = 4695 mm, Y = 2100 mm, Z = 293 mm - Max. clearance height over DYNESTIC table: Z = 100 mm from table top (without wear plate) - Maximum programmable speed Vector speed: 128 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min - DYNESTIC table: - Fixed, continuous processing table with grid layout - Continuous grooves in X and Y directions - Groove spacing: 50 mm - Includes 25 meters of sealing cord for clamping the wear plate - Vacuum fields: Single-circuit vacuum system - Drilling unit 7877: - 19 spindles - Drive power: 1.7 kW - 13 vertical spindles: - Individually selectable - Arranged in U-shape - 5+4 in X direction, 4 in Y direction - 32 mm spacing - Max. drill diameter: 35 mm - Total drill length: 70 mm from screw-on end (depending on panel thickness) - Spindle stroke: 70 mm - Rotational direction: alternating clockwise/counterclockwise - Speed (max): 1000 - 4400 rpm, infinitely variable - Tool holder: M10 thread, 11 mm fit - Without tool, without holder - 6 horizontal spindles: - 2 double drill spindles in X direction - 1 double drill spindle in Y direction - Tool holder: M10 thread, 11 mm fit - Max. total drill length: 63 mm from screw-on end - Without tool, without holder - Milling unit 7842: - Power: 12.0 kW (S6) - Max. speed = 1000 - 24,000 rpm, infinitely variable - Max. power at 12,000 to 24,000 rpm - Air-cooled - With HSK-F 63 tool holder - With right-hand threaded nut (for right-hand rotating tools) - With collet chuck for HSK shank - Ceramic ball bearings (hybrid bearings) - Tool weight max. 6 kg (incl. holder) - Tools: milling and grinding tools max. Ø 160 mm - Safety enclosure according to CE standard - Side and rear safety fence - Vacuum pump: 500 m³/h, dry-running - Personnel safety ensured by light barriers in the front machine area - Hand-held control device for remote operation of the machine with the following functions: - Start/stop of the processing program - Control of processing cycle speed Lsdpfx Adewka Upjwohb - Reset button - Manual feed/rapid traverse for all axes - EMERGENCY STOP - CAMPUS V7 CAD/CAM software 1x machine license consisting of: - CAMPUS NC-HOPS: - Graphic variant system with WOP and CAD/CAM features for creating part variants using macro technology - CAMPUS MT-Manager - CAMPUS Workcenter - CAMPUS DXF interface - Automatic central lubrication - Automatic lubrication at defined intervals - Additional sealing against dust via pressurization in each guide carriage

Condition: used, Year of construction: 2017, operating hours: 4,898 h, travel distance X-axis: 1,600 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 800 mm, CNC machining center, used Manufacturer: AWEA Model: BM-1600 Year of manufacture: 2017 Control system: Heidenhain iTNC 530 HSCI Operating hours Spindle hours: 4,898 h Total power-on hours: 18,739 h Working area: X-axis: 1,600 mm Y-axis: 800 mm Z-axis: 800 mm Spindle: Speed: 10,000 rpm Power: 22/35 kW Taper: BT 50 Table: 1,700 x 800 mm Max. load: 2,000 kg Equipment: - 40-position tool changer - Through-spindle coolant 20 bar - Electronic handwheel - Left-side chip conveyor - Direct linear measurement Lhsdjx I S E Iepfx Adwsb The machine was used in-house for manufacturing products by an automation technology company. A significant amount of aluminum processing was done on this machine.

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Condition: Well-maintained (ready for demonstration at customer site) Equipment and technical specifications: Console machine Working size X: 3,200 mm Working size Y: 1,470 mm Max. travel height Z: 325 mm Milling unit 7939, 6 kW (S6) Including laser pointer Including traveling disc tool changer 7996 with 18 positions Including stationary tool changer on the right side Including 7893 magazine for manual tool change position 8 consoles including 12 vacuum suction cups for 4-field machining 4 pneumatically raisable and lowerable loading aids Including hand control unit Including 3-field safety tread mats Including saw unit for sawing/grooving in X Including C axis 7997 Horizontal drilling units: 6 Vertical drilling units: 16 Double drilling spindle in X Heat exchanger for control cabinet cooling CAMPUS software for CNC machining centers Vacuum pump 100 m³/h Weight: approx. 4,450 kg Lhsdpjxymfksfx Adwsb The tools shown in the tool changer are not included in the scope of delivery! Availability: by arrangement Location: Rhineland-Palatinate

Condition: used, Year of construction: 2024, New demonstration machine!! List price: €52,742 (net). Forescolour, consisting of milling table (X-axis), gantry (Y-axis), Z-axis unit in compact board and base frame with adjustable machine feet. Milling bed with 19mm MDF sacrificial board. Table openings pre-configured longitudinally and transversely. Mechanical set consisting of profile rails including profile rail carriages, ball screw and precision racks. All elements assembled, pre-lubricated, including test run, ready to use immediately. Control set consisting of control cables, energy chains, planetary gears, stepper motors, high-performance drivers, power supply, and toroidal transformer, fully pre-mounted in the control cabinet, including sensors for each axis. Switching relays for automatic operation of the existing extraction system. Brush seals for dust protection, as well as CE-compliant safety devices provided by a moving extraction device and a laser scanner mounted on one side for working area monitoring, with a 275° and 5.5m field range (machine positioned in a corner of the room). Handheld control unit with all necessary machine operation functions, including emergency stop button and dead man's switch. Tool length sensor to determine tool length and active zero point offset. High-frequency spindle with 2.2 kW, including collet nut, frequency converter, line filter, braking resistor, and collet set. Monitor as a built-in monitor, including mini PC with Windows 10, pre-installed with Beamicon2 control software, as well as mouse and keyboard, integrated in an ergonomic desk. CAD license Rhino 7.0 and CAM license Estlcam V11, as well as all necessary documentation, will be sent by email prior to delivery. Vacuum table: Milling bed designed as a vacuum table, consisting of four adjustable segments. Cross table made of PE with a top plate of ... vacuum pump from Becker company with a capacity of 100 m³/hour, oil-lubricated. For connecting the vacuum pump, a 16 Ampere, 400 V AC plug is required. The customer must supply HDF 3mm double-sided raw board (2500x1300mm) as sacrificial plate for the entire vacuum table (recommended use: processing coated wood-based materials). Tool set in systainer: Tool set in systainer consisting of: - 1 pc. 1.5mm left (HF152LIVHM) - 1 pc. 3.175mm 30° (HF30GVHM) - 1 pc. 6mm 90° (HF90GVHM) - 5 pcs. 4mm Z2 (HF41REVHM) - 1 pc. 5mm Z2 (HF52REVHM) - 1 pc. 5mm Z3 (HF53SRECAR) - 2 pcs. 5mm Z2 (HF52REDIA) - 1 pc. 5mm Z2 (HF52UPDOWN) - 1 pc. 4mm Z3 (HF43REVHM) - 1 pc. 6mm Z1 (HF61REVHM) - 1 pc. 8mm Z2 (HF82LAVHM) - 1 pc. 10mm Z2 (HF10SVHM) - 1 pc. 12mm Z2 (HF12SVHM) Maintenance package in systainer: grease gun 150 ml, one cartridge of high-performance grease 400 g, spray can of silicone spray grease 500 ml, one grease fitting with hose section and 30mm face milling cutter with indexable inserts. Pneumatic unit: consisting of four cylinders, throttling check valve, push-in fittings, angle push-in fittings, silencer connectors, filter regulator, push-in manifold, PE hose, and brackets, for use in a pre-configured table opening (for end-face machining). If pneumatics are required for both table openings, the position must be calculated twice (NOTE: Compressor to be provided by customer.) Technical data: Travel (X / Y) 2500 x 1300 mm, Z = 200 mm Dimensions (L / W) 1980 mm, 3800 x 2300 mm, H = 1900 mm Footprint: approx. 20 m² (smallest installation size) Weight: 1500 kg Lhodpfxew Tfy Uj Adwob Rated voltage: 400 V Repeat accuracy: +/- 0.1 mm Connection values: 4.3 kW HF spindle

Year of construction: 2022, condition: new, Offer on demand Machine is immediately available Lhodpfx Aeiw Dgisdwob

Condition: like new (used), Year of construction: 2019, operating hours: 900 h, functionality: fully functional, travel distance X-axis: 3,600 mm, travel distance Y-axis: 1,500 mm, Next to new nesting CNC machining center Lhsdpfexz Rfqox Adwsb 4-axis nesting CNC machining center. Purchased new in 10/2019. Has been used for less than 900 hours. The business for which the machine was acquired ceased due to the Corona pandemic, and usage has therefore been very minimal. The machine has been connected to an AL-KO extraction system, which is also for sale in a separate listing. Table size 3600x1500 mm. The machine can be used as a nesting table machine or, by removing the panel, vacuum pods can be used to raise the workpiece for machining. The machine is in full working order in all respects and is an excellent alternative to a new machine. Automatic 10-position tool changer, 2 x Busch rotary vane vacuum pumps (250 m³/h each). The work area can be divided into two separate zones. Drilling unit for vertical and horizontal drilling. Slot saw. Automatic tool height measurement (enables processing the same job with several tools without noticeable height differences). Supplied with bSolid software in Finnish. Suitable saw aggregate and planer aggregate also available for sale. The machining unit features collision sensors, so safety fencing is not required. The buyer is responsible for all costs related to relocation, including the preparation and transport of the machine (these services can be arranged, for example, through the machine's importer).

Condition: good (used), Year of construction: 2011, Ref. -No.: 10565 Manufacturer: TOYODA Type: FH 630 SX Year of construction: 2011 Type of control: CNC Control: Fanuc 31i - A Storage location: Halberstadt Country of origin: Japan Serial no.: NS3XXXX X-Travel: 1000 mm Y-Travel: 800 mm Z-Travel: 850 mm B-Axis: 360 ° Distance Spindle /Table: 200 - 1050 mm Max. Workpiece Weight: 800 kg Max. Tool Weight: 27 kg Max. Tool Length: 545 mm Max. Tool Diameter: Ø120 mm Max. Size Of Workpiece Lxwxh: Ø 1000 x 1000 mm Tool Taper: BT - 50 Tool Piece Magazine With: 60 Pcs./pcs. Spindle Speed: 6000 RPM Rapid Travel X/Y/Z: 60 mm / min Tool to tool: 2,4 sec Lhodpjxvw I Ijfx Adwob Machine length: 7000 mm Machine width: 3500 mm Weight Of The Machine Ca.: 20,1 t Pallet height: 1200 mm Positioning (X, Y and Z axes):: + - 0,003 mm Repeatability (X, Y and Z axes):: + - 0,0015 mm Payload pallet: 800 kg Axial: 14700 N Further information: - Cutting feed (same for X-, Y- and Z-axis): 0.001 - 30m/min - Distance between spindle center and upper edge of the area: 100mm - 900mm - Table size range: 630 mm - Positioning of the lower table: 1 ° - Positioning of the rotary table: 0.001 ° - Tools used: SK 50 - Operating oil: 53l - Slide lubricating oil / spindle head lubrication: 3.0 l - Coolant for spindle & ball screw head: 37l Machine can be inspected under power by arrangement.

Condition: good (used), Year of construction: 2008, Ref. -No.: 10564 Manufacturer: TOYODA Type: FH 630 SX Year of construction: 2008 Type of control: CNC Control: Fanuc 31i - A Storage location: Halberstadt Country of origin: Japan Serial no.: NS2XXX X-Travel: 1000 mm Y-Travel: 800 mm Z-Travel: 850 mm B-Axis: 360 ° Max. Workpiece Weight: 800 kg Max. Tool Weight: 27 kg Max. Tool Length: 545 mm Lhodoxvw Izspfx Adweb Max. Tool Diameter: Ø 120 mm Max. Size Of Workpiece Lxwxh: Ø 1000 x 1000 mm Tool Taper: BT - 50 Tool Piece Magazine With: 60 Pcs./pcs. Spindle Speed: 6000 RPM Machine length: 7000 mm Machine width: 3500 mm Weight Of The Machine Ca.: 20,1 t Further information: - Equipped with IKZ and chip conveyor - NC rotary table 360,000 * 0.001° Machine can be inspected under power by arrangement.

Year of construction: 2025, condition: new, XX100292 New CNC Machining centre with 4 controlled axes FOM INDUSTRIE FMC 470 Machine in stock and ready for shipping Standard configuration: - Liquid-cooled electrospindle 7 kW, 20,000 rpm (HSK-F63) - 9 location tool magazine on head (HSK-F63) - No. 2 pairs of pneumatic vices with positioning through the travelling column - No. 2 pairs of low profile jaws for clamping wide profiles - Left pneumatic reference stop - Minimum quantity lubrication (MQL) with pure oil - Central automatic greasing system and device for manual greasing - Chip and waste collection tank in base - Perimeter guard system with automatically opening, front retractable doors - X FLOW (automatic orientation of lubricant nozzles) - Control: POWER-D - Movable control console - 24” display - FST CAM 4 program Optional equipment installed on the machine: - PR202941 Fixed tool magazine for 8 positions in the center on the machine base - PR202962 Device for checking the integrity and measuring tool length - ZR204058 Pendulum mode with multiple workpieces (2 work areas, 4 workpieces) and processing of non-standard lengths with X-PAL: Lhedpfxjiv Imns Adwjb • Two pairs of additional vices with independent positioning • Transformation of std vices into vices with independent positioning • LED bar • Profile positioning software • Software for viewing the progress of the processing cycle • Device for measuring profile length • Second X-FLOW • Right pneumatic reference stop • Pendulum control software • Safety devices for pendulum processing • Tunnel for oversized profile machining • Software to manage oversized machining operations • ''Clock'' time calculation module program - PR202971 Data import software in accordance to FOM protocol and wireless optical bar code and QR code reader - ZP715010 Module for rigid tapping and chase tapping - PR202957 Hinged belt conveyor with ramp - PR203389 Rear chip collection tank - PR202975 Tool set A3/HSK F63 - PR202967 Angle head with vertical disc Ø 230 mm - PR202968 Cone with horizontal disc Ø 250 mm - PR204497 Holder HSKF63 with cutter Ø 200 x 6 mm - PR203072 Software adjustment of the vice pressure 3,5 - 7 bar - ZP714611 License for the office version of FST CAM 4

Condition: used, CNC 5-Axis HMC – Horizontal Machining Center, Milling Center, Manufacturing Center Manufacturer: LICON Model: Liflex 1266 PC B1 Year of construction: 2016, Commissioned: 2017 Equipped with SIEMENS 840D SL (Solution Line) CNC path control, with 5 simultaneously controlled axes Travel paths X: 1200 mm, Y: 660 mm, Z: 650 mm A-axis as swivel bridge +/– 135° (270°) B-axis 360° continuous Axis acceleration X + Y-axis 6 m/s² Axis acceleration Z-axis 9 m/s² Feed force X + Y-axis 7500 N Lhjdpfx Ast Ac Efsdweb Feed force Z-axis 10000 N Positioning tolerance (X/Y/Z) 0.008 mm A-axis swivel speed 180° rotation in 4 sec. Interference diameter on the swivel bridge max. 1400 mm Transport load on the swivel bridge max. 700 kg Tool holder HSK 63 Spindle speed max. 12,000 rpm, stepless Spindle power 37kW at 40% duty cycle Spindle torque at 40% duty cycle 85 Nm Maximum spindle torque 100 Nm Tool change time (chip-to-chip) approx. 3.7 sec. Tool diameter with adjacent slots occupied Ø 140 mm Tool diameter with adjacent slots free Ø 250 mm Maximum tool length 400 mm Maximum tool weight 20 kg Power supply 400 Volt, 50 Hz Connected load 80 kVA Compressed air connection 5-8 bar - LIFLEX MSP 80/63/85/12,000 motor spindle (output 37kW/40% duty cycle) with liquid cooling and recooling unit - 2-axis rotary tilting table LICON as B- and C-axis, with hydraulic axis clamping - Zero-point clamping system on the swivel axis turntable - Dual pallet changer, without pallets (these need to be newly sourced) - Media transfer of 5 single-action pressure lines for oil or air, for workpiece clamping on the pallets Hydraulic functions from 30-150 bar, with pressure monitoring (controllable via M-functions) - Tool changer with 30 tool positions, disc turret type - Machine designed for dry machining with minimal quantity lubrication (MQL) system - MQL-TSC, internal MQL lubrication supply through the spindle - Scraper belt chip conveyor, discharge height 1150 mm - Licon ECO-Mode (energy-efficient aggregate operation) - Direct linear measurement system on all axes - Operating hours (control voltage on) ≈ 7,500 h Space required for operation L x W x H 9,000 x 5,000 x 3,800 mm Space required for transport L x W x H 6,100 x 4,400 x 3,600 mm Base machine weight approx. 21 tons Total weight: approx. 24 tons Very good condition

Condition: new, Year of construction: 2026, Gannomat ProTec - CNC through-feed machine for drilling, grooving and routing Short introduction: • Small footprint requirement, less than 3,3 m2 • Large (1000 x 5600 x 60 mm) and small (60 x 250 x 6 mm) workpiece dimensions • Gentle workpiece handling by air jets • Precision through double laser measurement and workpiece straightening • Fast processing through 21/23 drilling spindles • 21/23 drilling spindles for zero setting times • Stable grooving unit till 8,3 mm saw blade width • Strong routing unit 5,5 kW (S1), option • Automatic tool changer for routing unit, option CNC controlled DRILLING, GROOVING, ROUTING below 3,3m2 with high processing precision and zero setup time, this stands for the GANNOMAT ProTec. TECHNOLOGY: Lhjdjbiplropfx Adwsb The massive processing unit is equipped with 13 vertical drilling spindles, 8 double-horizontal drilling spindles (6Y & 2X), 1 grooving saw in the Y-axis with 1 routing unit. This unit placement allows that all conventional drill / tools are in one seting and only need to be called up. This CNC-controlled machining center operates from the bottom and can work in the through-feed and back-feed mode to the operator. Steel working tables with air jets are the reference for horizontal drilling and in the combination of the massive workpiece clamping system and additional 4th axis at the drilling head, precision drilling is possible. A non-contact laser sensor is used for recognition of the actual workpiece edges (Top and bottom edge), this allows a automatic correction / adjustment of the drilling program. USERS: ProTec offers Hightech in technology and application and was developed as a entry-CNC-level-machine for small and medium companies on the one hand and on the other hand as a second machine to a

Year of construction: 2024, condition: new, XX100329 CNC Machining Centre with 3 axes and worktable with pneumatic positioning at 0°/90°/180° FOM INDUSTRIE FMC 120 Machine in stock and ready for shipping Standard configuration: - Servo-ventilated three-phase spindle motor 3 kW, regulation of spindle rpm by numerical control - inverter (1000/17000 rpm) - 6 position tool-holder for manual change with pneumatic locking (ISO 30) Ledjhlkqpepfx Adwjhb - Pneumatic rotation of the work table 0° to 90° to 180° - Mobile control console with PC, 24'' - No.4 pneumatic vices with manual positioning and double pressure with safety valves - Manuallly adjustable profile reference stops on right and left of work table - Minimum quantity lubrication (MQL) with pure oil - Perimeter safety casing on 3 sides and retractable front door - FST CAM 4 program Optional equipment installed on the machine: - PR204851 5-position automatic tool magazine (ISO 30) - PR207680 4-vice Easy-to-Set configuration: • Transformation of standard vices into vices with automatic movement and pneumatic locking • 2 retractable pneumatic side stops • SW for vice positioning - PR-28965 Beam rotation stop for intermediate angles with manual adjustment - PR204833 External stop with tunnel - PR202971 Data import software for data in accordance to FOM protocol with wireless bar-code reader - PR-27602 Tool set for aluminium - QN-28849 ISO 30 cone with milling cutter Ø 75 mm thickness 6 mm for end milling

Condition: good (used), Year of construction: 2018, Internal item no.: 25043 5-Axis CNC Machining Center POSmill H 500 U Year: 2018 Just approx. 1,000 spindle hours since spindle replacement Machine total approx. 20,500 hours Spindle replaced in 2024 (18,000 rpm) Geometry realigned in 2024. Travel axes: X 650 / Y 850 / Z 500 mm Rotary table: 360° infinite Control: Heidenhain iTNC 530 Spindle: 18,000 rpm Spindle interface: HSK-A63 The machine is equipped as follows: Ledpfjwz I Acex Adwjhb 60-position tool changer Through-spindle coolant (20 bar) with belt filter system Compressed air through the spindle Kessler rotary table, diameter 500 mm Infrared 3D part measurement probe Tool measurement via BLUM laser Rotating inspection window POS DCM collision module Mobile electronic handwheel Oil mist extraction system Heidenhain linear measurement system X, Y, Z Purge air for all linear measurement systems Active control cabinet air-to-air cooler Active cooling for 4th + 5th axis, controlled Network connection + USB port Controlled spindle cooler Heidenhain rotary measuring system Contour protection POSkontur External hinge belt chip conveyor Coolant pump at the head, operated via M-functions Pump for chip flushing device Chip flushing device Machine status indicator light Spindle air purge Electromechanical oil/coolant separator Automatic coolant level monitoring 3-fold media interface in the center of the table Hydraulic unit incl. control via M-function Connected load: 60 kVA Installation dimensions: W 4800 / D 4600 / H 3000 mm + Through-spindle coolant unit (LxWxH): 2200 x 1300 x 1400 mm Weight: approx. 13,000 kg The machine is in very well-maintained condition and comes from a small, family-run business. In 2024, the spindle was replaced and the geometry was set (guides repaired and adjusted). Since then, the machine has seen only minimal use.

Condition: good (used), Year of construction: 2009, Internal Article No.: 25040 CNC Machining Center Müga A7040 Year: 2009 Control: Mitsubishi + 4th axis + ICS (internal coolant supply) / filtration system / extraction system + NC clamp Röhm RKE-125L + SK40 tool holders Spindle: SK40 Spindle speed: 12,000 rpm 24-position tool changer Travel paths: X 700 / Y 400 / Z 550mm Lhodpfjwy U Ebox Adwob Dimensions (approx.): LxWxH 270 x 210 x 270cm Weight: approx. 4t

Condition: used, Year of construction: 2009, Offered here is a used machining center from the manufacturer Deckel Maho DMG. The machine is powered up and can be inspected at our facility. Free loaded on truck Manufacturer: DMG Deckel Maho Model: DMC 125 H duoBlock Year of manufacture: 2009 Control: Siemens 840 D Solutionline (PCU 50) Technical data: Travel distances X-, Y-, Z-axis: 1250 x 1000 x 1000 mm Feed rate X-, Y-, Z-axis: 20 - 60,000 mm/min Rapid traverse X-, Y-, Z-axis: 60 m/min B-axis travel: 360 x 0.001° B-axis feed rate: 10,800 °/min Max. rotation of table plate: 30 rpm Spindle speed: 20 - 8,000 rpm Gear stages: 2 Max. workpiece diameter: 1250 mm Max. workpiece height: 1580 mm Clamping surface: 800 x 800 mm Max. workpiece weight: 1,500 kg Weight of pallet: 570 kg Max. permissible weight difference for pallet loading: 1,000 kg Tool holder: SK 50 according to DIN 69871 Max. tool length: 650 mm Tool magazine: 120 positions Transport dimensions: 6,500 x 3,000 x 3,200 mm Transport weight of machine (without magazine or other accessories): approx. 20,000 kg Space requirement: approx. 7,000 x 6,000 mm Total machine weight: 24,000 kg Accessories: Lhodpsw Ew T Sjfx Adwsb Chip conveyor with coolant tank Coolant system 4x machine pallets Tool magazine Oil mist extraction Various new spare parts: 1x Length measuring system Y-axis (new) 1x Lubrication unit 230V 0.12 30 bar (new) 1x ZAHNRADP-AGG*MKF1-KW2-20036 (new) 1x Cyclo gearbox *F1C-A25 (new) 1x Conversion kit power module (new) 1x Lifting devices for the machine

Condition: used, Year of construction: 2001, Used machine Year of manufacture: 2001 Condition: Function tested Equipment and technical data: Milling unit: 4.4 kW Tool holder: HSK 63 F Speed: 1,000 - 18,000 rpm Water-cooled Tool changer: 4-position, lateral Drilling head: 9 vertical drilling spindles on a 32 mm pitch Horizontal drilling spindle: 1+1 Vertical drilling spindle: 1+1 Grooving saw in X-direction Control: Twin CAM 32 Vacuum pump: 40 cbm/h Including vacuum suction cups Travel paths: X-axis: 2,685 mm Lhedpjw I Ug Hofx Adwjb Y-axis: 1,095 mm Z-axis: 140 mm Weight: approx. 3,500 kg The machine is completely checked for all mechanical, electrical, and electronic components and overhauled where necessary. All guides checked; console guides replaced New PC control system for the TWIN CAM control All axis modules checked and serviced Location: Flörsheim Availability: by arrangement

Condition: ready for operation (used), A machining center with 10-station tool changer is offered. Table clamping surface X/Y: 600mm/300mm, travel X/Y/Z: approx. 420mm/300mm/250mm, spindle speed: 6000rpm. Tool holder: BT30. Control: Brother CNC-400, machine weight: approx. 2000kg, including manual. Inspection possible by appointment. Lhedpfx Ajx Ecu Esdwob

Condition: used, Year of construction: 2007, Used machine Year of manufacture: 2007 Equipment and technical data: Nesting system with grid table Processing dimensions: - X: 5000 mm - Y: 1240 mm - Z: 135 mm Traverse paths: - X: 5665 mm - Y: 1650 mm - Z: 325 mm with milling unit 7933: - Motor 11 kW (S6) - HSK 63 - water-cooled with C-axis with 18-position disc tool changer Lhedjwka Ipspfx Adwjb with vacuum pump 250 m³ with handheld control device with central lubrication with minimum quantity lubrication system Availability: short-term Location: Röllbach

Condition: good (used), Stock number: 3057 Manufacturer: Deckel MAHO Year of manufacture: 1999 Model: DMU 60 E Lhedsx Dtqbepfx Adwob Machine number: 11080000273 Control: Heidenhain TNC 624 M Operating hours: 34,055 h Spindle hours: 8,787 h Table: 1,000 x 540 mm Table load capacity: 350 kg Travel distances (X/Y/Z): 600 – 525 – 500 mm Spindle taper: SK 40 Tool changer: none Speed range: 20 to 12,000 rpm Spindle power: 10 / 15 kW Feed rate: 0 to 10 m/min Rapid traverse: 15 m/min Accessories: coolant system; 3D probe Condition: good Connected load: 26 kW Machine dimensions: 3,000 x 2,100 x 2,300 mm Weight: approx. 4.5 t

Condition: good (used), functionality: fully functional, travel distance X-axis: 2,400 mm, travel distance Y-axis: 3,600 mm, travel distance Z-axis: 420 mm, nominal power (apparent): 50 kVA, total height: 2,900 mm, total length: 12,480 mm, total width: 5,290 mm, table width: 2,200 mm, table length: 3,500 mm, spindle speed (max.): 8,000 rpm, spindle motor power: 10,000 W, Hello, we are selling a Breton CNC machine with 2 tables and automatic tool changer. The machine is still in operation and can be tested. We will dismantle the machine in January 2026. Lodpfxjx Af I Ne Adwjhb

Condition: excellent (used), Year of construction: 2017, CNC-controlled precision machining center Gannomat Type Protec 571 CNC Lhedpfx Adewvk Aueweb • For drilling, grooving, and milling Machining unit with PowerBlock featuring 21 spindles and 1 grooving saw: • Vertical drilling spindles: 13 • Horizontal drilling spindles in Y: 6 • Horizontal drilling spindles in X: 2 • Grooving unit in Y: 1 • Milling unit Profit: 4.5 kW, 3000 - 18,000 rpm with frequency converter • Workpiece width (X): min. 85 mm / max. 1000 mm • Workpiece thickness (Z): min. 6 mm / max. 60 mm • Workpiece length (Y): min. 285 mm in throughfeed mode / max. 5600 mm programmable workpiece length in software • Workpiece weight: max. 70 kg Processing speeds per axis: • On X-axis: max. 90 m/min • On Y-axis: max. 30 m/min • On Z-axis: max. 15 m/min

Year of construction: 2013, condition: excellent (used), Technical design: Console table 3050 x 1200 mm with manually movable 6 consoles , Lhodpfokqyizjx Adweb each console 2vacuum suction cups and a pneumatic lifting rail point laser set-up aid, vacuum pump CNC control XILOG Plus main spindle 8,5 kW (12 HP) HSK 63F with C-axis , 1500 - 24.000 rpm tool changer plate 12-fold 1 adapter unit swiveling saw drilling head with: 12 vertical spindles, 4+2 horizontal spindles, grooving saw bumper safety system The shown tools, HSK- tool holders, drills etc. are not included in delivery!

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, workpiece length (max.): 6,175 mm, workpiece width (max.): 1,550 mm, workpiece height (max.): 300 mm, spindle motor power: 18,500 W, Homag CNC Machining Center BAZ 211/60/K Venture 21 XXL with 6 m working length, PowerEdge edge banding unit, renewed vacuum pumps, Windows 10, and WoodWOP 8.1, in very good condition: – Workpiece length 6000 – 6175 mm Lhsdpfxjx Dzbzj Adwjb – Pendulum processing 2375 – 2550 mm – Workpiece width 1400 – 1550 mm – Maximum workpiece thickness 300 mm – Working height 950 mm (underside of workpiece) – Modernization I 2023: – 2 new rotary vane oil-lubricated vacuum pumps – Capacity 2 x 63 m³/h = 126 m³/h – Retrofit kit for separate cooling unit for main spindle – Modernization II 2024: – New machine PC with Windows 10 operating system – Upgrade to WoodWOP 8.1 – 4-axis CNC machining center – K console table – 10 consoles incl. front stops – 6 rear stops – 6 lift rails – 2 side stops each left/right/mirrored – 2 pneumatic connections per machining position – 2 vacuum connections for templates – C-axis with aggregate and electronic interface – Safety device with anti-slip mats – Main spindle 18.5 kW vector controlled – Liquid cooling for main spindle – 10+18-position disc tool changer: – 10-position disc changer moving with main spindle – 18-position disc changer moving with X-support – MPU drilling head 30 spindles V20 / H10 / S360° – MultiProcessingUnit with C-axis +/- 185° – 20 vertical high-speed spindles – 10 horizontal spindles – Grooving and separating saw 200 mm – PowerEdge 360° edge banding unit – Pickup station moving with X-support – Edge thickness 0.4-3 mm – Max. edge height 65 mm – 360° edge banding with butt joint – Pre-trimming station and single roller for PowerEdge – Hot air nozzle for edge banding unit – Combined flush trimming and finishing unit WD 60 mm – Flush trimming of edge overhangs – Finishing pre-milled edges – For use in main spindle – Probing for compensation of workpiece tolerance – 2 WPL radius cutter heads – 2 profile cutters for finishing unit – C-axis extension for Flex-5 unit – 10 LED position display systems for consoles – Optical LED display system – For positioning clamps and consoles – 4-fold configuration with 2 x 2 clamping positions – Separate vacuum systems – Detachable console for adjustable side stop – 2 additional side and longitudinal locating pins – 2 additional clamping consoles 1300 mm – 2 additional side and longitudinal locating pins – 2 additional lift rails for console table – 12 vacuum clamps 160x115x100 mm – 10 vacuum clamps 125x75x100 mm – Saw/drill unit with 2 spindles for tool changer – Saw blade diameter up to 240 mm – Side wall safety fence (left) – Rear safety fence – Side wall safety fence (left) – Year of manufacture 2008, single owner, very well maintained – Machine serviced regularly – No maintenance or repair backlog, no major defects – For sale ex location Karlsruhe / Southern Germany – Machine is still connected and fully operational – Inspection and trial run possible by arrangement

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Equipment and technical data: Travel paths: - X-axis: 2,685 mm - Y-axis: 1,095 mm - Z-axis: 140 mm Milling unit: - 6 kW, water-cooled - Tool holder: HSK 63 F - Speed: 1,000 - 18,000 rpm Ledpswka H Eefx Adwjhb Tool changer: 6-position, side-mounted Drilling head: - 9 vertical drilling spindles, 32 mm pitch - Horizontal spindle: 1+1 - Vertical spindle: 1+1 Grooving saw in X direction Control: Twin CAM 32 Vacuum pump: 100 m³/h Includes vacuum suction cups Dimensions: 5,200 x 2,843 x 1,855 mm Weight: approx. 3,500 kg Availability: by arrangement Storage location: Röllbach