Used Double Sided Press for sale (37,275)

Condition: used, Machine not operational - control system not functioning Available at a special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Factory No. 300487, Year of Manufacture 2006 Pressing force: 500 tons Distance between columns (front and rear): 2520 mm Table area: 2500 x 2500 mm Nsdodzqptjpfx Ahnjlf Ram area: 2500 x 2500 mm Ram stroke: 600 mm Maximum installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable forward speed: 100-800 mm/s Pressure build-up to 5000 kN: approx. 0.7 sec. Return stroke speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking in the top dead center position - Adjacent control cabinet (200 x 50 cm) - Electrical control system SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7") - 2-hand control panel located beside the machine - Floor-level installation - Table top 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication system - Operating manual with circuit diagrams Space requirement (L x W x H): 372 x 260 x 460 cm Space requirement for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: new, Year of construction: 2019, pressing force: 275 t, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm Nedpfxsfxyigj Ahnelf :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec :2-50 mm/sec. Cylinder hub:900 mm Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar

Condition: excellent (used), drying rack for drying parts after painting double-sided length of shelves 780mm Nsdpfsvbf Ecex Ahnjlf maximum distance 2520mm minimum distance 350mm 22 shelves bars covered with rubber mobile construction clearance between bars 115mm

Condition: used, Year of construction: 1987, pressure 800 t Nlodpezl E Saofx Ahnjf stroke 100 mm no. of strokes 45 /min distance between columns 600 mm table surface area 560 x 650 mm capacity of ejector 5 t ejector stroke 15 mm ram surface 590 x 450 mm power requirement 22,0 kW Weight 17,0 t dimensions (WxDxH) 1,7 x 2,55 x 3,1 m Nominal force travel 1,46 mm With knuckle-joint drive, flywheel brake, hydraulic clutch with 2nd brake, press frame balancing, single ejector in table, self-monitoring control

Condition: used, Year of construction: 2005, Pressure 600 t distance between columns 2600 mm stroke 900 mm Nedezrptzepfx Ahnslf Distance table/ram, max. stroke up, adjustment up 1600 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 250 t Die cushion stroke in table 400 mm Die cushion area in table 2300 x 1300 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 160 mm Die cushion area in ram 1900 x 1300 mm Ram surface 2500 x 1730 mm Side window 1100 mm Oil volume 3500 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m Height above floor 6,4 m year of manufacture 1974 - overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition - Video at seller’s site before dismantling available

Condition: excellent (used), Year of construction: 2010, I sell the automatic drilling machine KUSING. Working width up to 1200mm Magazine for elements Nlodpjt I U E Ijfx Ahnef Configuration: 1+1 motors from sides Atypic 2-spindle drilling heads included 2 x 32mm. Drilling heads in price. Very good condition. Available immediately.

Condition: excellent (used), LINE (half line) of Double-side Sizing-Milling & Edge Banding, with automatic handling system. Composed of the following machines: A) LOADER (Portal) with double station "RBO" Mod. Advantage C 3200 and central motorized rollers table. B) Infeeding Rollerway, with double-cone TURNING Device "RBO" Mod. GPK-1 C) Double-side SIZING and EDGE BANDING machine "BIESSE" Mod. Stream SB2 11.0 Nljdpfohvah Njx Ahnsf D) UPSIDE DOWN 180° TURNING MACHINE "RBO" Mod. Ribaltatore E) Outfeeding Rollerway, with double-cone TURNING Device "RBO" Mod. GPK-2 F) STACKER (Portal) with double station "RBO" Mod. Advantage SC 3200, with central motorized rollers table.

Condition: used, Year of construction: 2010, pressure 600 t distance between columns 3640 mm stroke fix 350 mm Nedpfxezrppcj Ahnelf no. of strokes 11 - 44 /min dayligth (stroke and adjustment up) 1550 mm column travel -side 2200 mm table surface area 3600 x 2500 mm ram surface 3600 x 2500 mm ram adjustment 400 mm band width 2000 mm material thickness 0,6 - 2,5 mm material cross-cut 1600 x 2,5 mm² coil weight 35,0 t Number of Straightening rolls 13 0 straightening roll diameter 50 mm Blanking Line (press, coil line, blank stacking system) yom 1993 - 2010: new control Siemens S 7 - press Schuler type EBS 4-600 with infinitely variable drive, fly-wheel brake, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, ram interlocking moving tables (2x) without rails for the moving tables - decoiler make Schleicher, type HE - 355 - 2100, yom 1994 with auxiliary drive, snubber roll - coil lifting device - extractor device make Schleicher - shear - straightening machine make Schnutz, type RME 18/50/13-2000 TZ, yom 1994 with infinitely variable drive, 30 intermediate rolls, 117 supporting rolls - coil loop bridge - roll feed make Schleicher, type WV-SYS-A 160-2000, yom 1994 - blank stacker NSM-Magnettechnik stored in dismantled condition - Video before dismantling available

Condition: used, SECOND-HAND DOUBLE SIDED CUTTING OFF MACHINE FOR CHAIR ELEMENTS MOD. TECNOSYSTEM Nlodpfswr T I Ssx Ahnef

Condition: used, Year of construction: 1973, pressure 1000 t distance between columns 4150 mm stroke 1200 mm distance table/blankh.,max. stroke up,adjustm. up 2100 mm table surface area 4000 x 2200 mm die-cushion pressure inside the table 360 t stroke of drawing cushion in table 300 mm die-cushion pressure in pusher 100 t stroke of drawing cushion in pusher 150 mm ram surface 4000 x 2200 mm column travel -side 1300 mm die-cushion inside the table hydraulic, controlled die-cushion in pusher hydraulic, controlled Cut Shock absorption hydraulic Control Siemens S7 height over floor 7,7 m total power requirement 300 kW weight of the machine ca. 280 t dimensions of the machine ca. 5,75 x 4,3 x 9,55 m Year of construction 1973 Modernization 2005 Njdpfxeynmm Se Ahnjlf with oil-hydraulic drive, hydraulically controlled drawing cushion in the table and Ram, hydraulic cutting impact damping stored dismantled - short video available from the seller before dismantling

Condition: used, pressure 200 t distance between columns 1600 mm max. ram stroke 600 mm dayligth 900 mm table width 1600 mm table depth 1300 mm table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 rapid traverse 400 mm/s return speed 325 mm/s pressing speed 42 mm/s bei 40% mm/sec pressing speed 20 mm/s bei 100% mm/sec Njdsg S R Twspfx Ahnolf die-cushion pressure 800 kN die cushion stroke 150 mm speed of die cushion auf 68/ ab 225 mm/s

Year of construction: 1976, condition: used, pressure 100 t distance between columns 625 mm stroke 150 mm table surface area 580x450 mm ram surface 580x340 mm hole in the table Ø 150 mm table height 850 mm Nsdpfx Aholp U Eujnslf tool hole in ram Ø 45 mm column travel -side 200x200 mm weight of the machine ca. ca. 6,0 t dimensions of the machine ca. BxTxH ca. 1300x1300x2750 mm

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 700 mm, pressure:160 t distance between columns:700 mm Nlodofxyh Repfx Ahnjf stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :600 mm Ram plate:700 x 600 mm table height over floor:850 mm Table size:700 x 600 mm speed of forward flow:10 mm/sec Pressing speed:10 mm/sec :10 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,2 t dimensions:950 x 2440 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück heating plates :550 x 500 mm :6800 ? :2400 ? :1200 ? :1200 ?

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 550 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :550 mm Ram plate:700 x 600 mm table height over floor:900 mm Table size:700 x 600 mm speed of forward flow:50 mm/sec Pressing speed:10 mm/sec :50 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,3 t Nodpsfxygpsfx Ahnslf dimensions:1150 x 2600 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück Heating panels (L x B) with 2 measuring sensors diagonally:550 x 500 mm Siemens Control System:S7 1200 Monitor:12 Zoll :2400 ? :1200 ? :1200 ?

Condition: excellent (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Panels thickness (min/max) mm 10 / 60 Working width (min/max) mm 230 / 1600 (ca.) Nledpfx Ael Hydmjhnof Numerical Control / Software WinEdge Adjustable feeding speed (m/min ) 10 - 30 Safety and sound-proof enclosures/cabins SIZING PART (for each side): No. 2 Hogging Units (2 x Kw 5,8 ca.) No. 2 Milling units (2 x Kw 4 ca.) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt glue + Multing Unit) Pressure zone (adjustable by CN) Edge coils supporting unit (No. 6 reels) Rough Trimming unit (2 x Kw 1 ca.) Fine Trimming unit 08.055 (2 x Kw 0,5 ca.) 0°-30° No. 5 Milling grooving units (5 x Kw 4 ca.) Profile Scraping unit Glue scraping unit Spraying Unit (for polishing liquid) Buffing unit + Hot Air Heater (to reactivate the color of plastic tape)

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips/lippings (Min/max) mm 3 / 10 Panels thickness (min/max) mm 8 / 60 Working width (min/max) mm 236 / 3300 Numerical Control /Software ICOS Open Adjustable feeding speed (m/min ) 10 - 50 - Without Transmission bar (Master & Slave system) Distance (center-axes) of the Disappearing Dogs (mm) 1080 SIZING PART (for each side): Anti-chipping Milling Unit 75.186 (1 x Kw 4,4) Hogging Units (2 x kW 8) Free Space (for Milling unit) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue) 04.1570 + 283.205 Band Pressure zone - Edge coils supporting unit (No. 6 reels) Snipping (end-cutting) unit 08.42 (2 x Kw 0,66) speed 30 m/min (0° - 25) Fine Trimming unit 08.055 (2 x Kw 1) / 0° - 30° Multi Function Unit (Profile contour Trimming unit) 08.342 (2 x Kw 0,66) with servo-motors Profile edge scraping unit 08.519 Glue scraping unit 08.521 Spraying Unit (for polishing liquid) Buffing unit 08.617-4 (4 x Kw 0,18) Milling grooving unit 08.190 (1 x Kw 4,5) 90°-180°-270° Nljdpfx Ajd Nt Rqehnjf

Condition: used, Machines for export from company closure Stock No. 62506 = RAPID Type DGL 5000 / 500 double mitre saw = Weight approx. 1,200 kg = Special price EUR 1,800 Stock No. 54183 = MÜLLER hydraulic press 10 ton, without hydraulic pump = Weight approx. 1,200 kg = Special price EUR 1,000 Stock No. 57780 = MÜLLER hydraulic press Type HEP 40 = Weight approx. 2,200 kg = Special price EUR 1,900 Hydraulic press – separate hydraulic power unit = Weight approx. 3,000 kg Stock No. 60507 = WEBO drill with 4 spindles = Weight approx. 1,900 kg = EUR 1,600 Stock No. 57592 = ALZMETALL drill with 2 spindles = Weight approx. 1,700 kg = EUR 1,200 Stock No. 60699 = WEBO column-type drill MK5 = Weight 1,600 kg = Special price EUR 1,600 Stock No. 60177 = WEBO radial drilling machine Type R4bR = Weight approx. 2,800 kg = Special price EUR 1,900 Nedpfx Ahjy Erzdenolf Stock No. 57432 = GILDEMEISTER Type GD 160 = Weight approx. 4,000 kg = Special price EUR 1,900 --- Many more machines in stock, available for immediate export. For example: 10 units welding machines, CLOOS, ESS etc. 2x HITACHI SEIKI CNC lathes

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm Nedpfxovprv Re Ahnjlf rapid traverse 22 mm/s stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company.

Condition: excellent (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Panels thickness (min/max) mm 8 / 45 (60) Working width (min/max) mm 236 / 1300 Numerical Control / Software ICOS Open (Windows base) Adjustable feeding speed (m/min ) 10 - 50 Safety and sound-proof enclosures/cabins Nedsunrwnepfx Ahnjlf SIZING PART (for each side): Hogging Units 75.30 (2 x Kw 6,6) Free space EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) 04.1570 + 283.201 Pressure zone Edge coils supporting unit (No. of reels) 6 Rough Trimming unit 08.055 (2 x Kw 1) 0°-30° Fine Trimming unit 08.055 (2 x Kw 0,66) 0°-30° Profile Scraping unit 08.515 Free space Buffing unit 08.617-2 (2 x Kw 0,18) Nr. 2 Milling grooving units RIGHT: 75.30 (2 x Kw 4,4) 90°-180°

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 - 3 Edges thickness in stips / lippings (min/max) option: mm 20 Panels thickness (min/max) mm 10 / 60 Working width (min/max) mm 250 / 3000 (ca.) Adjustable feeding speed (m/min) 12 - 40 m/min (ca.) Safety sound-proof enclosures/cabins Distance (center-axes) of Disappearing Dogs (mm) 500 Nledpsk Nk R Dsfx Ahnsf SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Anti-chipping Milling Unit (1 x Kw 4 (ca.)) Hogging Units (2 x Kw 5,8 (ca.)) Milling-Shaping unit 1 x Kw 4 (ca.) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue + Quick Melt system) Edge coils support (No 2 reels) + Band Pressure zone Snipping (end-cutting) unit (2 x Kw 0,35) ca. Rough Trimming unit (2 x Kw 1) ca. Fine Trimming unit (2 x Kw 0,5 ca.) 0°-30° Multi Function Unit (Profile contour Trimming unit) with 2 revolvers (8+8 folds) - max 27 m/min Milling grooving unit 1 x Kw 4 (ca.) (0° - 90°) Profile Scraping unit + Glue scraping unit + Buffing unit

Condition: new, Year of construction: 2026, pressing force: 30 t, DURENDUS 30 T Heated Press – Double Column Press – 700 × 500 mm Heated Plates, Sliding Table The machine shown here was already built and delivered to a customer. We can manufacture this machine for you again on very short notice—customized to your individual requirements if desired. This is a hydraulic heated press with electrically heated plates and a manual sliding table for pressing, laminating, and forming processes involving heat. Base price: €42,000 net Options (on request): The listed options are based on completed customer projects and allow targeted customization of the machine to the specific application. The base machine provides a functional standard configuration—in practice, it is often supplemented with additional features and configured according to project requirements. ==== Technical Data + Information: ==== General Information * Design: Double column press * Pressing force: 30 t (adjustable) * Total weight: approx. 3,200 kg * Overall dimensions (W × D × H): 2,000 × 1,500 × 2,850 mm ==== Working Area * Table size: 700 × 500 mm * Heating plates: 700 × 500 × 65 mm * Installation height: max. 800 mm * Table stroke: 500 mm (manual) ==== Table & Ram * Ram stroke: 600 mm * Cylinder diameter: Ø 130 mm * Piston rod: Ø 80 mm * 8-point slide guide for parallelism ==== Speeds Nodpfoy H Dtzex Ahnelf * Working speed: 9 mm/s * Return speed: 25 mm/s ==== Hydraulics & Drive * Working pressure: max. 240 bar * Pump output: 12 l/min * Motor power: 3 kW * Hydraulic tank: 80 l * Pressure accuracy: ±5 bar * Hydraulic system with air cooling ==== Control & Operation * SIEMENS S7-1200 control with 7" touch panel * Programmable parameters (stroke, pressure, time, cycles) * Two-hand operation * Electrical connection: 400 V / 50 Hz * Total connected load: approx. 25 kW (including heating) ==== Equipment * Electrically heated press plates up to 200 °C * Temperature monitoring with sensors * Passive pressure holding function up to 60 minutes * Hydraulic and electronic overload protection * Safety limit switches * CE certification * Dual-layer paint finish according to RAL ===== Hot pressing, laminating, plastics processing, rubber and composite material processing, forming press applications Heated press, hydraulic press, double column press, thermo press, laminating press, industrial press Are you looking for a hydraulic press tailored to your application? Contact us for a customized quotation. Our hydraulic presses are manufactured in compliance with German and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they fully comply with the Brazilian National Safety Directive NR 12, which is based on and extends these standards. Our key strength lies in special purpose machine construction and press automation. We offer custom-built hydraulic presses at surprisingly affordable prices. For the hydraulics, we primarily use components from leading European manufacturers.

Condition: used, Year of construction: 1976, wire diameter: 3,0 - 5,5 mm Nsdokk Exepfx Ahnolf nail length: 15 - 80 (100) mm output: 300 St./min.

Condition: used, Year of construction: 1978, pressure 160 t no. of strokes 40 - 120 Hub/min sheet width mm total power requirement 40 kW Pressing capacity 160 ton Table clamping area 1,100 x 1,280 mm Ram clamping area 850 x 890 mm Distance between guides 1,120 mm Distance between columns (below guide ways) 1,350 mm Distance between Table and ram in upper position approx. 400 mm No. of strokes 40 - 120 /min Adjustment of stoke 67 / 115 / 160 mm Ram adjustment, motor driven 125 mm Ejector travel 50 mm Nlsdpfxst Hwz Nj Ahnsf Total electrical load, approx. 40 kW - 500 V - 50 Hz Weight, approx. 24,000 kg Accessories / Special Features * WEINGARTEN Sheet Metal Uncoiler with overhead loop control (space saving because it does not need a loop-pit). Strip width 375 mm. The loop control guides the strip-material from the uncoiler to the machine thru a straightening device with automatic supervision. * 8-track slide bearing guide. * Automatic oil-circulation lubrication. * Hydraulic overload protection in conjunction with the ORTLINGHAUS Clutch Brake * Safety doors. * Motor-driven ram adjustment 125 mm. * Required space: 4 x 2.2 m. Height max. 4.6 m (only press)

Condition: used, Thrust: 400 TON. Barbed points: no. 2 Model: AF 400 MB 30-60 Year of construction: 1992 Table size: 3,000 X 1,600 mm. Slide size: 3,000 X 1,600 mm. Front passage: 3,000 mm. Side passage: 1,200 mm. Slide registration: 150 mm. Strokes per min: 20- c/min. Nodpfx Asq N Er Djhnelf Stroke : 500 mm. Mold clearance at PMI: 1,118 mm. Main motor power: 30 kw Hydraulic Safety: present Weight: 82 ton.

Condition: used, machine/vehicle number: 008430, Position 1: Panel Feeding and Loading MAHROS + STEFANI-RUNNER + EVOLUTION Position 2: Double Sided Squaring/Edgebanding Machines MAHROS + STEFANI-RUNNER + EVOLUTION Position 3: Panel Stacking and Offloading MAHROS + STEFANI-RUNNER + EVOLUTION Nedpfjyqxx Ssx Ahnslf