Used Dowel Insertion for sale (2,174)

Condition: used, Year of construction: 1989, Used machine Year of construction: 1989 Drill beam: 19 spindles Working width: 630 mm Gantry passage: 710 mm Drilling stroke: 120 mm Position adjustment drilling unit: 0-45 mm Hole row position adjustment: 0-150 mm Spindle speed: 2800 rpm Djdpfx Adew Nac Nodowf Shank diameter of the drill: ø10 mm Clamping height of the workpieces max. 100 mm Motor: 1.5 kW, 380 V, 50 Hz Working height: 850 mm Compressed air connection: 6 bar Weight: approx. 310 kg Availability: short term Storage location: Baden-Württemberg

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Dsdpju Rwa Ijfx Addowf Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: ready for operation (used), Dowel Cutting and Chamfering Machine Manufacturer: Löser Type AA 200 Dwsdpfowmpvhjx Addef Table-top machine for the production of wooden dowels, for the efficient cutting and chamfering of dowel rods/round bars. The Type AA 200 Dowel Cutting and Chamfering Machine is a low- to medium-performance machine. It can cut and chamfer round bars made of wood, plastic, laminated paper, and other materials. The dowel length is adjustable between 20 and 150 mm and is determined using a setting scale. The chamfer thickness can be adjusted as required. The machine is equipped with a magazine ring as standard. This allows the operator to operate several machines simultaneously or perform other tasks. The machine features a solid, torsion-free cast iron stand. Extremely easy operation, simple maintenance, and easily accessible lubrication points are further advantages of this machine. Technical specifications: For dowel diameters approx. 6-13 mm Minimum cutting length: 15 mm Largest cutting length: 150 mm Output: approx. 2,000 pieces per hour Weight: 53 kg (tabletop machine) Including adapters for dowel diameters 8-9 mm, 10-11 mm, and 12-13 mm. The pinion and chain have been replaced.

Condition: used, No. 3238 Dowel drilling machine Gannomat Combi RB 110 Used Precision universal dowel drilling machine for drilling holes in carcasses, frames, fittings and rows of holes in system 32 The table can be pneumatically swiveled 90° together with the drill beam Short workpieces can be inserted upright Easy drilling of pot hinges and connecting fittings Drilling of miter and flat frames Drilling from below Drilling of longitudinal and transverse friezes at the center stop Fully automatic pneumatic control with control panel Working width 800 mm Drill beam 23 spindles, Pitch 32 mm Drilling stroke 75 mm Position adjustment of drilling unit 0 - 60 or 110 mm Spindle speed 2800 rpm Shank diameter of drill bit 10 mm Maximum clamping height of workpieces 80 mm Motor 1.5 kW, 380 V Compressed air connection 6 bar Weight approx. 450 kg Sale on behalf of the customer, ex location near 69124 Heidelberg, without disassembly, without transport and assembly Disassembly, loading and transport by us optionally possible Errors in description and price excepted To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Dsdew Id T Nspfx Addjwf Sold as is Technical information, description of condition, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Year of construction: 1966, operating hours: 10,000 h, condition: excellent (used), functionality: fully functional, outer diameter: 420 mm, machine/vehicle number: 58256, Nebiolo Saturnia in very good condition. From first owner, at first used as a letterpress in the upcoming market with offset in the 70's. The company always produced with it's offset to maxima 50/70 size. Situated as a local printer in a village, the Nebiolo was sometimes used for rilling, slitting, scoring some offset jobs. very good machine, low noise, excellent condition of al mechanical parts. Airpump for feeder and delivery is for a later make = Becker dry-pump 100m3 with low noise. All parts necessary for the machine come with the machine, even as the original operational book and spare-parts book. The cylinder has a 6 cm larger diameter than a KBA Condor and it weights 800kgs, only 200 kgs less of that of a heidelberg SBB/SBD. The delivery is different and for carton better that that of its competitors: a triple drum delivery, turning the front side up again on the belts which transport it to the pile. Best is to replace the individual belts for one large belt and make some extra attention for laying the sheets down when coming from the belt with better air facilities. Of course we can arrange that for you either. Then you have a faster, very easy to operate and maintain with better productivity and at least the same durability (with lower noise-level due to less moving parts) than an heidelberg SBD with approx the same size for more than double the money. Really a nice product from Nebiolo even as it big brother Urania. They have pull-lays but can easily turn over to push side lays. Some specs: Dsdpfxetyyvwe Addowf Max paper size 650 x 950 mm Min paper size 300 x 420 mm Speed 1500 - 4000 imp/hour Feeder pile height 550 mm Delivery pile height 650 mm Impression force approx. 35000 N (not adjustable in lighter or heavier, only one value) Bearer height 24,85 mm; machines needs "normal - Bobst standard" 23,80 diecut forms/lines with a hardened steel plate under the form so that small compensations could be made with thin band and paper under this hardened plate. This is the only and best method. A 45 to 47 HRC plate will be delivered with the machine, even as a new cylinder jacket. Feeder and delivery use an additional extern pump, Becker, 100m3, 2kW Size of the machine (approx, with steps) L x W x H = 330 x 220 x 190 cm Weight net 4,800 kgs

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1320x1220x1400 mm Weight 275 kg Total power requirement 1,5 kw Dedpfxsvz Eibj Addowf

Condition: used, Used machine For drilling dowels into flat or end faces With roller-bearing drill shaft and conical claw coupling Driven by any hand drill Working width 650 mm With 7 drill shafts Pivoting drill beam 0° - 45° - 90° Clamping height 80 mm Dsdpfx Ajw Nacieddowf Minimum drill hole spacing 30 mm Availability: Short-term Storage location: Flörsheim

Condition: used, 2-axis removal machine, inserter, servo robot, workpiece gripper, pick-and-place machine, removal robot Removal device, handling device for presses, lathes, etc. GETECHA Type GL-20S No. 13836 Year of manufacture 10/2003 Z-axis travel 1900 mm Travel distance Y-axis 250 mm Travel speed Z-axis max. 1100 mm/sec. Travel speed Y-axis max. 227 mm/sec. infinitely variable travel speed in Y- and Z-axis via SMB servomotors - precise axis movement via linear guides - epis control system - Control panel opposite - Control for conveyor belt, gripper magnets, bead breaker cylinder, vacuum, gripper - External monitoring inputs for emergency stop, press open, press closed, safety doors closed, automatic - Mounted gripper with 3 lifting magnets, 3 pneumatic push-off cylinders (30 mm stroke), 1 pneumatic clamping cylinder (40 mm stroke) - Operating hours 25998 hrs. Dwjdpfxoharwys Addsf The system was used as an inserter/removal device on a press. Space requirement L x W x H 2900 x 1800 x 2000 mm Weight approx. 800 kg good condition

Condition: used, HIGH SPEED DOWEL CROSS-CUT AND CHAMFERING MACHINE LOSER MOD. AA220 Dwsdpfx Ajqpdkcsddsf - Range of working diameter: 6 - 18 mm - Capacity: about 7,500 - 15,000 dowels/hour

Condition: used, Year of construction: 1979, machine/vehicle number: 4015, Spiraleindrehmaschine - Spiral insertion machine Renz DPSTYear 1979 - Serial-No. 4015 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect Dwodpfeh Axnyox Addjf On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Scheer Type DB 5 dowel hole drilling machine for precise and fast drilling of dowel holes (horizontal and vertical) in solid wood and panel materials. The machine is ideal for series production in furniture construction as well as for precise joints in interior design. Includes a comprehensive range of dowel drill bits. drilling spindles: 21 division: 32 mm passage width: max. 1.000 mm Dedpfswp E Uxsx Addowf Pivot: pneumatic

Condition: good (used), Year of construction: 1989, functionality: fully functional, We sell an automatic hinge installation device. Device from 1989. Siemens controller and Simatic panel installed on the device in 2015. Hinges were installed on the outer frames of the Wood-Aluminum window with the device. Dodpfx Aju Hxtuoddewf Device is in good condition. The price of the device is to be offered by the buyer. Buyer is responsible for transportation and dismantling. If you have any further questions, please contact us about the production equipmen

Condition: used, Year of construction: 1997, Used machine Year of construction 1997 Universal dowel drilling machine with drilling from below heavy cast iron table pneumatic swivel device; effortless changeover from vertical to horizontal or to any miter angle Drilling unit with digital positioning for 0-edge transfer, touch stops are used which transfer the tool thickness to the vertical bore during horizontal drilling Dedjw Naa Uspfx Addswf to the vertical bore for hole line drilling, the stop system is slid into guides on the side of the machine table Working width 700 mm Portal passage max. 850 mm Drilling depth max. 80 mm Operating pressure 6-8 bar Motor 1.9 kW Spindle speed 2800 rpm 21 spindles pitch 32 mm Spindle distance min. 32 mm Spindle distance max. 640 mm Space requirement L X W x H 960 x 630 x1140 mm Weight approx. 300 kg Availability: short term Storage location: Flörsheim

Condition: used, Dowel drilling machine, dowel drilling machine, drilling and dowel station, row of holes dowel drilling machine, knothole drilling machine, row drilling machine, drilling beam, multi-spindle drilling head, articulated multi-spindle head, row drilling machine, dowel drilling head, dowel drilling machine, drilling gear -Workpiece clamping; pneumatic -Number of drills: 21 pieces. 32 mm grid -Bore head: swiveling -Bore depth: max. 80 mm -Height adjustment: max. 80 mm Dwjdpfx Aof Dluroddsf -Underframe: transport castors that can be steered on 4 pieces -Dimensions: 1090/1330 / H1460 mm -Weight: 433 kg

Condition: excellent (used), Dowel Drill DB12 1.1 kW 8 mm Stroke Dsdowmbpmepfx Addowf 3 Spindles

Condition: good (used), Year of construction: 1984, Dowel Drilling Machine AYEN SKB 50 Manufacturer AYEN Model SKB 50 Year of manufacture 1984 S/N 8411346 Total 50 spindles in (2) swivel heads with (25) spindles each drills vertically from above and horizontally from behind drills in any angle between 0° - 90° with a positive stop at 45° working width 768mm / passage 1000mm 50-spindle swivel head assembly quickly converts to (2) 25-spindle heads for double row drilling, 5-1/8" minimum distance between heads for row drilling. Dsdpekcfcaofx Addjwf 3 HP - 3,450 RPM gear motor, 39" plate width with a 30-1/4" drilling width. Complete with: (2) 39" stops with flip stops, (3) pneumatic "Quick Set" hold-downs, Foot pedal control for drill cycle/head positioning. Motors, 3 phases, 380 V / 50 Hz Compressed air consumption 9l / cycle Weight 490 Kg

Condition: used, Electro-pneumatic universal dowel hole drilling machine Scheer type DB4 for precise drilling of dowel holes in wood materials. The machine enables efficient and precise work thanks to several synchronously working, horizontal and vertical drilling spindles. Ideal for furniture and interior construction as well as for series production in woodworking. division: 32 mm Dedpfx Adov Hnr Asdjwf drilling spindles: 2 x 25 Spindle distance: max. 768 mm

Condition: reconditioned (used), Year of construction: 1997, functionality: fully functional, Schleicher 3 unit drilling machine after lignum renovation. Dwjdpfjt Ndznsx Addef Machine equipped with upper units 3 pieces .Pneumatic pressure .Working realized by forcing the button unit the rest of the automatic .Choice of units possible each one or all .Speed and depth of drilling the possibility of setting .Machine after major repair .New electricity and driver .Net price vat invoice warranty one year .The machine can be additionally equipped with rulers bumpers pressures and drilling heads of any spacing .

Condition: used, Used machine Condition: age-appropriate for efficient dowel hole drilling of longitudinal and transverse pilaster strips for frame doors, door panels Dwjdew Nabxepfx Addof drawer parts crossbars of all kinds 3 spindle motor bung spacing 25/25 mm stroke max 80 mm Motor 1,5 HP Support table 260 x 130 mm Height adjustment from 5-40 mm according to scale with reversible folding fence Foot valve control NRW

Condition: used, Dowel drilling machine, dowel drilling machine, drilling and dowel station, row of holes dowel drilling machine, knothole drilling machine, row drilling machine, drilling beam, multi-spindle drilling head, articulated multi-spindle head, row drilling machine, dowel drilling head, dowel drilling machine, drilling gear -Drive: 1.5 / 2.0 kW -Drill speed: 2200/4400 rpm -pneumatic workpiece clamping -15 drill bits from below, grid 32 mm Dodpfscuh D Rsx Addjwf -Bore head: swiveling -Foot switch -Bore depth: max. 185 mm -Height adjustment: max. Mm -Max. Clamping height: 110 mm -Dimensions: 950/1100 / H1350 mm -Weight: 616 kg

Condition: used, New, unused and used dowel hole drills as shown. length: Miscellaneous diameter: Miscellaneous Shank: predominantly 10 mm Dwjdovy Alkjpfx Addjf mass: 4,7 kg

Condition: new, Year of construction: 2022, New machine Year of manufacture: 2022 DESCRIPTION 21 drilling spindles with quick-change system; five quick-change chucks included in delivery Heavy-duty steel worktable; five quick-change chucks included in delivery Dwodpew I Uqljfx Addef Patented system for fast and easy adjustment of drilling depth via spiral disc Pneumatic drill head swiveling, allowing drilling in any position between 0° and 90° Fold-down cast iron side stops with round bar guide Side stops easily adjustable and lockable to millimeter scale using magnifier Height adjustment of drill head via counter Two positionable pneumatic clamping cylinders With a spindle center distance of 640 mm, it is possible to process two workpieces of 316 mm width each SCOPE OF DELIVERY Two pneumatic pressure cylinders Five quick-change chucks Two stop rails, each 1.5 m long Four fold-down stops for the stop rails One setting gauge for fine adjustment of the fold-down stops on the stop rails TECHNICAL DATA Dimensions and Weights Worktable length 885 mm Worktable width 332 mm Product length approx. 1015 mm Product width/depth approx. 990 mm Product height approx. 1270 mm Net weight approx. 260 kg Electrical Data Rated input power 1.5 kW Delivered power 1.1 kW Motor duty cycle S3 Connection voltage 400 V Mains frequency 50 Hz Noise Emission Sound pressure level 78.3 dB(A) Pneumatic Connection Working pressure 6 – 8 bar Spindle Maximum drilling width 640 mm Maximum drilling depth at 90°: 65 mm Number of spindles: 21 Spindle distance 32 mm Center distance first to last spindle: 640 mm Spindle spacing sufficient for two workpieces of 316 mm each Spindle speed: 2800 rpm Drill head swivel range: 0 – 90° Maximum workpiece height: 130 mm Extraction Extraction nozzle diameter: 80 mm Including optional accessories: 2 pcs. Additional pneumatic pressure cylinders for MDB 21/23/29 PRO 17 pcs. Quick-change chucks for MDB 21/23/29 PRO 1 pc. Setting gauge for rear fence distance for MDB 21/23/29 PRO 1 pc. Reference pin for line drilling for MDB 21/23/29 PRO Location: Solingen Availability: Immediately

Condition: used, Working width: 720 mm working width: 820 mm Dedpjlfcn Ejfx Addewf Max. passage: 45 mm Max throughput: 120 mm Drilling depth vertical: 45 mm, horizontal: 120 mm

Year of construction: 2025, condition: new, New machine Year of manufacture: 2025 Features and technical data: Standard configuration: - Robust machine base - Dowel system for: Dowel diameter 8 mm, Dowel length 35 mm (factory setting, adjustable from 30 to 40 mm), Dowel protrusion 12 mm (factory setting, adjustable from 7 to 20 mm) - Recoil-free gun - Vibratory feeder for dowel transport - Dowel diameter and length control with Auto-DL-Select system - Water supply system for pre-glued dowels - Water tank (stainless steel, 7.5 l) - Closed water system with 6 bar water pressure and spray nozzle Dsdpfx Adswx Aadjdowf - Electronic control with: - Main switch On / Off - Program selector switch Water / Water + Feeding - Potentiometer for dowel feed via vibratory feeder - Potentiometer for adjusting water injection quantity - Control lamp for indicating minimum water level in the water tank - Mobile base - Compressed air: 6 bar / Electrical: 230V, 1Ph, 50Hz HoKuTech DübelJet with option for opposing hole processing: 1 unit HoKuTech | DübelJet with upgrade kit for LeimJet including fixtures for attaching/connecting to the DübelJet including height-adjustable suspension for glue hose including: 1 HoKuTech | LeimJet Glue dispensing unit for opposing hole processing Viscosity for PVAc glues up to 75,000 mPas Includes dowel nozzle for Ø 8 mm, pointed nozzle Location: Flörsheim Availability: Immediately

Condition: new, Year of construction: 2023, New machine Year of manufacture: 2023 Multi-spindle universal dowel drilling machine with 3 CNC axes (+/- 0.1 mm) with horizontal and vertical drilling capability electronic adjustment of height, depth, and drilling angle (0-90°) with 7" color touchscreen with memory for up to 1000 programs Dwedpfx Adelk R Epjdsf with parallel fences with numerical adjustment with 21 drilling spindles (10 left, 11 right) Spindle spacing: 32 mm Maximum drilling distance: 640 mm Maximum tool diameter: 40 mm Maximum drilling depth: 65 mm Maximum horizontal drilling height: 35 mm Working height: 860 mm Maximum panel thickness: 60 mm Maximum panel size: 900 x 3000 mm Motor: 1.5 kW - 2800 rpm Pneumatic connection: 6/8 bar Compressed air consumption per work cycle: 5 NL Extraction port: 80 mm Machine footprint: 1580 x 950 x 1400 mm Net weight: 340 kg Availability: short-term Location: Flörsheim