Used Mori Seiki Sl for sale (189)

Condition: used, Year of construction: 1996, functionality: limited functionality, travel distance X-axis: 630 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 650 mm, controller model: Fanuc MSX-516, rotational speed (max.): 12,000 rpm, The P8 power supply, valued at €1,500, was only replaced in August 2024! The spindle was repaired in 2017 and has mostly only been used for single-layer operation since then! TECHNICAL DETAILS Travel range X-axis: 630 mm Travel range Y-axis: 600 mm Travel range Z-axis: 650 mm Feed length X-axis: 630 mm Feed length Y-axis: 600 mm Feed length Z-axis: 650 mm Table width: 500 mm Table length: 500 mm Number of pallets: 2 Maximum speed: 12,000 rpm Number of tool magazine slots: 60 (BT40) MACHINE DETAILS Control: Fanuc MSX-516 Fpedpozcuyisfx Adrsk Phases: 3 Frequency: 50 Hz Voltage: AC 200 V Full load current: 181 A Note: The rapid traverse rate of the X-axis is reduced by 20% to extend the service life of the telescopic guides. The sealing ring during pallet changes is likely defective. The seller temporarily resolved this by inserting a ball valve in between when the pallets needed to be changed. EQUIPMENT Documentation/Manual Chip conveyor

Condition: used, Year of construction: 2013, x-travel 600 mm y-travel 530 mm z-travel 510 mm Control M 730 BM MAPPS IV max. spindle speed 10.000 min/-1 power capacity - main spindel 15 / 11 kW tool taper SK 40 transmission ratio 1 spindle diameter in front bearing 80 mm table surface area 900 x 600 mm max. table load 800 kg T-slots 6x 18 x 100 mm distance spindle /table 150 - 660 mm number of toolpositions 30 pos. Fodpfx Adox R Enberspk tool taper SK 40 max. tool diameter 80 mm max. tool-dia with free toolbox 150 mm max. tool length 300 mm max. tool weight 8,0 kg change-time tool to tool ca. 1,3 sec change-time chip to chip ca. 3,45 sec rapid traverse ( X / Y / Z ) 30 m/min feed speeds 1 - 30.000 mm/min Tipp feed 0 - 5.000 : 20 mm/min total power requirement 30 kVA weight of the machine ca. 6,0 t dimensions of the machine ca. 4,5 x 3,5 x 2,7 m CNC - Machining Center Vertical MORI SEIKI - NVX 5060 II / 40

Condition: used, Year of construction: 2011, turning diameter max. 320 mm turning length max. 810 mm control MSX-701 IV greates pass round over bed 800 mm Swing dia. over traverse guideway 800 mm distance between spindles 1.130 mm Number of revolutions max. 5.000 rpm power capacity - main spindel 25 / 22 kW max. Torque 358 Nm spindle diameter in front bearing 120 mm spindle bore 73 mm max. usable bar diameter 65 mm Fpodpfx Adsv E R E Nerek C-Axis 0,001 ° spindle nose JIS A2-6 collet chuck 160 mm Number of revolutions max. 5.000 rpm power capacity - Sub spindle 25 / 22 kW max. Torque 358 Nm spindle diameter in front bearing 120 mm spindle bore 73 mm max. usable bar diameter 65 mm C-Axis 0,001 ° spindle nose JIS A2-6 collet chuck 160 mm number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 mm Shank diameter 20 x 20 mm Drill shank diameter 32 mm turret change time 0,18 sec. number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Shank diameter 20 x 20 mm Drill shank diameter 32 mm turret change time 0,18 sec. x-travel 1/2: 210 mm y-travel 110 mm z-travel 1/2: 810 mm Traverses Subspindle B: 870 mm rapid traverse ( X / Y / Z ) 1: 30 / 20 / 50 m/min rapid traverse ( X / Y / Z ) 2: 30 / - / 50 m/min Tipp feed 0 - 5.000 mm/min total power requirement 94 kVA weight of the machine ca. 8,3 t dimensions of the machine ca. 10,0 x 3,0 x 2,5 m CNC - Turning- and MillingCenter MORI SEIKI - NZ 2000 T2Y - Main- and Subspindle - 2 turrets, up and below - Y-Axis - 2x 16 driven tool positions

Condition: used, Year of construction: 2007, x-travel 560 mm y-travel 560 mm z-travel 630 mm Control MSX 701 III MAPPS Max. rpm 14.000 min/-1 power capacity - main spindel 18,5 / 11 kW max. Torque 120 Nm tool taper MAS BT 40 distance spindle center to table 80 - 640 mm distance Spindlenose and center of table 100 - 730 mm numbers of pallets 2 size of pallet 400 x 400 mm max. workpiece weight 400 kg max. workpiecediameter 630 mm max. workpiece height 900 mm change time of pallets 6,0 sec b - axis 0,001 ° number of toolpositions 60 pos. tool taper MAS BT 40 max. tool diameter 70 / (140) mm max. tool length 400 mm max. tool weight 8,0 kg rapid traverse ( X / Y / Z ) 50 m/min feed speeds 0 - 50.000 mm/min Tipp feed 0 - 1.260 mm/min Fjdpowbi Adjfx Adropk total power requirement 35 kVA weight of the machine ca. 9,8 t dimensions of the machine ca. 5,5 x 3,5 x 2,8 m CNC - Machiningcenter Horizontal MORI SEIKI - NH 4000 DCG - pallet-changer - Control options Program restart, cylindrical and spiral interpolation High-speed milling cycles, island and pocket milling cycles

Condition: used, Year of construction: 2008, turning diameter max. 320 mm turning length 810 mm control MSX 701 MAPPS III standard turning dia. 200 mm Main spindle: Number of revolutions max. 6.000 min/-1 power capacity - main spindel 22 / 18,5 kW Bar feed max. 52 mm spindle bore 61 mm Fpjdpfx Adstqmqworjk C-Axis 0,001 ° Subspindel: Number of revolutions max. 6.000 min/-1 power capacity - Sub spindle 22 / 18,5 kW Bar feed max. 52 mm spindle bore 61 mm C-Axis 0,001 ° Turret 1 + 3: number of toolpositions je 16 pos. Number of driven toolspositions je 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 (+65 / -45) mm Turret 2: number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 (+45 / -65) mm axis stroke: x-travel 1-3: 210 mm y-travel 1-3: 110 mm z-travel 1+3: 300 / 2: 810 mm total power requirement 90 kVA weight of the machine ca. 9,3 t dimensions of the machine ca. 4,5 x 3,0 x 2,5 m CNC - Turning- and MillingCenter MORI SEIKI - NZ 1500 T3Y3 - Main- and Subspindle - 3 turrets, 2x upper / 1x below - 3x Y-Axis - 3x 16-pos. tool-drive - incl. 28x collets - incl. Hainbuch changing device

Condition: used, Year of construction: 2010, turning diameter max. 320 mm turning length 810 mm Fjdov E R E Aspfx Adrspk control MSX 701 Number of revolutions max. 6.000 U/min power capacity - main spindel 22 / 18 kW max. usable bar diameter 52 mm C-Axis 0,001 ° spindle nose JIS A2-5 collet chuck 140 mm Number of revolutions max. 6.000 U/min power capacity - Sub spindle 22 / 18 kW max. usable bar diameter 52 mm C-Axis 0,001 ° spindle nose JIS A2-5 collet chuck 140 mm number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW Y - Axis 110 mm number of toolpositions 16 pos. Number of driven toolspositions 16 pos. Spindle speed - driven tools max. 6.000 min -1 power capacity - driven tools 7,5 / 5,5 kW x-travel 1/2: 210 mm y-travel 110 mm z-travel 1/2: 810 mm b-axis 900 mm total power requirement 86 kVA weight of the machine ca. 8,1 t dimensions of the machine ca. 8,0 x 3,5 x 2,8 m CNC - Turning- and MillingCenter MORI SEIKI - NZ 1500 T2Y - Main- and Subspindle - 2 turrets, up and below - Y-Axis - 2x 16 driven tool positions

Condition: ready for operation (used), Year of construction: 1998, - USED - 4-AXIS HORIZONTAL MACHINING CENTRE WITH PALLET CHANGER X-AXIS TRAVEL: 2000 mm Y-AXIS TRAVEL: 1300 mm Z-AXIS TRAVEL: 1200 mm SPINDLE: 60-6000 rpm; 30-37 kW; ISO 50 - BT PALLET: N.2 ; 1000X1000 mm Fjdpfjyvlx Dex Adrspk MAX ADMITTED LOAD: 3000 Kg TOOL MAGAZINE: CHAIN-TYPE ; 120 POS CONTROL UNIT: MSC 502 WEIGHT: 35200 Kg OVERALL DIMENSIONS: 5330 x 7720 x 3810 mm ACCESSORIES: HIGH PRESSURE COOLANT ; SWARF CONVEYOR ; RS 232 SERIAL PORT ; TOOL SETTER NOTE: MAX PIECE DIAMETER 2000 mm; MAX HEIGHT 1550 mm; MAX WEIGTH 3000 Kg

Condition: used, Year of construction: 2006, x-travel 600 mm y-travel 400 mm z-travel 400 mm control MSX 501 Mori Seiki table surface area 700 x 450 mm max. table load 350 kg number of T-slots 4 T-slot - width 18 mm T-slot - distance 100 mm Number of revolutions 12.000 U/min power capacity - main spindel 18,5 / 15 / 11 kW tool taper BT 40 max. Torque 110,5 Nm diameter of forward milling spindle bearing 70 rapid travel x/y/z 20.000 mm/min feed speeds 1 - 20.000 mm/min Tipp feed 15 Steps / 0 - 1.260 mm/min Number of Toolpositions in magazine 40 Pos. Fpodpfev Az Ucsx Adrok Max. mould width 80 mm max. tool-dia with free toolbox 125 mm max. tool length 250 mm max. tool weight 8 kg change-time chip to chip 2,8 sec change-time tool to tool 1,0 sec total power requirement 34 kVA weight of the machine ca. 7,2 t dimensions of the machine ca. 2,8 x 3,0 x 2,9 m Machining Center Vertical MORI SEIKI - NV 4000 DCG - ca. 14.000 Operating-Hours

Condition: used, Year of construction: 1998, x-travel 1.020 mm y-travel 510 mm z-travel 510 mm control MSC 501 Fanuc Fjdpfxey Apcyo Adropk table surface area (APC) 1.200 x 480 mm max. table load (APC) 550 kg turning speed range - milling 10.000 U/min power capacity - milling spindle 22 / 18,5 kW tool taper BT 40 number of toolpositions 30 pos. tool taper BT 40 max. tool diameter 80 mm max. tool-dia with free toolbox 125 mm max. tool length 300 mm max. tool weight 8 kg rapid traverse 32 m/min feed 1 ~ 16.000 mm/min Tipp feed 0 ~ 1.260 mm/min spindle bearing diameter 85 mm total power requirement 59,5 kVA weight of the machine ca. 6,9 t dimensions of the machine ca. 3,9 x 2,7 x 2,9 m CNC - Machining Center - Vertical MORI SEIKI - SV 500 B/40 - Clamping devices are NOT included in the scope of delivery

Condition: excellent (used), functionality: fully functional, Fixed tool holders Machine: MORI SEIKI SL2000 Turret manufacturer: SAUTER ---- 2x→ No. 444-119 Turning Tool Holder 25 mm steel holder Fixed turning tool holder Price: on request ----- 1x→ No. 444-201 Double Turning Tool Holder for main spindle and sub spindle with 1x clamping bar for 25 mm tool steels Fixed turning tool holder Price: on request ----- 1x→ No. 444-210 Boring Bar Holder Cylindrical mount ø 32 mm second mount ø 32 mm; 57 mm to the rear Price: on request ----- 1x→ No. 444-205 Turning Holder Mount 25 mm steel holder Fedpfxeynb E Ne Adropk Price: on request

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, turning length: 920 mm, turning diameter: 400 mm, spindle speed (max.): 12,000 rpm, spindle bore: 65 mm, travel distance X-axis: 920 mm, rapid traverse Z-axis: 80 m/min, controller manufacturer: FANUC, controller model: 18iB, fuel: electricity, number of slots in tool magazine: 40, Equipment: chip conveyor, Mori Seiki Mod. MT 1500 SX 9-axis milling and turning machining center, manufactured in 2006, with Fanuc Series 18iB (MSX-501) control, maximum length between chucks of 920mm, maximum diameter of 400mm, bore of 65mm, spindle speeds of 4000 and 6000 rpm for chucks and 12,000 rpm for milling. 12-position turret with motorized tools, Y-axis, B-axis +/- 120, C-axis 0.001, ATC 40 tools and chip extractor. In excellent working order and can be seen working in Portugal. Fpodpfjh Elp Eox Adrok

Condition: ready for operation (used), Year of construction: 1989, functionality: fully functional, machine/vehicle number: 1764, controller manufacturer: Fanuc, No minimum price – guaranteed sale to the highest bidder! Fpedpfxjy Sluqj Adrek MACHINE DETAILS Control: Fanuc EQUIPMENT Accessories as shown in the pictures

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 669, travel distance X-axis: 560 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, controller model: MSC 502, rotational speed (max.): 12,000 rpm, No reserve price – guaranteed sale to the highest bidder! Fedpfxjy R U Eco Adrjpk TECHNICAL DETAILS Travel X-axis: 560 mm Travel Y-axis: 510 mm Travel Z-axis: 510 mm Distance spindle center to table: 50 – 650 mm Distance spindle nose to table center: 100 – 610 mm Main Spindle Max. speed: 12,000 rpm Drive power: 22 / 18.5 kW Tool holder: MAS BT-40 Spindle bearing diameter: 70 mm Pallet Changer Number of pallets: 2 Pallet size: 400 x 400 mm Max. workpiece diameter: 580 mm Max. workpiece height: 650 mm B-Axis Switching time 90°: 2.5 sec Pallet changeover time: 6.0 sec Tool Changer Number of tool positions: 60 Max. tool diameter: 80 mm Max. tool diameter with adjacent magazine slots free: 125 mm Max. tool length: 300 mm Max. tool weight: 8 kg Tool-to-tool change time: 1.5 sec Chip-to-chip change time: 3.7 sec Rapid traverse (X/Y/Z): 32 m/min Feed rate: 1 – 24,000 mm/min Jog feed rate: 0 – 1,260 mm/min MACHINE DETAILS CNC control: MSC 502 Total power requirement: 63 kVA Dimensions & Weight Footprint approx.: 5.5 x 4.5 x 2.7 m Machine weight approx.: 9.0 t EQUIPMENT Documentation Chip conveyor Cooling device High-pressure coolant system Internal coolant supply Tool magazine: 60 positions Pallet changer Pallets: 2 Signal lamp B-axis Hydraulic unit Spindle oil cooler Note: Shaft for loading must be provided by the buyer.

Condition: excellent (used), Year of construction: 2006, x-travel 750 mm y-travel 210 mm z-travel 1150 + 100 mm control Fanuc MSX-701III Maximum turning diameter 660 mm Max. turning length 1498 mm Diameter over cross slide max. 400 mm number of spindle speeds 3000 U/min tool piece magazine with 40 Plätzen turret 10 Fach total power requirement 90 kVA Fpedpfx Adey Spuusrok weight of the machine ca. 26,6 t dimensions of the machine ca. 5301 x 2997 x 2788 mm

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, X-axis travel: 140 mm Y-axis travel: +/- 40 mm Z-axis travel (1+2): 450 / 410 mm Turning length: 750 mm Turning diameter over cross slide: 250 mm Turning diameter: 190 mm Distance between centres: 750 mm Max. bar diameter: 52 mm Spindle speed (max.): 4,000 rpm Main spindle speed range: 60 - 6,000 rpm Drive power - main spindle: 22 / 18.5 kW Max. torque: 198 Nm Counter spindle B-axis travel: 525 mm Feeds Feed rate X (1+2): 18,000 mm/min Feed rate Y: 6,000 mm/min Feed rate Z (1+2): 24,000 mm/min Feed rate B: 24,000 mm/min Fpjdpfx Aoyyupmsdrok Number of turrets: 2 Number of tool stations: 2x 16 pos. Shank height for square tool: 20 mm Shank diameter for drills: 25 mm Turret indexing time: 0.2 s Tool holder: VDI 30 Speed range - driven tool stations (max.): 6,000 rpm Drive power - driven tool stations: 5.5 / 3.7 / 2.2 kW Rapid traverse X (1+2): 18 m/min Rapid traverse Y: 6 m/min Rapid traverse Z (1+2): 24 m/min Rapid traverse B: 24 m/min Rapid traverse C: 400 rpm MACHINE DETAILS Control: MSX 501 Fanuc drives Machine is in excellent condition

Condition: refurbished (used), Year of construction: 1996, functionality: fully functional, travel distance X-axis: 420 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 250 mm, rapid traverse X-axis: 48,000 m/min, rapid traverse Y-axis: 48,000 m/min, rapid traverse Z-axis: 48,000 m/min, controller model: Mitsubishi Meldas MSC-802M, The MORI SEIKI TV-30 is a compact and precise vertical machining center, designed for drilling, tapping, and milling operations on small components. Manufactured in 1996, it is equipped with a Mitsubishi Meldas MSC-802M control and features characteristics ideal for high-speed light machining work, with an automatic tool changer and a well-sized table relative to its compact footprint. Fodpoxfaw Dsfx Adrepk General Technical Data Brand: MORI SEIKI Model: TV-30 Category: Vertical Machining Centers Year of manufacture: 08-1996 CNC Control: Mitsubishi Meldas MSC-802M Machine weight: 2 tons Machine Dimensions: Length: 1,200 mm Width: 1,720 mm Height: 2,260 mm Spindle Spindle speed: 8,000 rpm Spindle motor power (cont./30 min): - 3.7 / 2.2 kW (continuous) - 5.5 / 3.7 kW (30 min) Machining Capacity X-Axis travel: 420 mm Y-Axis travel: 300 mm + 60 mm Z-Axis travel: 250 mm Maximum drilling diameter: 13 mm Maximum tapping diameter: M12 Table Table size: 600 x 340 mm Table load capacity: 150 kg Feed Rates Rapid traverse X / Y / Z axes: 48,000 mm/min Working feedrates X / Y / Z in linear interpolation (max): 12,000 mm/min Manual feedrates: 0 – 1,260 mm/min Tool Changer Tool taper: BT-30 Shank: MAS-P30T-1 45° Tool magazine capacity: 10 stations Max. diameter of adjacent tools: Ø 80 mm Max. tool length: 200 mm Max. tool weight: 3 kg Other Equipment Manuals, Electrical Schematics and CE Declaration 100-liter coolant tank with pump Transformer

Condition: like new (used), Year of construction: 2010, operating hours: 76,482 h, turning length: 800 mm, turning diameter: 430 mm, spindle speed (max.): 6,000 rpm, travel distance X-axis: 455 mm, travel distance Z-axis: 800 mm, rotational speed (max.): 6,000 rpm, feed length X-axis: 455 mm, feed length Z-axis: 430 mm, workpiece weight (max.): 5 kg, total height: 8,500 mm, total length: 2,500 mm, total width: 2,495 mm, overall weight: 8,500 kg, CNC controller: Fanuc FS31IA5 (MAPPS 4) Capacity Turning length mm: 800 Max. turning diameter mm: ø: Ø430 Turn-mill spindle X-axis travel mm: 455 Z-axis travel mm: 800 B-axis degree: ±120 (0.001º) Speed spindle rpm: 12000 Drive power kW: 9/5.5 Y-axis travel mm: ±105 Tool magazine Magazine places: 76 Tool holder: Capto C5 Tool length max. mm: 250 Tool diameter max. mm: 70/130 Tool weight max kg: 5 Lower turret X-axis travel mm: 160 Z-axis travel mm: 730 Number of tool slots St .: 10 Main spindle Speed spindle rpm: 6000 Spindle bore mm: 73 Chuck type: Hollow Chuck (8") Manufacturer: KITAGAWA Counter spindle Speed spindle rpm: 6.000 Drive power spindle kW: 7.5/5.5 Chuck type: Solid Chuck (8") Manufacturer: KITAGAWA Equipment Chip conveyor Signal lamp High pressure pump Chuck foot switch (double) for main and counter spindle Coolant gun Working time hours Under power: 76482 Spindle 1: 14010 Spindle 2: 4306 Potencial nominal kVA: 48 Basic machine dimensions / weight Fsdpfx Adoy Rpq Teropk Length mm: 2500 Width mm: 2495 Height mm: 8500 Weight kg: 8500

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, travel distance X-axis: 730 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, workpiece weight (max.): 300 kg, spindle speed (max.): 12,000 rpm, The machine spindle was recently replaced. The corresponding report can be provided upon request. TECHNICAL DETAILS Travel X-axis: 730 mm Travel Y-axis: 510 mm Travel Z-axis: 510 mm Rapid traverse X-axis: 50 m/min Rapid traverse Y-axis: 50 m/min Rapid traverse Z-axis: 40 m/min Table width: 500 mm Table height: 870 mm Table length: 500 mm Table load capacity: 300 kg Rotary table diameter: 500 mm Rotational speed (max.): 1,200 rpm Spindle speed (max.): 12,000 rpm Spindle interface: HSK-A63 Workpiece height (max.): 450 mm Workpiece weight (max.): 300 kg Tool length: 300 mm Tool diameter: 125 mm Tool weight: 8,000 g Number of tool magazine slots: 180 MACHINE DETAILS Control unit: Siemens 840 D Total weight: 14,800 kg Fpsdpfxoy N N Sue Adrjk Incoming voltage: 400 V EQUIPMENT Mori Seiki tool application manual KNOLL FKA/500 band filter system + 3 filter rolls Filtermist FX5000 emulsion extraction unit Renishaw OMP60 3D probe Chip conveyor Spindle chiller Documentation + circuit diagrams

Condition: used, Year of construction: 2008, turning diameter: 275 mm, spindle bore: 80 mm, spindle speed (max.): 4,000 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 1,345 mm, total height: 2,232 mm, total length: 4,339 mm, total width: 2,232 mm, overall weight: 7,600 kg, Equipment: documentation/manual, CNC Lathe with Y-axis, driven tools an 2nd spindle CNC Control MSX-850-lll (mitsubishi 720 BM) Turning diameter 275 / 366 mm Spindle bore diameter 80 mm Spindle speed 4000 R/min Fjdpsy Nyzgofx Adrspk Spindle motor 18.5/15 Kw Movement X-axis 260 mm Movement Y-axis +50 / -50 mm Movement Z-axis 1345 mm Movement W-axis (subspindle to mainspindle) 1275 mm Min indexing C-axis main spindle 0,001 ° Number of tools on turret 12x Number of driven tools 12 x Tool Taper BMT Bar feeder LNS Quick Load Servo lll Spindle motor driven tools 6000 R/min If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: ready for operation (used), Year of construction: 2003, travel distance X-axis: 730 mm, travel distance Y-axis: 730 mm, travel distance Z-axis: 880 mm, overall weight: 13,000 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 30,000 W, number of axes: 4, General Data Machine weight 13000 kg Main Drive Number of axis 4 Spindle Speed 12000 RPM Spindle motor power 30 kW Tool taper BT 40 Fpedpfx Adsx Imt Torek Movement X-Axis Movement 730 mm Z-Axis Movement 880 mm Y-Axis Movement 730 mm This 4-axis MORI SEIKI NH-5000 40 was manufactured in 2003, featuring a robust horizontal machining centre with a spindle speed up to 20,000 rpm and a power range of 22-30 kW. It includes a versatile tool magazine with a capacity up to 180 tools and a dual-pallet automatic changer to enhance productivity. Pallet size is 500 × 500 mm, supporting a maximum workpiece height of 1,000 mm. Consider the opportunity to buy this MORI SEIKI NH-5000 40 horizontal machining centre. Contact us for more information. Application Types Milling

Condition: good (used), Year of construction: 2006, turning length: 1,000 mm, spindle speed (max.): 5,000 rpm, rotational speed (min.): 12,000 rpm, We offer you: Fjdpfx Adoxxraqsrspk Manufacturer: MORI SEIKI Model: NT 4200/1000S Year of manufacture: 2006 Control: MITSUBISHI M-720BM (MAPPS 2) Technical Data: Turning length: 1,000 mm Bar capacity: max. 65 mm Main spindle: Max. speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: Ø 73 mm Counter spindle: Max. speed: 5,000 rpm Drive power: 22/15 kW Spindle bore: Ø 73 mm Milling spindle: Speed range: 0 – 12,000 rpm Tool interface: Capto C6 Number of tool positions: 100 Hollow chuck: Ø 67 mm Operating hours: approx. 27,000 h Spindle hours: approx. 16,100 h Technical features and equipment: - Y-axis - Fully indexable B-axis - Chip conveyor, discharge to the right - Standard coolant system - Interface for high-pressure coolant system, 70 bar - Tool spindle with through-coolant - Coolant spray gun - Air blast through counter spindle - Manual tool presetting on the main spindle - 3-color signal light - Double foot switch - Simultaneous 5-axis machining - Automatic power shut-off - Tool offset for 5-axis machining - Programmable data input - Dynamic diameter/radius exchange - Stroke check before movement Operating hours: 26,875 h (as of 22.08.25) Spindle hours: 16,093 h (as of 22.08.25) Accessories, illustrated tools, and clamping devices are only included if explicitly specified in the additional information. Subject to change and error in technical details and specifications. Prior sale reserved!

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 71, turning length: 360 mm, turning diameter: 440 mm, spindle speed (max.): 5,000 rpm, bar passage: 45 mm, controller model: Fanuc 18iTA, TECHNICAL DETAILS Turning diameter: 440 mm Turning length: 360 mm Spindle speed: 50 - 5,000 rpm on both spindles Bar capacity: 45 mm Spindle nose: ASA A2-5 C-axis: 0.001 on both spindles MACHINE DETAILS Fedsy E Hpiepfx Adrspk Control: Fanuc 18iTA Upper turret: 12 driven stations Lower turret: 12 driven stations Main spindle: 11 / 7.5 kW Sub spindle: 7.5 / 5.5 kW EQUIPMENT Chip conveyor Parts catcher Bar loader interface Bar loader: LNS Mini-Sprint S2 42/3M

Condition: good (used), Year of construction: 1999, 4-axis CNC lathe with sub spindle and 2 turrets Control: Fanuc 18iTA Upper turret: 12 driven stations Lower turret: 12 driven stations C-axis: 0.001° on both spindles Main spindle: 11 / 7.5 kW Sub spindle: 7.5 / 5.5 kW Spindle speed: 50 - 5,000 rpm on both spindles Bar capacity: 45 mm Spindle nose: ASA A2-5 Turning diameter: 440 mm Turning length: 360 mm Fjdsy Enhmopfx Adrepk Chip conveyor Parts catcher Bar feeder interface Bar feeder: LNS Mini-Sprint S2 42/3M

Condition: excellent (used), Year of construction: 2013, CNC Control: M730BM X mm: 1,050 Y mm: 530 Z mm: 510 Worktable dimensions mm: 1,350 x 600 Table load capacity kg: 1,200 Distance spindle nose to table mm: - Cutting feed mm/min X,Y,Z: - Max. rapid traverse m/min X, Y, Z: 30,30,30 Spindle speed rpm: 12,000 Spindle power HP: - Taper type: BT-40 Torque Nm: - Tool changer type: - Tool changer positions: 30 Max. tool diameter mm: 80 Max. tool diameter with adjacent positions empty: 150 Max. tool length mm: 300 Max. tool weight kg: 8 Coolant tank capacity l: - Through-spindle coolant bar: - EQUIPMENT Fsdpeymxbfjfx Adrspk Chip conveyor Work light Electronic handwheel BT-40 taper

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, CNC Control: MSG-501 + MAPPS X axis mm: 800 Y axis mm: 510 Z axis mm: 510 Worktable dimensions mm: 1,100 x 600 Table load capacity kg: 1,000 Cutting feedrate mm/min (X, Y, Z): - Max. rapid traverse m/min (X, Y, Z): 42, 42, 42 Spindle speed rpm: 12,000 Spindle power kW: 18.5 Taper type: ISO-40 Torque Nm: - Tool changer type: RANDOM Tool changer positions: 30 Max. tool diameter mm: 80 Max. tool diameter with adjacent positions empty: 125 Max. tool length mm: 300 Max. tool weight kg: 8 Coolant tank capacity l: 230 Through spindle coolant bar: - EQUIPMENT Chip conveyor Oil chiller Automatic shutdown system DIMENSIONS Length mm: 2,788 Fpodpfx Adex Rvtborek Width mm: 2,710 Height mm: 2,603 Weight kg: 6,350