Used Plaster Worm for sale (368)

Condition: excellent (used), For sale: sturdy pallet truck with an unusual lattice construction. Ideal for transporting containers, crates, and loads with non-standard dimensions. - Load capacity: 2200 kg Bljdowz Sa Espfx Addor - Length: 160 cm - Width: 66 cm - Height: 29 cm, lifts up to 37 cm - Openwork design – lighter and easier to keep clean - Durable steel frame - Double front and rear wheels for increased stability - Fully functional hydraulic pump - Ergonomic handle with lifting and lowering function Technical condition: good. ///// Price shown is per unit /////

Condition: ready for operation (used), Year of construction: 2001, A complete 5-layer coextrusion blown film line with 5 extruders and all peripheral equipment is available. Total line dimensions X/Y/Z: 14m/22m/11m, blow head: Kiefel Worms FSBK 500 with IBC, die diameter: 500mm, film width range: 700mm-2000mm, haul-off width: 2000mm, winding width: 2000mm, line speed: 120m/min, melting capacity: 500kg/h, total power requirement: approx. 300kW. 1) Double winder Wintech, winding width: 2000mm, film thickness range: 35µm-150µm, max. roll diameter: 1000mm, max. roll weight: 1900kg, core inner diameter: 152mm/6inch. 2) Extruder Kiefel Worms 70.29D, power: 89kW, screw: 5-zone barrier screw, speed: 125rpm, renewed: 2010. 3) Adhesive extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 4) Center extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone core progressive screw, speed: 175rpm. 5) Adhesion promoting extruder Kiefel Worms 50.25D for the outer layer, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 6) Kiefel Worms 80.25D outer layer extruder, power: 125kW, screw: 5-zone barrier screw, speed: 150rpm. 7) Reinhold SRK 200/9.6 film calibrating device. The entire line is controlled by a Plast Control system. Further components: integrated width measurement, C-scan for profile measurement, web center control, corona pre-treatment, film pre-draw. Including a replacement FSBK 5-layer blow head with IBC, replacement rollers, annular gap blower with filter, suction units, crane and external system terminal. Documentation available. On-site inspection is possible. Bedjv T An Sspfx Addelr

Condition: new, functionality: fully functional, Year of construction: 2025, For our machines fit parts from German machines With water pump !!!! Technical data: Capacity depends on the type of pump . 6-35L / min. Max pressure max. 30 bar. Main motor - 5.5kW, - 400 rpm Basket motor : 0.55kW, - 28 rpm Diaphragm compressor 0.9kw, 250L / min Water pump Minimum water pressure 2.5 bar at machine on Capacity of hopper 145 L +/- 5 bags Height of hopper 910mm Width 720mm Height with motor 160 cm Weight with accessories 285 kg Basic equipment - rotor stator D6-3 - Plastering gun with 12mm nozzle - Pressure mortar hose 25mm, 10m with couplings - 1/2″ air hose - Water pump - Cleaner - Mixer - Spray nozzle cleaner - Hose cleaner - Toolbox with - Operating instructions APPLICATION - gypsum plasters - Gypsum-lime plasters - cement plasters - lime plasters - lime-cement plasters Bedpfx Asrvi Sksddjlr - mineral plasters - insulating plasters - Mortars for filling joints - reinforcing and adhesive mortars - liquid screeds - masonry mortars - self-levelling putties

Condition: used, Perfectly working grinding machine "станка 3Л722" Basic parameters Accuracy class A Maximum workpiece dimensions (length x width x height) 1250 x 400 x 400 Bodpfoqwzt Nsx Addolr Maximum dimensions on electromagnet 1250 x 400 x 280 Minimum dimensions on electromagnet 50 x 40 x 3 Distance from the spindle axis to the table mirror mm 210..625 Maximum product weight kg 600 Maximum weight on electromagnet 400 Machine work table Dimensions of table work surface (length x width) 1000 x 400 Table feed speed 3..35 Grinding head Dimensions of grinding wheel ПП450х80х203 Grinding wheel speed/min 1460 Maximum grinding speed m/s 34.4 Maximum diametrical feed, mm 430 Accelerated transverse disc feed m/min 1,2 Automatic cross feed for each table feed mm/rev 1..60 Maximum vertical disc feed, mm 415 ?? 0,002 ?? 0,2 Automatic vertical disc advance, mm 0,002..0,128 Vertical accelerated advance speed, m/min 0,2 Electrical equipment Number of motors 13 Disc spindle motor power, kW 11 Hydrostatic pump motor power 4 Hydrostation air heat exchanger motor power 0,09 Lubrication system pump power 0,25 If you have any further questions, we will be happy to answer them.

Condition: excellent (used), SILOMAT for silos FREE FALL type or PRESSURE TYPE. For plastering machine or other use. /dozens of pieces/ We have also for sale about 200 transportable silos (free fall or pressure type). Bsdpfx Ajlf Niqoddjlr Sales in Poland (BIESLKO BIALA lub OLSZTYN) or Italy (RIMINI). KNAUF, BAUMIT, PFT, M-TEC, MALTECH, MIXER, PUTZMEISTER, mortar, plaster, cement, silos, silo, silomat, silomats

Condition: new, Year of construction: 2025, pressing force: 200 t, table width: 1,000 mm, table length: 1,000 mm, retraction force: 70 t, Equipment: safety light barrier, COLUMN TYPE DOUBLE-ACTION PRODUCTION PLACE TURKEY WARRANTY PERIOD 24 MONTHS 200 / 70 TONS COLUMN HYDRAULIC PLASTERING PRESS FOR TECHNICAL SPECIFICATIONS TYPE 4 COLUMN BODY MATERIAL St52 – ERDEMİR COLUMN SHAFT DIAMETER Ø 90 – 4 Units. Induction chrome coated shaft SLIDE BEARING BRONZE Zr14 CAPACITY (RAM) 200 TONS CAPACITY (POT) 70 TONS DISTANCE BETWEEN COLUMNS 1000 x 1000 mm Blodpfx Asvy Db Teddsr PARALLELITY TOLERANCE 120 micron/mt. PERIPHERALITY TOLERANCE 60 micron/mt. STROKE (RAM) 800 mm STROKE (POT) 200 mm MIN. INTERMEDIATE SPACE 100 mm MAX. INTERMEDIATE SPACE 900 mm WELDING STRESS RELIEF Stress relief by vibration WELDING APPLICATION EN ISO 15614-1/2017 welding application certificate accredited by TÜRK-AK and approved by WPQR and WPS. (Welding applications are supervised by “welding coordination engineers” certified according to EN ISO 14731) MAX. WORKING PRESSURE 250 Bar TOTAL MOTOR POWER 22 kW– IE3 MAIN PUMP 36 cm³ – REXROTH or PARKER MOVABLE TABLE FAST Descent Speed 150 mm/sec. MOVING TABLE PLASTERING SPEED 12 mm/sec. MOVING TABLE RETURN SPEED 170 mm/sec. POT TABLE FORWARD SPEED 30 mm/sec. MAIN CYLINDER INNER DIAMETER Ø 320 mm – Ck45 POT CYLINDER INNER DIAMETER Ø 190 mm – Ck45 AUXILIARY ACCELERATOR CYLINDERS 2 pcs. APPROXIMATE HEIGHT OF PRESS 4000 mm APPROXIMATE WIDTH OF PRESS 1450 mm APPROXIMATE DEPTH OF PRESS 1450 mm LOWER TABLE HEIGHT FROM GROUND 1300 mm PRE-FILL VALVE NG 125 HYDRAULIC UNIT REXROTH or PARKER COOLING SYSTEM SUCTION – CIESSE – PARKER OFF-LINE FILTRATION REXROTH or PARKER MOTOR CLASS USED FOR THE UNIT IE3 LEVEL INDICATOR REXROTH or PARKER AIR FILTER REXROTH or PARKER – 10 MICRON PERMEABILITY RETURN FILTER REXROTH or PARKER – 25 MICRON PERMEABLE OIL AND HEAT INDICATOR REXROTH or PARKER VALVES USED REXROTH or PARKER FILTER CONTAMINATION WARNING ELECTRONIC CONTROL LUBRICATING STYLE AUTOMATIC – (CAN BE ADJUSTED FROM THE SCREEN) RAM STROKE SETTING CAN BE ADJUSTED FROM THE SCREEN POT STROKE SETTING CAN BE ADJUSTED FROM THE SCREEN RAM TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN POT TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN SYSTEM ERROR INFORMATION CAN BE VISIBLE ON THE SCREEN PRESS STATUS INFORMATION CAN BE VISIBLE ON THE SCREEN MOLD MEMORY CAN BE VISIBLE ON THE SCREEN ADJUSTABLE HYDRAULIC UNIT OIL TEMPERATURE INFORMATION CAN BE SEEN ON THE SCREEN LINEAR DISTANCE SCHEDULE NOVATECHNIK or TURCK PLC APPLICATION DELTA TOUCHSCREEN DELTA 7 ‘’ SWITCH MATERIALS SIEMENS – SCHNEIDER APPROXIMATE WEIGHT 14.5 TONS

Condition: excellent (used), KD-PUTZ with dimple Completely made of stainless steel Sheet metal fettling machine for perforated plates normal plates with 2 edge for 60x80 sheets on the short side edge Top condition Blsdpfxogh A Sve Addjr Connection 16 Ah

Year of construction: 2005, condition: ready for operation (used), A Stürtz CNC corner plastering machine for PVC window frames is available. Axes: 4, process: Corner plastering/gasket groove milling/inner and outer radius machining/gasket drilling, min. frame dimensions X/Y: 305mm/400mm, max. frame dimensions X/Y: 2350mm/3300mm, operating pressure: 7bar. On-site inspection is possible. Blsdpfjwwvwtex Addor

Condition: new, Year of construction: 2025, Putz P4 cement For on-site preparation of plasters CEMENT, SAND, LIME Pump motor 5.5 kw Mixer motor 2,2 kw 55/min Capacity for 2L6 pump approx. 25 l/min Capacity for 2L6 pump +++ 45 l/min Compressor 350 l/m Tank capacity 130 l Mixer capacity 130 l Height to mixer 118 cm Height to pump tank 71 cm Width of pump tank 64 cm Length without shoe 165 cm Weight 360 kg Bledpfstuiqysx Addor Included Working hose Air hose Spray gun Hose cleaning ball Shneka 2L6

Condition: good (used), Year of construction: 2022, Plastering machine concrete pump InoTec InoComb Maxi Power Set, year 2022, Ser.Nr.22612, 5,5kw drive motor 400V, delivery distance 50m, delivery height 30m, water pressure increase integrated, delivery 8-50l/min, compressor integrated, water hose, mortar hose ca.30m, fine plastering device short and long straight, good condition little used, many accessories Bedpfxokl Adye Addolr

Condition: new, Year of construction: 2025, pressing force: 60 t, table width: 700 mm, table length: 700 mm, retraction force: 20 t, Equipment: safety light barrier, COLUMN TYPE DOUBLE-ACTION PRODUCTION PLACE TURKEY WARRANTY PERIOD 24 MONTHS FOR 60/20 TONS COLUMN HYDRAULIC PLASTERING PRESS TECHNICAL SPECIFICATIONS TYPE 4 COLUMN BODY MATERIAL St52 – ERDEMİR COLUMN SHAFT DIAMETER Ø 90 – 4 Units. Induction chrome coated shaft SLIDE BEARING BRONZE Zr14 CAPACITY (RAM) 60 TONS CAPACITY (POT) 20 TONS DISTANCE BETWEEN COLUMNS 700 x 700 mm PARALLELITY TOLERANCE 120 micron/mt. PERIPHERALITY TOLERANCE 60 micron/mt. STROKE (RAM) 400 mm STROKE (POT) 100 mm MIN. INTERMEDIATE SPACE 100 mm MAX. INTERMEDIATE SPACE 500 mm WELDING STRESS RELIEF Stress relief by vibration WELDING APPLICATION EN ISO 15614-1/2017 welding application certificate accredited by TÜRK-AK and approved by WPQR and WPS. (Welding applications are supervised by “welding coordination engineers” certified according to EN ISO 14731) MAX. WORKING PRESSURE 250 Bar TOTAL MOTOR POWER 7.5 kW– IE3 MAIN PUMP 22 cm³ – REXROTH or PARKER MOVABLE TABLE FAST Descent Speed 150 mm/sec. MOVING TABLE PLASTERING SPEED 12 mm/sec. MOVING TABLE RETURN SPEED 170 mm/sec. Bljdpfjvy Dbtox Adder POT TABLE FORWARD SPEED 30 mm/sec. MAIN CYLINDER INNER DIAMETER Ø 175 mm – Ck45 POT CYLINDER INNER DIAMETER Ø 100 mm – Ck45 AUXILIARY ACCELERATOR CYLINDERS 2 pcs. APPROXIMATE HEIGHT OF PRESS 3100 mm APPROXIMATE WIDTH OF PRESS 1050 mm APPROXIMATE DEPTH OF PRESS 1050 mm LOWER TABLE HEIGHT FROM GROUND 1000 mm PRE-FILL VALVE NG 100 HYDRAULIC UNIT REXROTH or PARKER COOLING SYSTEM SUCTION – CIESSE – PARKER OFF-LINE FILTRATION REXROTH or PARKER MOTOR CLASS USED FOR THE UNIT IE3 LEVEL INDICATOR REXROTH or PARKER AIR FILTER REXROTH or PARKER – 10 MICRON PERMEABILITY RETURN FILTER REXROTH or PARKER – 25 MICRON PERMEABLE OIL AND HEAT INDICATOR REXROTH or PARKER VALVES USED REXROTH or PARKER FILTER CONTAMINATION WARNING ELECTRONIC CONTROL LUBRICATING STYLE AUTOMATIC – (CAN BE ADJUSTED FROM THE SCREEN) RAM STROKE SETTING CAN BE ADJUSTED FROM THE SCREEN POT STROKE SETTING CAN BE ADJUSTED FROM THE SCREEN RAM TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN POT TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN SYSTEM ERROR INFORMATION CAN BE VISIBLE ON THE SCREEN PRESS STATUS INFORMATION CAN BE VISIBLE ON THE SCREEN MOLD MEMORY CAN BE VISIBLE ON THE SCREEN ADJUSTABLE HYDRAULIC UNIT OIL TEMPERATURE INFORMATION CAN BE SEEN ON THE SCREEN LINEAR DISTANCE SCHEDULE NOVATECHNIK or TURCK PLC APPLICATION DELTA TOUCHSCREEN DELTA 7 ‘’ SWITCH MATERIALS SIEMENS – SCHNEIDER APPROXIMATE WEIGHT 5 TONS

Condition: new, Year of construction: 2025, functionality: fully functional, Ball Mill with Air Classifier: The Ultimate Powder Processing Equipment In the world of industrial powder production, precision, efficiency, and flexibility are paramount. Whether producing ultra-fine powders for high-tech applications or coarser materials for everyday products, the combination of a Ball Mill with Air Classifier offers unparalleled performance. This dynamic duo provides a comprehensive solution for industries ranging from chemicals and ceramics to paints, plastics, and pharmaceuticals. This article introduces the ball mill with an air classifier, explores its applications, and highlights the key advantages of this essential powder equipment. General Introduction to Ball Mill with Air Classifier ball mill with air classifier is an advanced grinding and classification system designed for efficient, high-quality powder production. The system consists of two main components: 1. Ball Mill: A cylindrical grinding device filled with grinding media (such as steel balls) that operates by rotating around its axis. The raw material is reduced to smaller particle sizes through impact and friction within the mill. 2. Air Classifier: A sophisticated device that separates particles based on size using airflow. Fine particles are carried away, while coarser particles are returned to the ball mill for further grinding. The combination of these two components creates a closed-loop system that ensures consistent particle size distribution, high efficiency, and minimal waste. Applications of Ball Mill with Air Classifier The ball mill with air classifier is a versatile solution used in a wide range of industries to process various materials. Key applications include: 1. Mineral Processing The system is widely used in the production of minerals such as calcium carbonate, quartz, feldspar, and talc. These finely ground minerals are essential for industries like ceramics, paints, plastics, and rubber. 2. Cement and Construction Materials Cement and other construction materials require precise particle size control for optimal performance. The ball mill with air classifier ensures uniformity and enhances the quality of construction materials. 3. Chemicals and Pharmaceuticals Fine powders play a critical role in the chemical and pharmaceutical industries. From active pharmaceutical ingredients (APIs) to industrial chemicals, this system delivers the consistent quality required for these applications. 4. Paints, Coatings, and Pigments The production of paints and coatings demands ultra-fine powders to achieve smooth finishes and vibrant colors. The ball mill with air classifier produces high-quality powders for superior results. #### 5. Food and Agriculture Food-grade powders such as additives, preservatives, and agricultural products like fertilizers can be efficiently processed using this system, meeting stringent regulatory requirements. Bledsvlwkxspfx Adder Industries That Benefit from Ball Mill with Air Classifier Several industries rely on the capabilities of this system to produce fine powders with specific characteristics: - Ceramics: Produces high-purity powders for tiles, insulators, and advanced ceramics. - Rubber and Plastics: Creates fillers and additives for improved durability and performance. - Pharmaceuticals: Ensures consistent particle size for APIs and excipients. -Construction: Delivers materials for concrete, plaster, and other applications.

Condition: used, Year of construction: 1997, Technical details: Blodpfxsx Aq Egj Adder max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm min. number of teeth: 6 max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg without filter *

Condition: ready for operation (used), Year of construction: 2014, cutting diameter 360 mm capacity 90 degrees: flat 500 x 350 mm capacity 45 degrees: round 360 mm capacity 45 degrees: flat 420 x 300 mm capacity 60 degrees: round 300 mm capacity 60 degrees: flat 300 x 200 mm turning speed range: 20 - 100 m/min dimensions of saw-band 4780 x 34 x 1.1 mm engine output 3.0 kW Control SPS weight 740 kg range L-W-H 2800 x 1080 x 2340 mm In good condition Current new price approx. 17.000 euros Special price on request Features: - Robust electro-hydraulic semi-automatic band sawing machine (INDUSTRY) * For sawing hollow profiles and solid materials made of steel, stainless steel, tool steel, non-ferrous metals, and plastic - with miter cuts from 60° right to 60° left * Cutting angle fixed via quick-release lever - Swiveling control panel with NC “SPS MITSUBISHI” control - Infinitely variable saw blade speed - Saw blade guide with adjustable carbide plates for precise cutting Bodpfjx A H Tyjx Addslr - With robust three-phase motor with overload protection - Saw blade drive with low-maintenance, oil-lubricated worm gear - With mechanical saw blade tensioning and monitoring - Chip removal brush for optimum cleaning and maintenance of the saw blade - Coolant device - 1x replacement saw blade - Operating instructions

Condition: good (used), Year of construction: 1995, functionality: fully functional, Control system: SIEMENS 840D Solution Line (electrical overhaul in 2017) X-travel: 7,000 mm Y-travel: 2,100 mm Z-travel: 1,500 mm Z-travel (spindle in vertical position): 1,200 mm Feed rate X, Y, and Z axes: 2–12,000 mm/min Bjdpfx Aoxz Ecqeddjlr Rapid traverse speed X, Y, and Z axes: 12,000 mm/min Universal milling head UFKSpindle speeds: 22 - 2,400 rpm Drive power 100 / 60 ED: 31.5 / 39 kW Max. torque main spindle: 2,200 Nm Swivel range of milling head (C axis): 180° Swivel range of milling head (A axis): 340° PREISELER AWU 650 automatic reversible clamping device Year of manufacture: 1995 with FORKARDT F630 vertical three-jaw chuck: 630 mm Center height above plate: 500 mm Max. workpiece weight (clamped in flight): 2,000 kg Max. workpiece weight (with counter bearing): 4,000 kg Counter bearing with hydraulic quill Tailstock quill taper: MK6 Tailstock center height: 500 mm Clamping plate Dimensions (LxWxH): 6,000 x 1,500 x 300 mm Max. load: 90 t T-slots: 6 pieces 28H7 (DIN650) T-slot spacing: 250 mm Coolant system with paper belt filter Manufacturer: ALLWEILER AG Type: PF 60 DVS / 500 Pump capacity at max. 3 bar: 40 l/min With recirculation unit Equipped with Automatic turning clamp with worm gear: PEISLER AWU650 Various roller blocks and supports6 UK500 machine clamping tablesMAYFRAN TYPE MT10 hinged belt conveyor SIEMENS SINUMERIK HT2 electronic handwheel Milling head design with hydromechanical rapid tool clamping Direct contactless measurement via linear measuring systems Oil circulation lubrication for main gearbox and milling head drive Work platform traveling in X direction, protective cover with viewing windows The machine is in exceptionally good condition and can be viewed under power. In 2017, a new SIEMENS 840D Solution Line control system was installed, and all drive motors and the control cabinet were replaced.

Condition: used, Year of construction: 2025, Band saw for metal, with optimal cutting range, commonly used in carpentry, production and craft facilities. Machine description Universal CORMAK BS 712 A band saw with CE marking is a trusted solution for metal cutting, unparalleled for years. Features high efficiency and easy handling. Makes it possible to cut in vertical plane and perpendicular to the cut material axis, or at any angle in 45°–90° range. Element cut can be fed manually or by any feeding device. The feed during cutting is gravitational on the principle of oil flow in a two-chamber hydraulic cylinder. Suitable speed of arm lowering is obtained thanks to the valve controlling oil flow between the hydraulic cylinder chambers. Blsdpfxewl Ea Ts Addor Required band linear velocity is obtained by changing the ratio on the belt pulley between the worm gear and the driving motor. Rugged, stable and refined construction as well as the arm made of uniform cast iron provide high rigidity and stability while cutting, ensuring accuracy and long-term reliability. The design of the 20 mm saw blade used in the machine makes it possible to cut large quantities of elements. Technical data Cutting band size 2360×27×0.9 mm Band tension mechanical (manual) Band speeds 22, 33, 45, 65 m/min Feed speed 0–50 m/min (stepless feed) Arm lowering control stepless – hydraulic cylinder Power supply 3-phase 400V Main motor power 1.1 kW Weight 190 kg Angle 0°.....180 mm....300×180 mm.....180×180 mm 45°.....130 mm....120×125 mm.....125×125 mm Machine construction Cutting band transmission system is composed of two cast iron wheels. The first wheel is a tensioning wheel (adjusted with a lever) and the second one is a drive wheel. Torque from the worm gear is directly transmitted to the tensioning wheel, while the worm gear is driven by an electric motor. Appropriate band angle is ensured through a set of roller bearings. The base of the machine is a rigid cuboid made of steel sheets inside which is a cooling fluid container with a flood coolant pump. Due to swivel vice it is possible to cut material at 0°–45° angles. Tank for flood coolant draining and a container for chips are fixed to the upper part of the machine. Cast iron workbench is attached to the tank, which in turn is equipped with a vice for material clamping and to which the arm of the band saw is fixed. In the lower part of the machine base are holes for wheel axles. Safety during cutting process is ensured by an electric installation meeting all CE requirements. The machine is equipped with a limiting switch that stops the machine after cutting process is finished, an emergency button, a number of microswitches that switch the machine off when, e.g., the belt transmission guard or cutting band guard are opened. Additionally, our machine, as opposed to competitors, is equipped with a wire brush for band cleaning – it prevents the blade from blocking and ensures a more effective cutting. WARNING !!!! MACHINE IS RETURNED, NO PACKAGING, DENTED MOTOR COVER ,COMPLETE, ASSEMBLED (poz. 518)

Condition: like new (used), functionality: fully functional, power: 1.5 kW (2.04 HP), For sale: AUMA SAR 07.5 electric valve actuators complete with AC 01.1 integrated controllers and VDG 63.40/50 gearboxes. These are premium multi-turn/part-turn actuators widely used in energy, biomass, district heating, wastewater, industrial automation, and power generation. Bjdpfx Adoxy Rcyjdslr Key Features 30–60 Nm torque, 32 rpm 1.5 kW motor, 400V 3-phase IP67, –25…+60 °C Local/Remote operation via AC01.1 Manual override (Handmanöver) Integrated display and safety interlocks VDG63 gear reducers included Units are in excellent working condition, from an operating energy facility, with clean housings and dry electrical connections. Actuator type Electric actuator for valves/dampers Torque range 30–60 Nm Speed 32 rpm Motor power 1.5 kW Voltage 3×400 V, 50 Hz Protection class IP67 Temperature range –25 … +60 °C Control interface Integrated AC 01.1 (Local/Remote/Off selector) Manual override Full Handmanöver with red decoupling lever Gear unit VDG 63.40/50 (AUMA worm gearbox) Gear unit rating ~ 4.7 A, mechanical reduction for high-torque valves Identification Labels: 7Gi-206, 7Gi-209, 7Gi-208 etc. Ingress protection Outdoor-capable, dust-proof, splash-proof

Condition: new, Year of construction: 2024, pressing force: 100 t, table width: 800 mm, table length: 800 mm, Equipment: safety light barrier, COUNTRY OF ORIGIN : TURKEY WARRANTY PERIOD : 24 MONTHS DELIVERY TIME : READY STOCK FOR 100/40 TONS COLUMN HYDRAULIC PLASTERING PRESS TECHNICAL SPECIFICATIONS TYPE 4 COLUMN COLUMN SHAFT DIAMETER Ø 90 mm - 4 pcs. Induction chrome plated shaft CAPACITY (RAM) 100 TONS CAPACITY (POT) 40 TONS DISTANCE BETWEEN COLUMNS 800 x 800 mm USEFUL USABLE AREA 800 x 1100 mm PARALLEL TOLERANCE 120 micron/mt. Steepness TOLERANCE 60 micron/mt. STROKE (BOOT) 600 mm STROK (POT) 200 mm MIN. spacing 100 mm MAX. SPACING 700 mm WELD TENSION REMOVAL Stress relief by vibration WELDING APPLICATION - EN ISO 15614-1/2017 welding application certificate accredited by WPQR and WPS accredited by TÜRK-AK. (Welding applications are supervised by "welding coordination engineers" certified according to EN ISO 14731) Proportional Speed Application The system is designed as a proportional speed feature. By entering different speed and stop values at different points of the pressing process, the effect of material and mold deformations on the work done is minimized. MAX. working pressure 250 Bar TOTAL MOTOR POWER 15 kW- IE3 MAIN PUMP 23 cm³ - VICKERS MOVABLE TABLE FAST DESCEND SPEED 150 mm/sec. - Proportional Adjustable MOVABLE TABLE PLOWING SPEED 15 mm/sec. - Proportional Adjustable MOVING TABLE RETURN SPEED 150 mm/sec. - Proportional Adjustable POT TABLE FORWARD SPEED 30 mm/sec. - Proportional Adjustable POT TABLE RETURN SPEED 70 mm/sec. - Proportionally Adjustable MAIN CYLINDER INNER DIAMETER Ø 220 mm - Ck45 POT CYLINDER INNER DIAMETER Ø 140 mm - Ck45. AUXILIARY ACCELERATING CYLINDERS Ck45 - 2 pcs. APPROXIMATE HEIGHT OF PRESS 3900 mm APPROXIMATE WIDTH OF PRESS 1110 mm APPROXIMATE DEPTH OF PRESS 1110 mm LOWER TABLE HEIGHT FROM THE GROUND 1100 mm HYDRAULIC UNIT VICKERS COOLING SYSTEM (with fan) CIESSE LEVEL INDICATOR DONALTSON AIR FILTER CIESSE RETURN FILTER DONALTSON OIL AND HEAT INDICATOR DONALTSON VALVES USED EATON FILTER POLLUTION WARNING ELECTRONICALLY CONTROLLED AUTOMATIC LUBRICATION - (CAN BE SET ON THE SCREEN) RAM STROKE CAN BE ADJUSTED FROM THE SCREEN POT STROKE CAN BE ADJUSTED FROM THE SCREEN RAM TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN POT TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN SYSTEM ERROR INFORMATION CAN BE SEEN ON THE SCREEN Bjdpfx Adevkvu Tedolr PRESS STATUS INFORMATION CAN BE SEEN ON THE SCREEN MOLD MEMORY CAN BE SET FROM THE SCREEN HYDRAULIC UNIT OIL TEMPERATURE INFORMATION CAN BE SEEN ON THE SCREEN LINEAR DISTANCE DIAGRAM NOVATECHNIK or TURCK PLC APPLICATION DELTA TOUCH PANEL SCREEN DELTA 7'' SWITCHGEAR SIEMENS - SCHNEIDER SAFETY PLC PILZ PNOZ MULTI BEAM BARRIERS LEUZE - 2 tk. APPROX. WEIGHT 5.5 TONS

Condition: good (used), Year of construction: 2009, functionality: fully functional, Technical details max. wheel diameter 2-45 mm gear width 250 mm max. module 1,5 mm min. module 0,5 mm Control Fanuc 18i-MB weight of the machine ca. 2,2 t dimensions of the machine ca. 2100 x 1440 x 1700 m Additional information The combined CNC gear hobbing and worm milling machine KOEPFER MZ 120 is characterized by its flexible usability and is used in the small module area. Just by swiveling the milling spindle from the horizontal to the vertical position and selecting the corresponding operating mode of the CNC control, the worm milling machine becomes a gear hobbing machine and vice versa. CNC control Fanuc 18i-MB (Dialog/ISO) CNC axes = X-axis plunge axis Z-axis longitudinal axis C-axis workpiece spindle B-axis tool spindle V-axis loader axis longitudinal A-axis swivel axis tool spindle head (included as an option) Y-axis shift axis (included as an option) With the following production programs: Worm milling Hobbing Worm hobbing Bevel gear and spur gear milling Bevel gear hobbing Milling cycles = straight, oblique, crowned toothing, radial, radial-axial, co- and counter-rotating milling, Bsdpfxoxy Nhho Addolr roughing, finishing, worm gears, straight-toothed bevel gears, face gearing (option only in the partial process) Worms [Equipment] Coolant tank 300 liters KF with LNS Turbo MS 250 Chip conveyor, built in 2021!!! Kraft and Bauer fire extinguishing system Spiral conveyor Machine documentation [Technical data] Workpieces: Workpiece diameter 2-45 mm Max. workpiece length 250 mm Tooth length 150 mm Max. module in steel= 1 mm (gear hobbing) 1.5 mm (worm milling) 0.5 mm (bevel gear hobbing) Tools: Cutter diameter= 16-32 mm (gear hobbing) 40-63 mm (worm milling) Machine: Max. setting angle of milling head= +/- 45° (gear hobbing) +/- 30° (worm milling) Shift travel= 34 mm (manual adjustment) 34 mm (CNC axis) Collet/retraction mandrel W 20 Max. speed of workpiece spindle 770 rpm. Milling spindle drive 0.55 kW Max. milling spindle speed 8000 rpm Axis drives = X-axis (plunging) / travel 80 mm via CNC Z-axis (longitudinal feed) / travel 190 mm via CNC C-axis (workpiece axis) via CNC Rapid traverse = X-axis 6000 mm/min. Z-axis 6000 mm/min. Hydraulic unit 0.37 kW

Condition: good (used), Code: 0242 Brand: MVM - ITALY Model: T 1500 - CE Standard Professional wood turning lathe with copying device for wood, plaster, composite materials and various - CE Standard Technical data: Single-phase motor 220 Volt - Kw 2,5 Copying device: the copying device is a unit mounted on the rear bench. It can reproduce weather with wooden samples or with metallic templates thanks to its modern view. It is a practical and manageable tool, it permits large time saving, in batch production or mass production, too. The feed is given by a confortable wheel rotation, the wheel is mounted on the machine fore side Distance between centres mm 1500 Height of centre mm 220 Blodjxykwkspfx Addjr Tool support Spindle revolutions 4 speeds Spindle cone n° 2 Counter centre n° 3 Overall dimensions mm 2350 x 650 x 1200 h Weight kg 325

Condition: like new (used), Year of construction: 2020, operating hours: 18,000 h, functionality: fully functional, As-new Gear Grinding Machine KLINGELNBERG VIPER 500 W All-inclusive machine equipped for internal and external gearing Equipped with a special converter from EUR kW to US standard connection (simplified global connection) Available due to restructuring at a high-tech family-run company (no automotive production) Working Area and Capacities Max. workpiece diameter: 500 mm Max. grinding stroke: 500 mm Working area over table (min.–max.): 300 – 800 mm Distance between spindle center and table (min.–max.): 442 – 1042 mm Module (generating grinding module): 0.5 – 22 Swivel angle (min.–max.): –180° to +45° Grinding System Grinding wheel diameter (min.–max.): 221 – 350 mm Grinding worm diameter (min.–max.): 221 – 350 mm Max. grinding wheel width: 75 mm Max. grinding worm width: 150 mm Grinding spindle power: 37 kW Max. grinding wheel speed: 6000 rpm Table and Feeds Table diameter: 400 mm Table bore Ø × depth: 100 × 500 mm Max. table speed: 1000 rpm Max. axial feed: 20,000 mm/min Max. radial feed: 12,000 mm/min Max. tangential feed: 20,000 mm/min Connections and Dimensions Total connected load: 60 kVA Machine dimensions (L × W × H): 4220 × 3120 × 2526 mm Filter unit dimensions (L × W): 3490 × 2250 mm Net weight approx.: 19,300 kg Machine Configuration – VIPER 500 W Base Machine and Options VIPER 500 W base machine Preparation for internal grinding arms Internal grinding unit V5 for straight or helical internal gears Measuring system for profile, lead, and pitch of external gears Measuring system for profile, lead, and pitch of internal gears V5 Touch Trigger Phasing System Power supply with ESR voltage drop compensation 100 mm table adapter Preparation for hydraulic clamping devices Hydromechanical unit for drawbar clamping systems Grinding oil filtration system with band filter 100 Fire extinguishing system Automatic work area door Cleaning system with spray gun Crane/hoist integrated into enclosure Isolation transformer Voltage stabilizer and isolation transformer Signal light/beacon tower Software Packages Gear PRO software Software for grinding of spline shafts Software for testing of spline shafts BIAS control software for gear grinding CBN grinding wheel software ADI dressing process optimization DLC lifetime monitoring for dressing tools Flexible profile correction for grinding operations Consumables Endless filter band Assembly/disassembly aid for filter band 100 Diamond dressing rollers CVD dressing roller D200 R1 for profile grinding CVD special dressing roller for generating grinding Grinding wheels Grinding wheel D350 B60 for profile grinding Grinding wheel D350 B45 for profile grinding Profiled grinding wheel D350 B150 for generating grinding Distance rings/intermediate plates 4 intermediate plates B100 22 intermediate plates B60 Blodpexx T N Tofx Adder 30 intermediate plates B45 37 intermediate plates B30 Additional Components Grinding wheel flange without intermediate plate Set of standard probes / measuring probes Additional Options Warranty extension from 12 to 24 months Closed Loop 1.0 basic version Interface for external automation

Condition: new, Year of construction: 2025, crosscut and miter saw type: ZS 200 N - 5 KW motor with machine stand, but without saw blade Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake u. Automat. Star delta motor control cutting width at 90deg: 420 mm cutting width at 45deg: swivelled: 295 mm Cutting height at 90deg: 200 mm Cutting height at 45deg tilted: 140 mm Saw can be tilted on one side up to approx. 25 degrees to acute angles and tilted flat to the left up to 30 degrees Machine stitched: approx. 250 kg Bedpji Dfidsfx Addjlr Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, pressing force: 400 t, table width: 1,200 mm, table length: 2,500 mm, retraction force: 200 t, Equipment: safety light barrier, FOR 400/200 TON H TYPE HYDRAULIC PLASTERING PRESS TECHNICAL SPECIFICATIONS TYPE STEEL CONSTRUCTION, 8 SLIDE H PRESS BODY TYPE BODY MATERIAL St52 – ERDEMİR SLIDE BEARING KESTLUB CAPACITY (RAM) 400 TON CAPACITY (POT) 200 TON MOVABLE TABLE DIMENSIONS 1200 x 1500 mm FIXED TABLE TABLE DIMENSIONS 1200 x 1500 mm LOWER EXTRACTOR TABLE DIMENSIONS 1050 x 1330 mm PARALLELITY TOLERANCE 120 micron/mt. HORIZONTAL TOLERANCE 60 micron/mt. STROKE (RAM) 1000 mm STROKE (POT) 350 mm MIN. INTERMEDIATE SPACE 200 mm MAX. INTERMEDIATE SPACE 1200 mm WELDING STRESS RELIEF Stress relief by vibration WELDING APPLICATION - EN ISO 15614-1/2017 welding application certificate accredited by TÜRK-AK and approved by WPQR and WPS. (Welding applications are supervised by "welding coordination engineers" certified according to EN ISO 14731) PROPORTIONAL SPEED and PRESSURE APPLICATION The system is designed as proportional speed and pressure feature. By entering different speed, stop and pressure values at different points of the pressing process, the effect of material and mold deformations on the work done is minimized. MAX. WORKING PRESSURE 250 Bar – Adjustable from Proportional Screen TOTAL MOTOR POWER 37 kW– IE3 MAIN PUMP 140 cm³ – REXROTH – Piston Power Regulated MOVING TABLE FAST Descent Speed 50 ~ 400 mm/sec. – Adjustable from Proportional Screen MOVING TABLE PLASTERING Speed 5 ~ 21 mm/sec. – Adjustable from Proportional Screen MOVING TABLE RETURN SPEED 50 ~ 450 mm/sec. – Adjustable from Proportional Screen POT TABLE FAST Descent Speed 10 ~ 40 mm/sec. – Adjustable from Proportional Screen POT TABLE RETURN SPEED 10 ~ 70 mm/sec. – Adjustable from Proportional Screen MAIN CYLINDER INNER DIAMETER Ø 450 / Ø 390 mm – Ck45 POT CYLINDER INNER DIAMETER Ø 320 / Ø 250 mm – Ck45 AUXILIARY ACCELERATOR CYLINDERS Ø 80 / Ø 50 mm – Ck45 APPROXIMATE HEIGHT OF PRESS 5600 mm APPROXIMATE WIDTH OF PRESS 3250 mm APPROXIMATE DEPTH OF PRESS 2200 mm LOWER TABLE HEIGHT FROM THE GROUND 1400 mm PRESS SIDE WINDOW DIMENSIONS 500 x 1300 mm PRE-FILL VALVE NG 200 – hawe HYDRAULIC UNIT REXROTH COOLING SYSTEM SUCTION – CIESSE OFF-LINE FILTRATION REXROTH ENGINE CLASS USED FOR THE UNIT IE3 LEVEL INDICATOR REXROTH AIR FILTER REXROTH – 10 MICRON PERMEABILITY RETURN FILTER REXROTH – 25 MICRON PERMEABILITY OIL AND HEAT INDICATOR REXROTH VALVES USED REXROTH FILTER CONTAMINATION WARNING ELECTRONIC CONTROLLED LUBRICATING STYLE AUTOMATIC – (ADJUSTABLE FROM THE SCREEN) RAM STROKE ADJUSTABLE FROM THE SCREEN POT STROKE ADJUSTABLE FROM THE SCREEN RAM TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN POT TONNAGE (PRESSURE) SETTING CAN BE ADJUSTED FROM THE SCREEN SYSTEM ERROR INFORMATION CAN BE VISIBLE ON THE SCREEN PRESS STATUS INFORMATION CAN BE VISIBLE ON THE SCREEN MOLD MEMORY CAN BE ADJUSTED FROM THE SCREEN HYDRAULIC UNIT OIL TEMPERATURE INFORMATION CAN BE VISIBLE ON THE SCREEN LINEAR DISTANCE SCHEDULE NOVATECHNIK or TURCK TEMPERATURE SENSOR PT100 4.20 mA. PARKER or ORDEL PLC APPLICATION DELTA TOUCH PANEL SCREEN DELTA 7 ‘’ SWITCH MATERIALS SIEMENS – SCHNEIDER RADIATION BARRIERS KEYENCE, LEUZE, PILZ or SICK – 2 tk. APPROXIMATE WEIGHT 25 TONS Bledev Dvv Repfx Addor

Condition: excellent (used), Year of construction: 2016, LAMELLA – CASE CLAMP PRESS GANNOMAT “CONCEPT 70 ECO” Complete in standard configuration including: - Sturdy, torsion-resistant steel frame, constructed with welded and bolted assemblies - UPPER lamella pressure beam with 6 elements, SIDE lamella pressure beam with 5 elements - Lamella pressure beams feature the tried-and-tested tolerance compensation system (Ganner system) for tightly pressed carcass joints - Counter-pressure surfaces (side pressure wall, bottom) are 38 mm thick, coated, continuous support plates - Continuous pressing surface with a height of 95 mm on the lower vertical pressure beam - Electromotive adjustment of both pressure beams via precision trapezoidal thread spindles (with increased pitch and concentricity accuracy) and high-performance lead nuts with grease reservoir - Clamping is electromotor-driven, with two separate worm gear motors (2 x 0.75 kW) - The pressing force of the pressure beams is continuously adjustable electronically using two potentiometers and regulated via frequency inverters, providing a completely wear-free press force control Blsdpfew Td A Ijx Addsr - Pressing force for horizontal beam: min. 500 daN (kg) up to stepless max. 2200 daN (kg) Pressing force for vertical beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Press and adjustment speeds of the pressure beams with fine positioning, switchable via 3-stage selector: 5 / 10 / 25 mm/sec - Extremely user-friendly operation - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm - Machine No. 563.624 - 400V, 3Ph, 50Hz (3.2 kVA, 16 A) Set of machine feet for 500 mm working height Operating manual in German Overhauled by Ganner, with 6-month parts warranty Location: ex stock 54634 Bitburg - Immediately available -

Condition: new, Year of construction: 2025, Cut-to-length and mitre saw type: ZS 200 N - 5 KW motor Blsdjk H Ic Uopfx Adder with machine stand, Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake and automat. Star delta motor control Cutting width at 90 degrees: 420 mm Cutting width at 45 degrees: swiveled: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees inclined: 140 mm Saw can be swiveled on one side up to approx. 25 degrees to an acute angle and tilted flat to the left up to 30 degrees Carbide circular saw blade 520x4.0/2.8 x 50 mm 60 WZ neg. for wood RLH-ST60 6.0 mtr. measuring length, mounting side: left Cross-cut fence / roller conveyor, heavy-duty design, Stop slide adjustable from the workstation via handwheel, electronic-digital dimension display, pneumatic clamping of stop slider, stop flap folds backwards, with steel rollers 60 mm diameter, roller spacing 200 mm, 400 mm roller width, with 4 support feet and connection piece: overall length: 6.7 mtr. Surcharge for digital electronic display unit type: FIAMA EP6 for 230 V mains operation, with electric on/off switch and socket. Powerful dark red LED display. Higher accuracy than the battery-powered crystal display RO-ST60 4.0 m long feed roller conveyor Mounting side: Right Heavy-duty design, steel rollers: 60 mm Diameter, roller spacing: 200 mm 400 mm roller width, 3 support feet and connection piece Location: From stock 54634 Bitburg - immediately available - Picture: similar. Machine is still in original packaging