Used Slitting Mashine for sale (302)

Condition: used, 72”x 0.5” x 60,000Lb Braner Turret Type Loop Slitting Line Braner Turret Type Loop Slitting Line is used for coil metal cross cutting with maximum width 72”, maximum 0,5” metal thcikness and 60,000Lb coil capacity Make: Braner Year New: 1996 Material Thickness: .060″ – .500″ Material Width: 12″ – 72″ Coil Weight: 60,000Lb Line Speed: 120 – 250 feet per minute Coil ID: 20″ – 24″ Coil OD: 75″ Slitting Cap: .500″ / 4 cuts – .125″ / 40 cuts Entry L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Control Panel Mandrel Uncoiler Powered Hold – Down Roll Outboard Bearing Support Hydraulic Feed-Up Drive Water Cooled Brake Hydraulic Peeling Table Driven Entry Pinch Rolls Adjustable Edge Guides Entry Mechanical Crop Shear Two Turret Type Slitting Heads Arbor Diameter: 12″ Powered Arbor Adjustment Powered Head Rotation Motor: 100HP DC Drive Lots of Knives & Tooling Two (2) Scrap Winders Powered Open / Close Heavy Duty Design Looping Pit Cross Over Table Drag Board Tension Stand Material Feeding Table Recoiler Hydraulic Drum Powered Push Off Hydraulic Over-Arm Separator Outboard Bearing Support 300HP DC Motor Drive Exit L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Upgraded Siemens Digital Drives, Electrics, Controls, Knives & Tooling Rcodpfx Asrn Sqhjireh

Condition: used, Slitting line SECO 60″ x 0.375″ x 50,000Lb (A3791) is perfect solution for longitudinal coil metal cutting into strips with maximum metal thickness 0.375” and maximum coil width 60” Cold Rolled and Hot Rolled Steel 18-60” Strip Width 2 Speed Gear Box 200-500 FPM Thickness: .032″-.375” Redpfx Aijtiy Ntoroch Complete Line with the Following Components: L-Type Entry Coil Car 40,000# Max Coil Weight Uncoiler: Coil ID: 23-30.50” Coil OD: 72” Maximum Coil Weight: 40,000# Maximum Sliding Base Hydraulic Expansion Peeler and Hold Down Roll 5 Roll Coil Breaker Entry Adjustable Edge Guides Entry Crop Shear Slitting Head: 10” Arbors 40 HP Motor Drive 2 Scrap Winders Recoiler: Coil OD: 72” Max Coil ID: 24” 150HP DC Motor 3 Arm Exit Turnstile 40,000# per Arm Motorized Turn Complete Line with Knives, Rubbers, and Spacers Controls, Hydraulics, and Electrics

Condition: used, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 625RS10HWPp-D22092022, coil weight: 10,000 kg, feed rate X-axis: 35 m/min, number of straightening rollers: 5, sheet thickness aluminum (max.): 2 mm, sheet thickness steel (max.): 2 mm, sheet thickness copper (max.): 2 mm, inner diameter: 508 mm, sheet thickness (max.): 2 mm, outer diameter: 1,250 mm, mandrel diameter: 508 mm, coil width: 1,250 mm, coil outer diameter: 1,250 mm, number of blades: 8, type of input current: three-phase, working width: 1,250 mm, total width: 4,500 mm, total length: 5,700 mm, total height: 1,600 mm, load capacity: 10,000 kg, product width (max.): 1,250 mm, space requirement width: 4,500 mm, space requirement length: 5,700 mm, space requirement height: 1,600 mm, Krasser Centurio SCS-1250 slitting line with a Stolarczyk 10-ton motorized uncoiler For sale: a complete coil-fed sheet metal cutting and slitting line, manufactured by Krasser GmbH (Austria), installed new in January 2023 and used in-house ever since by a sheet metal processing company. Well-maintained, fully operational, and available for inspection while still running at our facility. Krasser Centurio SCS-1250 – slitting/cutting line Max. sheet/coil width: 1,250 mm — min. independent sheet width: 250 mm — min. slitting width: 75 mm between knives Material thickness range: steel (400 N/mm²) 0.4–1.5 mm, stainless steel (550 N/mm²) 0.4–1.0 mm, copper and aluminum 0.5–2 mm Max. cutting speed: 35 m/min Straightening unit: 5 rollers Longitudinal cutting: 6 pairs of slitting knives installed (5 standard + 1 additional pair), max. 8 Cross-cutting: electrically driven guillotine shear Roller-shear unit for partial cross-cuts included Automatic film-application (plastic protective film) unit included Automatic labeling unit included (label printer + applicator) Krasser Optimizer cutting-optimization software included Touchscreen HMI control, multilingual (including Spanish) CE-certified safety fencing Electrical connection: 3-phase 400–488V, 11 kW, 16A Pneumatic connection: 1/2", 6 bar, filtered and dried air, 50 l/min Approx. overall footprint (line + uncoiler): 5.7 m long x 4.5 m wide x 1.6 m high Lifetime production data (as of today): 176,941 m of material processed, 60,610 cross-cuts — machine has been in steady, reliable production use Rcjdpoz D Ivvsfx Aireh Stolarczyk uncoiling set (motorized, 10 tons) Manufacturer: Spółka Stolarczyk (Poland) — Type RS10HWPp-D, year 2022 Max. coil load: 10,000 kg (10 tons) Hydraulic mandrel expansion — mandrel/coil inner diameter 508–610 mm Max. coil outer diameter: 1,250 mm — coil width: 250–1,250 mm Max. unwinding speed: 30 m/min Coil car included, with hydraulic vertical lift (306 mm) and electric horizontal travel Electrical connection: 400V, 6.5 kW Weight: 3,150 kg The line and uncoiler are sold together as a working unit. Removal/dismantling and logistics to be agreed with the buyer. For technical questions or to arrange a visit, please contact us by email — we're glad to answer any question and share further documentation, photos, or a video of the machine running.

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 603737, type of input current: three-phase, product width (max.): 1,150 mm, For sale is a heavy-duty industrial Slitting and Rewinding Machine manufactured in Germany by Frank'sche Eisenwerke AG (Frank Spezial-Maschinen) under the renowned System Hofmann & Schwabe license. This robust machine is designed for continuous, high-precision slitting and rewinding of technical packaging materials, paper rolls, pressure-sensitive tapes, and specialized plastic films. Built with German heavy engineering standards, it delivers maximum stability, high structural rigidity, and long-term operating reliability. The unit comes complete with an automated/manual core loader & feed assembly side-unit, making it a comprehensive setup for converting facilities. Key Features & Capabilities: Proven German Engineering: High structural durability ensuring low vibration during continuous production runs. Versatile Converting: Suitable for slitting self-adhesive tapes, foil substrates, paper, and flexible packaging materials. Integrated Feeding Unit: Includes a dedicated side hopper and guide channel for paper core feeding and roll handling. Operator Interface: Control panel mounted directly on the frame for convenient operational oversight. Condition & Transport: Condition: Used, mechanically intact and complete with side auxiliary table. Availability: Immediately available for inspection and disassembly/loading upon request. Redpfxs Adu Dgo Airech

Condition: used, Year of construction: 2026, Slitting line 1500 x 6, made by GUIDA Line composition: - Loading coil car - Uncoiler with sliding base and single expanding mandrel - Pressure arm - Feeding telescopic table with cutting edge and deflecting roll - Entry pinch roll - Crop shear - Tilting table - Mechanical centering device - Calming rolls - Slitting shear Rcjdpfx Asymciaeiroh - Looping pit equipment (entry and exit saddles + connecting tables) - Felt press - Deflecting rolls - Titling table - Recoiler with single expanding mandrel - Separator arm - Electric equipment - Hydraulic equipment - Safety fences protection - Several tooling and accessories - Spare parts Material to be processed: Hot rolled carbon steel Material tensile strength: 400 N/mm² Coil width max.: 1.500 mm Thickness: 1 - 8 mm Coil weight: 20 Tn Coil inside diameter entry: 500/600 601 + steel spacers for bigger diameter Coil external diameter Entry/Exit: 1.700 mm Slitting shear mandrels diam.: 220 mm Blades diameter: 355 mm Line speed: 50/25 m/min with manual speed change gear Working Direction: From left to right Power supply tension: 380/50 Hz

Condition: used, Year of construction: 2018, functionality: fully functional, number of straightening rollers: 6, conveyor belt width: 1,300 mm, sheet thickness steel (max.): 1 mm, coil width: 1,250 mm, cutting length (max.): 6,400 mm, straightening roller diameter: 70 mm, space requirement width: 3,500 mm, space requirement length: 18,275 mm, space requirement height: 4,000 mm, Single-person operation, rapid access to a wide variety of sheets, automatic sheet changeover, standard sheets remain loaded in the system; the upper sheets are less common types; secure solution with a movable access aid for loading the upper decoilers; programmable slitting line with 8 pairs of knives in station version; slitting knives are alternately arranged for distortion-free cutting; rotary knives of the AL p with 100 mm diameter to achieve minimal incision; 7.2 m long conveyor belt for discharging the strips. The system layout PDF is shown as a mirror image! Rsdpfx Aiexwc E Ijrech

Condition: new, Year of construction: 2026, functionality: fully functional, number of straightening rollers: 2, sheet thickness (max.): 1 mm, number of blades: 6, type of input current: three-phase, warranty duration: 12 months, total width: 1,700 mm, total length: 2,300 mm, total height: 1,800 mm, product width (max.): 1,250 mm, number of feed rollers: 2, SLITTING AND ROLL FORMING MACHINE YF-S Rcodpj Afgzmofx Aireh

Condition: excellent (used), Year of construction: 2020, operating hours: 97 h, functionality: fully functional, machine/vehicle number: 098 / SCS, # KRASSER Centurio 1250 – Year of Manufacture 2020 – Slitting Line with 5 Automatic Knife Pairs, Leveling Unit, and Guillotine Shear For sale is a very well-maintained KRASSER Centurio 1250 from the year 2020. The machine was taken from an operational business and is in very good, immediately operational condition. It is ideally suited for sheet metal workshops, roofing companies, facade builders, and sheet metal processing companies for the economical processing of coil material. A special advantage: the machine recently underwent a comprehensive service by the manufacturer, Krasser, as part of the take-back process. ## Technical Data * Manufacturer: KRASSER GmbH, Austria * Type: Centurio 1250 * Year of Manufacture: 2020 * Machine Number: 098 / SCS * Power: 32 kW * Connection: 3 x 400–488 V AC, N + PE, 50–60 Hz * Weight: approx. 3,600 kg ## Equipment * 5 automatic knife pairs * Integrated guillotine shear * Leveling unit * Robust industrial design * High production output * Precise slitting results The KRASSER Centurio 1250 impresses with its high manufacturing quality, reliability, and economy. The extensive equipment enables efficient and precise processing of coil material while simultaneously reducing setup times. The machine is immediately available and ready for sale. Redpezcunasfx Airjch Inspection is possible by appointment.

Condition: new, Year of construction: 2026, functionality: fully functional, number of straightening rollers: 2, sheet thickness (max.): 2 mm, number of blades: 6, type of input current: three-phase, warranty duration: 12 months, total width: 1,700 mm, total length: 2,300 mm, total height: 1,800 mm, product width (max.): 1,250 mm, number of feed rollers: 2, Hydraulic slitting and cut-to-length machine for coils with a width of 1250 mm. Model: YF-S. Rcodpfx As Afd Idjirsh

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 133/SCS, cutting speed: 35,000 mm/min, working width: 1,250 mm, feed rate X-axis: 35 m/min, product width (max.): 1,250 mm, number of straightening rollers: 7, We are offering a very well-maintained Krasser CENTURIO 1250 stand-alone slitting line, manufactured in 2023, for sale. Highlights Reinforced 7-roll leveling unit Max. coil width 1,250 mm Cutting speed up to 35 m/min Suitable for longitudinal and transverse cutting as well as leveling of strip steel Modern control system with touch operation Very well-maintained condition Ready for immediate use Technical data Manufacturer: Krasser Model: CENTURIO 1250 Type: Stand-alone slitting line Year of manufacture: 2023 Condition: Very good Max. coil width: 1,250 mm Min. coil width: 250 mm Description The Krasser CENTURIO 1250 is a powerful sheet metal cutting system for the precise processing of steel, stainless steel, aluminum, copper, and zinc sheets. The reinforced 7-roll leveling unit is particularly noteworthy, as it enables excellent leveling quality and reliable processing of a wide variety of materials. Rcsdpezvgbqsfx Airsh The system is currently still in operation and can therefore be inspected at any time by appointment while running. This offers interested parties the opportunity to directly verify the condition, performance, and functionality of the machine. The machine is expected to be available in the first quarter of 2027. The exact date may vary slightly depending on the project, but we currently anticipate a release around February 2027. Early reservation or coordination of the delivery date is possible and desirable. Contact For further information, technical details, or to arrange a viewing appointment, we look forward to receiving your message or call. Category ID: 1052 Type ID: 136 Type: Slitting line

Condition: used, The SAMO slitting line, 2001 processes material up to 1,000 mm wide and is integrated with the PROMEC packaging line, 2019. (N19). Installed electrical power is 451 kW; Area 365 sq Meters Capabilities include: Coil Inside Diameters: 400 / 500 Coil Outside Diameter: 1,500 mm Strip width: Rsdpjz Iq U Nefx Airsch Entry: 350–1,040 mm Exit: 20–1,020 mm Thickness: 0.3–3.0 mm Line Direction; Left to Right Siemens S7-400 PLC Installation includes: Coil Stand- 3 Coils Uncoiler with Snub Control Roll Motor: 26.5 Kw DC Edge Control, EMG Paper Winder Peeler Table Pinch Roll Crop Shear Vollmer Contact Thickness Gauge, Slitter Head Motor Drive: 72Kw, DC 400 Volt Edge guiding with automatic adjustment before slitting head Horizontal guide rolls before slitting head Shaft OD: 180mm Slitting Knives OD: 280mm Scrap winder Edge guiding at exit Rotating tooling turnstile on rails – 4 sided with 2 arms per side Pit with Pit Car Tension stand: Tension stand on linear rails Material table with horizontal and vertical position 4 horizontal guide rolls – pneumatically engaged 3 Roll Tension bridle roll system as material break Bridle roll motor: 138kW DC Crop shear Material table Re-coiler: Full hydraulic drum Overhead separator arm Motor: 190kW DC drive Ground level L-Shape coil car with overhead hold down arm 4 – arm coil turnstile with push-off arm (5) Above ground Coil Cars All hydraulics and Controls PROMEC Packaging line: (See below) Underground coil car in front of Turnstile Scale PROMEC PACKAGING LINE, 2019 Layout Code: N19 Automatic packaging system serving the SAMO slitting line. Installed electrical power: 65 kW. Processes strip widths from 40–200 mm and thicknesses from 0.2–3.0 mm. Siemens S7-400 PLC First table: Tilting table with mandrel for coil handling Signode Strapping Machine Overhead Manipulator- Horizontal Coil Handling with expanding mandrels into ID or 3 arm OD clamping Packages eye to the sky or eye to wall. All hydraulics and Controls

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, total width: 1,700 mm, total length: 1,100 mm, total height: 1,100 mm, input voltage: 380 V, SLITTING AND PROFILING MACHINE YF-LS Rodps Afhg Defx Airjch Six blades

Condition: good (used), Year of construction: 2019, functionality: limited functionality, machine/vehicle number: 377/2019, cutting width (max.): 1,000 mm, type of input current: three-phase, input current: 25 A, working width: 1,050 mm, input voltage: 380 V, input frequency: 50 Hz, Equipment: documentation/manual, TTR and hot foil slitter/rewinder. TTR1000 Material width: max 1050mm Max unwinding diameter: 700mm Max rewinding diameter: 150mm Max jumbo core length: 1100mm Rewinding shafts with tooling: 1 inch and 1/2 inch Redpfez R Rdrox Airech Slitting system: razor blade manual set 2 rewind turrets (upper and lower) for easy change The machine is generally in good condition. It has tension control issues on one of the shafts, likely related to the magnetic powder clutch. The machine is still installed and ready for production, so we can arrange a live demo.

Condition: like new (used), Year of construction: 2025, functionality: fully functional, FORSTNER nuSLIT longitudinal slitting and cut-to-length line, year 2025. The machine is in excellent condition and fully operational. It was used only at several exhibitions and in a demo center. The machine is designed for longitudinal slitting and sheet cutting operations. It is fully programmable, with automatic adjustment of the longitudinal slitting knives. Longitudinal slitting into 6 strips (5 pairs of knives) with the possibility to mount up to 7 pairs. Equipped with a modern F3 control system featuring a touchscreen interface, which allows easy programming of different lengths, widths, and quantities. The controller communicates with an electronic eye, automatically sets the zero point, and enables precise, clean perpendicular cuts. Integrated material-saving function – the machine stops, the slitting knives are raised, and the sheet is automatically fed into the shears. Rcedpsy Dfnnofx Airjh Comes with complete technical documentation. Specification: Model: FORSTNER nuSLIT 1250 Made in: Austria Year: 2025 Working width: 1250 mm Max. thickness: up to 1.0 mm Longitudinal slitting knives: 5 pairs Cutting: rotary shears Controller: F3 Other features: automatically adjustable longitudinal slitting knives If you have any further questions, we will be happy to assist you.

Condition: excellent (used), functionality: fully functional, coil weight: 8 kg, sheet thickness (max.): 3 mm, sheet thickness steel (max.): 3 mm, total width: 1,250 mm, Slitting line for sale Rsdpfev Twi Rex Airjch

Condition: excellent (used), Year of construction: 1995, operating hours: 50,000 h, functionality: fully functional, machine/vehicle number: 0,4-3, conveyor belt thickness: 3 mm, coil weight: 20,000 kg, conveyor belt width: 1,500 mm, sheet thickness aluminum (max.): 3 mm, sheet thickness steel (max.): 3 mm, blade shaft diameter: 160 mm, sheet thickness (max.): 3 mm, number of blades: 15, type of input current: DC, load capacity: 20,000 kg, space requirement height: 3,000 mm, feed roller diameter: 510 mm, Longitudinal slitting line for strips with a thickness from 0.4 mm to 3 mm. Decoiler 20 tons, diameter 510 mm / 610 mm, recoiler diameter 510 mm / 15 tons. The line is operational and can be tested. Operator training can be provided. Decoiler purchased in 2015, made in China. Recoiler purchased in 2021, manufacturer Poland. New electronics and new control system in 2021, manufacturer Poland. Rcsdeynuwlspfx Airoh

Condition: ready for operation (used), Year of construction: 2001, operating hours: 120 h, functionality: fully functional, machine/vehicle number: 638 TTR, film width: 1,100 mm, The Slitter Dusenberry is a slitting and rewinding machine manufactured by Dusenbery® Converting Systems. Rjdpfoz Rq Ebex Airsch

Condition: excellent (used), Year of construction: 2007, FOD BYDGOSZCZ* DPPD III 50E 530/150 multi-blade slitting saw Catalog number 7405 TECHNICAL DATA - max. cutting height 150mm - max. workpiece width 700mm - working width of the saw mandrel 530mm - max. saw blade diameter 450mm (installed 350mm) 350mm - arbor bore diameter 90mm from above: - pawls - 2 toothed draw shafts from below: Rcodpfxs Agupfo Airoh - 2 smooth draw shafts - saw mandrel - smooth draw shaft - 4 feed speed settings - feed motor approx. 2kW - 30kW motor - machine dimensions L/W/H 2400x1700x1900mm - weight approx. 3000kg – Polish production – Used machine, very good condition Net price: 38900 PLN Net price: 9050 EUR, depending on the exchange rate of 4.30 EUR (Prices may vary due to higher fluctuations) * MAR-MASZ guarantees the quality of your purchase, but is not an authorized representative of the manufacturer. All trademarks and names are used solely for informational purposes, to identify the product. We only resell products that the manufacturer has previously introduced to the market. We have no business relations with the manufacturer.

Condition: used, functionality: fully functional, Year of construction: 1976, control type: manual, degree of automation: manual, actuation type: electric, working width: 600 mm, sheet thickness (max.): 3 mm, sheet thickness aluminum (max.): 3 mm, sheet thickness copper (max.): 3 mm, sheet thickness steel (max.): 3 mm, sheet thickness stainless steel (max.): 3 mm, power: 22 kW (29.91 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 5 bar, pressure (min.): 4 bar, pressure (max.): 5.5 bar, overall weight: 4,500 kg, total length: 3,000 mm, total width: 2,200 mm, total height: 1,800 mm, Equipment: centralized greasing system, MINO GIOVANI BATTISTA Circular Shears for Cutting Steel Sheets 600 mm x 3 mm – used Coil Slitting Line – MINO GIOVANI BATTISTA + Strip Straightener MINO GIOVANI BATTISTA Max. sheet thickness: 3 mm Max. cutting width: 600 mm Knife sets (more than 50 pieces) Inner coil diameter: 400–550 mm Outer diameter: up to 1,500 mm Max. coil weight: up to 5 tons Decoiler and recoiler with spacers Technical Data Drive type: electric Working width: 600 mm Max. sheet thickness: 3 mm Max. steel thickness: 3 mm Power: 22 kW (29.91 HP) Connection voltage: 380 V Frequency: 50 Hz Total weight: 4,500 kg Total length: 3,000 mm Total width: 2,000 mm Total height: 1,800 mm Equipment • Centralized lubrication system • Pneumatic coil removal from decoiler • The machine is powered and currently installed in production Included Free of Charge Along with the circular shears, we provide a sheet metal cold rolling machine free of charge for achieving tight thickness tolerances. MINO GIOVANI BATTISTA – Rolling Machine Model: LAS Power: 6 kW Weight: 4,500 kg Cold rolling machine (for tight tolerances) Max. material width: 130 mm Max. material thickness: 3 mm Decoiler, belt-driven power transmission Prices Circular shears: EUR 11,000 Rolling machine: EUR 3,500 The rolling machine is included in the package at no extra charge, as it was used together with the line. Disassembly and loading costs: EUR 1,800 Delivery Terms Parity: EXW 10290 Zaprešić – Croatia Loading space length: 6 m Width: 2.2 m Total weight approx.: 9 tons Prices are net of VAT – reverse charge Delivery Time The machine is available 10–15 days after payment. The fixed loading date must be announced at least 7 days in advance for organizing forklift and crane. Rsdpfxeyn Shzs Airoch

Year of construction: 1972, condition: good (used), strip width: max. 830 mm Rcedegrykhopfx Aireh strip thickness: 0,3 - 4 mm blade shaft Ø: 140 mm No. of slits/material thickness: 25/0,5 mm 4/4 mm

Condition: excellent (used), Cut to length - Slitter Rcsdpfx Ajzyyt Ieireh input width 1250mm thickness; 0.35-2.2mm input coil : 6.5ton, output 6.5 ton.

Condition: used, 1. Decoiler Brand : SCHLOEMANN Type : Hydraulic expanding decoiler Function : Coil holding and controlled rotation Expansion control : Hydraulic Frame : Welded steel base with integrated brake Estimated capacity : 8–12 tons Coil bore : Ø 508 mm ----- 🔹 2. Straightener / Pinch Roll Manufacturer : COMEC (Société de Constructions Mécaniques de Creil) Type : Pinch roll and leveler Control : Mechanical Order number : 1305.1268 Recommended lubricants : Shell Macoma, Tellus, Alvania (as per nameplate) Function : Feeds and flattens strip before slitting Secondary role : Synchronized strip puller ----- 🔹 3. Slitter Manufacturer : COMEC Type : Circular blade slitting machine Drive : Mechanical gear train Blade adjustment : Manual Rcjdpfx Aijw Dd Igersh Blades installed : ~10 sets (visible) Function : Longitudinal slitting of metal sheets into narrow strips ----- 🔹 4. Shear (End Cropper) Manufacturer : COMEC STAMCO Type : Rotating or inline shear Function : End cropping or final length cut Control panel : Electromechanical (visible on photo) Machine Application Complete line for metal coil slitting, producing narrow strips from master coils, with upstream flattening and final end cutting. Features / Differences – Heavy-duty hydraulic decoiler by SCHLOEMANN – Mechanical straightening section from COMEC – Manual-adjust slitter with circular blades – Outfeed shear for end trimming or final cut-to-length – Older but industrial-grade line, suited for medium gauge materials

Condition: used, CARBONINI SIZER 1500 RNTPC – Year 2008 General Information Rsds Ad I D Hjpfx Airoch Manufacturer: CARBONINI S.r.l. – Italy Model: SIZER 1500 RNTPC Year of manufacture: 2008 (as indicated on the CE identification plate) Weight: 5,500 kg (as indicated on the identification plate) CNC Control System: MicroVision Machine Type: Automatic coil-fed sheet metal cut-to-length line, 1,500 × 1.2 mm, suitable for sheet thicknesses from 0.6 to 1.2 mm. Machine Description The CARBONINI SIZER 1500 RNTPC is an automatic coil-fed sheet metal cut-to-length line designed to process metal coils through unwinding, straightening, automatic feeding and transverse cutting to the required length. It is particularly suitable for the production of sheet metal components used in air conditioning, ventilation and air handling systems (HVAC industry). The line produces sheet metal blanks cut to programmable lengths, with electronic control of dimensions and production quantities through the MicroVision CNC control system. The system consists of several processing units that perform the different production stages directly from the metal coil. Line Configuration The cut-to-length line consists of the following operating units: 1. Gantry-Type Coil Decoiler Designed to support and unwind sheet metal coils, continuously feeding the material into the subsequent processing units. 2. Sheet Metal Straightening Unit Equipped with a series of rollers designed to correct bends and deformations caused by coil winding, ensuring material flatness before cutting. 3. Double Rectangular Notching Unit Allows rectangular notching operations on the sheet metal, depending on the installed configuration. 4. Transverse Shearing Unit Automatically cuts the sheet metal to the length programmed by the operator, producing blanks with preset dimensions. Technical Specifications Maximum working width: 1,500 mm Minimum sheet thickness: 0.6 mm (6/10) Maximum sheet thickness: 1.2 mm (12/10) Control system: MicroVision CNC Overall Dimensions and Weight Overall length: 7,000 mm Overall width: 2,400 mm Weight: 5,500 kg CE marking: Present

Condition: used, Year of construction: 1971, operating hours: 1,23,45,678 h, functionality: fully functional, machine/vehicle number: M4514, Slitting shear with adjustable table for rubber sheets. Rcodpfsz Rm R Tex Airjh The desired cutting size can be variably adjusted, and the table feed is automatic. The shear operates smoothly.

Year of construction: 2003, condition: excellent (used), functionality: fully functional, strip width: max. 1.500 mm strip thickness: 0,5 - 2 mm Rcodpjrazyqsfx Airsh coil weight: max. 7 t mandrel Ø: 508 mm