Used Swing Chisel for sale (2,774)

Condition: used, operating hours: 29 h, Description: BOBCAT E27 Z 29 short-tail excavator, demonstration model, quick coupler 29, operating hours like new, TOP condition!! * First commissioning in 2026 * Standard equipment * TOPS/ROPS cabin with heater * 1,500 mm dozer blade * 300 mm rubber tracks * Long dipperstick * Heavy counterweight * Hydraulic bolt-on quick coupler LA with E27z2 cabin, with AUX5 * Automatic idle * LED work lights on the front and rear of the cabin * Floating function for the dozer blade * Adjustable double-acting auxiliary hydraulics with quick couplings * Battery disconnect switch * Pre-installation for hydraulic clamp * Control console lock * Hydraulic monitoring with shut-off * Foldable and ergonomic pedals * Warning tone when the fuel tank is full * Grease gun holder * Horn * Proportional auxiliary and swing hydraulics control via push button * Automatic safety belt * Suspension seat with high backrest * Two travel ranges with automatic transmission * Four mounting points on the upper carriage Technical specifications: Bledpfxj Agw Nvo Albep * Diesel engine D1105-E4B-BCZ-1 (Kubota) * 15.3 kW at 2,400 rpm * Cooling: Water * Hydraulics: Total flow rate: 86.8 l/min * System relief pressure for auxiliary hydraulic circuits: 180 bar * Auxiliary hydraulic flow: 50.0 l/min * Digging depth with long dipperstick: 2,847 mm * Max. speed, low range: 2.5 km/h * Max. speed, high range: 4.3 km/h * Operating weight: approx. 2,700 kg (cabin + heater) * Quick coupler M503 with lifting hook * Swivel bucket, hydraulic, 1,200 mm * 2 years Bobcat manufacturer's warranty or 2,000 operating hours. Despite the greatest care, errors within the advertisement cannot be ruled out. We reserve the right to make changes and sell the item in the meantime!

Condition: used, empty load weight: 4,860 kg, maximum load weight: 13,140 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 10/2014, loading space length: 4,900 mm, loading space width: 2,350 mm, loading space height: 900 mm, loading space volume: 10 m³, suspension: air, tire size: 385/65R22.5, color: blue, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: en route / in transit, steel body, 2 axles, tandem, air suspension, ABS (anti-lock braking system), roll-over cover, rear support Body: Tandem 3-sided tipper with roll-over cover, approx. 10 m³ capacity, galvanized frame, swing-out side gates. All information is subject to change without notice, as the vehicle is currently en route! ACCESSORY INFORMATION IS WITHOUT GUARANTEE, subject to changes, prior sale, and errors! Bjdpfx Ao Agw T Solbelp

Condition: used, maximum load weight: 29,720 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 10/2026, next inspection (TÜV): 10/2027, Bottom loading and top loading for gasoline, diesel, heating oil, etc. Saddle plate height 1200mm unloaded. Metering system: as per GMV with additional venting, meter DN 100 / 1,000 l/min, manufacturer Sening, with full-hose valve. 1 measured outlet. Emptying hose, cylindrical shape, separate parallel tank, material: light metal, 0.5 bar test pressure. 5, 5.0 mm minimum wall thickness, head 5 mm, bottom 7.5 mm. 5 Chamber 1 with sloped bottom plate, discharge slope towards the rear (wedge). 5 3 chambers, approx. 38,500 l gross, distribution from front: 13,300 / 6,000 / 19,200 liters gross. 5 Total filling volume approx. 36,200 l net, max. filling volumes: 12,500 / 5,500 / 18,200 liters (= max. filling volumes for bottom loading according to VOC. The actual usable filling volume also depends on the permissible axle loads and the permissible total weight!). 5 Baffle plates as required. 5 Discharge slope controlled by actuating the air suspension during discharge. Lifting loops at the front and rear of the tank to upright the partially loaded tank semi-trailer. 5 Conductors (deflectors) in the chambers to dissipate static charge. 5 Supports (small tables) as bottom valve protection and for holding the filling pipe during top loading, mounted in each chamber. Walkway / ladder / folding railing: as per safety walkway on the right. 5 1 folding railing within the dome fairing, right. 5 Intermediate platforms in front of the dome covers. 5 1 access ladder at the rear right. Dome fittings: 5 per chamber: • 1 manhole cover NW 500 (EN 13317) with filling opening DN 265, recessed installation. • 1 pneumatic tilt valve with sequential control. • 1 vent pot with flame arrester. • 1 overfill protection, electric VOC version (EN 13922). Bottom fittings: « Per chamber 1 pneumatic bottom valve DN 100 (EN 13316). « 1-channel collector. Bottom loading: 5 Bottom loading cabinet on the left. • Swing flap, lockable (square lock). • Drainage channel and drainage device (front). 5 per chamber: • 1 filling coupling. • 1 electric overfill protection system (VOC) 10-pole VOC socket, acting on the land side. Unloading device: « Right side in the fitting cabinet: • Bus flap, lockable (square lock). • Drainage channel and drainage device (front). 38,500 l capacity, 3 chambers (13,300/6,000/19,200), wall thickness 5mm, tank code LGBF for low-viscosity mineral oils class 3. 1 metering system, pump 1x full-hose, discharge on the right side of the vehicle, hydraulics: 8 Hydraulic pump drive. Hydraulic hoses. Coupling plugs (supply / leak oil / return). Pneumatics: for supplying the braking system, air suspension and the tank fittings: Air tank made of aluminum. Test connections combined. Accessories: 2 fire extinguishers 6 kg in a plastic box. 2 wheel chocks. 1 changeover warning board at the rear. 3 flame symbols, foldable. 3 hazard labels “environmentally hazardous substances” (Fisch & Baum), foldable. Rear view camera, manufacturer Motec, in the upper lighting bar. Pneumatically actuated flap at the rear of the trailer. Supply of the imaging components for the tractor unit (without installation). 1 container cabinet made of light metal, rear right. Acoustic reversing buzzer at the vehicle rear. Inclination indicator (level), right. 2 grounding lugs per vehicle side. 1 aluminum hammer, right. 1 shaft hook, right. 2 pole boards, right. 2 absorbent containers with holder. Pylons with holder. Shovel and broom. Drip trays under the outlets. Shaft cover. Bljdpfx As Agduzjlbjp

Condition: used, Year of construction: 1990, Equipment: ABS, all wheel drive, SPIERINGS Lattice Boom Tower Crane / Truck Crane Truck: ? Engine power: 222 kW / 305 hp / Displacement: 8,250 cm³ Bodpfx Alj Ahp Rbebolp ? Vehicle dimensions: 12,395 x 2,600 x 4,000 mm ? Operating weight: 35,000 kg ? GVW: 36,000 kg including 7,080 kg ballast weight ? Tires: 445/65 R22.5 ? 3 axles ? 1st and 3rd axles steered ? All-round warning lights Crane: ? Max. outreach: 30.4 m ? Max. lifting capacity: 5,000 kg at 9.3 m outreach ? Drive type: hydraulic, hydraulic pumps electrically driven by external power or generator ? Control type: electrically actuated proportional and control valves ? Max. corner load: 204 kN ? V/max: 85 km/h ? Can only be moved by the undercarriage! Hoisting winch: ? Motor: hydraulic variable motor ? Drive group: 1Am ? Displacement: 20..55 cm³ ? Max. feed pressure: 260 bar ? Gearbox: planetary gearbox, i=27 ? Drum diameter: 375 mm ? Max. rope pull force: 25 kN ? Corresponding rope speed: 30 m/min ? Holding brake: spring-loaded disc brake Trolley: ? Motor: hydraulic constant motor ? Drive group: 1Am ? Displacement: 16 cm³ ? Max. feed pressure: 265 bar ? Gearbox: planetary gearbox, i=10.4 ? Drum diameter: 200 mm ? Max. rope pull force: 6 kN ? Max. speed: 50 m/min ? With limit switch ? Holding brake: spring-loaded disc brake Slewing unit: ? Motor: hydraulic constant motor ? Displacement: 16 cm³ ? Max. feed pressure: 300 bar ? Gearbox: planetary gearbox, i=160 ? Max. slewing speed of the upper carriage: 1.3 rpm ? Swing brake: hydraulic brake valve ? Holding brake: spring-loaded disc brake Boom luffing winch: ? Drive group: 1Em ? Motor: hydraulic constant motor ? Displacement: 16 cm³ ? Max. feed pressure: 220 bar ? Gearbox: planetary gearbox, i=92 ? Drum diameter: 200 mm ? Max. rope pull force: 38 kN ? Max. speed: 18 m/min ? Holding brake: spring-loaded disc brake ? With limit switch Load / Load moment limiter: ? Pressure switch on the hoisting winch motor ? Mechanical switch actuated by bending of the tower slewing frame Tower: ? Working height: 20.8 m ? Outer tower: length 9.9 m, inner tower: 11 m Boom: ? Jib boom in lattice structure, optionally horizontal or at a 30° incline ? 1st boom section: length 11 m / 2nd boom section: 11.1 m / 3rd boom section 7.8 m - German machine! - Ready for operation! Errors and prior sale excepted!

Condition: excellent (used), Year of construction: 2009, These very good, used universal lathes come from a training center and are being sold due to restructuring. There are 3 identical lathes available. Center height: 180 mm Distance between centers: 1000 mm Swinging diameter over bed: 360 mm Swinging diameter over cross slide: 250 mm Bed width: 190 mm Spindle bore: 42 mm Bedpfx Asziuybjlbelp Spindle mounting according to DIN 55027: Size 5 Speed range, 16 steps: 33 – 2000 rpm Feeds, 13 longitudinal: 0.03 – 0.4 mm/rev Likewise, 13 cross: 0.01 – 0.13 mm/rev 27 metric threads: 0.2 – 7 mm 36 Whitworth threads: 4 – 72 threads/inch 18 module threads: 0.3 – 3.5 module 21 diametral pitch threads: 8 – 44 pitch Tailstock mounting: MK 3 Drive power: 2.25 / 3.75 kW Machine dimensions L x W x H: 2000 x 1000 x 1550 mm Weight: 1100 kg Accessories / Special features: • 3-axis digital display RSF • 3-jaw chuck, diameter 200 mm • Quick-change tool holder system “Multifix”, size B • Chuck guard, foldable, electrically secured • Large chip guard • Coolant system • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 0748, film width: 400 mm, compressed air connection: 6 bar, number of blades: 1, input voltage: 230 V, year of last overhaul: 2025, Equipment: documentation/manual, We are offering this used Ravizza Packaging SRL SIMPLICITA BAG SMART 400H pouch-making machine, manufactured in 2021. Manufacturer: Ravizza Packaging SRL Model: SIMPLICITA BAG SMART 400H Year of manufacture: 2021 Condition: used Category ID: 536 Type ID: 1939 Machine type: pouch-making machine Bljdpfe Ad Ivpsx Albop For sale is a high-quality packaging system from the manufacturer Ravizza Packaging SRL (Italy). Additionally equipped with: EIDOS Swing Mk II thermal transfer printer integrated conveyor belt film feed existing film rolls as shown in the photos Condition: The system is in good condition and was used in production until recently. Normal signs of wear and tear corresponding to its age and area of application are present. An inspection and demonstration of the machine's functionality are highly recommended and can be arranged by appointment. Collection: The machine is located in Germany, 63589 Linsengericht, and is available for inspection and collection. Loading can be supported upon agreement.

Condition: new, Year of construction: 2026, * Now available: Plate compactors for attachment – Top features. We are pleased to offer you these plate compactors for attachment. * Condition: New machine * Availability: Immediately from stock. Why Zirndorfer-Maschinenpark? * Official dealer for Bobcat & Montabert * Family-owned business with over 45 years of experience * In-house workshop for guaranteed quality * Wide selection of new and used machines Financing, leasing, or hire purchase? No problem – we will find the right solution for you through our partner banks. Would you like to trade in your used machine? We will gladly take your machine in payment at a fair price. Attachments and accessories? We will gladly offer additional attachments and matching accessories upon request. Sale to EU or non-EU countries? We will handle the process for you. – Special features of the machine Bledpj Ahd D Ssfx Albsp 70 kN per plate * free-swinging * the price is only for the attachment, not for the compact loader – Standard features of the machine CE certification – Trust in the experience of a third-generation family business. Zirndorfer-Maschinenpark e.?K. – Your partner for construction machinery. Contact us now and secure your individual offer. – Legal note: The information provided on the internet is a non-binding description. It does not constitute guaranteed characteristics. The seller is not liable for errors, input errors, or data transmission errors. Subject to change.

Condition: used, Year of construction: 2001, spindle diameter: 40 mm, total width: 2,000 mm, total height: 1,900 mm, total length: 3,800 mm, overall weight: 3,500 kg, input voltage: 400 V, number of spindles: 5, input frequency: 50 Hz, No. 04556 Four-sided planer WEINIG Unimat 23 E Used, year of construction 2001 Spindles (bottom - right - left - top - bottom) All spindles Ø 40 mm, spindle motors with mechanical brake 1. Bottom spindle (surfacing spindle): 5.5 kW, with rebating device 2. Right spindle (jointing spindle): 7.5 kW 3. Left spindle: shared drive with right spindle (7.5 kW) 4. Top spindle: 5.5 kW 5. Bottom spindle: 11 kW Spindle speed 6000 rpm Working range Workpiece width with tool diameter 140 mm: 20 - 230 mm With aluminium planing heads, a working width of 260 mm is possible Workpiece height with tool diameter 163 mm: 8 - 120 mm Infeed table with jointing fence, length 2,000 mm Control and adjustment Bedo Afb Eajpfx Albslp ATS positioning control with Siemens SIMATIC OP7 operator panel Left spindle: automatic positioning forward - backward Top spindle: automatic positioning up - down Motorised height adjustment of the feed, 1.1 kW adjustment motor with brake Mechanical digital readouts on the spindle adjustments Feed Feed motor 3 kW with brake Feed speed 6 - 36 m/min, infinitely variable via handwheel Serrated feed rollers, driven by cardan shafts Short workpiece package for processing short pieces Top pressure rollers, swing-away Axial adjustment of the feed rollers relative to the left spindle Pneumatic pressure system with pressure reducing unit, 3 pressure regulators with gauges on the control desk Pressure shoes and tables Pressure shoe before top spindle, swing-away Pressure shoe after top spindle with wooden insert Table plate with wooden insert at bottom spindle 5 Anti-kickback device on the infeed table Manual Waxilit pump for removing resin from the table Central lubrication points on the front of the machine Safety and noise protection Full soundproof enclosure with viewing window and interior lighting CE marking, BG-tested (wood dust tested) Chip extraction connection diameters 140 mm and 200 mm Power supply 400 V / 50 Hz Scope of delivery 5 planing heads, mounted on the spindles Various spare parts: feed rollers, spacer rings, drive belts, table inserts, operator tools Complete technical documentation Transport dimensions approx. 3800 x 2000 x 1900 mm LWH Weight approx. 3500 kg To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer’s brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Payment terms: Prices plus VAT, payment before collection or shipment Delivery terms: ex warehouse

Condition: new, power: 132 kW (179.47 HP), fuel type: diesel, color: white, gearing type: automatic, number of seats: 18, Year of construction: 2026, Equipment: ABS, air conditioning, electronic stability program (ESP), soot filter, Opel Movano touring coach/school bus (identical to Fiat Ducato) / Touring coach available for immediate delivery / Order vehicle Various equipment lines COC for 16 + 1 seats Conversion as follows: - Acoustic and thermal insulation from the passenger compartment - Tinted windows (grey/black) in the original opening - 16 reclining seats plus co-driver single seat + driver's seat = 18 total, also available with a double co-driver seat for a total of 19 - (Of course, the vehicle can also be configured with 16 seats for a driver's license D1) - Optionally, a co-driver seat or a small table can be installed next to the driver's seat. - Convector heater in the passenger compartment - Air conditioning in the passenger compartment, optionally with a second compressor - Multi-level night lighting (white/orange) - Roof hatch - Electric drive for the original sliding door - Electric step at the original sliding door - On request, an electric exterior swing door is also possible - Reinforced rear axle Optional: On request, you can choose between Fiat Ducato, Citroen Jumper, Peugeot Boxer, or Opel Movano. Various equipment lines are in stock. - Electric center door + EUR 2,000.00 - Double-width center door + EUR 3,000.00 (loss of 1 seat) - 5 standing spaces - Automatic transmission - 180 hp Base vehicle with air conditioning, manual transmission, parking distance control with rear-view camera, radio with hands-free system, multi-function steering wheel, ... Wheelbase 4035 mm Overall length 6223 mm Height 2522 mm Width 2050 mm Permissible total weight 4500 kg !! Bsdpfx Ae Afcalelbolp Special equipment: Airbag driver/passenger side, Cool & Sound package, Electrical interface for additional conversions, Driver assistance system: ParkPilot system with rear-view camera, Light package 1, Tire repair kit, Seats in the driver's cab: Adjustable co-driver single seat, Seats in the driver's cab: Heated driver's seat Additional equipment: Exterior mirrors, single tires on 2nd axle/rear axle, Driver assistance system: Side wind assist, Generator 185 A, Rear wing doors with tinted glass (opening angle 180 degrees), High roof H2, Permissible total weight 4.25 t, Body/superstructure: Box-type high-roof, Body variant: Vehicle length L4, Body variant: High roof (H2), Fuel tank: 80 liters, Steering column (steering wheel) adjustable, Headlight range adjustment, Model refinement, Engine 2.3 liters - 103 kW CDTI, Pollen filter, Long wheelbase, Low emissions according to exhaust standard Euro 6e-TEMP, Sliding door loading/passenger compartment right, Side marker lights, Visibility package, Steel rims 6.5x16, Daytime running lights LED, Permissible total weight 4.25 t, Speed limitation 90 km/h Net export possible All information without guarantee These are German vehicles / no re-imports. On request, you can also order a Citroen/Peugeot/Fiat Ducato or Opel Movano. We make shipments worldwide.

Condition: good (used), Year of construction: 1998, - Heidenhain CNC Pilot control system - Accessories included - Powered tooling - Counter spindle Work area Max. turning diameter 160 mm Swinging diameter over bed 440 mm Swinging diameter over compound slide 210 mm Turning length 350 mm Main spindle Spindle bore 56 mm Bledpfs Afhifjx Albsp Max. spindle speed 5,000 rpm Drive power 7.5 kW Number of spindles: Main spindle C-axis Travel distances X-axis 160 mm Z-axis 350 mm Tailstock travel 350 mm Tailstock Arbor diameter 80 mm Tailstock travel 350 mm Tailstock mounting MK 3 Feeds Rapid traverse X 20 m/min Rapid traverse Z 30 m/min Space requirement approx. 2,800 x 1,800 x 1,800 mm Machine weight approx. 3,400 kg

Condition: used, mileage: 3,83,450 km, power: 335 kW (455.47 HP), first registration: 05/2018, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: black, gearing type: automatic, emission class: euro6, loading space volume: 44 m³, loading space length: 7,730 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, Year of construction: 2018, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, ANTOS 2546 L Beverage Truck, 7.70 m with BÄR 2.000 kg Tailgate Lift * Body: EWERS SWING WALL - Canopy * Hydraulically steered 3rd trailing axle * ONLY IN COMBINATION WITH TRAILER, Vehicle No. 4452, total net price: € 57,650.-- + * Vehicle No. for customer inquiries: 4449 * Engine version Euro VI, with OBD-C Bodpsxx D S Sofx Albelp * Trailing axle, 7.5 t, steered, can be relieved * Predictive Powertrain Control * Secondary water retarder * Active Brake Assist * Differential lock, rear axle * Air conditioning * Bunk, lower * Lane Keeping Assist * Environmental badge (green) * Driver Attention Assist * High Performance Engine Brake * Air suspension, rear axle * Air deflector, lockable * Wheel formula 6x2 ENA * Maintained according to service schedule * Stability Control Assist (ESP) * Front axle with air suspension * Hot water auxiliary heater, cab * Trailer brake connection at the rear, Duo-Matic + Standard * Trailer brake, 2-line, brake connections on the left * Trailer socket 24 V, 15-pole * Antos * Electronic brake system with ABS and ASR * Driver's air suspension seat, comfort * Transmission G 211-12/14.93-1.0 * Mercedes PowerShift 3 * Tire pressure monitoring system * Locking system, with central locking * Exterior sun visor, transparent * Digital tachograph, EG, speed * Tank 390 l, left, 650 x 565 x 1250 mm, aluminum * Cruise control * Storage compartment, low, on engine tunnel * AdBlue tank 60 l, left * Hill start assist, speed limitation 30 km/h * Roof hatch/vent flap, roof * Heater, electronic compressed air supply unit * M-cab ClassicSpace, 2.30 m, tunnel 320 mm * Engine OM470, R6, 10.7 l, 335 kW (455 hp), 2200 Nm * Wheelbase 4600 mm * Tires tubeless, 315/70 R 22.5 rear axle * Tires tubeless, 315/70 R 22.5 front axle/front lift axle/rear lift axle * Reversing warning signal * Preparation for toll collection * Additional stabilizer, rear/trailing axle * ClassicSpace * Aluminum rims 9.00 x 22.5, Speedline * Weight variant 26.0 t (8.0/11.5/7.1) * Preparation for low fifth wheel coupling system No liability for printing and typing errors Sales only to commercial customers Errors and prior sales excepted * Changes, prior sales and errors are expressly reserved. The description serves to identify the vehicle and does not constitute a guarantee in the legal sense. The description in the purchase contract shall be decisive. * TOP SERVICE + QUALITY * We would be happy to provide you with a LEASING/FINANCING/RENT-TO-OWN offer * Warranty insurance possible upon request from the insurer * TÜV / UVV LBW / Tachograph inspection and installation of OBU device by our local partners * Customs license plate for 30 days * All customs documents for export are possible, but must be requested individually * TOLL for Toll-Collect can be booked in-house * Free transfer from Stuttgart Airport or Metzingen (Württ) train station * TRAIN STATION FOR ARRIVAL: 72555 METZINGEN/WÜRTT. * FOR ENGLISH * Andreas Pittas * Thomas Pittas * Alexander Pittas * Robin Pittas WHATSAPP number * * ---- Visit us on our website at * constantly over 200 vehicles in stock

Condition: used, power: 419 kW (569.68 HP), axle configuration: 6x6, color: green, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, loading space length: 67,500 mm, Equipment: ABS, EBS, air conditioning, - Brake system Iveco X-Way AS300X57 Z/P HR ON+ Short Timber Truck, axle configuration 6X4 (with hydraulically driven front axle 6x6), tandem medium drive axle (HR), disc brakes, cab version Active Space, large driver's cab, rear air suspension, 12-speed automated HiTroniX transmission, engine 570 C13 Cursor 13 570 HP Euro VI, wheelbase 4,800 mm, AS cab with high roof, roof insulation for cab, electrically operated lifting roof transparent for MLL high roof, air suspension for cab, fog lights, front halogen headlights, electrically adjustable and heated mirrors, hybrid bumper, front underrun protection, static passenger seat, one-piece lower bed, double thermo insulated box, digital tachograph 4.0, electronic immobilizer and 2nd vehicle key, luxury driver's seat air-sprung, heated, 4-way adjustable, lumbar and headrest with integrated 3-point seat belt, 2 reinforced anti-roll bars on rear axle, designed for moderate climates, exhaust outlet to the left, 170 Ah batteries, horizontal batteries on frame, rear suspension without spacers, generator 2,160 watts (24 volts x 90 amps), 2-cylinder air compressor 630 cc, rear shock absorbers, trailer socket for 24-volt operation, 15-pin, rear axle ratio: 4.23, heated fuel prefilter with separator, adaptive cruise control (ACC), ECO-Switch to switch between Power and Eco mode to optimize Total Cost of Ownership (TCO) by fuel-optimized engine and transmission settings, driving style analysis (DSE), transmission software eco-roll freewheeling function, VDI interface (Vehicle-Data-Interface) for telematics services (FMS) version 3.0, preparation for toll system (OBU), preparation for telematics system (telematics box), hill start assist (Hill Holder), electronic stability program (ESP), lane departure warning system (LDWS), emergency braking assistant, HI-TRACTION, rocking mode (free swing mode), left and right luggage compartments, 15m tire inflation hose, headlamp protection grilles, fully automatic air conditioning, leather multifunction steering wheel, sun roller blind, auxiliary heater diesel/water 4KW, front axle 8,000 kg / 1st rear axle 10,500 kg / 2nd rear axle 10,500 kg, spare wheel, reinforced front anti-roll bar, reinforced parabolic spring on front axle, AdBlue tank 80 liters, 50 mm 190 kN Ringfeder trailer coupling, fuel tank 550 liters, CAN bus interface CAN-OPEN for body control, infotainment system incl. navigation, axle load indicator, holding effect of parking brake on front axle, LED tail lights, retarder/intarder for ZF transmission, side marker lights, tires 385/65 R22.5 - 315/80 R22.5, bumper painted in cab color, aluminum air tanks, horn behind bumper, transparent sun visor. Bsdjyfu Rmopfx Albolp SCHEMEL–SHORT TIMBER BODY Crane: Palfinger-EPSILON loading crane Y_CRANE_ON_2 M 12 Z91 - Fully hydraulic timber loading crane Manufacturer: EBERT Dimensions: approx. 6,750 mm between bulkhead and crane - 4 ExTe bolsters D5 – adjustable with clamp fastener and lashing ratchets or support for load securing - with 8 ExTe stakes D5 – telescopic - with special Z-profile subframe 200 mm high, closed with checker plate in the center of the frame - Bulkhead welded construction with internal special aluminum profiles approx. 2,600 mm high - 4 x ¼ mudguards...

Condition: excellent (used), functionality: fully functional, CNC Heavy-Duty Lathe POREBA TPK-90N × 2000 mm – SIEMENS CNC We offer a heavy-duty CNC lathe POREBA TPK-90N with a turning length of 2000 mm, equipped with a SIEMENS CNC control. The chuck visible on the photos is not included in the quipment. The machine is designed for precise machining of large and heavy workpieces. Its robust construction and massive machine bed, characteristic of POREBA heavy-duty lathes, provide high rigidity during machining. Main technical specifications: Manufacturer: POREBA Model: TPK-90N CNC control: SIEMENS Turning length / distance between centers: 2000 mm Swing over bed: approx. 930 mm Swing over carriage: approx. 630 mm Swing in gap: approx. 1200 mm Spindle bore: approx. 95 mm Max. spindle speed: up to 800 rpm Main motor power: approx. 22 kW Tailstock taper: Morse 6 Main features: SIEMENS CNC control, heavy and highly rigid machine construction, large swing over bed of approx. 930 mm, 2000 mm turning length, suitable for machining large and heavy workpieces, proven design of POREBA heavy-duty industrial lathes. The machine is located in Bydgoszcz, Poland. Inspection and test run are possible by prior arrangement. METALEX – machine tools since 1979. Bedpfez Atg Tox Albelp

Condition: used, mileage: 3,83,450 km, power: 335 kW (455.47 HP), first registration: 05/2018, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: black, gearing type: automatic, emission class: euro6, loading space volume: 44 m³, loading space length: 7,730 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, Year of construction: 2018, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, ANTOS 2546 L Beverage Truck, 7.70 m with BÄR 2.000 kg Tailgate Lift * Body: EWERS SWING WALL - Canopy * Hydraulically steered 3rd trailing axle * ONLY IN COMBINATION WITH TRAILER, Vehicle No. 4452, total net price: € 57,650.-- + * Vehicle No. for customer inquiries: 4449 * Engine version Euro VI, with OBD-C * Trailing axle, 7.5 t, steered, can be relieved * Predictive Powertrain Control * Secondary water retarder * Active Brake Assist * Differential lock, rear axle * Air conditioning * Bunk, lower * Lane Keeping Assist * Environmental badge (green) * Driver Attention Assist * High Performance Engine Brake * Air suspension, rear axle * Air deflector, lockable * Wheel formula 6x2 ENA * Maintained according to service schedule * Stability Control Assist (ESP) * Front axle with air suspension * Hot water auxiliary heater, cab * Trailer brake connection at the rear, Duo-Matic + Standard * Trailer brake, 2-line, brake connections on the left * Trailer socket 24 V, 15-pole Blodpfx Ajxx D S Ejlbep * Antos * Electronic brake system with ABS and ASR * Driver's air suspension seat, comfort * Transmission G 211-12/14.93-1.0 * Mercedes PowerShift 3 * Tire pressure monitoring system * Locking system, with central locking * Exterior sun visor, transparent * Digital tachograph, EG, speed * Tank 390 l, left, 650 x 565 x 1250 mm, aluminum * Cruise control * Storage compartment, low, on engine tunnel * AdBlue tank 60 l, left * Hill start assist, speed limitation 30 km/h * Roof hatch/vent flap, roof * Heater, electronic compressed air supply unit * M-cab ClassicSpace, 2.30 m, tunnel 320 mm * Engine OM470, R6, 10.7 l, 335 kW (455 hp), 2200 Nm * Wheelbase 4600 mm * Tires tubeless, 315/70 R 22.5 rear axle * Tires tubeless, 315/70 R 22.5 front axle/front lift axle/rear lift axle * Reversing warning signal * Preparation for toll collection * Additional stabilizer, rear/trailing axle * ClassicSpace * Aluminum rims 9.00 x 22.5, Speedline * Weight variant 26.0 t (8.0/11.5/7.1) * Preparation for low fifth wheel coupling system No liability for printing and typing errors Sales only to commercial customers Errors and prior sales excepted * Changes, prior sales and errors are expressly reserved. The description serves to identify the vehicle and does not constitute a guarantee in the legal sense. The description in the purchase contract shall be decisive. * TOP SERVICE + QUALITY * We would be happy to provide you with a LEASING/FINANCING/RENT-TO-OWN offer * Warranty insurance possible upon request from the insurer * TÜV / UVV LBW / Tachograph inspection and installation of OBU device by our local partners * Customs license plate for 30 days * All customs documents for export are possible, but must be requested individually * TOLL for Toll-Collect can be booked in-house * Free transfer from Stuttgart Airport or Metzingen (Württ) train station * TRAIN STATION FOR ARRIVAL: 72555 METZINGEN/WÜRTT. * FOR ENGLISH * Andreas Pittas * Thomas Pittas * Alexander Pittas * Robin Pittas WHATSAPP number * * ---- Visit us on our website at * constantly over 200 vehicles in stock

Condition: used, mileage: 43,487 km, power: 382 kW (519.37 HP), first registration: 08/2023, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, next inspection (TÜV): 09/2027, gearing type: automatic, emission class: euro6, Equipment: ABS, air conditioning, electronic stability program (ESP), Trailer tipping hydraulics, driver's comfort seat with air suspension and lumbar support, shoulder adjustment and heating, construction site package, EBS, full brake assist, immobilizer, MAN TipMatic Manoeuvre - maneuvering mode, LED lighting, ASR, emergency brake assist, lane departure warning, trailer coupling Ringfeder type RF50 A, MAN Mediasystem Advanced 7'', without navigation map, RIO BOX, smartphone integration, tipping body 4,900mm x 2,380mm Meiller type D316, lashing eyes retractable in the floor plate, side wall height 900mm, front wall height 1,100mm, 350mm guide plate on front wall, steps on front wall, fixed corner stanchions, rear wall height 900mm, swinging rear wall, 150mm discharge chute on tipping body, axial pump tipping hydraulics Meiller type 275/1 PTO gearbox-dependent, Dosing device for rear wall tipping bridge, hydraulic connection at the rear Blodpfx Aoucizljlbop

Condition: used, mileage: 5,14,800 km, power: 235 kW (319.51 HP), first registration: 06/2016, fuel type: diesel, axle configuration: 2 axles, color: red, gearing type: mechanical, emission class: euro6, Year of construction: 2016, CHASSIS: ZCFA71MN002652478 TITLE: IVECO EUROCARGO 160E32 WITH NEW HOOKLIFT, FRONT AND REAR LEAF SPRINGS, WITH DOUBLE TORPRESS SYSTEM REF: 24C29 YEAR: 06/2016 HORSEPOWER: 320 ENGINE CAPACITY: 6728 EURO STANDARD: 6 MILEAGE: 514800 TRANSMISSION: 9-speed manual DIFFERENTIAL LOCK: yes RETARDER/INTARDER: no AXLES: 2 WHEELBASE: 3330 TRAILER TOWING: yes ORIGIN: imported CAB: short and low SEATS: 3 PAYLOAD: 9,650 kg - TRUCK: 16,000 kg GVW - TRUCK + TRAILER: 32,000 kg GVW BODY TYPE: New hooklift HOOKLIFT MODEL: MEC T8/10.38 EXTENSION: yes SWING: no ROLLER: vertical ADR: no BODYWORK CAPACITY FROM: 3.30 m + 0.20 m TO: 4.40 m + 0.20 m TOTAL LENGTH: 6.25 m TOTAL LENGTH WITH CONTAINER: 6.65 m ACCESSORIES: - Air conditioning - Piping for crane and/or trailer - New automatic bell REFURBISHED: yes INSPECTED: yes TYRES: 50% PRICE: €72,500.00 + VAT Listed prices do not include VAT. Please contact the sales department for updated price and condition information. Blodpfxsv Aqc Ae Albsp For further information: Loris: 3484773001 URL: #glispecialistidelloscarrabile SCARRABILI AURORA operates in the sale and purchase of industrial and commercial vehicles, specializing primarily in the waste sector. Specialists in trucks, trailers, and hooklift equipment. With an immediate stock of over 50 trucks and more than 150 containers, hooklift bins with and without cranes. Errors and omissions excepted (E&OE) Given the volume of listings and details, Aurora invites verification of data accuracy with sales staff.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, For sale: this lathe. Swing diameter over bed: 1,000 mm. Turning length: 4,000 mm. Sinumerik 840D control. Bjdpfx Ajxzr Rbslbslp

Condition: excellent (used), Year of construction: 1977, functionality: fully functional, We are selling this lathe, already dismantled and stored in the warehouse. Fully functional; a video of the machine can be sent via WhatsApp. Swing over bed: 1080 mm Swing over support: 720 mm Distance between centers: 9000 mm Minimum turning diameter: 20 mm Spindle speed: 1.8 – 355 rpm Main drive power: 40 kW Workpiece weight: 10 t Bledpey I Ifwofx Albep

Condition: used, total length: 3,350 mm, total width: 1,550 mm, total height: 1,800 mm, Year of manufacture: 1999 Colour: White Empty weight: 3.300 kg In very good condition. In 2017 Refurbished for €32.000 - Year: 1999 - Documentation available: Yes - CE marking present: Yes - Drive system: Teach-in - Control system brand: Monforts - Control system type: Monforts Control System MTC K - Power [kW]: 15.0 - Centre height [mm]: 250 - Swing over bed [mm]: 500 - Carriage turning diameter [mm]: 290 - Distance between centres [mm]: 1500 - Spindle bore [mm]: 70 - Min. spindle speed [rpm]: 2 - Max. spindle speed [rpm]: 2800 - Options: Three-jaw chuck, Fixed steady - Transport dimensions: 3350mm x 1550mm x 1800mm (l x w x h) - Transport weight [kg]: 3300kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT Bjdpfx Aoztxl Nolbslp VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: good (used), Year of construction: 1990, functionality: fully functional, turning length: 2,000 mm, turning diameter: 1,000 mm, spindle bore: 104 mm, overall weight: 11,000 kg, CNC Lathe: SCNC 1000 DC x 2000 Year of manufacture: 1990 Control system: Fanuc O-TF Maximum swing over bed: Ø 1000 mm Distance between centers: 2000 mm Spindle bore: Ø 104 mm Machine weight: 11000 kg. Bsdpfs Agcwaox Albjlp Loading into a container or onto a truck is possible.

Condition: ready for operation (used), Year of construction: 2022, spindle speed (max.): 5,000 rpm, spindle motor power: 15,000 W, number of axes: 2, Horizontal turning machine manufactured in 2022. This Okuma GENOS L2000-e features a maximum turning diameter of 220 mm and a turning length of 500 mm. It is equipped with a spindle power of 15 kW and a spindle speed of 5,000 rpm. If you are looking to get high-quality turning capabilities, consider the Okuma GENOS L2000-e machine we have for sale. Contact us for further details. • Spindle: ASA6 mount, 52 mm bar capacity • Chuck: 8" self-centering • Max turning diameter: 220 mm Blsdj Adp U Hjpfx Albsp • Swing diameter: 450 mm • Max turning length: 500 mm • Tailstock: Automatic cycle with MT5 rotating center, 5 kN thrust • Software/features: Tool life management; automatic chuck open/close and tailstock advance/retraction during rotation; CNC cutting force monitoring (OSP P300LA-e TEX Kit for X/Z and spindle); IGF Advanced (L) with 3D real simulation; API Library 2 (ON STATUS) • Thermal deformation control: TAS-C (Thermo Active Stabilizer - Construction) • Usage/condition: Very little used (about 8 months of operation) Additional equipment • Chip conveyor: hinge type • High-pressure coolant pump: 0.8 kW, 5 bar, 20 l/min • Parts unloader: parts catcher arm and unloading (applicable with manual preset) • Bar feeder interface: prepared for bar feeder • Tool setter: manual presetting • Tool holder kit: 4 external, 1 front, 3 boring bar holders, 8 bushings, 3 plugs Technical Specification Counter Spindle Yes Driven Tools No

Condition: used, total width: 1,700 mm, total length: 3,800 mm, total height: 2,000 mm, Colour: Green Empty weight: 6.000 kg CNC Internal grinder, converted from a CNC lathe Bodew A I Uhopfx Albslp - Documentation available: Yes - Serial number: UC-1871 - Drive system: CNC - Control system brand: Fanuc - Control system type: 0-T - Power [kW]: 15.0 - Centre height [mm]: 115 - Swing over bed [mm]: 380 - Distance between centres [mm]: 635 - Spindle bore [mm]: 75 - Max. spindle speed [rpm]: 3500 - Options: Removable bed - Swing over removable bed [mm]: 520 - Transport dimensions: 3800mm x 1700mm x 2000mm (l x w x h) - Transport weight [kg]: 6000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: good (used), lifting height: 14,200 mm, fuel type: diesel, General information Year of manufacture: 2016 Weights Empty weight: 3.290 kg Functional Lifting capacity: 300 kg Working height: 1.620 cm Dimensions of cargo space: 609 x 218 x 282 cm CE mark: yes Condition Technical condition: good Visual appearance: good Other information TÜV Marked: yes Delivery terms: EXW Max. horizontal reach: 1120 m Max swing of platform in degrees: 400 Additional information Please contact Christian Theißen for more information Manufacturer: Multitel Model: MT162EX Year of build: 2016 Condition: Used Data: Max. working height: 16,17 m Max. platform height: 14,17 m Bjdoyvpx Ispfx Albolp Max. reach: 11,18 m Drive type: Diesel Total dimensions LxWxH: 6,09 x 2,18 x 2,82 m Platform dimension WxD: 1,40 x 0,71 m Max. basket load: 300 kg Swivel range: 400° (from the upper carriage) Ground clearance: 0,15 m Support width both sides: 3,40 m Support width one side: 2,88 m Support width: narrow 2.22 m Support length: 2,89 m Empty weight: 3.290 kg Total permissible weight: 3.500 kg Special features: Rotatable work basket, 2x 90°, supports, height limit up to 14 meters switchable. Information: Tüv and UVV new Location: 41468 Neuss: immediately available

Year of construction: 1982, condition: used, Offered for sale is a conventional center lathe with lead screw and feed rod. Distance between centers: 3000mm. Swing over bed: 710mm. Center height: 342mm. Spindle speed range: 8-1250rpm. Number of spindle speed steps: 23. Longitudinal feed: 0.056-10mm/rev. Cross feed: 0.028-5mm/rev. Metric thread pitches: 1-176mm. Max. workpiece weight between centers: 2500kg. Max. workpiece weight between centers with steady rest: 3000kg. Tailstock quill travel: 300mm. Equipped with digital readout, three-jaw chuck, four-way tool post and tailstock. Weight: approx. 5400kg. Overall dimensions X/Y/Z: approx. 5325mm/1510mm/1510mm. Inspection possible by arrangement. Bledo Ad Nq Ijpfx Albsp

Year of construction: 2020, condition: ready for operation (used), Offered is an extensive machinery package for textile processing, automatic cutting, laser cutting, industrial sewing, die cutting and riveting. 1) CO₂ laser cutting and engraving machine Trotec Rayjet 50 with associated extraction system, working area: approx. 457mm/305mm, laser power: 30W, max. processing speed: approx. 1.5m/s, Aigner/Trotec Atmos Cube extraction system, year of manufacture: 2020, airflow rate: 320m³/h. 2) Single-needle lockstitch flatbed sewing machine with triple feed and large vertical-axis hook Dürkopp Adler 867 ECO, subclass 867-190020-M, max. stitch length: approx. 9mm, clearance: approx. 335mm, clearance height: approx. 125mm. 3) Single-needle high-speed lockstitch sewing machine Juki DDL-9000B-SS, year of manufacture: 2019, max. sewing speed: approx. 5000stitches/min, max. stitch length: approx. 5mm, needle bar stroke: approx. 30.7mm. 4) Single-needle high-speed lockstitch sewing machine Dürkopp Adler 261-140342-02, max. stitch length: approx. 5mm, control unit: AHE59. 5) Post-bed sewing machine Pfaff 591-900/81-BL. 6) 2 identical swing-arm cutting presses Moneus 1333. 7) Manually operated riveting and setting machine with mechanical foot actuation. Documentation available. Inspection possible by arrangement. Bledpfjzt Skxjx Albop