Used Thermal Spray Coating for sale (5,702)

Year of construction: 2023, condition: like new (used), functionality: fully functional, machine/vehicle number: 018-2310-0001, Sono TEK ultrasonic spray coating system with conveyor belt or workpiece carriage - 6-head spray system Rjdpfx Aoyl Rr Hoiroch - Was set up for anti-fingerprint / hydrophobic spray coating for display glass, but has seen little use as product launch was postponed - Conveyor approx. 2 m - Flexible gantry design, allowing spray width to be easily and precisely adjusted - Siemens Simatic touch panel - Commissioning / installation support can be provided - Documentation available System is dismantled and ready for transport.

Year of construction: 2025, condition: new, A conformal coating machine is an industrial device used in electronics manufacturing to automatically apply a protective conformal coating to printed circuit boards (PCBs). This coating shields sensitive electronics from external influences such as moisture, dust, chemicals, corrosion, and temperature fluctuations. The machine applies a thin, uniform protective layer to selected areas of the PCB. This process is fully automated and reproducible, which is essential for quality and reliability in serial production. Transport System Transports PCBs through the machine (inline or stand-alone). Coating Application Depending on the configuration: - Spray coating (selective or full coverage) - Jet coating - Film or mist application techniques XYZ Positioning and Motion System Provides precise control of the spray valve. Vision and Camera System (optional) For alignment, inspection, and process monitoring. Masking / Selective Coating Protects connectors, test points, and other areas not to be coated. Rsdpfxjydnlho Airsch Drying or Curing Module For UV, thermal, or air curing, depending on the coating material. Control Software Programmable for various PCB designs and coating recipes. Suitable Coatings - Acrylic - Polyurethane - Silicone - Epoxy - UV-curable coatings Applications ICT conformal coating machines are widely used in: - Automotive electronics - Industrial control systems - Medical equipment - Aerospace - Consumer electronics Advantages - Consistent and high coating quality - Reduced material waste - High repeatability - Suitable for mass production - Improved reliability and lifespan of electronics

Condition: used, Year of construction: 2008, CEFLA FINISHING EASY 2000 DUO D Automatic Spray Coating Machine - Manufacturer: Cefla - Model: EASY-DUO D - Year of manufacture: 2008 - Working width: 1,300 mm - Operator side: left - Price: machine has not been overhauled (Overhaul available upon request) - Duo-style spray gun drive - Dry extraction - Exhaust air capacity: 12,000 m³/h - Belt conveyor system - Feed speed: continuously adjustable ~ 2–8 m/min - Belt cleaning via roller cleaning system - With paint recovery - Paint circuits installed: 2 - Number of spray guns installed: 4 Rcedpfx Aij Agvcceroh (Up to 8 spray guns can be installed as an option) - Height-adjustable spray guns - Number of paint pumps: 0 - Supply air filter panel - Explosion-proof design - Suitable for solvent-based paints - Suitable for water-based paints - Used machine, in good condition - Length: 4,867 mm - Width: 3,708 mm - Height: 2,780 mm - Total power consumption: 18 kW - Location: in stock - Voltage fluctuations: max. +/- 5% _____ Optionally, we can also provide you with a quote for the installation and commissioning of the system, as well as employee training . Upon request, we also offer regular maintenance and servicing of the machine. For more information, please feel free to contact us!

Condition: used, all stainless steel dimensions: ± 5.000 x 2.200 x 2.700 mm Rcodpfx Aoz Ry Ncoiroh drum diameter: 1.300 mm net drum length 4.200 mm adjustable inclination angle easy to clean inlet height: ± 1.700 mm (adjustable if necessary) discharge height: ± 1.000 mm power 3kW 400V, 50Hz 4 spray pipes Provided for extraction

Condition: used, Airless spraying unit WIWA, type WIWA 10.000 Paint spraying unit Year of manufacture approx. 1980 Flow rate approx. 10 L/min Operating pressure approx. 250 bar Air inlet approx. 6.5 bar - Paint spraying gun WIWA No. 2, type WIWA 500D - Approx. 14.5 m high-pressure hose with paint spraying gun - Compressed air unit with pressure regulator and oiler Rcjdpfx Aszinzljireh - Mobile base frame, pump unit with foldable suction pipe Space requirement L x W x H 700 x 700 x 1000 mm Weight 45 kg Good condition

Condition: new, Year of construction: 2025, type of input current: three-phase, overall weight: 450 kg, total height: 2,500 mm, total width: 4,200 mm, Equipment: lighting, The BUMEX SP. Z O.O. company presents a powder coating booth. Working Dimension: 4 000 x 2 200 mm 5 x filter Automatic filter cleaning with an adjustable range from 10-1200 sec. Fan 2 x 2,2 kW, 9.500 m³/h=19.000m³/h 2 x LED lamp Delivery time 14-21 days Our cabins are characterized by a very high quality of workmanship, safety of use and the selection of cab parameters to the existing building. We advise on the selection of spray booths, dedusting systems, exhaust systems and industrial recuperation. CHOOSE BUMEX SP. Z O.O. Very high quality of the machines offered on the market. Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our clients. All products of the brand BUMEX SP. Z O.O. have WE certificate. We offer our own transport - prices are agreed each time for a given offer. Rjdpfx Aijhfwy Hsrsch We issue VAT invoices. E.g. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please do not hesitate to contact us.

Condition: good (used), functionality: fully functional, Complete Industrial Powder Coating Line for Sale We offer a complete industrial powder coating line in good working condition. The installation has been professionally maintained and is suitable for coating a wide range of steel and metal products. Rsdpjzqur Hjfx Airoch Equipment includes: Pretreatment system Drying oven Powder coating booth Powder spray equipment Curing oven Conveyor system Electrical control system The complete line is available for immediate sale and can be inspected by appointment. Condition: Well maintained Fully operational before dismantling Suitable for industrial production GEMA OptiStar CG07 Powder Coating Gun

Condition: new, Year of construction: 2024, functionality: fully functional, ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Excellent Support! ✈️ Price includes shipping within Germany – No additional transport costs! ✈️ Fast delivery: Only 6 weeks after receipt of payment! PROFESSIONAL POWDER COATING HAS NEVER BEEN THIS EASY! Looking to expand your business and enter the world of professional powder coating? The PEF2.5+ is the perfect solution for beginners! This high-performance system allows efficient, cost-effective, and high-quality coating of car rims and smaller workpieces – with minimal effort! ✨UNBEATABLE PROMOTION – ONLY UNTIL THE END OF MAY!✨ Take advantage of this limited-time offer before it's too late! Rjdpfx Ajwfhu Heiroch PONY Luxury Coating – QUALITY THAT CONVINCES! ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✅ 100% European manufacturing – No China products, only top quality built to European standards! ✅ Modular & expandable – Additional options for greater performance and flexibility! ✅ All spare parts included – Long-term use with no hidden extra costs! ✳️Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today. ✳️ ✨✨Buy directly from the manufacturer and secure price and quality advantages!✨✨ ☘️Environmentally friendly☘️⚡️Green Energy⚡️☘️ Powder oven + powder booth + powder gun Complete Starter Package PEF2.5+ ⭐ Powder oven with electric heating ✔️ INTERNAL WIDTH: 1,505mm ✔️ HEIGHT: 1,800mm (from air duct) ✔️ INTERNAL LENGTH: 2,500mm ✔️ Thermoblock unit dimensions: 785x1800x2210mm; heating capacity is 30 kW/h; recirculation fan is 1.5kW/h – 1 pc.; exhaust fan is 0.54kW/h. ✔️ Double-wing door with thermal insulation and silicone seal. ✔️ Guide rails for rack trolleys are manufactured according to the dimensions specified on the base plates. ✔️ Specially designed air duct for homogeneous air distribution inside the curing oven. ✔️ Electrical panel materials by Siemens and Schneider. This curing oven does not include a PLC system. PLC is available as an option. ✔️ Curing temperature, curing time, and heater unit function are adjustable. At the end of the program, an alarm and light signal from the buzzer will indicate completion. ✔️ Additionally, a product transport trolley with cast wheels is located inside the oven. ⭐ Powder coating booth ✔️ Dimensions: 800x1930x2200mm (including fan) ✔️ Teflon filters: 4 pcs. ➢ Filter suction fan: 4kW x 1 pc. (6,000m3/h – 200mmSS) ✔️ 36W LED lighting x 1 pc. ✔️ Bottom drawer x 1 pc. ✔️ Control panel for air intake and powder spray regulation ✔️ DELTA frequency converter ✔️ Heavy-duty rollers under the coating booth ✔️ Additional filter at the fan outlet ⭐ Powder coating gun E-Coat+3 Master with Multicolor (vibration table) Enquire now – Get your business ready for the future! ☀️ 2-YEAR WARRANTY ☀️ ☀️All our machines are CE-certified and necessary machines have ATEX certificates.☀️

Condition: new, Year of construction: 2026, BUMEX Sp. z o.o. | Industrial Powder Coating Technology A professional, compact industrial powder coating system designed for serial production and demanding workshop applications. Engineered with a strong focus on process stability, structural durability and premium coating quality. A complete solution ready for immediate operation in professional powder coating facilities. Scope of Supply ✅ Powder Coating Curing Oven 1200 × 1500 × 1800 mm ✅ Powder Coating Spray Booth with Filtration System 1400 × 800 × 1400 mm POWDER COATING OVEN — BUMEX INDUSTRIAL STANDARD Technical Data Working dimensions: 1200 × 1500 × 1800 mm Total power: 18 kW Key Construction Features ✔ stainless steel front frame preventing paint peeling at the door-to-frame contact area — long-term durability and premium appearance, ✔ excellent temperature uniformity thanks to an efficient air circulation system ensuring stable curing without overheating or cold zones, ✔ heavy-duty industrial construction designed for continuous operation, ✔ 4 patented BUMEX safety locking systems guaranteeing perfect door pressure, chamber tightness and maximum operator safety, ✔ internal loading trolley and external trolley for ergonomic handling, ✔ optimised airflow circulation ensuring repeatable curing quality. Result: fast heating, stable temperature control and perfectly cured powder coating finish. POWDER COATING SPRAY BOOTH Technical Data Working dimensions: 1400 × 800 × 1400 mm Fan power: 1.5 kW Airflow capacity: 6500 m³/h Premium Equipment ✔ construction made from powder-coated galvanised steel panels providing high corrosion resistance, ✔ 2 × 100% polyester filters mounted in TWIST system — fast installation and removal without tools, ✔ automatic filter cleaning system maintaining constant performance, ✔ highly efficient and low-noise industrial extraction fan, ✔ stable airflow ensuring effective powder capture, ✔ ergonomic working area for operator comfort. Rsdjhd Nraopfx Airech BUMEX Standard ✔ CE conformity, ✔ full technical documentation, ✔ manufacturer warranty, ✔ warranty and after-sales service, ✔ professional technological consulting. Commercial Terms ✔ own transport — individually quoted, ✔ VAT invoice provided, ✔ customised configurations and dimensions available. BUMEX Sp. z o.o. We design industrial equipment built for long-term reliability, safety and predictable performance.

Condition: new, Year of construction: 2026, warranty duration: 12 months, total width: 2,300 mm, total length: 1,300 mm, total height: 2,450 mm, type of input current: three-phase, Powder paint booth, suction wall TQ2020 Working dimensions (mm): 2000 (width) x 2000 (height) x 400 (depth) Overall dimensions (mm): 2300 (width) x 2450 (height) x 1300 depth SPECIFICATION: • Fan power 2.2 kW, • Efficiency 10,500 m³/h, • 3 x 100% polyester filter Rodpfx Ajd S N Szsirjch • Filtration degree at the level of 99.9%, • Control panel IP 66, • Automatic filter cleaning • Hermetic lighting IP 65. • Paint tank Booth available immediately (Stock status) CHOOSE BUMEX SP. Z O.O. Very high quality machines among those offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our customers. All BUMEX SP. Z O.O. brand products are EC certified. We offer our own transport - prices are set each time, for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please contact us.

Condition: new, Year of construction: 2025, conveyor belt length: 3,000 mm, Powder coating set Powder Coating Oven 1500 x 3000 x 1800 mm Powder Coating Booth 2800 x 2200 mm Wagner Paint Applicator Oven/Dryer Technical Specifications: Working dimensions: 1500 x 3000 x 1800 mm with NIKO 24.000 overhead rails • Power consumption: 43 kW • Maximum operating temperature: 220°C Equipment: • NIKO 24.000 overhead rail transport • Convection (Even temperature throughout the oven) • 2 x fans for air circulation Rodeguku Uepfx Airech • Safety locks for opening and closing. Powder booth: •Working dimensions: 2800 x 2200 mm •Fan power: 2.2 kW •Fan capacity: 10,500 m³/h •Very quiet operation •Automatic filter cleaning •LED lighting Wagner Sprint 2 electrostatic applicator CHOOSE BUMEX SP. Z O.O. Very high quality machines among those offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Full technical documentation. 100% customer satisfaction. All BUMEX SP. Z O.O. products are EC certified. We offer our own transport – prices are determined on a case-by-case basis, based on each offer. We issue VAT invoices. Short lead times! Machines in various, customized configurations and sizes are available! Contact us today.

Condition: new, Year of construction: 2025, The perfect paint set for car rims, motorcycle frames or other smaller things with a rail system and trolleys. Powder coating oven 1500 x 1500 x 1800 mm Powder coating booth 2000 x 1800 mm Oven / Dryer Technical data: Working dimension 1500 x 1500 x 1800 mm • Power consumption: 20 kW • Maximum operating temperature: 230 ° C Equipment: • Trolley inside, • Outdoor trolley, • True Fan Cooking (Equal temperature throughout the furnace), • Locks for safe opening and closing. Powder cabin: Rcsded S N R Ujpfx Airoh Working dimensions: 2000 x 1800 mm 2.2 kW fan power Fan capacity 10,500 m³ / h Very quiet operation Automatic filter cleaning CHOOSE BUMEX SP. Z O.O. Very high quality of the machines offered on the market. Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our clients. All products of the brand BUMEX SP. Z O.O. have WE certificate. We offer our own transport - prices are agreed each time for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please do not hesitate to contact us.

Condition: used, ITW Gema QCS 03 25-310 Complete Automatic Powder Coating Line, Powder coating system, Used machine Manufacturer / System: ITW Gema AG (Switzerland) & Recycolor Kft. Type / Model: GEMA QCS 03 25-310 (Powder coating booth) Year of manufacture: 2008 Serial Number: 5008-03012 (GEMA) / 16/2008 (Recycolor) Condition: Used, good industrial condition Dimensions and capacity: - Current layout footprint: 27 m x 18 m (system components can be reconfigured or modularly installed according to buyer needs) - Maximum workpiece size: 2500 x 800 mm - Conveyor line speed: High-capacity, 2 m/min - Exhaust air volume (booth): 16,000 Nm³/h - Cyclone dust collector extraction capacity: 8000 m³/h - Permissible organic powder concentration: 25 g/Nm³ (certified powder), 10 g/Nm³ (uncertified powder) - Zone 22 Main system components and technical specifications: 1. Surface Pre-treatment Tunnel (Recycolor Kft.): - Continuous multi-zone degreasing, (phosphating), and rinsing system. - Final rinse zone: DI (demineralized) water rinse stage. Rsdpfx Aio Af I Hderjch - Construction: Watertight PP sheet housing with drip zones and partition plates to minimize cross-contamination. - Lower zone tanks equipped with internal filters, circulation pumps, and fitting assemblies. - Dehumidification / Exhaust: Fan extraction with droplet separator. - Control system: Fully automated PLC control. 2. ITW Gema QCS 03 25-310 Powder Coating Booth & Recovery System: - GEMA quick color-change booth with integrated overhead conveyor. - Double-sided automatic powder coating with 4+4 (total 8) spray guns with 2500 mm vertical stroke. - Pre-touch manual spraying area at the inlet for complex geometries. - Mono-cyclone powder recovery system and absolute filter with built-in exhaust fan. - Bottom cone with swing-out sieve unit for automatic or manual powder recycling. 3. Water Drying and Powder Curing Oven (Recycolor Kft.): - Fuel type: Natural gas - Main gas burner: Weishaupt WG30N/1-C/ZM-LN 3/4" W-MF (Max. output: 320 kW, supply pressure: 100 mbar) - Gas-infrared burners: INFRATEC / Honeywell CVI-r1 - VK4115V (24 units x 10 kW/unit = 240 kW total power, max. 50 mbar) - Air recirculation: 2x MA-62/1440 fans (2 x 15,000 m³/h flow rate, 2 x 7.5 kW motor power) - Design: Thermal-bridge-free sandwich panels with internal framework and "A-shape" thermal lock entry/exit to retain internal hot air. - Operating temperature range: Adjustable between 60 – 220 °C.

Condition: new, Year of construction: 2025, The BUMEX SP. Z O.O.company presents a powder coating booth. working dimension: Rcsdpfxsd S N Sco Airjh 4500x2300mm 6 x polyester filter Automatic filter cleaning with adjustable range from 10-1200 sec. 2 x fan 2.2 kW, 10,500 m³/h (Total 21,000 m³/h) 2 x LED lamp Delivery time 14-21 days Our cabins are characterized by a very high quality of workmanship, safety of use and selection of cabin parameters to the existing building. We advise on the selection of paint booths, dust extraction systems, exhaust systems and industrial recuperation. CHOOSEBUMEX SP. Z O.O. Very high quality of machines offered on the market. Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our customers. All BUMEX SP. Z O.O. are WE certified. mdvncpiz We offer our own transport - prices are set each time for a given offer. We issue VAT invoices. e.g Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Feel free to contact us.

Year of construction: 2018, condition: new, FireMaster Morgan Thermal Ceramics FireMaster® Marine Plus FM-MP69/16X14640X610S SUPER DISCOUNT! 19 Euro pallets available 16 boxes on each euro pallet x 19 euro pallets = approximately 304 boxes Material dimensions: Thickness 13 mm Width 620 mm Length 14,640 mm Density kg / m3: 96 Price per box 100 EUR + VAT In total there are about 304 boxes. Total price 30,400 Euro + VAT, negotiable , FCA: Satu Mare / Romania Manufactured from FireMaster® Plus fibre, FireMaster® Marine blanket is a highly insulating blanket especially developed for fire protection Plus applications that are very space or weight sensitive Classification temperature FireMaster® Marine Plus blanket: 1200°C (2192°F) Fire reaction properties Non-Combustible in accordance with IMO FTP Code Part 1 Index < 0.5 when tested in accordance with UK MOD Defence Standard 02-713 Class A1 Reaction to Fire in accordance with EN 13501-1 Thermal insulation performance Thermal insulation at ambient temperatures R Values (m² K/W) and corresponding U values (W/m²K). For densities above 80 kg/m³ the values for 80 kg/m³ may be used Basis Thermal conductivity measured at 10°C using BS EN 12667 method 48 kg/m³ 0.0321 W/mK 64 kg/m³ 0.0319 W/mK 70 kg/m³ 0.03164 W/mK 80 kg/m³ 0.03144 W/mK Thermal conductivity at high temperatures Thermal conductivity (W/mK) at mean temperature measured using ASTM C201 method Rcedpfeh Rawujx Airsh Please check the attachment with the technical data. We reserve the right to make mistakes, changes and prior sale Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. Rodowzl Hxspfx Airoch * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, working width: 1,300 mm, overall weight: 7,500 kg, No minimum price – guaranteed sale to the highest bidder! Rcjdpfx Ao Af Hntjirjh TECHNICAL DETAILS Working width: max. 1,300 mm Number of spray booths: 1 Pump type: Wagner Number of spray guns: 4 MACHINE DETAILS Weight: 7,500 kg Number of transport packages: 7 EQUIPMENT Spray guns Documentation

Year of construction: 1998, condition: used, functionality: fully functional, Description: For sale is a large-format, professional BERKMANN surface spraying and painting system. The system was in productive use until recently and was used for high-quality painting work, including demanding high-gloss surfaces. It is currently still fully assembled and installed. This allows interested parties to inspect the existing scope of the system and the installation situation before dismantling and to document it for a later reconstruction. Technical data and equipment: • Large-area, filtered supply air ceiling panel, approx. 8,100 × 4,500 mm • Filter ceiling divided into two areas across its width • Large-area floor extraction system, approx. 8,100 × 3,650 mm, with grating • Supply air treatment, approx. 24,500 m³/h • Exhaust air treatment, approx. 24,000 m³/h • Supply and exhaust air fans / air treatment • Existing heating / hot water system with pumps and fittings • Air ducts and existing piping • Electrical system control / control cabinet • Cabin lighting • Sale includes the system in its current, on-site configuration Condition and use: Used, condition appropriate for its age. The system was in regular production use until recently. Previous use included high-quality surface work up to and including high-gloss coatings. An inspection of the still-assembled system is highly recommended. Rodsz Ikyropfx Airjch Sales and dismantling conditions: Sale is effective immediately. The system is permanently installed. Dismantling, removal, loading, and transport are the complete responsibility of the buyer and will be carried out at the buyer's expense. The buyer must organize the necessary specialist personnel as well as lifting, dismantling, and transport equipment. The complete dismantling and removal must be completed no later than July 31, 2027. Note: Technical specifications have been compiled based on available documentation, nameplates, and the current condition of the system. Specifications are without guarantee. The condition and scope determined during inspection shall be binding. Selling price: 19,500.00 EUR Price is net, plus any applicable statutory taxes and duties. Export, customs clearance, and import duties are the responsibility of the buyer.

Year of construction: 2021, condition: ready for operation (used), functionality: fully functional, FLOW & THERMAL Regenerative Thermal Oxidizer (RTO), 18,000 Nm³/h (2021) Complete industrial system for the treatment of process water containing Volatile Organic Compounds (VOCs), consisting of stripping columns and a three-chamber Regenerative Thermal Oxidizer. Manufactured by Flow & Thermal Solutions / TECAM in 2021, the equipment was installed at a PET production plant and remained operational until the factory closed on 27 November 2025. The system removes VOCs from the water by means of air stripping and subsequently destroys them in the RTO through high-temperature thermal oxidation. Heat recovery through ceramic media helps reduce natural gas consumption. Main features • Manufacturer: Flow & Thermal Solutions / TECAM • Year: 2021 • Serial number: F002 • RTO nominal capacity: 18,000 Nm³/h • Configuration: three-chamber regenerative RTO • Fuel: natural gas • Honeywell / Eclipse TJ 200 burner • Burner output: 58–586 kW • Electrical supply: 400 V, 50 Hz Rcjdpszvcknsfx Airsh • Electrical power stated on the nameplate: 40 kW • 30 kW Soler & Palau ATEX main fan • Siemens PLC automation with HMI touchscreen • LEL monitoring, purge, dilution, bypass and pneumatic valve systems • Vertical stack: 10 m high, diameter: 800 mm • CE marked Performance and operation The equipment operated at actual flow rates close to its nominal capacity, with recorded values ranging from approximately 16,400 to 17,900 Nm³/h. The latest available emissions test, carried out by DEKRA in December 2023, recorded the following values: • TOC: 13 mgC/Nm³ • NOx: 3–4 mg/Nm³ • CO: 125–153 mg/Nm³ During the tests, the equipment operated at an approximate temperature of 775–780 °C, with a treated water flow rate of 3.5 m³/h. Stripping columns The system includes: • Original stripping column, designed for approximately 6 m³/h. • Second Tecnium SLFKK9 stripping column, manufactured in PPH, with a nominal capacity of 8 m³/h and a maximum capacity of 10 m³/h. The second column was installed, but it is currently dismantled and lying on the ground after being knocked down by strong winds during the winter. It has a hole in the base which, according to the available information, is considered potentially repairable. The Tecnium column is equipped with internal packing, distributors, a mist eliminator, connections, drainage and provisions for integration with the existing control system. Condition and maintenance The system remained operational until the final closure of the plant in November 2025. The latest preventive maintenance was carried out by TECAM in June 2025 and included mechanical and electrical inspection, burner, fans, stripping columns, instrumentation, valves and functional testing. The equipment was operational, although maintenance work is required before recommissioning, mainly involving: • Process valves • Internal insulation of the towers • Ductwork and seals • Main fan impeller and expansion joints • Repair of the base of the second stripping column TECAM technical documentation is available regarding the recommended works, and several spare parts are also available. Scope of supply The system includes: • Three-chamber RTO • Combustion chamber • Burner and gas train • Main fan • Two stripping columns • Dilution and purge system • Hot bypass • LEL analysers • Stack • Ductwork • Electrical cabinets and controls • Platforms, ladders and support structures • Available spare parts

Condition: used, Year of construction: 2020, Spray coating machine Manufacturer: Homag Type: PROFI GSF100/P/13 Year of manufacture: 2020 Technical data Spray machine for automated coating of furniture components, doors, stairs, and interior design elements with water-based or solvent-based paints. - Sled runner with a spray arm to accommodate four spray guns - Workpiece transport with a vacuum conveyor belt with additional paper support - Feed speed: 1 - 4.5 m/min - Average coating speed: 1.5 - 2.5 m/min - Working height: 900 mm - Extraction volume: approx. 10,000 m³/h - Diameter of extraction nozzle: 350 mm - Electrical connection power (without additional equipment): 10 kW - Compressed air consumption (without spray application): approx. 150 nl/min Workpiece parameters Workpiece width: 100 - 1300 mm Workpiece length: 300 - 3000 mm (without additional workpiece support) Workpiece thickness: 5 - 60 mm Workpiece weight: max. 80 kg Workpiece material - Chipboard, MDF and HDF boards - Solid wood components - Lightweight panels - The difference in height between workpieces may be a maximum of 2 mm Coating material - Paint based on water or solvent Electrical parameters - Operating voltage 400 volts, 50 Hz Roller table for machine infeed/outfeed - Powered roller table for automatic transport of workpieces Rcjdpfxs Adr Hxj Airoh Mobile paper roll trolley - For quick changing of the unwinding paper roll Touchscreen operation - Machine operation is performed via a touchscreen control panel, which is ergonomically positioned on the operating side of the machine. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Integrated lighting is also available as an option. Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Rjdoxa Hx Ropfx Airoch Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: used, Sturm Coating Coating System For sale is a complete industrial Sturm robotic painting system manufactured in 2019. This automated coating system was used for series production coating of components and comes from an industrial production facility. The used painting line includes, among other things, a painting booth, drying and cooling zones, conveying technology, and several KUKA and Yaskawa industrial robots. The system is complemented by a thermal exhaust air purification system. Due to the automated system design, the robotic painting system is particularly suitable for industrial applications in the automotive industry, metal processing, and series production. Technical data & scope of supply: Manufacturer: Sturm (system) / KUKA & Yaskawa (robots) Year of manufacture (main system): 2019 Previous operation: 3-shift operation (condition appropriate for age) System components: Units, drying and cooling zone, painting booth, loading and unloading station Included robots / peripherals: Several spare KUKA robots (models KR 210L 150-2 / KR 210 2, years of manufacture 2006–2012) Associated robot control cabinets 2x Yaskawa robots EPX 2900 1x Thermal post-treatment / exhaust air purification system (VeniaKab / RNV) Condition notes: Control technology: According to the in-house maintenance department, it is at the state of the art. Electrical & mechanical: Mostly in a condition appropriate for age or good condition. Cybersecurity data deletion: For security reasons, all hard drives of the robots and PC-based stations have been removed. "Everything from one source: We will gladly offer you a suitable bank financing option for your project." More items - new and used - can be found in our shop! Rodpfxezka Sfs Airsch International shipping costs on request!

Condition: used, Powder coating booth with multi-cyclone and after-filter For sale is a professional, complete industrial system for powder coating: A Gema Volstatic powder coating booth, type MRS (multi-cyclone recovery system with after-filter). This system represents the highest Swiss quality, extreme robustness, and maximum efficiency in powder recovery. Thanks to its generous dimensions, it offers plenty of space for long and bulky workpieces. It is ideal for industrial companies, powder coaters, or workshops looking for a powerful and reliable system. Technical data • Manufacturer: Gema Volstatic • Type: MRS (multi-cyclone and after-filter system) • Electrical connection: 3 x 380 V / 50 Hz • Equipment: Booth substructure with inlet, manual coating opening, and spray gun travel slots. • Recovery: Highly efficient multi-cyclone with cleaning flap and powder collection container. • Extraction / After-filter: Powerful fan unit with integrated pressure monitoring and automatic flushing air filter cleaning. • Fan power after-filter: 15 kW with 12 filter plates (air volume flow: 8000 m³/h) 22 kW with 16 filter plates (air volume flow: 12000 m³/h) • Fan differential pressure: 4.2 kPa (at 8000 m³/h) or 4.5 kPa (at 12000 m³/h) • Compressed air connection: Min. 6 bar / Max. 10 bar (Recommended: 7 bar) • Compressed air consumption (flushing air filter box): Max. 18 Nm³/h • External dimensions: approx. Height 3.20 m × Length 8.50 m × Width 1.84 m • Internal dimensions (usable space): approx. Height 2.40 m × Width 1.84 m Item location: • 48683 Ahaus / Ottenstein (Münsterland, North Rhine-Westphalia) Important pick-up & dismantling options (Please note): Option 1: Dismantling by the buyer The system must be professionally dismantled and transported by the buyer. Option 2: Our "all-inclusive package" (dismantling by us) Alternatively, we will take over the complete, professional dismantling of the system for you. Fixed price for this: 7,500,- € net (plus VAT). Rcjdpfxjz Nyqwj Airjh "Everything from one source: We would be happy to offer you a suitable bank financing option for your project." More items - new and used - can be found in our shop! International shipping costs on request!

Year of construction: 2020, condition: used, Offered for sale is a manual powder coating booth with a cartridge filter system. Technical data: Usable volume: 9.5m³, airflow rate: 12000m³/h, downward air velocity: 0.25-0.3m/s, total filter area: 160m², maximum powder melting point: 220°C, maximum dimensions X/Y/Z: 2200mm/200mm/2000mm. Control system: Integrated spray gun and control unit for manual powder coating. Equipment: Booth, platform, filter system, eight cartridges. Operation: 2020/2021 two-shift operation, subsequently approx. 30% daily utilization. System documentation available. Inspection possible by arrangement. Rcjdpfx Aez Rn Dnoireh

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. Rsdpfx Ajwzmcbeiroch • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.