Used horizontal band saws - half-automatic - cutting range 0-300mm for sale (120)

Condition: new, cutting diameter 220 mm saw band length 2450 x 27 x 0,9 mm table height 915 mm band speed 35 + 70 m/min connected load frequency 400 V capacity 90 degrees: round 220 mm capacity 90 degrees: square 210 x 210 mm capacity 90 degrees: flat 230 x 185 mm total power requirement 1,2 kW weight of the machine ca. 240 kg dimensions of the machine ca. 870 x 1550 x 1740 mm The Zimmer Z241/R is a self-lowering saw for miter cuts from 0 ° - 60 ° left. After the cut, the machine stays through one Safety limit switches stand. The reduction is infinitely variable Hydraulic system adjustable. The saw arm can be raised after the cut any position. The saw arm remains at the desired position stand. Iijdofgyh Nspfx Apmed The Z241 / R has the following features: Hydraulic cylinder, emulsion pump, eccentric tensioner, base, saw band, 400V Connector -16A- The machine is completely assembled and delivered ready for use.

Condition: new, cutting diameter 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: round 260 mm capacity 45 degrees: square 250 x 250 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 170 x 170 mm capacity 60 degrees: round 180 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3320 x 27 x 0,9 mm engine output 1,5 / 1,8 kW weight 670 kg Electro-hydraulic semi-automatic band saw SHARK 332 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Some features: New centralized switch console on an articulated arm. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Turntable (on roller bearings of 420 mm with preloaded thrust bearings assembled). Double belt speed (40/80 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base designed to completely contain the coolant, even with maximum angle cuts. The coolant pan (provided with an electric pump for lubrication and Cooling of the saw band) and the chip drawer (can be replaced by a Chip conveyor to be replaced - see special accessories) are in the base frame built-in. Preparation for installing the minimum blade lubrication kit Isdpfefg E H Usx Apmoid (Optional, in addition to the conventional standard lubrication with emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Adjustable length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: new, cutting diameter 300 mm saw band length 3320 x 27 x 0,9 mm band speed 40/80 m/min total power requirement 1,5/1,8 kW weight of the machine ca. 670 kg How it works in the CCS version: After the material has been advanced and Once the vices have closed, the cutting process begins. The lowering is done by its own weight and is controlled by a spring balanced and a hydraulic brake cylinder regulates when the cut is carried out, the saw arm is moved by hand to the necessary position for the feed of the material is pushed up. Electrical panel (marked cable connection, indicator light for Ready for operation, safety main switch provided with padlock, Switch or speed switch, emergency stop, thermal magnetic protection, Low voltage system 24 volts) Electronic tape tension converter with on-screen display. Manual vice with quick lock Base frame with coolant tray and chip drawer, which has a Motorized chip conveyor (accessory) can be replaced. Electric coolant pump for cooling and lubricating the saw blade. Chip clearing brush Adjustable precision stops to make cuts of the same length. Machine is intended for pallet truck transport. Iiodpfx Apsfg E H Tomsd Bimetal saw band for solid and profile material Tools and instructions for use

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm vice 285 mm turning speed range: 36/72 m/min dimensions of saw-band 2950x27x0,9 mm total power requirement 1,5 / 1,8 kW weight of the machine ca. 485 kg dimensions of the machine ca. 1700 x 1000 x 1800 mm Electro-hydraulic semi-automatic band saw SHARK 282 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Semi-automatic function: At the start of the cycle: - Vice closes and motor starts – Saw head lowers for the cut – Motor switches off – Saw head rises – Vise opens. Semi-automatic dynamic system (manual lowering of the saw band bow up to to the desired position and cycle start via the manual button.) Some features: New centralized control console on an articulated arm to allow the operator can be easily switched from any working position. Ijdpfx Ajfg E H Sopmsid Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Large work surface with turntable on roller bearings, measuring 265 mm preloaded thrust bearing, mounted. Double belt speed (36/72 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base frame with pull-out coolant tray. Electric coolant pump for cooling and lubricating the saw band. Preparation for installing the minimum blade lubrication kit (Optional), in addition to the conventional standard lubrication Emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, power: 9 kW (12.24 HP), cutting width (max.): 450 mm, control type: CNC control, overall weight: 6,100 kg, Equipment: CE marking, documentation/manual, in production from 2023 / 1 shift only, 6200 hours band 6830 x 54x1,3 It is a highly efficient automatic,band-saw with multiple material feed. Bandsaw is designed for performance cutting of very hard and tough materials. This bandsaw is using extremely robust construction optimized with target to get maximum rigidity of machine and minimum vibrations. Stroke of frame and feeder stroke is realized by sharpened ball screws. Machine guarantees maximum possible power a precision. The machine is designed for vertical cuts. It is suitable for serial production in industrial premises. The machine is designed to saw steel materials, but also non-ferrous and light metals. However, we recommend consulting the manufacturer about this option. Conception of bandsaw is FCV= feeder-cut-main vice. Conception FCV enable cut material in automatic cycle with shortest possible end. Cutting parameters The shortest cutting mm 10 The smallest divisible diameter mm 30 The shortest rest during one cut mm 40 The shortest rest during automatic cut mm 90 Single step of material feed Min mm 3 Iijdpfxoykkqgo Apmed Single step of material feed Max mm 730 Multiple feed mm 19999 Performance parameters Blade dimensions mm 6830x54x1,3 Blade speed m/min 20-150 Blade drive kW 9 Pump of the cooling emulsion kW 0,16 Blade cleaning brush motor kW 0,12 Chip conveyor motor kW 0,12 Motor of the blade drive cooling kW 0,6 Frame ballscrew motor kW 0,5 Feeder ballscrew motor kW 1,5 Electric input Ps kW 17,7 Installed power Ps kW 12,8 Electrical connection 3 x 400V, 50Hz, TN-S

Condition: good (used), Year of construction: 2001, Separator TEBA 240 DG Ijdpsu Ekw Nofx Apmsid Round 240 mm Rectangular 230 x 230 mm Motor 1,5kW Dimensions: 1,950 x 1,650 x 1,000 mm Mitre saws 90° / -45° / +45°/ +60° Cutting speed: 40/80 m/min.

Condition: new, capacity 90 degrees: round 250 mm capacity 90 degrees: square 210 mm 290 x 210 mm saw band length 2.965 x 27 x 0,9 mm mm table height 940 mm band speed 25 - 90 m/min total power requirement 1,1 / 1,3 kW weight of the machine ca. 0,35 t dimensions of the machine ca. 1,3 x 0,8 x 1,5 m ATTENTION SPECIAL PRICE!!! (20347) Double miter metal band saw with: - Belt speed 25 - 90 m/min - Miter cuts up to 60° left and 45° right Iiodpfx Apefgyh Remsd - Ball-bearing rotary table for quick miter adjustment - Quick-action clamping stick can be moved - Quick release lever - Automatic cooling

Condition: new, capacity 90 degrees: round 250 mm capacity 90 degrees: square 210 mm 290 x 210 mm saw band length 2.965 x 27 x 0,9 mm mm table height 940 mm band speed 35 + 70 m/min total power requirement 1,1 / 1,3 kW weight of the machine ca. 0,35 t dimensions of the machine ca. 1,3 x 0,8 x 1,5 m ATTENTION SPECIAL PRICE!!! Double miter metal band saw with: - Belt speed 35 + 70 m/min - Miter cuts up to 60° left and 45° right Iiodpsd Iip Njfx Apmjd - Ball-bearing rotary table for quick miter adjustment - Quick-action clamping stick can be moved - Quick release lever - Automatic cooling

Condition: new, capacity 90 degrees: round 250 mm capacity 90 degrees: square 210 mm 290 x 210 mm saw band length 2.965 x 27 x 0,9 mm mm table height 940 mm band speed 25 - 90 m/min total power requirement 1,1/1,3 kW weight of the machine ca. 0,35 t dimensions of the machine ca. 1,3 x 0,8 x 1,5 m SPECIAL PRICE!!! Double miter metal band saw hydraulic semi-automatic with: - Hydraulic vice - Material height button - Cut monitoring by ammeter - Cutting pressure feed regulator - Belt speed 25 - 90 m/min - Miter cuts up to 60° left and 45° right - Patented, ball-bearing turntable for easy miter adjustment - Adjustable quick-release vise - Quick release lever - Automatic cooling Iiedpfxefgyh Sj Apmjd

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic Iisdpfx Apjfgyicjmsd · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use

Condition: new, cutting diameter 255 mm saw band length 2765x 0,9 x 27 mm cutting width 300 x 180 mm turning speeds 35 + 70 U/min total power requirement 1,8 kW weight of the machine ca. 450 t dimensions of the machine ca. 1,7 x 1,23 x 1,75 m SPECIAL PRICE!!! Double miter metal band saw, frequency converter hydraulic semi-automatic GBS 250 Super HA-I Easy • miter left 60° + right 45° • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Hydraulic vice can be moved sideways a. • Guided, high quality industrial bearings • Solid vice + machine casting • Large machine bed • Machine base with tool compartment and chip drawer • Cut monitoring by ammeter • Cutting pressure feed regulator • Support roller (infeed side) • Ball bearing turntable Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material Isdjfn Andopfx Apmsid 6. Open the vise

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request. Ijdpfofg E Hpox Apmeid

Condition: new, capacity 90 degrees: round 250 mm capacity 90 degrees: square 210 mm 290 x 210 mm saw band length 2.965 x 27 x 0,9 mm mm table height 940 mm band speed 35 / 70 m/min total power requirement 1,1/1,3 kW weight of the machine ca. 0,35 t dimensions of the machine ca. 1,3 x 0,8 x 1,5 m SPECIAL PRICE!!! Double miter metal band saw hydraulic semi-automatic with: - Hydraulic vice - Material height button - Cut monitoring by ammeter - Cutting pressure feed regulator - Belt speed 34 / 74 m/min Ijdpfxjd Iip Ro Apmsid - Miter cuts up to 60° left and 45° right - Patented, ball-bearing turntable for easy miter adjustment - Adjustable quick-release vise - Quick release lever - Automatic cooling Share of freight costs 120 EUR

Condition: new, Year of construction: 2026, Fully hydraulic lowering and lifting function of the saw frame Hydraulic opening and closing of the clamping device Automatic shut-off after cutting, return of the saw arm to the starting position Torsionally rigid saw frame made of cast steel (with multiple ribs) Hydraulic short-stroke cylinder for the clamping device Precisely ground carbide saw blade guides, adjustable Electric coolant pump Belt tension manually adjustable with display, incl. electric saw blade and cutting pressure monitoring Hydraulic vise (opening and closing) Rotating chip removal brush Oversized, solid round support table, rotating with miter cuts with a predefined cutting channel; miter setting manually adjustable, reading via scale Material stop 500 mm with scale Incl. saw blade with combi-tooth pattern 4/6 Machine color: - Saw frame RAL 7035 - Machine body RAL 7005 Iisdpscl Tc Aofx Apmod Motor - three-phase 400 V, frequency-controlled 1.5 kW Saw blade dimensions 2910 x 27 x 0.9 mm Flywheel diameter 325 mm Cutting speed 20-120 m/min Vise clamping width 320 mm Working height 760 mm Sawing range: at 0° = Round D 250 mm, Square 240 x 240 mm, Rectangle 320 x 190 mm Machine dimensions (W x D x H) 1480 x 1700 x 2000 mm Weight 420 kg Further accessories available upon request. DELIVERY: FREE TO YOUR DOOR (within Germany) NOT THE RIGHT MACHINE? WE ARE A FLOTT SUPPORT PARTNER AND CAN OFFER YOU ALL PRODUCTS FROM THE FLOTT RANGE! ASK FOR A QUOTE!

Condition: new, Year of construction: 2026, High-performance band saw machine with hydraulic saw frame lowering (control valve) for miter cuts from 0° to 60° right / 45° left Torsion-resistant, robust cast saw frame Powered chip removal brush Cut feed via frame weight Miter angle adjustment and clamping manual Quick-action, movable vise Electric coolant pump Precision-ground, carbide saw band guides (adjustable) Large-diameter round support table, rotates with the miter, miter scale visible from the operator side Easily removable chip tray Material stop 500 mm with scale Iodjxlhmyjpfx Apmoid Includes combination-tooth saw band 4/6. Technical Data Motor: three-phase 400 V, 1.5 kW Saw band dimensions: 2720 x 27 x 0.9 mm Flywheel diameter: 325 mm Cutting speed: 20-120 m/min Vise clamping range: 320 mm Working height: 760 mm Weight: 390 kg Machine dimensions (W x D x H): 1480 x 1700 x 2000 mm

Condition: new, Year of construction: 2026, Standard equipment: torsion-resistant, robust cast iron saw frame powered chip removal brush powerful industrial worm gear motor automatic shutdown after cutting is complete mechanical saw blade tension with electric blade breakage monitoring quick-release vise, adjustable hydraulic saw frame lowering with rapid feed function (infinitely adjustable) electric coolant pump precision carbide saw blade guides, ground (adjustable) large-diameter round support table, rotating with miter cuts, miter angle indicator (scale) facing the operator direct switchover from manual operation to lowering operation easily removable chip collection tray material stop 500 mm with scale including saw blade with combination tooth pattern 4/6. Technical data: Motor, three-phase, 400 V, pole-switching 1.1/1.5 kW Saw blade dimensions 2720 x 27 x 0.9 mm Flywheel diameter 300 mm Cutting speed 40/80 m/min Vise clamping range 275 mm Working height 978 mm Weight 370 kg Machine dimensions (W x D x H) 1150 x 1588 x 1477 mm Sawing range: see data sheet Further accessories available upon request. DELIVERY: FREE DELIVERY (within Germany) Iiodefg Eq Rspfx Apmsd NOT THE RIGHT MACHINE? WE ARE A FLOTT SUPPORT PARTNER AND CAN OFFER YOU ALL PRODUCTS FROM THE FLOTT RANGE! ASK FOR A QUOTE!

Condition: new, Year of construction: 2026, Compact, fully automatic band saw (also miter cuts up to 45°) Torsion-resistant, robust cast iron saw frame Driven chip removal brush Powerful industrial worm gear motor Automatic shut-off after cutting and subsequent raising of the saw frame to the continuously adjustable, preset starting position Mechanical saw blade tensioning with electrical blade breakage monitoring Ijdpfxotpg Sae Apmeid Minimum remaining piece length 180 mm, smallest possible diameter 5 mm Feed accuracy of 0.2 mm Electric coolant pump Precision carbide saw blade guides, ground (adjustable) Easily removable chip collection tray Including saw blade with combi-toothing 4/6 Machine color: - Saw frame RAL 7035 - Machine body RAL 7005 12-month warranty for single-shift operation Motor: Three-phase, 400 V, pole-changing (kW) 1.1/1.5 Saw blade dimensions (mm) 2720 x 27 x 0.9 Flywheel diameter (mm) 300 Cutting speed (m/min) 40 – 80 Clamping width (mm) 275 Working height (mm) 768 2220 x 1650 x 1730 mm Weight (kg) 495 DELIVERY: FREE (within Germany) NOT THE RIGHT MACHINE? WE ARE A FLOTT SUPPORT POINT PARTNER AND CAN OFFER YOU ALL PRODUCTS FROM THE FLOTT RANGE! ASK FOR A QUOTE!

Condition: new, 1 brand new semi-automatic horizontal band saw machine with double mitre Make: HUVEMA / Beka-Mak, Origin Türkiye Model: HU 230 DGH-4 / BMSY 230 DGH Technical data: Cutting range: Round 230 mm Rectangle 320 x 130 mm Square 230 mm -45 ° Round 180 mm -45 ° Flat 230 x 100 mm -45 ° Square 150 mm +45 ° Round 210 mm +45 ° Flat 230 x 160 mm +45 ° Square 180 mm +60 ° Round 120 mm +60 ° Flat 120 x 100 mm +60 ° Square 100 mm Working height 795 mm Main drive motor power 1.0 - 1.3 kW, 400 V, 50 Hz Motor power coolant pump 0.12 kW 2 speeds 35 / 70 m/min Saw blade dimensions 2730 x 27 x 0.9 mm Dimensions L x W x H 1350 x 700 x 1300 mm Weight 415 kg Accessories / Special features: • Semi-automatic operation • Hydraulically clamping vice via foot pedal • Mitering on both sides using a swivel frame o The material to be sawn remains straight in space! o No turning of the material during miter cuts! o High efficiency with enormous time savings! • Preset precision stops 0°, 45° and 60° left and 45° right • Replaceable work table • Hydraulic vice, can be moved sideways to the left and right • Adjustable length stop 500 mm for cuts of the same length • The lowering of the saw arm is continuously regulated by a hydraulic cycle, after sawing the arm moves back up automatically and the vice opens • Coolant system • Chip brush • Pivoting control panel • Electric safety switch for blade tension and saw blade cover • Emergency stop switch • CE-compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 D - 44143 Dortmund-Wambel Iiodpjvyidmefx Apmjd

Condition: excellent (used), Year of construction: 2003, cutting diameter 128 mm saw band length / mm table height / mm Iijdpfx Apoxbh Hfjmsd

Condition: new, Model Name Shark 281 SXI evo Iiodegvkglepfx Apmjd

Condition: new, Model Name Iedpogvkctefx Apmsid Shark 282 SXI evo

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm capacity 45 degrees: flat 220 x 200 mm capacity 45 degrees: round 230 mm capacity 45 degrees: square 200 x 200 mm capacity 60 degrees: flat 140 x 100 mm capacity 60 degrees: square 100 x 100 mm capacity 60 degrees: round 150 mm vice 285 mm turning speed range: 36/72 m/min dimensions of saw-band 2950 x 27 x 0,9 mm Iisdpfx Apsxaa S Remod total power requirement 1,5 / 1,8 kW weight of the machine ca. 460 kg dimensions of the machine ca. 1150 x 1970 mm Equipment: - robust electro-hydraulic semi-automatic band saw (INDUSTRY) - with miter cuts from 45° right to 60° left * Miter adjustment via large turntable - MEP microprocessor control EVO to control all functions * front right, rotatable - optional manual or automatic lowering of the saw bow * stepless adjustment of the saw bow lowering - saw band guide made of hard metal plates - hydraulic saw band tension - including digital value display - 2x saw band speeds - 1x BI-metal saw band - 1x angle stop - chip removal brush - machine base frame with forklift pockets - operating instructions in German Functioning of semi-automatic operation: - electro-hydraulic clamping of the vice - electro-hydraulic lowering of the saw bow - electro-hydraulic raising of the saw bow - electro-hydraulic opening of the vice SPECIAL ACCESSORIES INCLUDED: - MEP LubeCut micro dosing device

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 200 mm capacity 90 degrees: square 230 x 230 mm capacity 45 degrees: round 190 mm capacity 45 degrees: flat 180 x 180 mm capacity 45 degrees: square 180 x 180 mm capacity 60 degrees: round 120 mm capacity 60 degrees: square 110 x 110 mm capacity 60 degrees: flat 110 x 110 mm vice 285 mm turning speed range: 36 + 72 m/min dimensions of saw-band 2950 x 27 x 0.9 mm Control MEP NC coolant tank 95.0 l total power requirement 1.5 / 1.8 kW weight of the machine ca. 435 kg dimensions of the machine ca. 1000 x 2000 mm Features: - Robust electro-hydraulic semi-automatic band saw (INDUSTRY) - With miter cuts up to 60° - MEP EVO microprocessor control for controlling all functions * Front right, rotatable - Optional manual or automatic saw bow lowering * Continuously adjustable saw bow lowering - Saw blade guide made of carbide plates - Hydraulic saw blade tensioning - including digital value display - 2 saw blade speeds - 1 bi-metal saw blade - Coolant system - 1 angle stop Iodpjw U U Uwsfx Apmjid - Chip removal brush - Machine base with forklift pockets - Operating instructions in German Functioning of semi-automatic operation: - Electro-hydraulic clamping of the vise - Electro-hydraulic lowering of the saw bow - Electro-hydraulic raising of the saw bow - Electro-hydraulic opening of the vise

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm capacity 45 degrees: flat 220 x 200 mm capacity 45 degrees: round 230 mm capacity 45 degrees: square 200 x 200 mm capacity 60 degrees: flat 140 x 100 mm capacity 60 degrees: square 100 x 100 mm capacity 60 degrees: round 150 mm vice 285 mm turning speed range: 36/72 m/min dimensions of saw-band 2950x27x0,9 mm total power requirement 1,5 / 1,8 kW Iisdpfx Apoxaatbsmsd weight of the machine ca. 460 kg dimensions of the machine ca. 1150 x 1970 mm Equipment: - robust electro-hydraulic semi-automatic band saw machine (INDUSTRY) - with miter cuts from 45° right to 60° left * Miter adjustment via large turntable - MEP microprocessor control EVO to control all functions * front right, rotatable - optional manual or automatic lowering of the saw bow * stepless adjustment of the saw bow lowering - saw band guide made of hard metal plates - hydraulic saw band tension - including digital value display - 2x saw band speeds - 1x BI-metal saw band - coolant device - 1x angle stop - chip removal brush - machine base frame with forklift pockets - operating instructions in German Functioning of semi-automatic operation: - electro-hydraulic clamping of the vice - electro-hydraulic lowering of the saw bow - electro-hydraulic raising of the saw bow - electro-hydraulic opening of the vice

Condition: new, cutting diameter 220 mm Isdpfx Aed Iip Tjpmsid saw band length 2455 mm table height 850 mm cutting width 230 mm cutting speed 25 - 80 m/min dimensions of saw-band 2455 x 27 x 0,9 mm 90 mm 90 mm 90 x 100 mm 150 Impact energy 150 Air consume per blow 150 x 210 220 mm stroke back stop 210 mm cross-slide 230 x 185 total power requirement 1,2 kW weight of the machine ca. 0,24 t dimensions of the machine ca. 1,2 x 0,6 x 1,7 m SPECIAL PRICE!!! -Miter cuts up to 60° left - Cutting speed 25 - 80m/min. - Vice with quick release device -Carbide saw band guide -Tape tension control -Electr. automatic cooling Auto-Cut-System = 3 step system -Automatic saw frame lowering via the hydraulic cylinder -Infinitely adjustable feed -with limit switch - rapid lowering of the saw frame from the rest position to the workpiece, then switch to normal saw feed -Manual mode