Used hydraulic single column presses over 125t for sale (37)

Year of construction: 1980, operating hours: 7,663 h, condition: used, pressure 320 t throat 800 mm stroke 630 mm distance between table / ram max. 1000 mm ram head dimension 710 x 600 mm Cpjdped Ih Nrefx Agkew table-size 800 x 1200 mm work height max. 1015 mm quantity of oil 1100 l Number of working hours 7663 h weight of the machine ca. 15 t dimensions ca. 1600 x 2200 x 4800 mm dimensions of switch cabinet ca. 1200 x 400 x 1800 mm Tested for function. During the test run it is noticed that the press ram not 100% leak-proof. In addition, the cable for manual operation was mended several times. Upper cover is missing, since this was dismantled by the customer due to crane use. Operating instructions and electrical plans available.

Condition: excellent (used), Year of construction: 2021, operating hours: 50 h, Machine for sale in good condition it has low operating hours. Cjdpfx Agsxbb Hrskepw

Condition: new, Year of construction: 2025, functionality: fully functional, 125 T C-Frame Servo Press with 50 T Ejector, DUPLOMATIC Hydraulics Reduced power consumption by up to 40% compared to conventional motors, thanks to servo-hydraulics. TECHNICAL DATA: - Press capacity: 20–125 T (adjustable) - Maximum installation height: 1000 mm - Usable table surface: 2200 x 750 mm - Usable ram surface: 980 x 750 mm - Ejector cylinder capacity: 50 T - Ejector cylinder stroke: 200 mm - Frame type: C-frame - Guide column diameter: Ø 100 mm (4 pieces, in corners) - Table height from floor: 870 mm - Overall dimensions approx. (W x D x H): 2400 x 2000 x 3300 mm - Approx. total weight: 8,700 kg - Clamping device for die centering: 50 mm diameter Cpjdjx Aqtqjpfx Agkjw - Prepared for vibration dampening plates: 30 mm - Prepared for ROBO connection: yes HYDRAULIC CYLINDER: - Piston stroke: 0–700 mm (adjustable) - Max. operating pressure: 245 bar - Return speed: 300 mm/sec - Ram speed under load up to 25%: 25 mm/sec - Ram speed under load up to 50%: 14 mm/sec - Ram speed under load up to 80%: 7 mm/sec - Ram speed under load up to 100%: 6 mm/sec - Idle speed: 300 mm/sec HYDRAULIC POWER UNIT: - SERVO hydraulic pump (brand: DUPLOMATIC): 143 L/min (1 piece) - SERVO motor power: 15 kW (1 piece) - Pressure accuracy during pressing stroke: +/- 5 bar - Pre-fill valve: NG-160

Year of construction: 1992, condition: used, machine/vehicle number: 530, The STEINER hydraulic press was manufactured and developed with practical aspects in mind. The hydraulic device is located on the hydraulic tank behind the press. Control blocks and valves are easily accessible from the outside and can be quickly replaced if necessary. The hydraulic radial piston pump is located on the drive console and is connected to the motor and pump mount via a coupling. The press stand is indestructible and torsion-resistant Sthal welded construction. The ironing board is screwed to the stand. The hydraulic cylinders are screwed to the press stand from above and guided through the mounting holes in the appropriate direction. The piston is connected to the piston rods via a wear ring. Four-sided, diagonal, flat grooves on the stand allow for very precise movement. Hydraulic cylinders are made of high quality material and are designed for high pressures. The piston rods are ground and hard chrome plated. The cylinder tubes are honed from the inside. Seals that have been maintained over many years are characterized by high quality and tightness. The piston rods are guided by guide bands, which are characterized by very low abrasion and a long service life. The control, control and monitoring devices for all control devices are installed in the control unit. Mutual locks ensure that no two program processes can run at the same time. The electrical control is located in a closed control cabinet. Pressing force - 8000 kN Operating pressure - 285 bar Installation height - 850 mm Stroke - 250 mm Table surface - 1550 x 1450 mm Ram surface - 1550 x 1450 mm Stand passage - 1800 mm Cpodpfopgktcex Agkow Lateral Breakthrough in the stand on the right and left Width x height - 1300 x 1075 mm Table top thickness - 155 mm Width of the machine approx. - 3100 mm Depth approx. - 4300 mm Height approx. - 4660 mm Table height above hallway - 500 mm Table height under hallway - 755 mm Drive power - 55 kW Oil requirement approx. - 1400 liters Total weight approx. - 60 tons

Year of construction: 1974, condition: used, machine/vehicle number: 82, Hydraulic frame press for sheet metal stamping with a force of 630 tons, designed for cold stamping. The vertical frame press with a welded construction consists of a table and an upper plate that are connected with screws. An electrical cabinet is installed next to the press and an oil overflow tank is located deep in the foundation, which facilitates filling the press system with oil. The pressing units are removable, which makes their assembly and repair easier. The press is controlled with a button. The size of the slider stroke is ensured by adjusting the position of the end stop. 1. Nominal pressing force, tone 630 2. Rated working pressure of fluids, KN/cm 2,200 3. Slide stroke, mm 750 4. Slider speed, mm/s a) at idle speed 215 b) during the working stroke 10 c) during the return stroke 120 5. The greatest distance between the table and the slider, mm 1400 6. Distance between posts, mm 2200 7. Table dimensions, mm a) from left to right 2220 b) front to back 1800 8. Thickness of stamping plate, mm 220 9. Table height above floor level, mm 410 10. Nominal force of the hydraulic washer, tf 250 11. Hydraulic cushion stroke, mm 350 12. Ejector speed, mm/s a) when going up 51 13. Press size, mm a) from left to right 5070 b) front to back 3000 c) height 7065 Cjdpfepgkt Sox Agkepw 14. Press height above floor level, mm 5480 15. Weight of the press, kg 69400 Electric motor revolutions 1450 min-1 Operating voltage 400/230 V Mains frequency 50 Hz ± 1% Rated air pressure 0.7 Pa

Condition: refurbished (used), RETROFIT complete Pressing force: 1600 kN Installation height: 800 mm Stroke: 500 mm Table: 900 x 630 mm Ram: 750 x 450 mm Throat depth: 360 mm Downward speed: 200 mm Upward speed: 125 mm Machine height: approx. 3,500 mm Weight: approx. 7,000 kg Connection: 17 kW Cjdpfx Aew S Uazjgkjpw - a complete retrofit kit for unrestricted manual loading and unloading compliant with EC directives and CE equipment requirements, - new control cabinet with certified two-channel electronic PLC safety controller from Siemens (1512SP F or 1515F) for process control, featuring integrated control panel for the operating modes: setup with two-hand control, single stroke with two-hand control, and foot operation (only in combination with BWS); manual lever operation is no longer possible, - hydraulic safety block for monitoring the closing movement of the main cylinder, - position-monitored directional valve for the up and down movement of the ram of the main cylinder, - two-hand control device with two-channel monitoring of the two-hand synchronization at the press table (incl. 5m cable), - replacement of main and control pump motors, - replacement of seals on the main cylinder, - fine filter with contamination indicator, - the press is equipped with an electronic position measurement system (including teach-in function and display of the current ram position), eliminating the need for a mechanical cam switch. Main control panel integrated into the control cabinet (mounted on the right side of the machine): - 12" touch panel - Control buttons and switches for operating modes and drives - USB interface for data exchange - Light curtain Option: Drawing cushion

Year of construction: 1989, condition: ready for operation (used), machine/vehicle number: K 1283, A used bending machine from the manufacturer HMK. The pressing power up to 500 t Year of construction: 1989 Csdpfxsd Eg R Tj Agkspw Machine number: 1283

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, machine/vehicle number: 4701, pressing force: 394 t, table width: 51 mm, table length: 680 mm, stroke length: 200 mm, No minimum price - guaranteed sale to the highest bidder! TECHNICAL DETAILS Codpfx Aswr Dvyegkjpw Front: 510 mm Side: 270 mm Press stroke: 200 mm Clear opening: 455 mm Table Table size: 510 × 680 mm Power and Drive Press force: 394 t Motor power: 15 kW Speeds Downward speed: 350 mm/s Working speed: 4 mm/s Return speed: 300 mm/s MACHINE DETAILS Height: 2,710 mm Width: 1,530 mm Depth: 1,610 mm Machine weight: 6,620 kg

Condition: like new (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: STHP 80KN, total height: 1,320 mm, total width: 510 mm, total length: 200 mm, pressing force: 8 t, table width: 300 mm, overall weight: 110 kg, 1 Hydropneumatic press type STHP 80 kN Cpodpfet Rhb Iox Agkow Bmcbfntr with two-hand operation - floor model with and base frame The compact and handy table model has a hydropneumatic drive with pressure intensifier, which can increase the punching force by up to 5 times. The punching cylinder is pressurized with oil by the pressure intensifier during the working stroke and therefore has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders.

Condition: good (used), functionality: fully functional, total height: 3,500 mm, total width: 2,800 mm, total length: 1,200 mm, pressing force: 300 t, ID105830 Hydraulic press Cpodpfx Aowhc H Asgkjw Brand: Van De Graaf Type: HVK-300 Capacity: 300 tons

Year of construction: 1990, condition: like new (used), Quality WMW 250ton C frame hydraulic press for sale Cjdpjig Hzkjfx Agkepw The machine bed size is approximately 630mm x 850mm with an Opening/Daylight dimension of 300mm. The machine is fitted with a 150mm Packer plate which could be removed to allow for 450mm opening.

Year of construction: 2003, condition: excellent (used), Used Loire 2000ton hydraulic H frame press for sale Table dimensions ( x-y/mm) : 5000×2500 Slide dimensions ( x-y/mm) :5000×2500 Stroke ( x/mm) : 1700 Light at tdc ( x/mm) :2700 Lateral window ( x/mm) : 2900 Cushion in the slide (x/mm) : 3400×1900 Stroke of the cushion in the slide (x/mm) :150 Cushion stroke ( x/mm) : 400 Cushion power ( ton) : 600 Lateral moving bloster Brand Loire Power 2000 Ton Table dimensions X-Y 5000 x 2500 Slide dimensions (x-y) 5000×2500 Stroke 1700 Light at tdc 2700 Shut eight 1000 Lateral window Lateral window dimensions (x-y/mm) 2900 Internal slide Dimensions X-Y 3400×1900 Stroke 150 Work speed to 100% 22 mm/sec Strokes/min 37 mm/sec Strokes/min 400 mm/sec Strokes/min 350 mm/sec Cushion Power 600 Ton Stroke 400 mm Cushion table dimensions (x-y) 37001900 Accessories Accessories lateral moving bolster Overall dimensions Weight 310 Front 6250 Deep 5000 Height 9650 Conditions Machine conditions Working Electric plant conditions Working Year 2003 Cjdpfx Asn Sma Hsgkopw New hydraulic H frame press for sale complete with warranty