Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Bsdpot Tqy Eofx Ak Hedb Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Year of construction: 2022, condition: used, Number of sanding units 6 st. Sanding height max. 120 mm output 12 kw Bjdpfx Akeynntts Hodb

Condition: used, Year of construction: 2006, Tenoning spindle 2 St. Number of milling agregates 5 St. Spindle diameter 50 mm SCM Windor 40 R window production centre, manufactured in 2006 ----- This machine is part of the sale of a complete window manufacturing operation, Bjdpfx Aoyn R Imek Hsdb see stock number 1305-6979. Machines still connected and ready for demonstration Technical Summary: ----- - 2 long CNC-controlled slotting spindles - Optima 16: Drilling units for face and longitudinal drilling - ROTATEN: Angled window attachment - 3 long CNC-controlled profile spindles + top and bottom unit - Rebating carriage for small sashes - Workpiece return Options with additional costs: ----- - Used Leitz window and door tools for SCM Windor 40 R. Price: €10,000 - Separate OKOMA UF 3 rebating machine with compatible tools for SCM Windor 40 R systems. Price: €2,000 - Used chip extraction and filtration system for SCM Windor 40 R (See attached PDF for more information). Price 5.500 Euro (Technical specifications according to the manufacturer, without guarantee!)

Year of construction: 2022, condition: used, Number of sanding units 6 st. sanding width 45-165 mm Sanding height max. 45-92 mm weight 2200 kg Ecoline Q-SAND 6 For sale on behalf of a customer Bdsdpfx Ajxyafkok Hob ----- Full text as PDF attachment! Short description: Machine with infeed conveyor and automatic height detection. It has two grinding discs on top and two grinding discs on the bottom, each connected to a brush unit. Technical manufacturer's description: Ecoline Q-Sand: the ideal grinder for squared timber and more. Designed to work on both sides of the workpiece with three-dimensional adjustment, the Q-Sand guarantees maximum precision and uniformity. It is equipped with grinding discs, flap brushes, and a double disc for more effective material removal, thus improving adhesion for subsequent treatments. The Q-Sand can be installed in a production line or, due to its complete operational autonomy, can also be used independently. It is also ideal for window frames, beams, and custom-made products, and optimizes processing times with automated systems and advanced production control. ----- Price of the above-mentioned machine available upon request! ----- (Technical specifications according to the manufacturer - without guarantee!) All prices quoted are net prices, excluding VAT. The video is from the manufacturer Ecoline and shows a new machine.

Condition: ready for operation (used), Year of construction: 1998, overall weight: 16,500 kg, controller manufacturer: SIEMENS, This BURKLE BTF 1628 laminating press was manufactured in 1998. It features a max panel size of 1250x2550 mm, panel thickness range of 6-35 mm, and a heating plate dimension of 1600x2800 mm. Equipped with a Siemens control system and a total power requirement of 38 kW. Consider the opportunity to buy this BURKLE BTF 1628 laminating press. Contact us for more information. • Max Panel Size: 1250 x 2550 mm • Panel Thickness: 6 - 35 mm • Heating Plate Dimensions: 1600 x 2800 mm Bdedpsx D Ifmofx Ak Hob • Max Heating Temperature: 140° • Max Stroke: 230 mm • Total Power Requirement: 38 kW

Condition: ready for operation (used), Year of construction: 2018, controller manufacturer: SIEMENS, controller model: SIVATIC HMI, This WEMHÖNER Variopress Basic 1000S was manufactured in 2018. Ideal for efficient laminating processes, this machine ensures consistent performance. Consider the opportunity to buy this WEMHÖNER Variopress Basic 1000S laminating press. Contact us for more information. Additional equipment Bdedox D Hy Aspfx Ak Hjb • Including: 2 x paternoster magazines for film rolls Machine Benefits Technical Machine Benefits • Heating plate format (mm): 2850 x 1550 • Electric heating plate design: aluminum heating plate top • Total pressing force (kn): 2400 / chamber pressure max (bar): 6 / operating temperature max: 180 degrees celsius / batch or workpiece size max (mm): approx. 2460 x 1180 • Thermoplastic film in rolls, width of the film: approx. 1430 mm / thickness of the film (mm): approx. pressure chamber height (mm): max. Up to 180 • Connection values: installed power (kw): approx. 46 / required air pressure (bar): approx. 8

Condition: ready for operation (used), Year of construction: 2007, This DIMTER PROFIPRESS L2500 was manufactured in 2007. A robust used gluing press, it features a press bed of approximately 2500 x 1300 mm and a stable base frame. It includes a motor-driven multifunctional pusher and an automatic gluing station with a precision glue head. Ideal for both softwood and hardwood, it ensures even pressure distribution and high vertical pressure for low offset. Contact us for more information about this machine. • Workpiece capacity: • Lamella widths (for panels): 30–150 mm • Thicknesses: 11–60 mm • Input length: 800–2500 mm • Panel width: variable, up to max. 1300 mm • Filling width per cycle: min. 650 mm / max. 1300 mm • Max. filling area per cycle: 3.25 m² Bdjdpsx D I Nrefx Ak Hob • Note: Max. usable press width depends on individual lamella widths • In multi-lane operation, filling widths may vary by max. 15 mm • Minimum contact surface per press filling: ≥ 100 cm² • Press performance: • Specific pressing pressure (at 2500 x 60 mm): up to 1.6 N/mm² • Press bed and construction: • Press bed area: approx. 2500 x 1300 mm • Stable base frame with lower press table in stainless steel (ground electrode) • Upper pressure plate with hydraulic motor “anti-reb” feature for high vertical pressure and low offset • Special hydraulic pressure elements ensure even pressure over the joint and compensate tolerances • Quick-change stop ruler sets for panel thicknesses 19–40 mm; hydraulically movable to the current filling width • Integrated hydraulic unit for press force and hydraulic motors • Electrical: • Operating voltage: approx. 400 V / 50 Hz • Electrical connection value of press (without options): 7 kW • Electrical connection value for 40 kW HF generator: 56 kW • Controls and safety: • Control cabinet and control panel • Protective cover Additional equipment • Collection table extended to 3700 x 1300 mm (with stainless steel wood support) • Motor-driven multifunctional pusher • Additional individual pressure elements from above • Automatic gluing station with precision glue head • Feed system for different widths • Camera • Washing and rinsing device for glue head • Modem with software for online connection

Condition: used, Year of construction: 2001, Automatic tenoner 1 saw with diameter 500mm 2 plate-type spreaders 2 cups with diameter 40mm Bdsdpjyr Ri Sofx Ak Hob Pneumatic pressers Automatic carriage advancement Digital display Speed variator Total power 35 kW 400V Weight 3500kg

Condition: ready for operation (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 14344, General The DiscMaster 4TD is equipped with four rotating discs that oscillate across the entire workpiece width. With its disc-only technology, the machine offers exceptionally low operating costs. The combination of rotation and oscillation delivers outstanding results, and the wide range of available disc tools makes the machine extremely versatile. Two disc units on the infeed side, two disc units on the outfeed side Oscillation over the entire conveyor belt width Processes edges and cut-outs precisely from all directions and angles, delivering true 360° finishing through the overlay of rotation and oscillation Consistent tool wear, regardless of the workpiece’s placement on the conveyor belt Easy and quick tool change for mixed materials, as only four tools need to be changed Versatile applications due to the vast array of available options Deburring and edge rounding of punched parts as well as waterjet, laser, or plasma-cut sheets in a single pass Deburring and edge rounding of 3D punched parts Edge rounding and oxide layer removal in a single operation Edge rounding and eccentric finishing in one step Bsdpfx Aoyywr Dek Hjdb Processing of small parts from 20mm diameter Processing of coated or galvanized sheets Processing of steel, stainless steel, and aluminum…

Condition: good (used), Slotted disks, window milling tools, indexable inserts, window construction tools -Slit discs, milling tool for: wooden windows Bsdpfob A Rg Sjx Ak Hedb -EXACTLY -Take: Ø 50 mm -1x pallet tool -different sizes -Weight including pallet: 346 kg

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Circular saw unit Motor power: 3 kW Saw motor speed: 3,000 rpm Circular saw diameter: 400 mm Max cutting height: 125 mm ----- Tenoning shaft Quantity: 01 Shaft diameter: 50 mm Shaft length: 320 mm Motor power: 7.5 kW Shaft motor speed: 3,200 rpm Max tool diameter: 320 mm ----- Profiling spindles (2) Shaft diameter: 50 mm Shaft length: 320 mm Motor power: 7.5 kW Shaft motor speed: 6,000 rpm Max tool diameter: 240 mm ----- Bdedoyk Df Depfx Ak Hsb Strip recovery unit Quantity: 01 Shaft diameter: 30 mm Motor power: 2.2 kW Saw motor speed: 6,000 rpm Strip recovery saw diameter: 200 mm

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, Unicontrol 12 Consisting of: Cut-off unit (item A), Tenon and slotted spindle (item C), Transfer belt (Pos. I), profiling spindle (Pos L), profiling spindle (Pos. N), Profile shaving unit vertical right (Pos. P) For the production of individual parts and elements in frame-by-frame or serial production. Consisting of a cross processing unit and a longitudinal processing unit connected to a transfer belt. Working width 40-140mm (See pressure ruler left 40 - 140 mm) Working height 40-120mm Workpiece length min. Bsdpfx Asumci Sok Hedb approx. 275 mm + 1 x end profile length Long machining: approx. 220 mm + 2 x end profile length Workpiece length max. 3500 mm The part dimensions depend on the machine equipment, production type and tool assignment. A final definition of the part dimensions is only possible after receipt, inspection and approval of the complete and final layout drawings. Cross machining: Table feed Motor power 0.3 kW (0.4 HP) Pre-set feed speed for cutting, profiling and return 3-25 m/min Vario table with (studio window production possible) The clamping length of all tenoning and slotting spindles can be used without a tool blank. Workpiece clamping by means of a clamping bridge. Operated by a clamping cylinder installed under the table. NC-controlled long fence mounted on the slotting table. Studio window device Swivel angle max. +/- 75° The minimum workpiece length for slanted windows depends on the angle and the width of the wood. Possible part dimensions for slanted window production Angle Max. Min. Working width Workpiece length +/-75° 80 mm 800 mm +/-70° 120 mm 490 mm +/-60° 240 mm 360 mm +/-90° 350 mm 185 mm For angles greater than 60° only counter processing Commission not documented 1)NC automatic angle adjustment for machining angled parts Splinter protection by means of overtravel counter Over the entire spindle length of the tenoning and slotting spindle for 90° machining Manually trackable counter-rail for angled part machining 2) Additional counter-rails

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, WEINIG Unicontrol UC 10-5 Window Production Machine Bdedpfx Aexmr N Iek Hob 1. Electronically controlled crosscut saw with laser switching between saw cutting and zero-point wheel, 3 kW motor 2. Grooving spindle 50 x 630 mm for tools 6 x 80 mm, 15 kW motor 3. Longitudinal/synchronous profiling spindle 50 x 320 mm for tools 4 x 80 mm, 11 kW motor 4. Grooving spindle (between 1st and 2nd lifting spindle), D = 40 x 40 mm, axially indexed, 3 kW motor 5. Longitudinal profiling spindle 50 x 320 mm for tools 4 x 80 mm, 11 kW motor 6. Longitudinal profiling spindle 50 x 320 mm for tools 4 x 80 mm, 11 kW motor 7. Clamping spindle 40 x 150 mm, 3-position axial cycle, 2-position radial cycle, 3 kW motor Saw and grooving spindle on the right side, 3 kW motor Hardware spindle 40 x 150 mm, 3 kW motor Adjustable feed speed 6-12 m/min, 1.1 kW motor 4-position counter changer Electronic length stop, 3600 mm Workpiece return system with automatic rotating mechanism Automation package Interval-controlled sash support Double parts package Laminated fabric tables (for sanded surfaces) Pressure guide on the left, max. wood width difference 100 mm Machine in very good technical and visual condition

Condition: used, Number of spindles 3 St. Number of tools 8 St. Spindle diameter 50 mm Dimensions (L/W/H) 4250x1850x2300 mm ! MACHINE FUNCTIONALLY CHECKED AND READY FOR DEMONSTRATION ! !!! Technical description in RUSSIAN, more machine pictures as well as machinevideos - if available - at the end of this description as attached files !!! Bdjdsymf Ekjpfx Ak Hsb # 6988 Weinig Univar 6 CNC ..... ..... Technical details summary (please ask for possibly more included equpment) ..... ..... 1st profiling spindle: ..... ..... > spindle rotation direction: clockwise and reverse for rip-off free outside profiling of sashes > position: vertical right > number of tools: 1 pcs. > length of spindle: 120 mm > number of revolutions: 6000 rpm > spindle diameter: 50 mm > tool diameter max.: 232 mm > engine: 11 kW 2nd profiling spindle: ..... ..... > position: vertical right > number of tools: variabel, CNC > length of spindle: 320 mm > spindle stroke vertical: variabel, CNC > number of revolutions: 6000 rpm > spindle diameter: 50 mm > tool diameter max.: 232 mm > engine: 11 kW 3rd profiling spindle: ..... ..... > position: vertical right > length of spindle: 160 mm > number of revolutions: 5850 rpm > spindle diameter: 40 mm > tool diameter max.: 210 mm > engine: 3 kW More features: ..... ..... > possible to work online: > monitor control: > Equipment for profiling small sashes: min. 500 mm > Control: PC-Nexus If the technical characteristics of this machines donnot fit with your requirements, please get in contact with us. Our longtime experienced team is looking forward to support you in technical adaptions or in finding a suitable machine for you! Technical details according to manufacturer - without guarantee!

Condition: used, Year of construction: 2012, Number of boring spindles 5 St. Working width 20-230 mm Bodpfx Aeyk Iddjk Hjdb Working height 8-160 mm

Condition: new, Year of construction: 2026, Number of boring spindles 6 St. Working width 20-230 mm Working height 8-160 mm Bsdpfeyk Icmsx Ak Hodb

Condition: used, Year of construction: 1993, voltage 220 V Bdjdpfx Akjyk Ibio Hsb collets 8mm Motor output 1,8 kW

Condition: new, Year of construction: 2026, working length 1000-1600 mm working width 40-150 mm Bodpfxeyk Iafo Ak Hsdb Thickness 10-80 mm

Condition: new, Year of construction: 2026, Working width 180 mm Feed motor 3 kW Bsdpfeyk H U Uex Ak Hodb weight of the machine ca. 2750 kg

Condition: new, Year of construction: 2026, Feed motor 5,5 kW total power requirement 58,3 kw Bdsdpfx Akjyk H T Re Hsb weight of the machine ca. 4000 kg

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 4960x1900x1700 mm Total power requirement 0 kW Weight 6000 kg Bdjdpfov Ucirjx Ak Hsb

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 4960x1900x1700 mm Bsdpfx Akev Uchnj Hsdb Total power requirement 0 kW Weight 6000 kg

Condition: excellent (used), Year of construction: 2002, machine/vehicle number: 10229, functionality: fully functional, operating hours: 25,000 h, power: 13 kW (17.68 HP), input voltage: 400 V, input current: 32 A, input frequency: 50 Hz, type of input current: three-phase, grinding belt width: 200 mm, grinding belt length: 1,800 mm, grinding height: 190 mm, height adjustment type: electric, actuation type: electric, total height: 1,890 mm, total length: 2,070 mm, total width: 1,020 mm, overall weight: 1,500 kg, Equipment: CE marking, documentation/manual, The machine is in very good condition, has been used only a little, with the option of refurbishment upon agreement. Bdsdpfx Ajyt Hkujk Heb

Condition: used, Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm # 2809 Weinig Unicontrol 6 ----- Technical Data Summary (Please inquire about any additional accessories included) Item 1: Cut-off saw ----- > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Maximum tool diameter: 400 mm > Motor power: 3.0 kW > Laser guide light for identifying the saw cut CNC-controlled length stop ----- > Length: 3,600 mm > Electronic length stop including positioned cut-off saw Item 2: Tenoning spindle ----- > Number of tools: 3 (stroke 2 x 100 mm) or 4 (Stroke 3 x 80 mm) > Tool clamping length: 320 mm > Pneumatic vertical spindle stroke: 240 mm for wood thicknesses 68 - 92 mm > Spindle speed: 3000 rpm > Maximum tool swing diameter: 320 mm > Spindle diameter: 50 mm > Maximum tool diameter: 360 mm > Motor power: 11 kW Item 3: 1. Profiling spindle (co-rotation and conventional) ----- > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm Bdodpfx Aksxtvgkj Heb > Spindle diameter: 50 mm > Maximum tool swing diameter: 232 mm > Motor power: 7.5 kW Item 4: 2. Profiling spindle ----- > Position: Vertical right > Number of tools: 3 (stroke 2 x 100 mm) or 4 (stroke 3 x 80 mm) > Tool clamping length: 320 mm > Pneumatic vertical spindle stroke: 240 mm for wood thicknesses 68 - 92 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Maximum tool swing diameter: 232 mm > Motor power: 11 kW 2 axially indexed feed rollers opposite the profiling spindle, for the production of narrow, short parts (e.g., glass-dividing muntins) Munch guide consisting of: Munch support strip from above in the area of ??the vertical right-han d profile milling unit and profiling spindle. Item 5: Horizontal top profile milling unit ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Spindle speed: 5,850 rpm > Maximum tool swing diameter: 130 mm > Axial travel: 52 mm, indexed in 2 positions > Radial travel: 125 mm, indexed in 2 positions Item 6: 3rd profiling spindle (fitting spindle) ----- > Position: Vertical right > Tool clamping length: 160 mm > Axial travel: 90 mm, indexed in 3 positions > Radial travel: 100 mm, indexed in 2 positions > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Maximum tool swing diameter: 210 mm > Motor power: 3.0 kW Further features ----- > Electric feed height adjustment including mechanical digital display and manual feed bar clamping > Rebating device for tear-out-free rebating > Double part package > Return conveyor for 1-person operation: swivel conveyor > Screen control > Angled window device > Electronic angle display for angled windows > Industrial PC with Windows PC control/NEXUS Extraction nozzle diameter: ----- Crosscut saw 80 mm Tenoning spindle 140 mm Profile spindle 1 140 mm Profile spindle 2 140 mm Grooving device from above 80 mm Hardware spindle 120 mm ----- Price of The above-men...

Condition: new, Assembly line consisting of: Item 1.0 / RU-CBM 4000 work table with running rail extended by 500mm for additional assembly an aluminum holder screwing machine for RU-CSA-SMB or RU-CSA-SMZD with RU-SH special screwdriver, support table Length 4000 mm, width 1400 mm, inclination of the working platform manually adjustable. Holder for fitting scissors or fitting punch. 16 pieces of swiveling counter-holders for hanging the wings, completely pneumatic Foldable for unhindered movement of the wings on the table surface. Device for scanning the sash fitting length for constant and variable/central gear seat for already drilled wings, colored Dimension recognition of the fittings. RU-SH, special screwdriver with pneumatic depth switch on carriage mounted, safety control, pneumatic height adjustment, Screw feeder with automatic shutdown of the filling container (Manual insertion for a second screw length on the special screwdriver upon request). RA-8, turret stop for 8 screw levels mounted on the carriage. RA-4, turret stop for 4 different wing widths Swivel table mounted. Pneumatic wing measurement sensing. operated, scanning range up to 2500mm simultaneous clamping of the scanning. PSF - Pneumatic tensioning device for sashes. Working height adjustable from 900 - 1000 mm. Support table covered with felt. Running rail extended to the left by 800 mm. Item 1.1 / 5035-1 Pneumatic swivel device of the work surface with foot valve Item 1.2 / 0500000 Holder matched to customer punch/scissors. For mounting a hardware punch provided by the customer or Fitting shears (third-party manufacturer) on the sash assembly table. Please specify make when ordering!!! Item 1.3 / 5597-7 Driving device for RU-CBM on semicircular rails. The castors are on the left and right of the base frame of the table mounted. Item 1.4 / 6354-6 3 double meters of semicircular rails 30 x 10 mm. Item 1.5 / 0730000 RU-SBL3000/40 free-standing fitting bearing, Length 3100 mm, depth 1250 mm, height 2200 mm, Stand frame on the front without supports, 40 compartments, divided into 10 compartments in a row by dividers and a continuous shelf at the top, Compartment size: width 280 mm, height 150 mm. Item 2 RU-CSA-SMB aluminum holder screwing machine with automatic Screw feeding and manual feeding of the aluminum holders from one traveling box with pneumatic positioning device, Screwdriver with depth cut-off with 4-fold turret stop. Pneumatic adjustment device in the y direction against 2 pieces 6-fold Revolver attacks. Feed container for manual feeding of rotary holders or clip holder in square shape 18.5 x 18.5. The holder is manually pushed into a channel in the box and with positioned in front of the screwdriver mouthpiece using a pneumatically operated slide. Profile depth max. 150 mm, screw spacing in the y direction max. 120 mm. Item 3 RU-S48-A6-350 column slewing crane for chain hoist, with 6 m aluminum boom Version with column, smooth-running boom and sliding chassis for swivel and trolley travel manually by pulling and pushing the load. Projection 6 m Construction height 4,461 m Lower edge of boom 3.722 m (top edge of boom 3.9 m) Swivel range max. 270° Painting of the steel construction in RAL 7035 The base plate is attached to the on-site hall floor At least 250 mm thick. Designed, of course, according to the valid STANDARD EN 13155 Bdedpfx Akjd Ih Hue Hob Warra...