Used Bevelling for sale (502)

Condition: new, machine/vehicle number: 2b58968e34fac93b429a256e9, empty load weight: 5 kg, maximum load weight: 12 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Quarter-shell mudguards in front of 1st axle Spare wheel holder for 1 electric wheel, with wheel mounting kit Spare wheel, same make as basic tires, steel rim Plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Low loader lashing eyes 3 pairs of lashing points, each 10 tons, integrated in the floor at the front 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x according to the rest of the neck area, distributed between them, spacing not greater than 1200 mm 1 x rear bevel 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cableVoltage converter for 12/24 volt operationNote! A 7-pin 12 volt socket is required on the tractor/tractor! (Required in conjunction with electrical voltage converter!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white/red rear lane departure lights 2 white position lights at the front Additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin interchangeable plugs at the front, with connecting cable1 x 7-pin agricultural plugVoltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 t GG. Customer risk. Country of registration / plates Pjdpfx Aasi Ri Nxohsrc Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, functionality: fully functional, Manufacturer: unknown Year of manufacture: unknown Psdjxq Eguspfx Aaherc Overall external dimensions (LxWxH) in mm: 230 x 140 x 400 Overall internal dimensions (LxWxH) in mm: 195 x 130 x 400 Shape: U-shape Anchoring: 2x floor anchoring Material thickness in mm: 5 Net weight in kg: 7 Special features: 1 side bevelled Condition: used / fully functional Function test: OK

Year of construction: 2023, condition: new, ProMax Professional Series CNC CNC PLASM PAPER BURNING machine TECHNICAL PARAMETERS working width 2000 working length 4000 Pjdpjnfvlvjfx Aahorc ventilated 8-section table travel speed up to 50 m/min KEY EQUIPMENT DELTA servo drives X axis support with double rails quick START- preparing machines for cutting under 1 minute planetary gears helical bevel bars in class 6 touch screen monitor with industrial computer remote control sectional extraction table with pneumatic cylinders anti-collision system CS- system that protects the torch from collision CLS system of central lubrication double basing of Y axis laser marker indicating the torch position SC system - safety system We offer other dimensions of tables.

Condition: refurbished (used), Year of construction: 1991, 1 piece overhauled industrial helical bevel gearbox from Flender TGL 21814 with backstop Maximum torque: 28,000 Nm Gear ratio: i= 1:20 Max. power: 105 kW Oil filling: 135 kg Speed: n1= 710 Speed: n2= 35 Maximum speed to transmission power (only with oil cooler) 710 rpm to 112 kW 950 rpm to 149 kW 1400 rpm to 220 kW Maximum speed to transmission power (without oil cooler) Psdpfxed Nqkro Aahjrc 710 rpm to 105 kW 950 rpm to 115 kW 1400 rpm to 130 kW Weight: 1560 kg Shaft diameter d1: 90 mm Shaft diameter d2: 160 mm Shaft height h1: 500 mm Total height h2: 925 mm Length of base: 1170 mm !! Gearbox has no oil cooler !!!

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Technical details: max. wheel diameter 2-45 mm gear width 250 mm max. module 1,5 mm min. module 0,5 mm Control Fanuc 18i-MB weight of the machine ca. 2,2 t dimensions of the machine ca. 2100 x 1440 x 1700 m Additional information: The combined CNC gear hobbing and worm milling machine KOEPFER MZ 120 is Podpfew Rmakjx Aahjrc characterized by its flexible usability and is used in the small module area. Just by swiveling the milling spindle from the horizontal to the vertical position and selecting the corresponding operating mode of the CNC control, the worm milling machine becomes a gear hobbing machine and vice versa. CNC control Fanuc 18i-MB (Dialog/ISO) CNC axes = X-axis plunge axis Z-axis longitudinal axis C-axis workpiece spindle B-axis tool spindle V-axis loader axis longitudinal A-axis swivel axis tool spindle head (included as an option) Y-axis shift axis (included as an option) With the following production programs: Worm milling Hobbing Worm hobbing Bevel gear and spur gear milling Bevel gear hobbing Milling cycles = straight, oblique, crowned toothing, radial, radial-axial, co- and counter-rotating milling, roughing, finishing, worm gears, straight-toothed bevel gears, face gearing (option only in the partial process) Worms [Equipment] Coolant tank 300 liters KF with LNS Turbo MS 250 Chip conveyor, built in 2021!!! Kraft and Bauer fire extinguishing system Spiral conveyor Machine documentation [Technical data] Workpieces: Workpiece diameter 2-45 mm Max. workpiece length 250 mm Tooth length 150 mm Max. module in steel= 1 mm (gear hobbing) 1.5 mm (worm milling) 0.5 mm (bevel gear hobbing) Tools: Cutter diameter= 16-32 mm (gear hobbing) 40-63 mm (worm milling) Machine: Max. setting angle of milling head= +/- 45° (gear hobbing) +/- 30° (worm milling) Shift travel= 34 mm (manual adjustment) 34 mm (CNC axis) Collet/retraction mandrel W 20 Max. speed of workpiece spindle 770 rpm. Milling spindle drive 0.55 kW Max. milling spindle speed 8000 rpm Axis drives = X-axis (plunging) / travel 80 mm via CNC Z-axis (longitudinal feed) / travel 190 mm via CNC C-axis (workpiece axis) via CNC Rapid traverse = X-axis 6000 mm/min. Z-axis 6000 mm/min. Hydraulic unit 0.37 kW

Year of construction: 2011, condition: excellent (used), functionality: fully functional, X-axis travel (longitudinal axis) 4300 mm Y-axis travel (transverse axis) 270 mm Predovi N H Tjpfx Aahec Z-axis travel (vertical axis) 300 mm Electrospindle 1 HSD - max 18000 rpm - power 5.5 kW Tool magazine capacity 8 Bevel gearbox for lateral machining Number of vices 4 Vices positioning: automatic Weight 1950 kg

Condition: new, machine/vehicle number: cd0062ee491e6794168ccb01a, empty load weight: 8 kg, maximum load weight: 26 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r 19,5, Further information Chassis semi-trailer In proven HANGLER welded construction made of high-quality steel with UP-welded side members tapered towards the front. Frame neck height 120 mm, with double center bar. Z-profile cross members punched through on the side member with floor panels (larger spacing) and with welded special side frame.2 kingpins to DIN 74080, replaceable, with grinding plate beveled to the front, made of high-quality sheet steel. EC front turning radius 2,040 mm. Sliding plate continuously welded from saddle plate to front plate *inside* 18 pairs of lashing eyes embedded in the outer frame, 2.5 tons each 8 pairs of lashing eyes embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side collision protection Plastic mudguards with splash protection mats Underride guard Impact protection at the rear Spare wheel holder for 1 e-wheel, with wheel mounting kit 3 Plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Aluminum ladder 3 300 mm, loose Pair of recessed stanchion pockets Piece of stanchions Storage compartment for plug-in slats on one side in FR left, below loading area Storage compartment for drop sides underneath the cargo bed, open, if technically possible Coil trough/inclined loading device Prsdpoi Riw Hefx Aahjc Coil trough 8,000 mm long with cover and rubber pad. Cover 35 mm. With inclined loading bars and supports suitable for FR 80/80/4, complete stanchions 80/80 incl. lower reinforcement supplied Hydraulic sloping loading device with 4 crossbars:Hydraulic supply via tractor unit by means of 2-pipe pump system (forward/return) with 2-fold Faster coupling mounted on bulkhead (hoses are connected to Faster coupling from below).Sloping loading bars (FR 180x100x8 mm) with integrated extension part can be locked in height. Multi-stage hydraulic cylinders, each beam with cardanic suspension Incl. outriggers - adjustable - with bolt safety device underneath the loading area5-fold control block for operating the sloping loading device and for folding device sliding roof.1 set of boiler floor holder with height-adjustable support bolts for different boiler floor diameters, incl. shelf.1 piece of stop protection for sloping plate - for securing to the front! Axles + suspension SAF disc brake axles Offset axle spacing mm Air suspension Brake system 2-line compressed air brake system Aluminum air reservoir Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Wabco, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift & lower valve + auto-reset function Vehicle - driving stability system Wheels and tires 435/50 R 19.5, manufacturer's choice Factory silver steel rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 additional LED work light(s) at the rear, switched via reversing light 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, detachable with plug 1 rotating beacon with holder, detachable Floor Screen printing plates approx. 3

Condition: used, Ceiling Laser LAP LASER CAD-PRO - used - Retrofit kit suitable for: e.g. HOLZ-HER ProMaster, Dynestic, Epicon, incl. LAP Ethernet gateway, 4 swivelling targets with bracket ----- Technical Specifications ----- Projection color: green, Supply voltage: 24 V DC, LAP connection cable: 25 m Prodpjxltvyofx Aahoc

Condition: ready for operation (used), Year of construction: 2013, Tools Max tool length 5760 mm Additional Equipment Joining Unit: 2 x 2.2 kW 200 Hz Gluing Unit: A12 Snipping Unit: Chamfer/Straight 2 x 0.35 kW Pneumatic Adjustment for Bevel/Straight Cross-Cuts Pneumatic 2-Point Adjustment for Cross-Cuts Pre-Milling Unit: 2 x 0.55 kW O degrees Pneumatic 2-Point Adjustment Multifunctional Shaping Unit: 2 x O, 4 kW Profile Scraper with Quick-Change Heads Pneumatic Adjustment Scraper Blade This BRANDT KDF 650 Highflex 1650 edgebander was manufactured in 2013. Ideal for precise edgebanding applications, it ensures reliable performance for woodworking professionals. Consider the opportunity to buy this BRANDT KDF 650 Highflex 1650 edgebander. Contact us for more information. Pedpfx Aaexfw A Rohsrc Application Types Edge Banding

Condition: used, Year of construction: 2014, CNC portal plasma cutting machine Manufacturer: Microstep Model: MG PrA 16501.25 S1200 (2 bridges) Year of manufacture: 2014 CNC control Working area: 16,500 mm x 2,500 mm + 1,200 mm trench 2 gantries Gantry 1: Plasma rotator with Kjellberg HiFocus 280i neo power source Predpfxowqg T Sj Aahsc Gantry 2: Oxy-fuel torch, gas type: acetylene The integrated 1,200 mm trench is additionally equipped with a pipe cutting device for pipe diameters 30 mm – 700 mm and a maximum length of 16,500 mm Donaldson DFPRO 16 Cyclopeel filter system for outdoor installation Software for - Nesting, - Bevel cutting, - Pipe processing

Condition: good (used), Year of construction: 2013, operating hours: 63,000 h, functionality: fully functional, We are offering 1 × KLINGELBERG used bevel gear grinding machine. Manufacturer: KLINGELNBERG AG Brand: KLINGELNBERG OERLIKON Model / Series: G 27 Year of manufacture: 2013 Type: Bevel Gear Grinding Machine Condition: Excellent / precise tolerances Applications: Spiral bevel gears, hypoid gears, planetary gear sets Industries: Transmission manufacturing, passenger car gearboxes, commercial vehicle and agricultural machinery gear units, forklift transmissions, special gearboxes, helicopter drives, etc. Pedjxg Ib Tepfx Aahjrc Technical specifications: - Max. gear diameter: 300 mm - Maximum module: 8 - Minimum module: 0.7 - CNC control: SIEMENS SINUMERIK 840 D solution line (latest software options!) - Min./max. pitch cone angle: −90 / +90° - Workpiece spindle bore: 127 mm - Grinding wheel diameter: 50 – 230 mm - Continuously variable spindle speed: 7,500 rpm - Workpiece spindle speed: 700 rpm - Total connected load: 146 kW - Machine weight: approx. 21 t - Machine dimensions: approx. 9.5 × 3.6 × 3.1 m - Integrated probe in grinding head - External spindle cooling - ELBARON integrated oil mist extraction system - HOFFMANN coolant filtration system for each machine The machine achieves outstanding tolerances and is ready for dismantling 14 days after conclusion of contract. Currently under power and available for demonstration. KLINGELNBERG inspection reports, demonstrating perfect results (and exact geometry), are available digitally and can be sent upon request. Please inquire for further details.

Condition: used, Year of construction: 1997, Beam planer 260 x 160 mm, rotating bevel unit on the upper spindle with two-axis control for the left and upper spindle max. working width: 260 mm max. working height: 160 mm Number of spindles: 6 pieces 1. Spindle: bottom spindle diameter 40 mm clamping length 270 mm speed 6000 rpm motor power 11.0 KW 2. Spindle: right spindle diameter 40 mm clamping length 170 mm speed 6000 rpm motor power 11.0 KW shared motor with left spindle 3. Spindle: left spindle diameter 40 mm clamping length 170 mm speed 6000 rpm 4. Spindle: top spindle diameter 40 mm clamping length 270 mm speed 6000 rpm motor power 11.0 KW Spindle: bottom Spindle diameter 40 mm Motor power 11.0 kW Speed 6000 rpm Clamping length 270 mm 6th spindle: top Chamfering unit Motor brakes: mechanical Up/down adjustment of the upper spindle: electric, selectable with/without feed Feed brake system: Yes Continuous feed speed up to: 3 - 23 m/min Feed roller pressure: pneumatic Feed power: 4.0 kW Feed drive: cardan Lubricant pump: manual Max. chip removal for joining: 10 mm Jointing bevel cutter on planer: Yes Driven rollers in the table: 1 Control type: PLC control Dimension display on spindle: mechanical numerical display Infeed rollers in front of planer: Yes Air cushion table: three-track Central lubrication point: Yes Description: short infeed table 1050 mm with interior light Predswwwkhopfx Aahoc Storage location: Nattheim

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Predpfx Aaoi Ri Rvjhjc Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, Year of construction: 2025, This is a state-of-the-art CNC machine dedicated to the industrial sector, used for cutting sheets and profiles, using a plasma torch. The machine is characterised, among other things, by a robust structure made of the highest quality steel and aluminium, a large cutting range, the possibility of cutting workpieces of any shape and low process costs. The high-end solutions used in production ensure reliable and safe operation. The cutting of the material is carried out in a short time, while maintaining the precision of the workpiece. In order to obtain the desired shape, it is only necessary to import the file into the software, so operation of this cutting machine is easy and intuitive. Our plasma cutting machines are primarily designed to process materials such as: - Black steel, - Stainless steel, CONSTRUCTION The frame of the plasma cutting machine is designed and manufactured from scratch in our factory. The high quality steel used for the machines is cut, then welded and machined. The entire frame, gantry and gantry arms have additional ribbing to achieve high rigidity and eliminate vibration and deformation. DRIVES Servo AC motors with high resolution and power have been used to drive our cutters, ensuring adequate acceleration and speed in each direction. These are highly dynamic and precise motors with feedback, guaranteeing zero defect by continuously controlling the operating parameters. The X and Y axes use classic and well-proven helical bars, which ensure long life and precision. FUEL Our plasma machines use components from the leading manufacturer PGCNC. The technologies used in the torch significantly increase productivity and cutting speed. HD technology provides better hole quality, increased piercing capacity and bevelling capabilities. This ensures high quality, repeatable cuts and maximises productivity with minimal running costs and reliability. Predsur R Erspfx Aahoc KNIFE TABLE The knife table is made with technology that is resistant to working at elevated temperatures. This allows us to work continuously without worrying about the occurrence of burn-outs that prevent the material from being evenly positioned on the work table. The positioning of the scissors can be easily changed according to the size of the workpieces to be burnt. The knife table is an excellent solution for cutting thicker materials. SOFTWARE The machine is equipped with Starfire 2D CAD/CAM software. Various functions are available to the user, including the ability to import finished designs in vector formats: .dxf, .plt, .ai, .eps. The programme ensures fast and precise development of cutting paths. PLASMA SOURCE The basic plasma equipment includes the 120A cutting system, which is characterized by high productivity and cutting quality and speed. AUTOMATIC LUBRICATION SYSTEM Plasma cutting machine equipment also includes an automatic lubrication system that minimizes machine maintenance. The central lubrication system is a simple and functional device used to supply grease to the places where machine and equipment components come into contact. - POWER 400V 50Hz - MAX SPEED 45 m/min - DOOR SHAPE 200-600 mm - TYPE OF WORKING TABLE Knife table - WORKING TABLE WEIGHT 500 kg/m2

Condition: excellent (used), TruTool PN 200 electric hand cutting machine Product features The new TruTool PN 200 vibrating shear is mainly used for cutting C-L-U sections, trapezoidal sheet metal, etc. components. The device with a short tool for processing sheet metal with a profile depth of up to 85 mm and for C-L-U sections. Also for corrugated sheet metal. Ideal for hard-to-reach places. The working direction can be adjusted 360° easily and without tools in 45-degree steps. Minimized set-up time Replacement of punch and yoke without interruption and without tools. Unmatched speed Fast and efficient, 2.1 meters per minute at 400 N/mm2 structural steel. Application: Trapezoidal sheet metal For cutting profiles up to 86 mm deep and 132.5 / 40 mm wide. For straight and diagonal cuts. Profiles For cutting C-L-U profiles. Corrugated sheet For cutting and slitting. For bevel cuts and internal and radial cuts. - MAXIMUM SHEET THICKNESSES: - MAXIMUM THICKNESS OF 400 N/MM² STEEL SHEET: 2 mm. - MAXIMUM THICKNESS OF STEEL 600 N/MM²: 1.5 mm Pedpfx Aaeuhm E Sjhorc - MAXIMUM THICKNESS OF STEEL SHEET 800 N/MM²: 1 mm - MAXIMUM THICKNESS OF SHEET METAL MADE OF ALUMINUM UP TO 250 N/MM²: 3 mm - RADIANCES: - LOWEST RADIUS: 50 mm - GENERAL INFORMATION: - OPERATING SPEED: 2.1 m/min. - NUMBER OF SHAKES AT NOMINAL LOAD: 1500 1/min. - INITIAL HOLE DIAMETER: 24 mm - RATED POWER CONSUMPTION: 550 W

Condition: new, The KF 200 is a robust Edge Beveling Machine from KNUTH, designed for efficient chamfering, deburring, and 45° beveling of steel, aluminum, and a variety of other materials. Its compact dimensions and simple operation make it particularly well-suited for large workpieces, including heavy metal sheets and long profiles. With tungsten alloy blades, the KF 200 offers superior tensile strength, hardness, and longevity, ensuring that demanding tasks are executed with precision. This machine operates at a speed of 3,500 revolutions per minute and can achieve chamfer heights ranging from 0 to 5 mm, making it versatile for different applications. Standard equipment includes a set of cutting inserts and an operator manual, allowing you to start working immediately. Whether you're preparing weld joints or performing intricate deburring tasks, the KF 200 stands out in the Edge Beveling Machines category. To enhance your production capabilities, request a quote today and elevate your sheet metal processing with KNUTH. Prjdeq Ny R Sspfx Aahoc

Condition: ready for operation (used), functionality: fully functional, workpiece length (max.): 7,500 mm, workpiece diameter (max.): 1,500 mm, No minimum price – guaranteed sale to the highest bidder! Auction of a complete sawmill including sharpening workshop! TECHNICAL DETAILS Prodjxgg Skjpfx Aahsc Max. log diameter: 1.5 m Max. log length: 7.5 m Automatic separator: RG SX Resaw: 1,300 RG Trimmer: NO/5 single-blade EQUIPMENT Primultini model 460 sharpening machine for bandsaw blades Primultini bandsaw blade beveling machine Vollmer sharpening machine Bandsaw blade end-welding device Additional sharpening machine Many saws

Condition: used, Year of construction: 2018, Opportunity to buy an outstanding ESAB plasma cutting machine built in 2018. Equipped with: ESAB DMX KIT automatic plasma beveler + iSeries 300 BEVEL PT 36 plasma torch with cutting and marking function Integrated water cooler and coolant Multi-point collision protection system Predpfxsxltg Se Aahec Carbon steel injection: 40 mm Maximum cutting thickness for carbon steel: 45 mm Stainless steel injection: 25 mm Maximum cutting thickness for stainless steel: 30 mm Aluminum injection: 25 mm Maximum cutting thickness for aluminum: 30 mm Availability: 02/2026 Viewing possible upon appointment. Multiple videos of the machine in operation available on request. Please note: The information on this page has been obtained to the best of our ability and belief. This information is provided in good faith, but its accuracy is not guaranteed. Accordingly, this information is not binding and does not constitute a contractual condition. We recommend that you check all essential details during an inspection of the machine. To save unnecessary travel costs for our customers, in most cases we recommend organizing a live video inspection. CNC Control: Esab Vision T5 Plasma source: iSeries 300 BEVEL Travel path length: 9000 mm Table width: 3400 mm Table length: 6500 mm Cutting width: 3000 mm Cutting length: 6000 mm Table height: 700 mm Exhaust section length: 515 mm Speed: up to 24000 mm/min Connected voltage: 230V Frequency: 50/60 Hz Power consumption: 2000 VA

Condition: good (used), Saw blade Ø 500 mm, cutting height approx. 160 mm, cutting width approx. 550 mm, saw motor 3 kW, upper saw section swivelling for bevel cuts with locking mechanism, cutting depth adjustment via spindle ratchet, with new 500 mm Ø CV saw blade Prjdpfovl E Niox Aahoc

Year of construction: 2025, condition: new, This is a state-of-the-art CNC machine dedicated to the industrial sector, used for cutting sheets and profiles, using a plasma torch. The machine is characterised, among other things, by a robust structure made of the highest quality steel and aluminium, a large cutting range, the possibility of cutting workpieces of any shape and low process costs. The high-end solutions used in production ensure reliable and safe operation. The cutting of the material is carried out in a short time, while maintaining the precision of the workpiece. In order to obtain the desired shape, it is only necessary to import the file into the software, so operation of this cutting machine is easy and intuitive. Our plasma cutting machines are primarily designed to process materials such as: - Black steel, - Stainless steel, CONSTRUCTION The frame of the plasma cutting machine is designed and manufactured from scratch in our factory. The high quality steel used for the machines is cut, then welded and machined. The entire frame, gantry and gantry arms have additional ribbing to achieve high rigidity and eliminate vibration and deformation. DRIVES Servo AC motors with high resolution and power have been used to drive our cutters, ensuring adequate acceleration and speed in each direction. These are highly dynamic and precise motors with feedback, guaranteeing zero defect by continuously controlling the operating parameters. The X and Y axes use classic and well-proven helical bars, which ensure long life and precision. FUEL Our plasma machines use components from the leading manufacturer PGCNC. The technologies used in the torch significantly increase productivity and cutting speed. HD technology provides better hole quality, increased piercing capacity and bevelling capabilities. This ensures high quality, repeatable cuts and maximises productivity with minimal running costs and reliability. Prodpeiqn Uujfx Aahoc KNIFE TABLE The knife table is made with technology that is resistant to working at elevated temperatures. This allows us to work continuously without worrying about the occurrence of burn-outs that prevent the material from being evenly positioned on the work table. The positioning of the scissors can be easily changed according to the size of the workpieces to be burnt. The knife table is an excellent solution for cutting thicker materials. SOFTWARE The machine is equipped with Starfire 2D CAD/CAM software. Various functions are available to the user, including the ability to import finished designs in vector formats: .dxf, .plt, .ai, .eps. The programme ensures fast and precise development of cutting paths. PLASMA SOURCE The basic plasma equipment includes the 120A cutting system, which is characterized by high productivity and cutting quality and speed. AUTOMATIC LUBRICATION SYSTEM Plasma cutting machine equipment also includes an automatic lubrication system that minimizes machine maintenance. The central lubrication system is a simple and functional device used to supply grease to the places where machine and equipment components come into contact. - POWER 400V 50Hz - MAX SPEED 45 m/min - DOOR SHAPE 200-600 mm - TYPE OF WORKING TABLE Knife table - WORKING TABLE WEIGHT 500 kg/m2

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, Brand: SCM Model: OLIMPIC K 500 T/ER-2 - CE Automatic edge banding machine with edge sanding unit for processing edges made of wood, veneer, PVC, melamine, ABS – suitable for furniture manufacturing, joinery, custom fittings, panels, kitchen and bathroom furniture, and various other products. Technical data: Min./max. panel height: 8–60 mm Panel height with rounding unit: 10–45 mm Edge thickness: 0.4–8 mm Edge thickness in roll: 0.4–3 mm Minimum panel width: 55 mm Feed speed: 11 m/min Pressure beam with motorized vertical adjustment Prjdpfx Aexnvr Asahoc Panel support arm Sound-insulated safety cabin Fluid inlets Configuration: Anti-adhesive application unit with two nozzles – two separate tanks for anti-adhesive fluid Pre-milling unit with two high-frequency motors – diamond tools H64 mm – diameter 100 mm, F 30, h 65 – copying kit included VC 560 gluing unit for applying edging to panels up to 60 mm – glue pot capacity: 1.5 kg – interchangeable glue pot End cutting unit with two independent motors, each 0.35 kW at 12,000 rpm – motor tilt from 0° to 15° – 2 saw blades, 115 mm diameter – face copiers Tilting trimming/bevelling unit for trimming excess edging top and bottom – 2 motors of 0.55 kW each – 12,000 rpm – tilt from 0° to 25° – 2-position pneumatic quick-change kit for processing thin or radius edges Corner rounding unit with two motors on precision guides – enables rounding and trimming of thin and thick edges – 2 motors of 0.55 kW each – 12,000 rpm Edge scraping unit for optimal finishing of ABS/PVC edging with rotating tracing guides, extraction hood, and trimming waste cassette Glue scraping unit – removes glue residue from the lower and upper panel surfaces Brushing unit for cleaning and polishing plastic edges – motor 0.25 kW – brush diameter 150 mm Compressed air: 7 bar Overall dimensions: 5500 x 1150 x 1550 (H) mm Weight: 1,780 kg

Condition: used, Year of construction: 2020, Used machine Year of manufacture: 2020 Equipment and technical data: Working dimensions Workpiece thickness: 8–60 mm Workpiece width: from 70 mm Edge height: up to 8 mm Edge thickness for roll material: up to 3 mm Feed Speed adjustable from 8 to 14 m/min, stepless regulation Gluing technology Glue system for granulate Glue pot located above the feed Interchangeable pot HOMAG QA 65 N Designed for EVA and PUR processing Quick-change function Units Jointing milling unit Pre-heating zone Pressure station, NC-controlled Prodpfx Aexizulsahoc Front and end trimming with two motors Station for flush, radius, and bevel processing Corner rounding unit with two motors Scraper blades: profile and flat scraper Buffing unit Additional equipment and operator features Integrated spraying device Air cushion table for workpiece support PU pressure rollers Mechanical infeed barrier HOMAG powerTouch operator interface Right-hand machine version CE-compliant Dimensions: approx. 6,060 x 950 x 1,150 mm Weight: approx. 2,200 kg Availability: approx. December 2025 Location: North Rhine-Westphalia (NRW)

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, edge thickness (max.): 10 mm, overall weight: 1,980 kg, height adjustment type: electric, Biesse Type Akron 440 Year of manufacture: 2007 Noise rating according to manufacturer: 88 dB (A) Rated power: 13 kW Extraction capacity according to AUVA: 565 m³/h Technical specifications: - Edge thickness from 0.4 - 10 mm Pjdpfx Aaowahhpjhjrc - Feed speed 12 m/min - Max. edge banding height 13 - 60 mm - Release agent - Jointing unit - Edge magazine - Preparation for PUR adhesive - Trimming unit, pivoting 0-15° - Pivoting bevel/radius unit RS-501 - Profile trimming unit - Radius scraper RBK 502 - Flat scraper RCC 701 - Buffing unit SP 501 - Electric height adjustment - Total connected load 13 kW - Machine length 4200 mm

Condition: new, empty load weight: 2,980 kg, maximum load weight: 7,520 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 6,280 mm, loading space width: 2,480 mm, suspension: steel, tire size: 245 / 70 R 17,5, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, each ramp approx. 2,700 mm long x 560 mm wide, ramps with gratings, loading height: 840 mm, 12 lashing eyes each 2.5 t, 8 x lashing eyes each 6 t, steel drop sides, foldable and removable, wooden planks 50 mm, loading area rear beveled, loading area width inside 2.480 mm, rear stanchion removable, front for through-loading, , Also available in 5,300 mm loading area length! , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Prsdoxghumjpfx Aahsc

Condition: new, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 6,700 mm, loading space width: 2,480 mm, suspension: air, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, 400 mm side walls, steel side walls HOT-DIP GALVANIZED, with central stake on the side, plug-in, chassis: hot-dip galvanized, wooden floor, 14 lashing eyes in the outer frame, bevelled at the rear, 2 x ramps each 3,000 mm long x 725 mm wide, ramps with spring lifting mechanism, ramps with gratings also available in wood!, Loading height: 880 mm, , Also available in loading area length 7.20 m, available for immediate delivery., , Rental price from 580 euros, , --  Subject to printing errors, mistakes and changes, Sample images --, More data at: !, More details: ! Pjdoxghuyopfx Aahsrc