Used Centricator for sale (52)

Condition: good (used), Year of construction: 2020, machine/vehicle number: 164390-0000-Z2724, Offer 24059 Technical data: - Jaw design stepped jaws Rcedpforwmkajx Abpsf - Jaw width 125 mm - Jaw height 40 mm - Clamping width 1 0 - 216 mm - Clamping width 2 97 - 312 mm - Clamping force 40 kN - Total height 140 mm - Weight 33 kg - Min. Space requirement L 463 x W 126 x H 145 mm

Condition: new, Amada/promecam style Centrical 1V press brake dies Rcjdpfoin I Hrox Abpef

Condition: new, Amada/promecam style Centrical 1V press brake dies for Trumpf Rcodpfeiqf R Ijx Abpef

Condition: new, Amada/promecam style Centrical 1V press brake dies for Lvd Rcodpfxjiqgaae Abpjf

Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Rjdpjzg N E Hsfx Abpecf Cut...

Year of construction: 2006, condition: excellent (used), Transport and automation system for motor housings with control system Technical parameters of motor housing Inner diameter: 66 mm, 70 mm, 74.2 mm Wall thickness: 2 mm Length: 87.8 mm – 135 mm Material: Steel, painted Technical parameters of grinding machine - Two-belt grinding machine, type M2-120, manufacturer Weber - Includes continuous prism conveyor with adjustable speed via frequency converter System output: max. 52 pieces per minute Functional description: The motor housings are manually removed from the grid box by one person and placed on a buffer table in a defined position. A row pusher moves the foremost row onto a permanent magnetic articulated belt conveyor. Rcsdpfx Aszww Ecjbpjf The motor housings are automatically transported and transferred to a permanent magnetic combination conveyor. After a 90° deflection, the housings are buffered in a roller track. One housing is released at a time and fed to a prism conveyor. The combination conveyor is axially adjustable, so that a centric feed to the prisms is ensured depending on the housing length. After the grinding process, the motor housings are transferred to another permanent magnetic combination conveyor. After a 90° deflection, the housings are brought into a stationary position and guided onto a permanent magnetic articulated belt conveyor. With stamping number control system Syscona For secure and reliable detection of stamping numbers in metal tubes. Detection station with high-resolution CCD black and white camera with scan sensor. With control system Syscona For detection of bumps in tubes according to a pattern. HighVision HV video camera system Defective motor housings are identified and transmitted accordingly to the rejection device. A swivel cylinder directs the housings onto a parallel articulated belt conveyor, which transfers them to a buffer table. DISMANTLING by customer!

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, workpiece weight (max.): 30 kg, input voltage: 400 V, rotor diameter: 600 mm, year of last overhaul: 2023, power: 1.1 kW (1.50 HP), Balancing machine upgraded in 2009. 1 Machine base, welded construction 1 Balancing unit Vertical, single plane, permanently calibrated, 1 special spindle with centric flange 1 piezo-electric vibration sensor 1 3-phase drive motor of 1.5 kW, driven by a belt 1 Protractor disk 300 mm diameter, with 360 °, mounted on the spindle 1 Safety guard For diameters up to 600 mm and heights of 420 mm 1 SCHENCK CAB 803 measuring device - With direct data entry system via touch screen - Industrial PC with active TFT color monitor - Visualization of results via vector meters - Network capability Rcjdpeq Umcrjfx Abpef - Polish dialogue - Modular, easy-to-use system design - Optimized signal processing system via digital Schenck MMD filter - Intelligent, self-diagnosing measurement electronics system - Operation using standard Windows routines - Programs for: - Straight compensation, keyway, compensation index - Tolerance calculation according to ISO 1940 - Log report in PDF format Balancing speeds from 0 to 720 RPM - Smooth Max residual unbalance 5 - 10 gmm (DIN 1319)

Condition: good (used), functionality: fully functional, tool type: SK 40, SK40 Cutting Wheel Holder 4 pcs tool holders / cutting wheel holders / backing wheel holders for cutting wheels / backing wheels / backing blades, size SK 40, including the tool changing device / tool holding device. Redeikvwqspfx Abpecf In good, used condition. 1 x Ø 31.75 x 120 for disc cutting wheel 1 x Ø 44.45 x 84.5 for disc cutting wheel / bell cutting wheel 1 x Ø 44.45 x 84.5 for disc cutting wheel / bell cutting wheel, special holder with centric mounting bore Ø9.9 for additional tool clamping device. 1 x MK2 for shank cutting wheel Price negotiable Our asking price is €1,190 for the set, net, ex works, plus packaging costs. All technical specifications are subject to printing errors and changes. We only sell to countries within the European Community.

Condition: new, Factory-new, electrically heated stainless steel mixing tank Article number: EBB150RWAD Volume: 152L Dimensions approx.: Ø 660mm x cylindrical height 625mm Overall height: 910mm Material: 1.4301 stainless steel V2A Surface: Matte finish inside and out Welds ground smooth Operating temperature max.: 110°C Operating pressure tank: ATM -Vertical design on rollers -Top: Central cross member for the agitator with two hinged lid halves -Bottom: Flat bottom with side outlet DN50 DIN11851 and disc valve -Agitator flange on the top -2x handle for pushing -1x nameplate Heating system: Indirect heating Double jacket around the tank with glycerine filling as the heat transfer medium. Heating is carried out by an electric heating element in the double jacket. Power: 9KW Operating voltage: 3PH 400V Incl. supply line 16A CEE plug Centric agitator: Slow-speed anchor agitator with wall scrapers Type: SRTGMK/0.37-9.5 Manufacturer: Schwarzer Rührtechnik GmbH Power: 0.37KW Speed: 0-9.5 RPM Operating voltage: 1PH 230V Material in contact with product: 1.4301 stainless steel -Gearbox and motor in the latest aluminum technology, manufacturer Getriebebau NORD -Gearbox with food-grade approved oil filling "Klüber" -Solid agitator shaft attached to the agitator motor with a sleeve coupling, detachable -Agitator shaft balanced for smooth running in the speed range -1 piece of large anchor agitator in the tank, welds ground smooth, arranged close to the wall -2 Teflon wall scrapers in the cylindrical area, one at the bottom -Stainless steel flange with shaft seal, EPDM Rcodjh Hxxfspfx Abpof Speed control: Compact frequency inverter on the agitator motor with on/off switch and potentiometer Control: 5m cable and RCD socket switch, undervoltage release Eccentric agitator: Speed-adjustable dissolver agitator Type: SRTMKD/1.1-1500-Vari Manufacturer: Schwarzer Rührtechnik GmbH Power: 1.1KW Speed: 0-1690 RPM Operating voltage: 3PH 400V Material in contact with product: 1.4301 stainless steel -Motor in the latest aluminum technology, manufacturer Getriebebau NORD -Solid agitator shaft attached to the agitator motor with a sleeve coupling, detachable -Agitator shaft balanced for smooth running in the speed range -1 piece of dissolver disc Ø 125mm screwed onto the end of the agitator shaft, seal O-ring, EPDM -Stainless steel flange with V-ring seal, EPDM -Stainless steel spacers for motor mounting Speed control: Frequency inverter mounted on the motor, manufacturer Getriebebau NORD. On/off switch, potentiometer, phase inverter Control: CEE plug switch on the tank with undervoltage release and phase inverter, emergency stop

Condition: used, functionality: fully functional, machine/vehicle number: 106341-11, Year of construction: 2005, overall weight: 8,000 kg, total height: 2,700 mm, total length: 5,660 mm, total width: 3,956 mm, The drilling method of the deep hole drilling machine is single-lip drill deep hole drilling. Drilling Unit Information: - Number of spindles: 1 - Infinitely variable spindle speed: 300 – 8000 rpm - Spindle drive power: 7.5 kW - Max. drilling depth: 800 mm - Drilling diameter min/max: 3 – 25 mm based on ST 60 - Max. twist drilling: 25 mm - Max. thread tapping: M24x3 - Milling material removal rate: 150 cm³/min Travel Paths: - X-axis travel: 800 mm - Y-axis travel: 400 mm - Z-axis travel: 630 mm - W-axis travel: 800 mm Travel Speed: - X-axis speed: 15,000 mm/min - Y-axis speed: 15,000 mm/min - Z-axis speed: 15,000 mm/min - W-axis speed: 15,000 mm/min Fluid Information: - Coolant supply: deep hole drilling oil - Tank capacity: 800 liters - 1x scraper belt chip conveyor - 1x hydraulic unit and pneumatic system/equipment - 1x submersible pump: Pumping capacity: 200 l/min - 1x low pressure pump: Pumping capacity: 100 l/min Pump drive: 1.7 kW - 1x compact belt filter: Filtration capacity: 120 l/min for processing steel/non-ferrous metals - 1x radial piston pump with remote adjustment: Pumping capacity: 2 – 94 l/min Pump drive: 7.5 kW Spindle Unit: - Cartridge spindle design with drive housing and spindle drive with gearbox. Spindle bearing with precision angular contact ball bearings and lifetime grease lubrication. Milling and Drilling Spindle Unit: - For conventional machining - Spindle head with HSK 50 tool holder Drill Bush Holder: - Design as 2-position turret with electric swivel mechanism - Locating position via Hirth coupling - Turret head with fixtures for: Guide bushes for deep hole drilling Milling and drilling spindle unit for conventional machining Pickup Tool Changer: - For conventional tools and drill bushings - Disc magazine design with 20 stations including feed stroke Automatic Tool Changer for Deep Hole Drilling Tools: - Fixed ELB column magazine for at least 5 tools including automatic tool clamping for HSK holders Clamping Table with W-Axis and NC Rotary Table: - Length/width: 800 x 600 mm - Positioning accuracy: B-axis +/- 30" - Centric payload: 1,500 daN Rcodow E H E Rspfx Abpof Workpiece Clamping Device: - 1x tailstock with manual clamping movement - 1x NC dividing unit (A-axis) with manually operated two-jaw chuck for workpiece clamping - 1x base plate for mounting and clamping drill bushings + supporting prisms Electrical Equipment Information: - 1x CNC control Sinumerik 840D (digital complete system), including PLC S7-300 Connection Data: - Operating voltage: 3AC 400V ±10% – Frequency: 50 Hz - Control voltage: 24 V DC - Total connected load: 25 kW

Condition: ready for operation (used), Year of construction: 1990, functionality: fully functional, CNC Table Type Boring and Milling Machine - Horizontal | Brand: UNION Type: BFT 105 | Year of construction: 1990 Machining operations: Boring, reaming, deep boring, precision boring, reaming, countersinking, tapping, milling, circular milling, thread milling. The machine can be inspected under power by prior appointment. Condition: Very well-maintained, second-hand / operating condition. TECHNICAL SPECIFICATIONS: - Travels: - X-axis (table transverse movement): 1.750 mm - Y-axis (headstock vertical movement): 1.250 mm - Z-axis (table longitudinal movement): 1.175 mm - B-axis (table positioning): 360° - W-axis (boring spindle axial adjustment): 450 mm Clamping table: - Clamping surface: 1.250 x 1.400 mm - Maximum workpiece weight with centric clamping: 4 tons - T-slot spacing: 125 mm - T-slot width: 22H7 mm - Centring bore: 250 mm Boring spindle: - Diameter: 105 mm - Axial adjustment: NC-controlled - Tool holder: * with tapered shank: A 50 TGL 7837 * with steep taper: A 50 DIN 2080 * with clamping bolts: UNION 95-2805 (A 50 TGL 42620) DIN 69872-28 Speed ranges: - 3 continuously variable ranges: 4 – 2.500 rpm - Drive power: 23,7 kW - Max. spindle torque: 2.500 Nm Feed rates: Continuously variable feed range - X, Y, Z axes: 1 – 5.000 mm/min - Rapid traverse, X, Y, Z-axes: 10.000 mm/min W-axis: 5.000 mm/min B-axis: 3,2 rpm - Max. feed force: X and Y-axes: 16.000 N Z-axis: 25.000 N Specifications: - Total connected load: 50 kW/130 A Rjdpfxozlal Io Abpjcf - Voltage/frequency: 380 V/50 Hz - Machine weight (approx.): 17 tons - Dimensions: 6.560 x 4.370 x 3.450 mm EQUIPMENT: - 5-axis path control: Heidenhain TNC 355 - Swivelling control panel with central control station - Electronic handwheel - Other comprehensive ranges of accessories, such as tool holders, drill bits, milling cutters, and tool trolleys and cabinets ... - Comprehensive documentation available (foundation plan, circuit diagrams, hydraulic documentation, operating instructions and spare parts lists, programming lists) No guarantee is given for the completeness and accuracy of the technical information and equipment. - Subject to prior sale -

Condition: used, Two-jaw chuck, 2 jaw chucks, vice, face plate -Chuck size: Ø 250 mm Redpfodu Uffox Abpecf -centrically exciting: -Weight: 35 kg

Condition: used, Machine vise, sturdy vise, drill vise -Jaw width: 160 x 45 mm -Clamping depth: max. 260 mm -Tension: centric Rcsdpfx Abefxg N Ujpjf -Dimensions: 590/200/H125 mm -Weight: 36 kg

Condition: used, Machine vice, stable vice, drill vice -Back width: 110 x 30 mm -Tension depth: max 132 mm -Tension: centric Rcodsd Aghaspfx Abpof -Dimensions: 345/135/H95 mm -Weight: 11.7 kg

Condition: used, Two-jaw chuck, 2 jaw chucks, vice, face plate -centric: exciting Redpfechyydex Abpscf -Chuck size: Ø 242 mm -Rezess: Ø 190 mm -Hole circle: Ø 215 mm -Weight: 26.4 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate Rjdpfx Ajb A Rfcjbpecf -Mouth size: Ø 160 mm -exciting: centric -Replaceable jaws: soft -Cone mounting: Ø 105 mm -Bolt circle: Ø 135 mm -Weight: 18 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate -exciting: centric -Mouth size: Ø 200 mm Rcodpfx Aeb A R Hvsbpsf -Weight: 19 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate -Mouth size: Ø 125 mm Rcsdpfx Aeb A Rdljbpof -exciting: centric -Replaceable jaws: soft -Weight: 6 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate -Mouth size: Ø 125 mm -exciting: centric Rcjdpfjb A Rdqox Abpjf -Replaceable jaws: soft -Cone mounting: Ø 82 mm -Bolt circle: Ø 105 mm -Weight: 14 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate Rodpfx Abob A Rfmjpscf -Mouth size: Ø 125 mm -exciting: centric -without interchangeable jaws: without -Weight: 4 kg

Condition: good (used), Machine vice, sturdy vice, drill press vice Redpefxg Nfjfx Abpocf -Jaw width: 215 x 40 mm -Clamping depth: max. 240 mm -Tension: centric -Dimensions: 460/280/H135 mm -Weight: 35 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate -Clamping angle: 200 x 200 mm -centrically exciting -Mouth size: Ø 200 mm Rcedpfxsb A Ig Aj Abpef -Weight: 30 kg

Condition: good (used), Two-jaw chuck, 2-jaw chuck, vise, faceplate -Mouth size: Ø 250 mm -exciting: centric -Replaceable jaws: soft Rcjdpfxjb A Rd Eo Abpof -Weight: 22 kg

Condition: good (used), Machine vice, sturdy vice, drill press vice Redjd Ehfzjpfx Abpjcf -Jaw width: 150 x 60 mm -Clamping depth: max. 285 mm -centric clamping -Dimensions: 620/275/H135 mm -Weight: 41 kg

Condition: excellent (used), PLASTIC PIPE CUTTER ROCUT 110 BY ROTHENBERGER 55035 ROTHENBERGER pipe cutter 50-110mm Manufacturer code 55035 TECHNICAL DATA pipe diameters - 50, 75, 110mm pipe chamfer angle - 15° . PRODUCT DESCRIPTION Tool designed for cutting and chamfering thin- and thick-walled PVC, PE, PE-X and PVDF pipes, as well as attenuated sewer pipes. Simultaneous chamfering around the entire circumference of the pipe through a steel cutting mandrel with an automatic kicker. Centric and secure clamping on the pipe taking into account the dimensional tolerance thanks to infinitely adjustable jaw pressure with spring compensation. Rcjdpjvb Ik Isfx Abpof