Used Cnc Turn Mill Centre for sale (22,588)

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit Ppodpfxjyaqgyo Adbel FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026.

Condition: good (used), Year of construction: 2008, operating hours: 72,899 h, functionality: fully functional, machine/vehicle number: 07510001241, turning length: 1,185 mm, turning diameter: 640 mm, spindle speed (max.): 12,000 rpm, workpiece weight (max.): 150 kg, total height: 3,040 mm, total length: 7,800 mm, total width: 4,100 mm, overall weight: 16,500 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, DMG GILDEMEISTER GMX 250 LINEAR CNC Turning and Milling Center - Recorded spindle hours: 39,361 - Swing diameter: 640 mm - Counter spindle turning diameter: 400 mm - Spindle distance: 1,500 mm - X1 axis travel: 550 mm - Y1 axis travel: 180 mm - Z1 axis travel: 1,185 mm - B1 axis travel: 240° Pedpfoyaqczjx Adbjpl - X2 axis travel: 180 mm - Z2 axis travel: 1,050 mm - Z3 axis travel: 1,150 mm - Spindle speed range: 3,200/4,000 rpm - Rapid traverse rate, Slide 1 (X/Y/Z): 40/24/70 m/min - Rapid traverse rate, Slide 2 (X/Z): 24/36 m/min - Rapid traverse rate, Slide 3 (Z): 36 m/min - Tool holder: HSK 63 - Spindle speed: 12,000 rpm - Number of tool stations in chain magazine: 40 stations - Incl. tool holders mounted on the turret - Incl. bar loader, manufacturer: COCCHE GIOVANNI, type: CNC-DB 110, year of manufacture: 2008, serial number: CNCDB-08.306, weight: 1,500 kg Note: The machine has the following defects: - The hydraulic unit is faulty – it needs to be repaired - The Q2 axis (milling spindle tool changer) fails frequently - X2 axis (guideways) moves slightly askew - The linear guides and drives show wear commensurate with age Attention: A vehicle with 3,000 mm transport width is required for transport! FCA D-58256 Ennepetal, loaded onto truck at a mutually agreed date at the end of February 2026.

Condition: ready for operation (used), Year of construction: 2018, Control Unit Brand MAZATROL Model SMOOTH X Main Drive Number of spindles 2 Ppjdpfx Asx Stk Tedbol Spindle speed range 1 - 3300 rpm Spindle bore ø112 mm (ø4.41 inches) Number of axis 5 Movement X-Axis Movement 615 mm X-Axis Rapid Traverse 50 m/min Y-Axis Movement 260 mm Y-Axis Rapid Traverse 40 m/min Z-Axis Movement 2563 mm Z-Axis Rapid Traverse 40 m/min W-Axis Rapid Traverse 30 m/min Tools Number of index 72 Max weight 12 kg Max tool diameter 90 mm Type of tool holder HSK-A63 (T63) This 5-axis Mazak Integrex i-400S-2500U was manufactured in 2018, featuring Mazatrol SMOOTH X Control and a Hydrafeed MSV110 Barfeed. It offers a maximum machining diameter of ø658 mm and a length of 2,497 mm. Equipped with a milling spindle speed of 12,000 rpm and a tool storage capacity of 72 tools, this turn-mill centre is ideal for complex machining tasks. If you are looking to get high-quality turning and milling capabilities, consider the Mazak Integrex i-400S-2500U machine we have for sale. Contact us for more information. Application Types Turning

Condition: used, Year of construction: 2007, turning diameter 42 / 140 mm turning length 170 mm control Mitsubishi Meldas turning speeds 80-8.000 U/min Ppedpsvyli Ejfx Adbjl c-axis 0,001° turret (x-stations) 2x 12 (VDI 20) angetrieben turning speeds 45-4.500 U/min spindle 1 kW gripping station 42 mm turning speeds 60-6.000 U/min c-axis 0,001° number of controlled axis 8 collet unit 48 DIN 6343 . Number of working hours 10769 h chip conveyor ja/yes Bj. 2018 total power requirement 7,5 / 11 kW weight of the machine ca. 3,3 t dimensions of the machine ca. 2,4 x 1,6 x 2,2 m CNC turning and milling machine CITIZEN BOLEY BE 42, year 2007 Simultaneous working with 7 axes on main and pick-up spindle very good condition, operating hours 21.999h (September 2024) Accessories: # Various tool holders: 5x axiale driven tool holder # collet chuck for collets type 173E # additional coolant cooler # Knoll chip conveyor, year of construction 2018 The Boley BE 42 is without barloader. Loading magazine interface has been fitted. Complete battery exchange on 22.12.2025

Condition: like new (used), Year of construction: 2023, operating hours: 3,751 h, functionality: fully functional, turning length: 700 mm, turning diameter: 356 mm, spindle speed (min.): 6,000 rpm, spindle bore: 81 mm, travel distance X-axis: 260 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 795 mm, DMG MORI NLX2500/700 universal lathe with Y-axis, bar feeder, and driven tools. Main and sub spindle. Spindle bore diameter: 81 mm. INCLUDING tool package (purchase price €64,000 / see attachment). Psdsx Sp Izepfx Adbspl

Condition: like new (used), Year of construction: 2021, functionality: fully functional, This multi-axis CNC lathe, CMZ TTL-66-66-T1Y-T2Y, was manufactured in 2021. It features a maximum bar capacity of 66 mm (both spindles), a turning diameter of up to 220 mm, and a main spindle power output of 35.5 kW. The machine is equipped with two high-performance spindles with a 66 mm bar passage, two turrets with 12/24 tool stations, driven tools with 14 kW and 12,000 rpm, and Y-axis capability on both the upper and lower turrets. It includes a 35-bar high-pressure coolant system, complete with a filtration system and an additional tank. For more information about this lathe, please refer to the attached brochure or contact us directly. Equipment includes: - LPS for left spindle - Reduction tube for left spindle - Hainbuch AXFIX 65 collet chuck (standard) 2703/0008 for left spindle - Hainbuch AXFIX 65 collet chuck (standard) 2703/0008 for right spindle - Tool presetting device - Side-mounted chip conveyor (standard version) - Upper tool turret (T1) high-pressure coolant pump with three programmable pressure levels (35, 15 & 6 bar), including 75µm filter - Lower tool turret (T2) high-pressure coolant pump with three programmable pressure levels (35, 15 & 6 bar), including 75µm filter - Coolant wash nozzle - TA/06000/10 8,000W coolant chiller unit - Machine status indicator light - Tool life management system - Tool load monitoring - Programmable automatic parts catcher (pneumatic) - The workpiece extractor is equipped with a pneumatic gripper for automatic opening and closing to retrieve finished parts Pedpfx Adexmhdnobepl - Pneumatic ejector for the sub-spindle with 100 mm adjustable stroke. End position detection via sensor - Coolant supply through right spindle - Interface for bar feeder (unimag) - Preparation for extraction unit, connection flange Ø100 The machine comes complete with a chip conveyor, coolant unit, and tool package. It is available for immediate inspection under power, and available at short notice. Single-shift operated. Further information available on request.

Condition: reconditioned (used), Year of construction: 2005, Cycle-controlled lathe GILDEMEISTER NEF 520 With MANUAL PLUS 4110 control Year of manufacture: 2005 Spindle bore: 70 mm Center distance: 1000 mm Pedpfx Aouda Tnjdbjpl O rotation over bed: 500 mm O rotation over cross slide: 290 mm Center height: 250 mm Speed range: 10 - 3050 rpm infinitely variable With the following accessories: Sliding guard with interior lighting 8-station Sauter VDI 30 turret with driven tools 10 pcs. VDI 30 tool holders 2 pcs. driven tools VDI 30 Coolant device 3 jaw chucks SCHUNK ROTA 0 250 mm ICP contour programming Tailstock with extendable drilling quill Chip tray Operating instructions

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, turning length: 1,000 mm, turning diameter: 90 mm, spindle motor power: 40,000 W, spindle speed (max.): 4,000 rpm, torque: 190 Nm, total height: 2,550 mm, total length: 4,325 mm, total width: 2,350 mm, bar diameter (max.): 90 mm, overall weight: 14,000 kg, Equipment: documentation/manual, rotational speed infinitely variable, Main and sub spindle C-axis VDI 30 turret (Turret II) Drill breakage control High-pressure system Cooling unit Eco-Fluid coolant lubrication system KNOLL chip conveyor Irco Breuning short bar loader Psdpfx Asx T A Drodbspl

Condition: excellent (used), Year of construction: 2003, operating hours: 8,000 h, functionality: fully functional, machine/vehicle number: A8A R19 52, turning length: 225 mm, turning diameter over cross slide: 250 mm, turning diameter: 80 mm, spindle motor power: 4,400 W, spindle speed (min.): 300 rpm, spindle speed (max.): 6,300 rpm, spindle bore: 25 mm, travel distance X-axis: 100 mm, travel distance Z-axis: 300 mm, bar diameter (max.): 25 mm, quill stroke: 50 mm, Equipment: documentation/manual, Additional info : 12-station tool turret for VDI16 quick change tools bi-directional logic for driven tools Ppsdpfx Adjxvb Thebol

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, We offer you: Manufacturer: DMG Gildemeister Model: GMX 250 linear Year of manufacture: 2006 Control: Siemens 840 D powerline Technical Data: Max. turning diameter: 640 mm Turning length: 1,185 mm Draw tube inner diameter: 67 mm Travels: x1-axis: 550 mm y-axis: +/- 90 mm z1-axis: 1,185 mm b-axis: +/- 120° x2-axis: 180 mm z2-axis: 1,050 mm Main spindle: Max. speed: 5,000 rpm Drive power: 21/28 kW Counter spindle: Max. speed: 5,000 rpm Drive power: 21/28 kW Milling spindle: Speed range: 0 – 12,000 rpm Indexing: 1° Tool holder: HSK63A Number of tool pockets: 46 positions Turret: Number of tool holders: 12 positions Holder: 40 mm Hollow clamping device: Ø 67 mm Operating hours: approx. 92,100 h Spindle hours: approx. 47,800 h Technical features and accessories: - Main and counter spindles ISM 76 - C-axis and spindle brake, hydraulic - B-axis interpolating and with hydraulic clamping - Tool magazine with 4 additional loading stations Podpfx Adsyfmibebepl - Absolute, direct measuring systems on all linear axes - Coolant tank 600 l with lifting pump and level regulator - Coolant filtration with belt filter, coolant pump 8 bar, 20 l/min - Chip conveyor - Preparation for work area extraction - USB and Ethernet interfaces - Tool monitoring system, manufacturer Artis, type CTM - Star turret with driven tools, including direct measuring systems - Counter spindle with partial hollow clamping device, C-axis and spindle brake (hydraulic), holding brake and direct measuring system - Automatic sliding safety door - Coolant spray gun - Electrical cabinet lighting and socket outlet - Signal lamp, 4 colors - Tailstock function for the counter spindle - 2x three-jaw power chucks, manufacturer Forkardt 30QLC 250-72 - Turret-mounted steady rest, range 8 – 101 mm Accessories, tools, and clamping devices shown only included if specified in the additional information. Subject to changes and errors in technical data and specifications, as well as prior sale!

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, We offer you the following: Manufacturer: DMG Mori Model: NTX 2000/1500 2nd Gen Year of manufacture: 2020 Control: Celos Fanuc F31iB5, Mapps 4 Technical Data: Maximum turning diameter: 670 mm Turning length: 1,538 mm Bar capacity: max. 65 mm Travel axes: X1 axis: 675 mm Y axis: ±150 mm Z1 axis: 1,562 + 164 mm B axis: ±120° Psdpfx Aeyfl N Tjdbspl A axis: 1,542 mm X2 axis: 200 mm Y2 axis: ±40 mm Z2 axis: 1,542 mm Main spindle: Maximum spindle speed: 5,000 rpm Drive power: 15/15/11 kW Torque: 421/302/256 Nm Spindle nose: JIS A2-6 Spindle bore: Ø 73 mm Counter spindle: Maximum spindle speed: 5,000 rpm Drive power: 15/15/11 kW Torque: 421/302/256 Nm Spindle nose: JIS A2-6 Spindle bore: Ø 73 mm Milling spindle: Speed range: 0–12,000 rpm Drive power: 28/23 kW Tool holder: Capto C6 Number of tool positions: 76 Max. tool diameter: Ø 70/Ø 130 mm Max. tool length: 400 mm Max. tool weight: 8 kg Turret: No. of tool holders: 12 Speed of driven tools: 12,000 rpm Square tool shank length: 20 mm Boring bar shank diameter: Ø 32 mm Drive power: 5.5/5.5/3.7 kW Torque: 16.9/13.1/8 Nm Rapid traverse: X axis: 50 m/min Y axis: 40 m/min Z axis: 50 m/min A axis: 36 m/min X2 axis: 25 m/min Y2 axis: 18 m/min Z2 axis: 40 m/min B axis: 100 rpm Through-bore clamping device: Ø 67 mm Operating hours: approx. 15,050 h Spindle hours: approx. 4,210 h Technical features and accessories: - Kitagawa 8-inch through-bore chuck BB208A621 Ø 210 mm on main and counter spindle - Dual foot switch for spindle 1 and spindle 2 - Chuck cylinder stroke monitoring (linear position monitoring) for spindle 1 and spindle 2 - Full indexing of the tool spindle - Turret tailstock function - Suitable coolant: water-soluble coolant - Chip conveyor - Hydrajet MS30-1000/70 bar coolant system - Coolant chiller - Air blast device for chuck (spindle 2) - Interface for mist extractor - Manual tool presetting device installed on the machine (removable, spindle 1 and spindle 2) - Fully closed control loops for X, Y, and Z axes (tool spindle) - In-machine workpiece measuring system, Renishaw RMP600 - 4-color signal tower - Multi-dry filter - Voltage: 380 V, Frequency: 50 Hz - Alternating spindle speed - Prepared for 3D quickSET - Open pocket and island milling - High-speed fixed cycle - X-axis direction, JIS/ISO-compliant - 3D machine model - Transformer Accessories, depicted tools, and clamping devices are only included in the scope of delivery if specifically stated in the additional information. Technical data and specifications are subject to change and errors. Prior sale reserved!

Condition: good (used), Year of construction: 2013, functionality: fully functional, spindle speed (min.): 3,000 rpm, feed length Y-axis: 500 mm, Year of manufacture: 2013 Chuck diameter: 10" Number of axes: 3 Length: 500 mm Swing diameter: 400 mm Spindle speed (rpm): 3000 Ppedox Nmuaspfx Adbel Machinable materials: Steel, Aluminum, Titanium, Graphite, Copper, Invar, Composite, Delrin, Peek

Condition: used, Year of construction: 2005, revolutions per minute 8000 U/min x-travel 1000 mm Psdoud Al Hepfx Adbopl y-travel 500 mm z-travel 570 mm Control Siemens weight of the machine ca. 5000 KG

Condition: good (used), Year of construction: 2001, M01.43870 frequency 50 Hz voltage 400 V 24 V connected load 48 kW rated current 63 A control Siemens 840 D turning diameter 250 mm turning length 100 mm weight of the machine ca. 7,5 t turning length external / innen 100 mm workpiece length - min. 29 mm Ppedporc Ip Ssfx Adbjl workpiece length - max. 100 mm

Condition: excellent (used), Year of construction: 2020, operating hours: 4,854 h, functionality: fully functional, machine/vehicle number: 0030000718A, spindle motor power: 16 W, spindle speed (max.): 5,000 rpm, travel distance X-axis: 242 mm, travel distance Z-axis: 540 mm, mount diameter: 200 mm, feed rate X-axis: 30 m/min, feed rate Z-axis: 36 m/min, operating hours of spindle: 851 h, spindle torque (max.): 168 Nm, number of tool stations in tool turret 1: 12, number of driven tool stations in tool turret 1: 12, Equipment: documentation/manual, ONLY 851 spindle hours! We are a manufacturer of rubber molded parts and have our own toolmaking department, which we have recently scaled back to focus more on the design and development of tools. The lathe is in very good condition and has been regularly maintained. It was used in our in-house toolmaking mainly for machining mild steel. Due to low utilization, it is now offered for sale. The machine is currently in transport position and connected to power. A viewing can gladly be arranged. Including accessories: - Hainbuch chuck with part clamping up to 200mm diameter - LNS oil mist separator (retrofitted in 2021, approx. 8,000 CHF) - Various turning and milling holders - Table stand for turning and milling holders Ppodpfx Adeyfmihjbel - Transport fixtures - Instructions, manuals

Condition: used, Year of construction: 2008, bar capacity 65 mm number of spindle speeds 5.000 U/min control Siemens 840 D no. of tools in turret 1 12 no. of tools in turret 2 12 no. of tools in turret 3 12 Stk./pcs. tool taper VDI 30 driven tools turning speeds 4.000 U/min travel -x1 axis 165 mm travel -z1 axis 220 mm travel -x2 axis 165 mm travel -z2 axis 150 mm travel -x3 axis 165 mm travel -z3 axis 650 mm travel -y3 axis 80 (+50/-30) mm CNC Turning- and Milling Center | DMG - Sprint 65 linear equipped with main/counter spindle, a 3x turret for driven tools, bar feeder and chip conveyor as well as internal counter-spindle flushing with coolant. The machine is in a well-maintained condition and can be inspected at any time under power. The machine video from the production plant will be shared on request. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Pedpfexbtqijx Adbopl #Tags: Sprint65Gildemeister | Sprint-65 | Sprint65

Condition: like new (used), Year of construction: 2019, We are selling a 5-axis CNC woodworking machining center manufactured in 2019, equipped with a versatile FLEX5 cutting unit with a rotation range of 0-360° and a tilt angle of 0-90°. It is equipped with an 8-slot tool changer and a C-axis on the main spindle, which increases its accuracy and flexibility. It handles cross-sections from 20 x 50 mm to 200 x 455 mm and supports wood lengths up to 13,300 mm. Ppedpsxalnwsfx Adbsl

Condition: used, Year of construction: 2005, turning diameter 640 mm turning length 1.185 mm control SINUMERIK 840D swing diameter 640 mm distance of spindle heads 1500 mm slide I: X1 / Y1 / Z1 / B slide travel X-axis 550 mm slide travel Z-axis 180 mm Z- Travel 1.185 mm B - axis 240 ° feed x-axis 0 - 40.000 mm/min feed y- axis 1 - 24.000 mm/min Feed z- axis 1 - 70.000 mm/min feed B-axis 1 - 20 1/min rapid traverse X/Y/Z 40 / 24 / 70 m/min feed capacity X/Y/Z S6: 7,00/11,00/7,50 kN tool taper HSK 63 turning speed milling-spindle 10 - 12.000 1/min power capacity at 100 % load 13,20 kW power capacity at 40 % load 22,00 kW torque milling spindle 60 / 100 Nm no. of workpieces in the magazine 46 Stück tool length - max. 350 / 200 mm tool diameter 80 mm wotkpiece diameter with 2 vacant positions 120 mm weight of tools max. 6 / 10 kg slide II: X2 / Z2 slide travel X-axis 180 mm Z- Travel 1.050 mm feed x-axis 1 - 24.000 mm/min Feed z- axis 1 - 36.000 mm/min rapid traverse x + z axis 24 / 36 m/min feeding force S6: 11,00/9,00 kN turret (x-stations) 12 tool taper DIN 69880 Ø40 Driven tools - quantity 12 Driven tool turning speed 1 - 4.000 1/min power capacity at 100 % load 10,70 kW torque S1: 32 Nm Slide III - longitudial travel Z3 mm Z- Travel 1.150 mm Feed z- axis 1 - 36.000 mm/min rapid traverse Z-axis 36,00 m/min feed capacity Z - axes S6: 13,00 Nm Main spindle ISM90 turning speed main-spindle 10 - 4.000 1/min Podeydfllopfx Adbepl power capacity at 100 % load 36,00 kW power capacity at 40 % load 45,00 kW max. torque at 40% / 100% load 800 / 630 Nm spindle bore 80 mm turning speed opposed-spindle 10 - 5.000 1/min power capacity at 100 % load 21,00 kW power capacity at 40 % load 28,00 KW max. torque at 40% / 100% load 320 / 240 Nm spindle bore 80 mm total power requirement 70,00 kW weight of the machine ca. 20,00 t dimensions of the machine ca. 8,50 x 4,50 x H3,10 m Machine with SIEMENS SINUMERIK 840D control, main- and counter-spindle, chip conveyor, dust exhauster, DMG-automation WH10top. Main-spindle ISM90: hollow clamping device, C-axis, 3-jaw hydraulic chuck SMW-AUTOBLOK KNCS-NB-315-91 Counter-spindle ISM76: closed center clamping device, C-axis, 3-jaw hydraulic chuck SMW-AUTOBLOK KNCS-NB-315-91 Pick-up device with integrated conveyor belt, automatic protective cover, differential pressure clamps. Incl. pump-frame for coolant - Pump 1: 17 l/min at 80bar - Pump 2: 20 l/min at 8bar - Pump 3: 40 l/min at 20bar Without coolant unit. Was connected to a central coolant-system. Accessories: Hainbuch collet chuck incl. collets Ø30,45,50,55,60,65,72,82,85,90 1 piece workpiece pick-up-gripper for turret

Condition: not inspected (used), Year of construction: 1999, functionality: unexamined, machine/vehicle number: 27578701, turning length: 1,050 mm, turning diameter: 520 mm, spindle bore: 77 mm, rotational speed (max.): 5,000 rpm, controller model: Siemens Sinumerik, TECHNICAL DETAILS Max. turning length: 1,050 mm Turning diameter: 520 mm Max. turning diameter over cross slide: 440 mm Spindle bore: 77 mm Ppedpfx Adjyfphgjbsl Max. spindle speed: 5,000 rpm Drive power: 22 / 15 kW Torque: 672 / 168 Nm Tool interface: HSK 50 Tool stations: 96 TURRET Tool interface: VDI 40 Tool stations: 12 + 12 Driven tools: 12 MACHINE DETAILS Control: Siemens Sinumerik EQUIPMENT Chip conveyor Coolant system Filter system B-axis Swiveling counter spindle

Condition: good (used), Year of construction: 2003, Ref. -No.: 10454 Manufacturer: DOOSAN Type: DAEWOO PUMA 300 MSC Year of construction: 2003 Type of control: CNC Control: FANUC 18i-TB Storage location: Halberstadt Country of origin: South Korea Machine-No.: 0MS19XX Turning Speeds: 4500 RPM Bar passage: 62 mm Turning Length: 595 mm Turret places: 12 Pcs Further information: - 4 axes (X/Z/C/B) - counter spindle - driven tool station - finished part removal system - conveyor belt - chip conveyor - Powercool coolant system - LNS Quickload Servo 3 bar loader Ppedpox Sw E Iofx Adbsl - tool holder - collet holder - collets Machines can be inspected under power by appointment.

Condition: good (used), Year of construction: 2010, Ref. -No.: 10287 Manufacturer: DMG Type: DMC 210 FD Year of construction: 2010 Type of control: CNC Ppodpfxoxxn Uko Adbsl Control: Heidenhain Mill Plus Storage location: Halberstadt Country of origin: Deutschland X-Travel: 2100 mm Y-Travel: 2100 mm Z-Travel: 1250 mm Machine length: 11.000 mm Machine width: 5.000 mm Machine Height: 3.500 mm Max. Workpiece diameter: 2500 mm Max. Workpiece Weight: 6.000 kg Max. rotary table diameter: 1.850 O Table speed range: 250 min/-1 Tool Taper: HSK-A100 Tool Piece Magazine With: 183 Pcs./pcs. Spindle Speed: 12.000 RPM Max. Torque On The Boring Spindle: 288 Nm Max. Torque: 2.000 Nm Feed Speeds X/Y/Z Axis: 30.000 mm / min Max. Workpiece height: 1.460 mm axes: 5 Further information: Turning and milling center incl. pallet changing system Gear spindle Coolant treatment system, with belt filter, 710 x 50mm 1 Knoll 600S2 chip conveyor 2 Losma oil mist extraction units 1 steel platform (storage space for clamping device): 5,300 x 2,900 mm - Axes renewed 11.2024 - New encoder, electrical components renewed - Geometry protocols available Machine is still in production and under power. The machine can be viewed at any time by appointment.

Condition: used, Year of construction: 1999, operating hours: 65,090 h, functionality: fully functional, ET365 GS with bar feeder and chip conveyor The machine is fully equipped - Collection tray - High-pressure pump Pjdpfxjycvaqo Adbopl - Control cabinet air-conditioning unit - Kupa loader - The machine was purchased from a running production operation and has been technically inspected - Geometry measured and all settings adjusted - Wearing parts replaced - All functions checked and adjusted as required The machine is fully operational and ready for immediate production The machine is available immediately

Condition: like new (used), Year of construction: 2013, operating hours: 7,100 h, functionality: fully functional, turning length: 650 mm, turning diameter over cross slide: 350 mm, turning diameter: 385 mm, spindle speed (min.): 4,500 rpm, spindle bore: 67 mm, travel distance X-axis: 255 mm, travel distance Z-axis: 800 mm, For sale: Used DMG NEF400 V3, 5th Generation ISM 2-axis universal lathe with C-axis. Travel distances: X: 255mm Z: 800mm Swing over bed: 385mm Swing diameter: 350mm Turning length: 650mm Equipment: - Main spindle as integrated spindle motor - Max. spindle speed: 4,500 rpm - Drive power: 8.0/11.5 kW (100/40% duty cycle) - 12-position VDI30 disc-type turret with 6 driven positions - C-axis and spindle brake (hydraulic) - Automatic tailstock, MK4 mounting, travel: 680mm - CNC control Siemens 840D Solutionline with ERGOline Control, Sinumerik Operate, and ShopTurn 3G - Operating system: Linux Podpjxzqnrjfx Adbspl - Technology cycle for applying alternating spindle speeds for vibration-critical setups - Manual tool measurement device in work area - Hydraulic unit - Coolant spray gun - Mechanical oil mist separator - Reinforced coolant pump: 12 bar, 23 l/min - Chip conveyor with discharge height of 1,250mm, discharging to the right Bar machining package consisting of: - Workpiece pickup unit with left-side conveyor for parts up to max. 65mm diameter, 150mm length, and 3kg max. weight - Bar clamping device inner draw-tube diameter max.: 67mm - Interface for bar loader magazine - Foot switch for tailstock operation - Hydraulic 3-jaw chuck SMW-AUTOBLOK - RMS sensor (Relocation Machine Security) Machine available immediately! Machine ready for operation! Loading by us included! Transport can be arranged upon request!

Condition: like new (used), Year of construction: 2011, operating hours: 9,080 h, functionality: fully functional, For sale: Well-maintained CNC turning and milling center DMG Mori Seiki NLX 2500 SY/700, year of manufacture 2011, equipped with Mitsubishi 730 BM control! Only approx. 9,000 operating hours! Travel axes X-axis: 260 mm Y-axis: 100 mm Pjdpfjxzqhrex Adbjpl Z-axis: 795 mm Equipment and accessories: - Tool turret: 12 stations, all powered - Driven tool speed: Max. 10,000 rpm - Parts catcher - Electrical connection: 400 V - Power consumption: 37.6 KVA - Internal cooling: available - Main spindle chuck: Kitagawa BB210AB - Sub-spindle chuck: Kitagawa B206A521F - Swing diameter: 366 mm - Turning length: 705 mm - Spindle bore: 80 mm - Main spindle max. speed: 4,000 rpm, with 3-jaw chuck - Main spindle power: 18.5 kW - Sub-spindle max. speed: 6,000 rpm, with 3-jaw chuck - Chip conveyor - Tool measurement system in the working area - Manually deployable measuring arm for sub-spindle - Short bar loader, manufacturer: LNS - Includes tools: 8 fixed tools, 3 driven tools - Includes extraction system, brand: Indusa - Includes complete documentation Machine available immediately! Machine has been fully cleaned and inspected! We will undertake loading of the machine! Transport can be organized upon request!

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, For sale: Well-maintained EMCO Hyperturn 665 MC Plus with IEMCA Master 880MP-E bar loader, chip conveyor, and high-pressure coolant pumps! Machine was exclusively used for machining brass parts! CNC Turning and Milling Center | EMCO Hyperturn 665 MC Plus with main and sub-spindle, C and Y axes, dual turrets each with 12 driven tool stations! Technical Data: Swing diameter over bed: 600 mm Swing diameter over cross slide: 500 mm Control: Siemens Sinumerik 840D Max. turning diameter: 430 mm Max. turning length: 744 mm Max. bar capacity: 65 mm Travel - X: 270 mm Travel - Z: 750 mm Travel - X2: 205 mm Travel - Z2: 750 mm Travel - Y: 100 (+/- 50) mm Main spindle speed: 0 - 5,000 rpm Sub-spindle speed: 0 - 7,000 rpm Tool turret: 2x 12 positions, all driven! Tool holder: VDI 30 Upper turret: X, Z, Y axes Lower turret: X, Z axes Sub-spindle traverse (left/right): Z3 axis C11 spindle: 65 mm diameter (hollow chuck cylinder) Ppodoxzq Ncepfx Adbsl C12 spindle: 45 mm diameter (solid chuck cylinder) with part ejector Tool turret type: Sauter 2x 14 bar high-pressure pumps Accessories: Complete tooling cabinet with driven and static toolholders as well as carbide inserts and tool holders Collet chucks for main and sub-spindle Full documentation etc. Machine available immediately! Ready for operation! Loading will be handled by us! Transport can be organized upon request!