Used Elgo for sale (83)

Condition: excellent (used), Year of construction: 2017, operating hours: 14,500 h, functionality: fully functional, 1,0 St. gebr. Zweikomponenten Spritzgießmaschine mit Roboter und Drehteller Hersteller: ARBURG Typ: 470S1100-400/290 Baujahr: 2017 Schließkraft: 110 Tonnen Holmabstand 420 x 420 mm Einbauhöhe min. /max.: 450 mm Öffnungsweg: 950 mm Schnecken DN 1: 35 mm Max. Hubvolumen: 154 cm³ Spritzteilgewicht: 141 g/PS Schnecken DN 2: 30 mm Hubvolumen: 106 cm³ Spritzteilgewicht: 97 g/PS Steuerung: SELGOCIA Ausstattung: 3 x Kernzüge Vertikale Spritzeinheit Drehteller 6 - ACHS Roboter, Hersteller: KUKA, Typ: KR 16 Wikut, Baujahr: 2010 Förderband Ndodpfx Aaeu E E Sujnof Schutzzaun

Condition: used, functionality: fully functional, Year of construction: 2004, Hydraulic Guillotine Shear Make: ERMAKSAN Model: HGS 3100x6 Year: 2004 Technical Data: Manufacturer: ERMAKSAN Model: HGS 3100x6 Year of Manufacture: 2004 Sheet Width: 3,100 mm Sheet Thickness: 6 mm Cutting Angle: 1.2° Strokes per Minute: 18 Number of Hold-Downs: 15 Motor Power: 11 kW Back Gauge: 1,000 mm Space Requirement: L 3.8 x W 2.2 (plus support arms) x H 1.6 m Machine Weight: 5.5 t Nedpfx Aaexrtxuonodf Equipment: • Angular stop • Support arms • Programmable 1,000 mm back gauge via ELGO controller • Automatic blade gap adjustment • Pneumatic sheet support device • Cutting length limiter • Folding finger guard • Light barrier for rear area safety All information is provided without guarantee. A powered demonstration is available at any time in our showroom.

Condition: used, Year of construction: 2008, sheet width 3100 mm plate thickness 6 mm rear stop 1000 mm Ndedpfxsvuz Tps Aanjf cutting angle 1,2 ° down holder 14 Stk no. of strokes 18 Hub/min oil volume 150 l total power requirement 11 kW dimensions of the machine ca. 3900 x 1900 x 1600 mm weight 5500 kg Equipment: - Hydraulic swing cut shears - ELGO control system - Electric backgauge 1000 mm - Manual cutting gap adjustment - Cutting length limitation - Ball rollers in the table - 2x front support arms - 1x front side stop with scale - Front finger guard, hinged - Rear safety device (protective grille + light barrier) - Foot switch - Operating instructions

Condition: excellent (used), Year of construction: 2012, Trumpf Trushear 5063 (2012) Guillotine Shear 3050x6mm Manufacturer: Trumpf Model: TruShear 5063 Year of manufacture: 2012 Condition: used, very good Control: ELGO P50 Cutting length: 3050 mm Sheet thickness: 6 mm / 4 mm for stainless steel Cutting angle: 0.5 – 2.8° Blade gap adjustment: 0.05 – 0.72 mm Automatic cutting angle adjustment Automatic blade gap adjustment Automatic blade gap compensation Hold-down devices: 20 pieces Strokes per minute: 18 – 38 Backgauge: 10-1000 mm, adjustable Total power requirement: 11 kW Oil capacity: 140 L Dimensions (approx.): L 4.00 x W 1.67 x H 1.90 m Total weight: approx. 7.2 t Customs tariff number: 84615090 Sheet support device Sheet return device Small parts chute 3x support arms Light barrier Foot pedal Nedpfjxrv Apex Aansdf Documentation

Condition: good (used), functionality: fully functional, Year of construction: 1991, This high-performance swing beam guillotine shear RAS 83.30 with ELGO NC backgauge and pneumatic sheet support unit comes from first ownership. Cutting capacity: 3190 x 2.5 mm Drive power: 5.5 kW Machine weight: 2800 kg Nsdpfx Ajxmi Dpjanedf Includes pneumatic sheet support unit, ELGO NC backgauge, 1 left-side squaring arm, and 3 additional support arms. Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: ready for operation (used), Elgo CNC controlled machine, very easy and user-friendly Nodpexpghqofx Aanodf max tube cap: dia 76 mm x 4 mm thickness max square tube: 70 x 70 mm max radius: 600 bending angle: 180° Standard tooling 3D Special tooling on request Length: 1200 mm Width: 800 mm Height: 1300 mm

Condition: excellent (used), Year of construction: 2010, operating hours: 44,600 h, functionality: fully functional, 1,0 St. gebr. Zweikomponenten Spritzgießmaschine mit Roboter Hersteller: ARBURG Typ: 570S2200-400/170e² Baujahr: 2010 Schließkraft: 220 Tonnen Holmabstand 570 x 570 mm Einbauhöhe min. /max.: 350 mm Öffnungsweg: 1.000 mm Schnecken DN 1: 35 mm Ndodpfx Aou E E H Sjanef Max. Hubvolumen: 154 cm³ Spritzteilgewicht: 141 g/PS Schnecken DN 2: 30 mm Hubvolumen: 59 cm³ Spritzteilgewicht: 47 g/PS Steuerung: SELGOCIA Ausstattung: 3 x Kernzüge Vertikale Spritzeinheit 6 - ACHS Roboter, Hersteller: KUKA, Typ: KR 16 Wikut, Baujahr: 2010 Förderband Schutzzaun

Condition: good (used), functionality: fully functional, Year of construction: 1991, sheet thickness steel (max.): 16 mm, cutting length (max.): 6,000 mm, HYDRAULIC SHEAR LVD MVSB 62/16 Serial number 18478 Yom 06/1991 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 6200mm Distance between uprights 6400mm Gap 60mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.5° Min. number of strokes/min. 6 Max. number of strokes/min 25 Min. blade clearance 0.05 mm Max. blade clearance 1.6mm Motor power 30kW Approx weight 35000 Kg LxWxH 7100x2400x3000mm Accessories included; ELGO P85 “GO-TO” for back gauge Electrical adjustment of back gauge 1000mm Ndodpeumhm Asfx Aanof 1 x Front support 2mtr, one with 90° square arm front support L2000mm Foot pedal Ball bearings on table Inclinable back gauge with manual hydraulic pump

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display - Manual cutting gap adjustment - 1x side stop with mm scale - 2x support arms - 1x freely movable double foot switch - Front finger guard Nodjuagxpspfx Aanedf Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

Condition: new, functionality: fully functional, planing width: 530 mm, number of planer blades: 4, Equipment: motor brake, Houfek R 530 surface planer - 400V/50Hz, 5.5 kW (7.5 HP), width 530 mm 1.1 Motor 5.5 kW (7.5 HP), Tersa cutterhead Njdpsu Rnqqofx Aanodf 1.2 Total work table length 3100 mm 1.3 Dimension of the guide ruler 1300x150 mm with tiltable auxiliary ruler 1.4 Planed table 1.5 Upper control panel with ELGO Z60 digital display Electronic adjustment of the take-off 0 - 7 mm Tilt angle of the tiltable ruler 0°- 45° - Digital display Adjustment of the input table inclination (pointed/hollow joint) 1.6 Cover for the SUVAMATIC planing roller 1.7 4-knife planing roller D=120 mm 1.8 Automatic star/delta start of the motor 1.9 Electromagnetic brake 1.10 Suction nozzle with outlet D=150 mm 1.11 Blade setting gauge 1.12 Voltage 400V/50Hz 1.13 Packed in PE film as standard 1.14 Machine built according to CE power and safety standards

Condition: used, Hydraulic guillotine shears FASTI Type 509 - 25/4 Machine no. No. 5418 Year of construction 1991 Cutting length 2535 mm Cutting thickness 4 mm Backgauge 5-1000 mm (controlled) Cutting angle adjustable Hydraulic pressure max. 290 bar Motor power 7.5 kW Mains connection 400 Volt, 50 Hz - Back gauge with positioning control ELGO ELECTRIC type 85 - Sheet holding device under the back gauge - Manual cutting gap adjustment with dial gauge display right and left - stepless cutting length adjustment - Hydraulic cutting angle adjustment via hand pump Nedpet Apumefx Aanedf - front angle stop left 1300 mm - 14 sheet hold-down devices - electric foot switch - very solid and torsion-resistant welded construction - 1 set of original FASTI replacement blades (4 pieces, presumably new and unused) space requirement L x W x H 3100 x 2350 x 1700 mm weight 3500 kg good condition

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, control type: CNC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Elgo, controller model: P40T, working width: 3,100 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, stroke rate (min.): 8 1/min, stroke rate (max.): 20 1/min, sheet thickness (max.): 13 mm, sheet thickness aluminum (max.): 10 mm, sheet thickness steel (max.): 13 mm, sheet thickness stainless steel (max.): 8 mm, back gauge adjustment: CNC-controlled, back gauge: 1,000 mm, power: 22 kW (29.91 HP), input voltage: 400 V, input current: 45 A, input frequency: 50 Hz, type of input current: three-phase, overall weight: 12,000 kg, total length: 4,000 mm, total width: 2,200 mm, total height: 2,100 mm, number of support arms: 2, Equipment: CE marking, emergency stop, finger protection, foot remote control, safety light barrier, 2021 MVD B13-3100 Guillotine Shears with Elgo P40T Control – Very Good Condition For sale is a 2021 MVD B13-3100 Hydraulic Guillotine Shear, equipped with the advanced Elgo P40T CNC Control. This machine is in very good condition, having been installed in 2021. The MVD B-Series shears are built for precision, productivity, and reliability, offering powerful hydraulic cutting performance with CNC-controlled accuracy. Perfect for fabrication shops, subcontractors, and sheet metal production. Machine Make: MVD Machine Model: B13-3100 Machine Type: Hydraulic Guillotine Machine Capacity: 3m x 13mm Machine Year: 2021 ✅ Key Features 3100 mm cutting length – handles large sheet sizes with ease 13 mm sheet capacity (mild steel) – robust heavy-duty performance Elgo P40T CNC Control – programmable backgauge, stroke, and cutting settings Hydraulic swing beam design – consistent and accurate cutting results CNC backgauge system with motorised adjustment Rugged welded frame for stability and precision Front sheet supports and squaring arm for operator convenience Safety light guards for operator protection Very Good condition – 2021 model, very low hours 📐 Technical Specifications – MVD B13-3100 Guillotine Shears Cutting Length: 3100 mm Capacity (Mild Steel): 13 mm Capacity (Stainless Steel): ~8 mm Backgauge Travel: 1000 mm (CNC controlled) Control: Elgo P40T CNC touchscreen – programmable stroke, backgauge, cutting angle Stroke per Minute: 8–20 (adjustable) Cutting Angle: 0.5°–2.5° adjustable Throat Depth: ~100 mm Main Motor Power: 22 kW Hydraulic System: High-pressure precision hydraulics Dimensions (L×W×H): ~4000 × 2200 × 2100 mm Weight: ~12,000 kg 🌍 Condition Year of Manufacture: 2021 Control: Elgo P40T CNC Model: MVD B13-3100 Condition: Very Good – lightly used Ndsdpfx Aoxddzqoanef Ready for inspection and immediate delivery 🔑 Summary This 2021 MVD B13-3100 Hydraulic Guillotine Shear with Elgo P40T CNC Control offers 3100 mm cutting length, 13 mm capacity, and CNC accuracy. A modern, reliable, and powerful sheet metal cutting solution ideal for fabrication, subcontracting, and production facilities.

Condition: used, Used guillotine / shear for sale with non ferrous falling sheet support Used guillotine / shear for sale with non ferrous falling sheet support EDWARDS PEARSON D.D 2500mm x 3.5mm mechanical Guillotine for sale Direct drive guillotine / reliable sheet metal cutting machine Model: Truecut Control programmable / Front operated back gauge Datum Elgo control Back stop / back gauge Rapid blade gap adjustment Squaring arms Front sheet support arms Rear infra-red safety guarding Roving foot switch Year 1999 Can be seen working Manufactured in England Current blades are in good condition however new blades are available at extra cost Nsdpfjfuam Hsx Aansdf Delivery and installation available at extra cost Also 2metre, 3metre dd guillotines for sale. Also Keetona Hydraulic guillotines for sale

Condition: used, functionality: fully functional, controller manufacturer: Elgo, controller model: Z16, working width: 3,100 mm, sheet thickness steel (max.): 10 mm, back gauge adjustment: motor-driven, overall weight: 8,250 kg, Capacity: 3100 x 10 mm. Backgauge: Motorized. With Elgo Z16 digital readout. Adjustable cutting length: Yes. Adjustable blade gap: Yes. Country of origin: France. Ndodexphaujpfx Aansf Size (L x W x H): 3800 x 2900 x 1600 mm. Weight: 8250 kg. Swing beam shear. With squaring arm and 3 support arms. All our machines will be tested and serviced before delivery.

Condition: used, Year of construction: 1985, sheet width 3100 mm Ndsdoxab Tvopfx Aanef plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Condition: good (used), Year of construction: 1995, Max. cutting length 3050 mm Material thickness 37 kg/mm² 12 mm Material thickness 70 kg/mm² 8 mm Cutting angle 1.8 degrees Stroke rate 8 - 13 min. Number of hold-down clamps 12 Drive power 18.5 kW Dimensions L x W x H 4150 x 1950 x 1950 mm Weight 8000 kg Accessories / Special features: • ELGO Type 71 motorized NC positioning control for the backgauge, length approx. 900 mm • If necessary, the toggle lever system allows the machine to operate with only one cylinder at a reduced cutting capacity of approximately 55% of the nominal capacity. This simultaneously increases the cutting sequence for more efficient work with thin sheet metal. Switching from fast to slow is done using a selector switch on the control panel. • Hydro-mechanical drive via a powerful toggle lever • Easy cutting gap adjustment on both sides • 2 cylinders mounted externally on the machine, easily accessible • Vertical, stable guides • Upper and lower blades each with 4 cutting edges • Hydraulic overload protection • Proportional force of the hold-down clamps • The machine frame is a fully welded construction and is machined in one setup (no screwed parts) • Portable electric foot switch • Blades suitable for black sheet metal and stainless steel • Ball transfer units in the table • 1 angle stop • 1 support arm • CE-compliant Ndodpovkw Dvjfx Aanef Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1998, Hydraulic shear LVD HST-C 40/6.35 Year of construction 1998 Serial number 25379 Technical specifications Max sheet thickness 6.35 mm Cutting length 4050 mm Back gauge range 1000 mm Cutting angle 0.5°-2° Blade clearance 0,05-0.8 mm Number of strokes per min 10-45 Number of hold dawns 21 motor 7.5kW weight 9500 kg oil 150l Ndsdpexcf Snefx Aansf Voltage 3 x 380V included : ELGO P85 for back gauge Security norms CE 1 square arm from support L1000mm 1 extra support L1000mm

Condition: good (used), Year of construction: 1991, sheet width - max. 1010 mm plate thickness 4.0 mm ST Nedpfxoxrgv Ts Aansdf plate thickness 2.5 mm VA plate thickness 6.0 mm ALU number of strokes - loaded max. 20 Hübe/min cutting angle 1.5 ° work height max. 900 mm Control ELGO total power requirement 5.5 kW weight of the machine ca. 2200 kg. range L-W-H 1500 x 2155 x 1606 mm from a maintenance workshop good condition (!!) - in checked conditions - machinevideo - ?v=w22S17mfU-A Equipment: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge * Includes NC ELGO positioning control "TYP 85" - Electric cutting length limiter - Manual cutting gap adjustment - 1x side stop with scale - 2x support arms - 1x freely movable foot switch - Original operating instructions * Special accessories included: - Pneumatic holding device for thin sheet metal blanks

Condition: used, Year of construction: 1999, sheet width 3060 mm plate thickness 8.0 mm thickness at "Niro-steel" 6.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes max. 10 - 15 Hub/min oil volume 160 ltr. cutting angle 1.6 ° back stop - adjustable 6.0 - 750 mm Control ELGO P9521 Ndjdpoxaci Esfx Aanof total power requirement 18.5 kW weight 6300 kg range L-W-H 3900 x 2300 x 1630 mm Features: - Robust electro-hydraulic swing beam shear - ELGO digital display model P9521, for electric backgauge * Backgauge travel X = 750 mm * Backgauge-free ball screw drive * Travel speed 100 mm/s - 1x stable side stop * With T-slot, flip-stop, and millimeter scale - 2x stable front support arms - Electric cutting length limiter * Cutting length limiter to increase the stroke rate/min. - Manual cutting gap adjustment * Centrally operated on the right side stand - Front support plates - Front finger/interference guard - Inching operation with push buttons on the left control panel - Protective grille = safety device behind the machine - Operating instructions (PDF)

Condition: used, Year of construction: 2000, sheet width 3060 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm distance between columns 3100 mm down holder 16 Stück no. of strokes 20 Hub/min oil volume 160 ltr. cutting angle 1.6 ° Control ELGO Number of working hours ~ 1.100 h total power requirement 11.0 kW weight 5250 kg range L-W-H 3800 x 1940 x 1560 mm from a maintenance workshop with only approx. 1.100 operating hours (!!) Equipment: - electro-hydraulic swing beam shears - ELGO NC control unit * for electric back stop * Input of target/actual position value possible - NC electro-motoric back stop Ndodpfoxacfaex Aansf * travel path of back stop X = 750 mm * back stop ball screw with no play * travel speed 100 mm/sec - electric cutting length limitation * cutting length limitation to increase the number of strokes/min. - manual cutting gap adjustment, via eccentric - tip operation with push buttons on the control panel on the left - front support plates with ball rollers - front finger/interference protection - 1x side stop with T-slot & millimeter scale - 2x front support arms - original operating instructions including CE declaration

Condition: used, Year of construction: 1997, sheet width 3230 mm plate thickness 2.5 mm thickness at "Niro-steel" 1.5 mm no. of strokes 28 - 42 Hub/min cutting angle 1.60 Grad table height 820 mm distance between columns 3540 mm Control ELGO 87P engine output 6.8 kW weight of the machine ca. 3410 kg. range L-W-H 4070 x 2070 x 1400 mm from a maintenance workshop including special accessories (!!) Ndodoxacd Njpfx Aansf Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - NC electro-motorized back stop - including NC ELGO "TYP 87P" digital control unit * adjustable from the front right * with target/actual value position input * continuous adjustment over the entire travel range * rough adjustment via push buttons * protection of the limit values ??with limit switch - "Duo-Cut" drive with two dynamic, powerful gear motors - support table with recessed grips - hold-down bar with hard rubber strip - all-steel knife with two cutting edges - selector switch for single and continuous stroke - 1x freely movable foot switch - safety device at the rear - original operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts - 1x extra long side stop, including support foot + digital stop - 2x extra long, front support arms * with "SLIDING" mount - for easy moving

Condition: used, Year of construction: 1990, plate width 2503 mm plate thickness 4.0 mm ST Nodpfxsxabd Uo Aanjdf plate thickness 2.5 mm VA plate thickness 6.0 mm ALU number of strokes - loaded 15 - 20 Hübe/min cutting angle 1.7 ° work height max. 900 mm Control ELGO TYP 85 total power requirement 8.5 kW weight of the machine ca. 3400 kg range L-W-H 2913 x 2250 x 1760 mm Features: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge * with ELGO control unit - Manual cutting gap adjustment - Front support table including recessed grips - 1x sturdy side stop with scale and tilting cam - 2x sturdy front support arms - 1x freely movable foot switch - Front finger guard - Front emergency stop button - Operating instructions (PDF)

Condition: used, sheet width 4080 mm plate thickness 2.0 mm ST thickness at "Niro-steel" 0.8 mm Sheet thickness for ALU 2.5 mm cutting angle 1.3 Grad no. of strokes 34 Hub/min distance between columns 4310 mm back stop - adjustable 15.0 - 750 mm table height 820 mm Control ELGO engine output 9.0 kW weight of the machine ca. 3600 kg. range L-W-H 5250 x 2200 x 1400 mm Good condition (!!) Current new price approx. €70,000 Special price upon request The MHSU motor-driven guillotine shear is based on a torsion-free, rigid welded construction and a dynamic, quiet, and powerful gear motor. High static and dynamic rigidity is ensured by robustly dimensioned main components such as the cutter bar, support table, side supports,and the main drive unit. The motor- driven guillotine shear was developed forsheet metal and plastics processing. With these shears, you can effortlessly produce clean cuts in series. Features: - NC robust, motorized swing cut guillotine shears - with ELGO NC control unit * Digital position display of the backgauge * Adjustable from the front right * With target/actual value input * Continuous adjustment across the entire travel range * Limit switch protection - NC motorized material/backgauge - Shatter-proof, torsion-free welded steel construction - Compact and clearly arranged machine design - Support table with recessed grips - 1x hold-down bar - 1x side stop with T-slot and scale Ndjdpfxjxabc Ro Aanjf - 3x front support arms - 1x freely movable foot switch - Operating instructions Optional accessories included: - Pneumatic sheet metal holding device for thin sheet metal blanks

Condition: used, Year of construction: 1996, sheet width 2040 mm plate thickness 4.0 mm ST plate thickness 6.0 mm ALU thickness at "Niro-steel" 2.5 mm distance between columns 2100 mm no. of strokes ca. 32 Hub/min cutting angle 2.0 ° table height ca. 820 mm Control SCHRÖDER / ELGO total power requirement 5.5 kW weight 3250 kg range L-W-H 2400 x 1400 x 1100 mm From a maintenance workshop Current new price approx. 35.000 euros Special price upon request The MSS motorized guillotine shear was developed for sheet metal and plastic processing. With these shears, you can effortlessly produce clean cuts in series. The MSS "oscillating cut" is the elegant and powerful way to cut. Thanks to the oscillating cut technology, the applied force is optimally converted into a cutting movement, giving the machine power reserves. Features: - Robust, motorized swing-cut guillotine shears - Shatter-proof, torsion-free welded steel construction - Compact and clearly arranged machine design Ndedpfx Aaoxaa Edenef - NC electro-motorized backgauge * with SCHRÖDER / ELGO NC control unit - Manual cutting gap adjustment * Centralized - adjustable with a simple handle - 1x hold-down bar - 1x sturdy 1.000 mm side stop - including T-slot and mm scale - 2x front support arms 1.000 mm - Grip recesses in the support table - 1x freely movable foot switch - Rear sheet chute - Operating instructions

Condition: used, Year of construction: 2004, pressure 60.0 t chamfer lenght 2600 mm distance between columns 2050 mm column arm 310 mm working feed 10.0 mm/sec return speed 61.0 mm/sec Nsdpfxjw U U Tte Aansdf stroke 100 - 140 mm dayligth 450 mm table height 860 mm oil volume 100 ltr. Control ELGO P8822 operating pressure max. 200 bar Number of working hours ca. 2.370 h voltage 380 V total power requirement 5.5 kW weight of the machine ca. 5000 kg. range L-W-H 3000 x 1850 x 2050 mm good / well-maintained condition (!!) with only approx. 2,370 operating hours current new price approx. 60.000 euros special price on request in checked conditions - machine video - ?v=PsUeM3O5wAM Equipment: - NC electro-hydraulic press brake - with ELGO NC control unit "P8822" * Input of target/actual values ??for back stop * Input of target/actual values ??for depth adjustment ` * swiveling operation, front left * manual mode selectable - NC controlled axes: Y1 + Y2 + X - NC electro-motorized back stop, on ball screws * with 4x manually adjustable stop fingers * adjustment in R+Z axis (manual) - Upper tool holder SYSTEM A (AMADA), with upper wedge crowning * 1x split set of upper tools * clamping jaws with clamping lever (quick clamp) - 1x universally rotatable MULTI V die block - 2x side-hinged doors (protective device) - 1x rear sliding door (protective device) - 2x front stable support arms - 1x freely movable foot control (on rollers - movable) - Operating instructions (PDF)