Used Extrusion Plastic Line for sale (15,554)

Year of construction: 2024, operating hours: 10 h, condition: ready for operation (used), functionality: fully functional, screw conveyor diameter: 145 mm, TECHNICAL DETAILS Throughput (depending on material, bulk density, and recipe): 200 - 300 kg/h Extruder type: Single-screw extruder / melt extruder Screw diameter: 145 mm Heating: Induction heating Heating processing temperature: over 300°C possible MACHINE DETAILS Drive Drive power: 45 kW Voltage: 380 V Frequency: 50 Hz Rated current: 84.2 A Speed: 1,480 rpm Protection class: IP55 Insulation class: F Operating mode: S1 – continuous operation Sound level: 71 dB(A) Hodpfxozr Hz Ae Airjw Year of drive manufacture: 2022 Star/delta connection possible Suitable plastics: LDPE, HDPE, PP Suitable materials: Ground material, EPS, film scraps, ground film, and light plastic waste Material feed: Suitable for materials with low bulk density Operating hours: 10 h EQUIPMENT Metering device Hopper for material feed Large filter / screen changer Adapted die

Condition: ready for operation (used), Plastic Film Wash Line with Extruder Available in Ireland Can be seen running if necessary Sink Float Tank Centrifuge Washer Dryer Extruder Granulator Shredder Everything required for the washing and recycling of Plastic Material Hsdpfozylxiex Airjw 1 Tonne per Hour

Condition: used, Year of construction: 1970, functionality: fully functional, BARMAG extrusion system consisting of: 1x BARMAG BA KEP 90-26.3-S extruder 1x BARMAG 9E4-11-103/Z transmission gear 1x AEG G 16.04 drive motor with forced ventilation, 460V, 112A, 46.7KW, 3150rpm, rated at 330V, 2.21A 1x SCHOLZ dosing unit, incl. Feed hopper 1x Control unit System features: - Single-screw extruder, built around 1970 - Throughput 200 kg/h - Conversion to new screw geometry in 2016 - Screw diameter 90 mm - Screw length 2769.5 mm Hedpfx Aisuakzzorjw - Process length 26.3D - Geometry: Feed - Barrier - Mixing section - Screw material: 1.8550, nitrided - DC motor - Technical documentation This system is available in three versions. Subject to prior sale. Please send inquiries via email only. Note: The machine is still installed and can be inspected on site. The buyer must dismantle it and arrange shipping themselves. This is not included in the offer price.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, Rubber extrusion NBR&PVC Insulation sheet production line / available immediately The machine line can be delivered immediately, with few operating hours and in new condition. Production line units: 1. Zhejiang Baina 150 20D 1000Kg/h cold feed vacuum extruder (Standard) 2. Zhejiang Baina EJ-PPF-150-04-00 conical die (Pneumatic) 3. Zhejiang Baina 6m infrared curing oven (width 1000mm) 4. Zhejiang Baina 6m hot air curing oven (width 1140mm) 5. Zhejiang Baina 6m hot air curing oven (width 1440mm) 6. Zhejiang Baina 6m hot air curing oven (width 1600mm) 7. Zhejiang Baina 6m hot air curing oven (width 1800mm) 8. Zhejiang Baina 6m hot air curing oven (width 2000mm) 9. Zhejiang Baina 6m hot air curing oven (width 2300mm) Hodpfx Aey Exrpsirew 10. Zhejiang Baina 6m hot air curing oven (width 2500mm) 11. Zhejiang Baina 6m hot air curing oven (width 2800mm) 12. Zhejiang Baina 36M FF-SLX-02-00 (3 layers * 12m) cooling system 13. PCM automatic longitudinal and transverse industrial cutting machine 2000mm 14. AC-15AD liquid chiller with 285 liters water tank If you are interested, we will send you a detailed description and data.

Condition: used, Technical Details: 1 Nextron Technologies Main Extruder NMA30-24D, 1998, 98S01059-01 2 Nextron Technologies Heating, Drive & Control Cabinet, 1998, 98S01059-01 3 Maillefer Secondary Extruder A-CMPT, 2006, Y6S01032-01 4 Maillefer Cooling Bath, Type BAC CB32, N/A, 875738.1 5 Betol Cooling Bath, N/A, A3604* 6 Zumbach Electronic Measuring and Control Unit, N/A, 002589* 7 Kabel Technik Haul-Off Unit, Type KT1983, N/A, Unknown Hjdpez Szpmofx Airow 8 Zumbach Electronic Control / Electronic Unit, Type WALL IPC-EE-0450-A, N/A, SO-00009082 9 Zumbach Electronic Electronic Unit, Type ODAC 18XY-J, N/A, SO-00009080

Condition: refurbished (used), Year of construction: 1991, functionality: fully functional, Complete extrusion line for PVC profiles, fully overhauled and tested EXTRUDER: • IDE 75/25 type ME7/3 • single screw, PVC profile geometry and barrel in good condition • screen control (retrofitted by the manufacturer) • year of manufacture: 1993 • 35kW motor, 4 to 40 rpm COEXTRUDER: • IDE MEB 30/25D • Single screw Ø30mm 25LD • PVC profile geometry screw and sleeve in good condition • Year of manufacture: 1992 • 3.8kW motor, 6 to 64 rpm CALIBRATION : • IDE • Length: 2 metres • 2 vacuum pumps, 16 valves • 14 water valves Hsdpfx Asya Eldjirew • Manual horizontal and longitudinal adjustments HAUL OFF: • IDE ME30/5 • Year of manufacture: 1993 • Contact length: 1100 mm • Width: 100 mm CIRCULAR SAW • IDE ME52 • Blade: 300 mm • Pneumatic carriage travel 180 mm • Year of manufacture: 1991 TILTING TABLE • IDE • Length: 4000 mm • Pneumatic movement Everything is in very good overall condition, the machines are very clean and ready for use.

Year of construction: 2006, condition: used, functionality: fully functional, Complete Extrusion Line for Plastic Pipes Luigi Bandera / Graewe / Supertech Year of manufacture: 2006 For sale: Complete extrusion line for the production of plastic pipes. Installed in a mobile container setup = 3 x 40-foot sea container. (Walking Pipe system). Ideal for mobile production or limited space. Specifications: Extruder: Luigi Bandera S.p.A. Year of manufacture: 2006 Serial number: 251371 / 251372 Downstream processing / cooling line: Supertech Industrie – Walking Pipe system Saw / cut-off unit: Graewe GmbH Type: RA 250/4 Year of manufacture: 1999 Control system: Krauss Maffei Installation: fully integrated in container (plug & play concept) Description: This robust extrusion line is suitable for the production of plastic pipes (PE/PP/PVC depending on configuration). The line consists of a powerful Bandera extruder, followed by a complete calibration, cooling and transport section (Walking Pipe), and a Graewe cut-off saw. Applications: Drainage pipes Cable protection pipes Industrial pipelines Irrigation systems 💬 Price on request Hsdszbkkhjpfx Airow 📍 Viewing possible by appointment; address = 7822 Ath, Belgium Keywords: Technical / industrial Extrusion machine Extrusion system Extrusion line Screw extruder Melt processing machine Plastic processing machine Pipe production machine Profile extrusion machine Continuous forming machine Melt and forming system

Condition: ready for operation (used), Year of construction: 1995, operating hours: 39,000 h, functionality: fully functional, Equipment: documentation/manual, A used and functional profile line for rigid PVC-profiles (300 x 100 mm), consisting of: Twin-screw extruder (parallel) Manufacturer: WEBER Type: DS 7.22 Year of manufacture: 1995 Machine no.: DS70-043 Operating hours: 39,000 hours Screw diameter: 70 mm Effective screw length: 22 x D Screw geometry: for rigid PVC profiles Torque: 4,500 Nm per screw Screw speed: max. 40 rpm, continuously adjustable Drive motor: DC low-voltage motor, thyristor-controlled Drive power: approx. 25 kW Cylinder heating/cooling zones: 5/3 (air cooling with fan) Adapter heating zone: 1 Tool heating zones: 5 Control: conventional control with digital temperature controllers Degassing: Busch rotary vane vacuum pump (1.5 kW) Output capacity, max.: 120-150 kg/h for hard PVC, depending on material Connected load: approx. 50 kW (without tool) Special accessories: Mass temperature sensor and mass pressure sensor Adapter between extruder connection and extrusion tool Used tool set for a window profile (widening), consisting of: - Extrusion tool ‘widening’, incl. heating bands - Dry calibration - Vacuum tank approx. 2 m long, with 8 slots for calibration discs - 16 calibration discs Vacuum calibration unit Manufacturer: Uniplast / Greiner Type: CAL VAK 4P Year of manufacture: 1992 Machine number: K9209590 Total length: 6500 mm Vacuum pumps: 4 x Speck vacuum pumps (4.3 kW each) Water circulation pumps: 2 x Calpeda (1.1 kW each) Caterpillar haul-off, incl. attached saw Manufacturer: Uniplast / Greiner Type: CAT PUL 2D Hsdpfsyhcabsx Airew Year of manufacture: 1992 Machine number: R 9204546 Haul-off: Effective contact length: 2000 mm Pad width: 250 mm Haul-off force, max.: approx. 25000 N Speed range: approx. max. 10 m/min. Profile saw: HM circular saw blade: Ø 450 mm Profile cross-section, max.: approx. 300 x 100 mm Tilting table Manufacturer: Ide Type: ME N 52/2 Year of manufacture: 1994 Length: 6000 mm Support width: 270 mm Note: The complet profile line was overhauled in 2020 and has only been in operation for 325 hours since then.

Condition: good (used), Extrusion Line with Extruder & Co-Extruder. Sheet configuration B/A/B used for PP. Direct cooling unit (SMK) and SBI measuring unit newly installed in 2015. * Max. output: 1350 kg/h * Main screw output: 950 kg/h Hodon Utt Hepfx Airjw * Main screw: 180mm / 33D * Co-extrusion output: 400kg/h * Co-extruder scew: 120mm / 33D * Die width: 650mm * Roll stack: 3 * Winding unit for Jumbo rolls up to 1500kg This Extrusion Line is already disassembled and secured for transport (Location: Waalwijk, Netherlands).

Condition: used, Second hand line by TANG OG WEISS AS (DK) for packaging liquids into plastic bottles. Volume range from 50 ml to 750 ml. Working output of line: - for bottles volume 750 ml - up to 600 pcs/h - for bottles volume in range from 200 up to 400 ml - in range from 800 - 900 pcs/h, - for smaller volume bottles it is possible to assume a capacity in the range of 1000 to 1200 pcs/h. The line consists of: - Container of bottles produced by PACKFEEDER S.L. (Spain) model MN 100-4, - Filling-closing unit manufactured by TANG OG WEISS AS (DK) model TWKS. It includes filling module by TANG OG WEISS AS model TWRF, with two filling nozzles, stainless steel buffer tank with total volume 15 l, rotary table, caps feeder, arm for capping/cap tapping and plate conveyor, - Stainless steel lobe pump manufactured by SSP PUMPS (England) model L2-0017, for feeding the product to the buffer tank, - Labelling unit, by EME Etiketteringsmaskiner ApS. (Denmark) model 4-120 (4000 series) without printer, equipped with a plate conveyor, two pieces of self-adhesive label applicators (front and back of the packaging). Label feed height range: from 20 mm to 120 mm, label feed width range: from 10 mm to 250 mm, operating speed: 0-40 m/min, - Automatic packaging machine in heat-shrinkable film by SKINETTA PAC-SYSTEME GMBH & CO. (Germany) model ASK 450. The device wraps packages of 6 bottles with film and thermoform it. The entrance opening to the foil shrinking section has the following dimensions: width 440 mm, height 320 mm (year of manufacture 1994, no documentation), - Plate conveyors and control panels. Hjdpfxsyi Ezks Airsw The equipment includes a cabinet with formats for oval bottles with volumes: 50 ml, 200 ml, 400 ml, 750 ml, as well as manufacturer's documentation in Danish and a user manual in Polish. The line was produced in 2007.

Condition: excellent (used), functionality: fully functional, Good working condition washing line with Weima shredder WLK1500 and Rotajet dryer and 2 sink float tanks Output capacity 750kg p/h Hsdsz Azz Espfx Airow

Condition: used, BARMAG extrusion system consisting of: 1x extruder BARMAG KEP 200-26,3,3-S 1x transmission gear KNÖDLER FZ 6000 2_Z-ED 200 - NEW, year of manufacture 2016 1x drive motor SIEMENS 1GG6208 with external ventilation 470V, 468A, 206kw, 2600rpm, Err. 310V, 6.8A - NEW, year of manufacture 2015 1x control unit 1x dosing unit SCHOLZ incl. Feed hopper with level sensor - year of manufacture 2004 Hedpfxouak Nlo Airjw System features: - Single-screw extruder, year of manufacture ca. 1973 - Throughput 800kg/h - Conversion to new drive + gearbox in 2016 - Screw diameter 200mm - Screw length 5266mm - Process length 26.3D - Geometry: feed - barrier - mixing section - Screw material: nitrided steel - Technical documents Subject to prior sale Please send inquiries by email only Note: The machine is still installed and can be inspected on site. The buyer must dismantle it himself and organize shipping. This is not part of the offer price.

Condition: excellent (used), functionality: fully functional, Year of construction: 2023, operating hours: 200 h, machine/vehicle number: 230608, 4. Main Extruder Type: CWT95-Plus co-rotating twin-screw extruder; L/D 48 Machine Description: *IE5 AC 250 kW motor *Gearbox: Precise balancing principle applied to increase torque level; High safety factor design; Latest steel alloy material for gears, applied with special heat treatment and manufactured to a high level of precision; Imported NSK bearings and sealing rings; Special lubrication system combined with immersion and forced lubrication solutions; Latest generation plate heat exchanger configured for optimal cooling; Input/output rotation speed: 1480/600 rpm; Torque: 2x1990 N.M Oil pump: 1.5 kW With heat exchanger, flow meter, oil pressure gauge *Power Transmission: Compomac safety clutch torque limiter from Italy, with speed sensor *Extrusion Line: Screw diameter: 93 mm, L/D: 48:1; Maximum screw speed: 600 rpm; Screw configuration: modular structure, torque transmission via splines; Screw material: W6Mo5Cr4V2, surface hardness HRC58～64; Barrel configuration: modular structure, each barrel with a length of 4L/D; The inner surface of the linear material is made of α101, surface hardness is HRC62-64; Barrel No.1: Feeder for all possible components, No. 4 and No. 6 with a side feed port and a venting port. No. 8, 9, 11 with a suction port for degassing. The screw profile will be determined based on the requirement. Hsdezxxifopfx Airsw *2 side feeders for lateral feeding *1 set of degassing adapted to the needs Liquid ring pump, 1m3 water tank, gas and vapor recovery system *Electrical Cabinet Enclosure: Rittal Heat Exchanger: Apex Variable Frequency Drives: ABB PLC: Siemens Components: Schneider Electric *Spare Parts One set of screw and barrel elements and one set of shafts will be delivered with the machine.

Condition: used, Year of construction: 2021, functionality: fully functional, Sale of complete PVC profile extrusion lines We offer for sale 6 complete technological lines for the production of PVC profiles, originating from an operational production facility. The equipment dates from 2011–2025, with some units having undergone major overhauls. The technological lines include: • twin-screw conical extruder Pol-Service Majcher PSMD 65 / PSMD 65/132, • main motor power: 37 kW, • output: approximately 120 kg/h, • calibration table with 2 vacuum tanks (Pol-Service Majcher, Polreplast or Greiner – depending on the line), • caterpillar haul-off with guillotine (Greiner or Gruber Extrusion), • stacking device, • vibrating station for unloading Big-Bags. Hodpfxozlpabs Airow Key information • 6 complete technological lines, • main motor power: 37 kW, • output: approximately 120 kg/h, • equipment from reputable manufacturers: Pol-Service Majcher, Greiner, Polreplast, Rawotechnik and Gruber Extrusion, • selected equipment after major overhauls, • available technical documentation and CE documentation for selected machines. Purchase options: • single technological line, • several selected lines, • complete machine park, • the entire facility with all production equipment. The price quoted is for one line. A detailed list of equipment, technical parameters, technical documentation and additional photos are available upon request. Location: Lower Silesian Voivodeship, Poland.

Condition: new, Year of construction: 2026, SEM65/28 PVC Corrugated Pipe Extrusion Line Complete Production Line for Flexible Corrugated PVC Pipes Ø10–40 mm The SEM65/28 extrusion line is designed for continuous production of flexible corrugated PVC pipes. The line includes automatic material feeding, drying, extrusion, water-cooled pipe forming, automatic cutting and double-station winding. Equipped with Siemens PLC control and DELTA frequency inverters. Only one operator is required. 1. General Specifications * Model: SEM65/28 * Material: PVC * Capacity: 40–70 kg/h, depending on material * Pipe Diameters: Ø10, 16, 20, 25, 32, 40 mm * Wall Thickness: 1–2 mm * Production Speed: 5–30 m/min * Total Installed Power: 50 kW * Actual Power Consumption: Approx. 70–80% * Power Supply: 380 V, 3-phase, 50 Hz * Operating Direction: Right to left * Operators: 1 * Color: Grey * Installation Space: 11 × 2.5 × 3 m * Operating Temperature: +5°C to +40°C * Maximum Humidity: 85% 2. Equipment Included 1. ZJ300 Vacuum Auto Loader – 1 unit 2. STG-U100 Hopper Dryer – 1 unit 3. SEM65/28 Single-Screw Extruder – 1 set 4. Extrusion Die Head with Interchangeable Tooling – 1 set 5. Corrugated Pipe Forming Mold Blocks – 3 sets Ø10-40, Ø25-20, Ø16-32 6. High-Speed Corrugator – 1 unit 7. Automatic Double-Station Winder – 1 unit 3. SEM65/28 Single-Screw Extruder * Screw Diameter: 65 mm * L/D Ratio: 28:1 * Screw Speed: 0–40 rpm * Main Motor: 22 kW, asynchronous * Motor Control: DELTA vector inverter * Screw & Barrel: 38CrMoAlA, nitrided * Heating Zones: 4 * Heating Power: 3.2 kW × 4 * Heaters: Ceramic * Cooling Fans: 4 × 0.18 kW * Feed Throat Cooling: Water * Gearbox: SJF-173 * Gearbox Lubrication: Forced * Gear Material: 20CrMnTi steel * Capacity: 40–70 kg/h * Control: PLC 4. High-Speed Corrugated Pipe Forming Machine Water-cooled corrugator with an enlarged cooling area for efficient pipe forming. * Main Drive: 4 kW induction motor * Speed Control: DELTA inverter * Forming Plate Hardness: 63.4 HRC * Cooling: Water * Vertical Adjustment: Electric * Horizontal Adjustment: Manual * Adjustment Motor: 1.1 kW * Platform Travel: 800 mm * Forming Method: Pneumatic blow forming * Vacuum Pump: 4 kW Automatic Cutting System * Pneumatic inline cutter * Adjustable cutting length * PLC control 5. Automatic Double-Station Winder Hjdpfxjz Nkpwj Airjw * Type: Double-station * Drive: 12 N·m torque motor * Speed Control: Automatic synchronization * Traverse: Spindle speed tracking, frequency-controlled * Station Switching: Pneumatic self-locking * Air Pressure: 0.6–1 MPa 7. Wire device * Device for pulling a steel wire through corrugated PVC pipes during production, allowing easier cable installation 8. Applications Production of flexible PVC corrugated pipes for electrical cable protection, cable management, industrial installations and general-purpose conduit applications.

Year of construction: 2025, condition: new, functionality: fully functional, machine/vehicle number: 2846, Stock No. 2846 Demonstration line, Compounding Extruder Type Alphatec AD-.S 75 with: Segmented screws, co-rotating, intermeshing screw design Cylinder water/medium cooled/temperature-controlled Throughput up to 1200 kg/h - material-dependent Drive 250 kW - AC 48 L/D R+W safety gear coupling 3x degassing zones, 1x vacuum pump with condensate separator 2x side feeders type ZS-B Siemens Touch HMI control OPTIONAL: > Melt filter/screen changer > pelletizing systems: ST strand, WRG water ring, or UWG underwater pelletizing Hsdpfxsi Dtb Ae Airow > Screw configuration according to your requirements > Material dosing/blending : volumetric or gravimetric > Additional accessories Visit us at our Wuppertal plant. The system is ready for demonstration, test run date with your material after arrangement

Year of construction: 2014, condition: excellent (used), functionality: fully functional, RECYCLING PELLETIZING EXTRUSION LINE – BEIER 2014 / EKOCHEM – 2023 – with autostart heating - Belt conveyor with amperes load control - Agglomerator – 75 kw with cooling blower and auto water spray system - Main engine extruder – 110 kw - Double degassing MELT LASER FILTER SYSTEM – HOP 400 – Ekochem – 2023 - with autostart heating - with cooling pump - laser filter spare parts: 1 set 200 microns, 1 set 250 microns, 2 sets 300 microns, 2 blades PELLETIZER – RW-440 – Ekochem – 2023 - with new Ekochem die head water pump - with PE and PP die head Hsdpfouac Ugsx Airsw - with air compressor and custom die head blades – 48 h/set change - Centrifuges - Vibrator - Heated Silo + weight system - Capacity: PP( 400 – 500 kg/h) / PE( 500 – 600 kg/h )

Year of construction: 1996, condition: excellent (used), film width: 1,300 mm, Used single-layer blown film extruder for sale in excellent condition, featuring a 150 mm die diameter and a production capacity of up to 100 kg/h. Model: Queens EP-65N Processable materials: LLDPE/LDPE/MDPE/HDPE/other blends. Screw diameter: 65 mm Head: • Blown film die head • Die diameter: 150 mm Die gap: 1.2 mm Output: Up to 100 kg/h, depending on material composition • Maximum speed: 120 m/min • Winding width: 1300 mm Hedpfx Aisxrb Hmjrjw - Flying knife roll slitting Accessories included: • Tower • Gravimetric weight control system • Masterbatch dosing unit • Calibration cage The machine can be inspected in operation. Offered with spare parts.

Year of construction: 2026, condition: new, Extruder 30 mm - 28 l/d with die for weldingwire extrusion or profilextrusion with cooling bath Hodei Tu U Uopfx Airjw with adhesive water blow-off with haul-off with winder and guiding device

Condition: used, Year of construction: 2014, operating hours: 10,000 h, functionality: fully functional, machine/vehicle number: 1, total height: 3,000 mm, total width: 3,000 mm, total length: 40,000 mm, overall weight: 40,000 kg, type of input current: three-phase, input voltage: 360 V, year of last overhaul: 2026, transport length: 12,000 mm, noise level: 70 dB, protection type (IP code): IP46, transport width: 2,500 mm, Equipment: documentation/manual, 21-STAGE LINE FOR PET BOTTLE RECYCLING, INCLUDING SORTING, WASHING, CLEANING, DEGREASING, LABEL REMOVAL, SHREDDING, AND DRYING. Hsdpfjz Syplex Airsw

Condition: new, functionality: fully functional, Year of construction: 2022, Complete extrusion line for the production of PVC shrink film, specifically designed for sleeve-label applications. Built in 2022 by RL Plastproject (Italy), the machine is brand new, never installed, and immediately available. Technical Specifications: Product: PVC shrink film for sleeves Material: Rigid PVC dry blend Extruder: Single-screw with venting and gravimetric dosing Output: approx. 180–200 kg/h Film thickness: 40–80 micron Usable film width: up to 620 mm Die width: 900 mm Line speed: up to 60 m/min (depending on film) Cooling: Calender with chill roll Orientation: Transverse shrink forming unit Corona treater: Integrated Winding: Dual-position slitter-rewinder Control system: Siemens PLC with touchscreen HMI Hodpfx Aow Ahfgoirew Installed power: ~220 kW (to be confirmed) Air requirement: 6 bar Footprint: approx. 25 x 6 meters

Condition: good (used), Single Screw Screw diameter 25 mm Dimensions (LxWxH) 1860 x 900 x 1850 mm Options • Including haul-off • Including cooling bath Hsdpfovri Ddex Airew

Year of construction: 2012, condition: used, This Macchi 3-layer blown film co-extrusion line is designed for the production of high-quality polyethylene films with outputs of up to 800 kg/h. The line processes LDPE, LLDPE, MLDPE, and HDPE and is suitable for manufacturing collation shrink film, gusseted shrouds, stretch hood film, tubing, and sheeting. Materials to be processed: LLDPE/LDPE/LLD/HDPE Extruders: 65 mm + 80 mm + 65 mm Infrared heaters 3 pcs plate filters Head: 3-layer blown film die head TE5303-IBC-350/500 Die diameter: 350 and 400 mm IBC Die gap: 1.8 mm Output: Up to 800 kg/hour, depending on the material formulation Air ring: Dual-flow air ring, carbon fiber Take-off: Take-off unit, 2400 mm wide Oscillating nip rollers Motorized side gusseting Hedpfjzkru Eox Airjw Rewinder: Double winder, fully automatic back-to-back rewinder Winder, fully automatic roll change Reel diameter up to 800 mm Winding width 2350 mm Accessories: Tower Web guide, E&L Gravimetric weight control system, Piovan/Doteco Component blender, Shini Dosing units, Doteco Automatic thickness control, Kundig K-Design profile gauge control system Calibrating basket Corona treater, Martignoni Air shafts, 8 pcs

Year of construction: 1996, condition: reconditioned (used), No.: 2590k 1 used compounding-pelletizing line – output up to 1200 kg/h depending material, equipped with: 1x gravimetric ( loss-in-weight ) blending unit 5-Components SITECOM incl. control board 1x Extruder Twin-screw THEYSOHN Type TSK 90 Screws 2x Ø 90 mm – 36 LD co-rotating intermeshing Segmented screws-and Cylinder, Water / Medium cooled Extruder Motor 255 kW-DC / Screw speed up to 300 r.p.m. 1x Side feeding extruder TSD 75 twin-screw with 3 kW 3x venting ports 1x Melt-Filter Type K –HS- Y 176 mm incl. Hydraulic Pack 1x Melt-Pump with motor 22 kW 1x Strand die-head with holes 32 x Ø3,5 mm 1x Strand cooling bath 620 x 5000 mm 1x Strand pelletizer SG 300 with 11 kW Hsdpfx Aish Eyd Aersw ResoTec Monitor control Board Inspection visit / demonstration shortly possible - date on appointment You´re welcome. More compounding pelletizing lines ex pour workshop available, find our most-recent stock-list online on our homepage.

Condition: excellent (used), functionality: fully functional, machine/vehicle number: ZE60 A- Econ EUP 600, Stock- No.: 2858 1 used, partly overhauled and tested compounding-pelletizing line, consisting of: Berstorff ( Krauss Maffei ) compounding extruder Type ZE 60 A - 34 L/D twin-screw co-rotating extruder Extruder drive 160 kW AC Degassing with vacuum pump Laser separating head / melt filter Eprotec Melt x10 melt pump ECON EUP 600 underwater pelletizing system, complete with Start-up polymer diverter valve incl. hydraulic Water system, complete incl. pellet spin-dryer / centrifuge Control boards with Siemens Touch panel Hodpfjy At N Rjx Airew >> 12-month PLASTICO warranty OPTIONAL at extra cost: Material conveying Gravimetric loss-in-weight dosing-blending Granule classification Pellet filling station for Big Bags or Octabins Start-up in your factory by our Technicians We have more complete compounding extruders, pelletizing systems, loss-in-weight gravimetric blenders & more in Stock. Visit us in D 42329 Wuppertal or send us your inquiry, you´re welcome.