Used Platen for sale (530)

Condition: good (used), Complete used Tiflex textile screen printing setup for sale: a full manual screen printing line, ready to print t-shirts, sweatshirts, hoodies, polo shirts and garments with plastisol inks. Csdpfx Abs Agvmmehjhd This Tiflex screen printing equipment covers every step of the process: multi-colour printing on a 6-colour manual press, intermediate flash curing between colours, then final curing in an infrared conveyor dryer. A practical solution for textile decorators, garment printers, print shops, apparel brands and new screen printing workshops. 1. TIFLEX 2368000LC MANUAL SCREEN PRINTING PRESS (6 COLOUR, 6 STATION CAROUSEL) - Rotary manual press, 6 printheads and 6 stations - Maximum print area: 40 x 50 cm - Maximum outer screen frame size: 60 x 80 cm - Micro-registration with 3 knobs (X, Y and rotation) for accurate colour registration - Off-contact adjustment, screen/pallet parallelism and front/back pallet adjustment - Sliding pallets locked by ball plunger, rear screen clamping with anti-crush system - Pallet height: 86 cm, net weight: 200 kg - Fully manual, no electrical connection needed, dismantles for transport 2. 16 PALLETS INCLUDED (PLATENS) - 6 x men's XL pallets: 66 x 48 cm - 6 x women's M pallets: 50 x 32 cm - 2 x children's S pallets: 40 x 22 cm - 1 x sleeve pallet: 60 x 15 cm - 1 x sleeve pallet: 40 x 15 cm A complete pallet set for adult, youth and sleeve printing, with enough pallets to run all 6 stations in men's or women's sizes. 3. TIFLEX 40 x 40 CM INFRARED FLASH CURE UNIT (2008, VERY GOOD CONDITION) - Flash dryer for screen printing, 6 short-wave infrared emitters, 12 kW - Drying area: 40 x 40 cm - Drying timer and air-jet cooling timer - Automatic cycle start by contact rod when the pallet is detected - Half-power setting for delicate mesh - Height-adjustable stand on wheels - Three-phase 400 V, 18 A - Ideal for flashing a white underbase on dark garments before printing bright colours 4. TIFLEX T-IR 80 INFRARED CONVEYOR DRYER (2008, GOOD CONDITION) - Infrared textile dryer / drying tunnel for curing plastisol inks - Useful belt width: 80 cm, length under heating element: 130 cm - Teflon glass conveyor belt resistant to 250 °C - Variable belt speed, temperature controller with digital display - Movable shutters for thick items up to 12 cm (caps) - Fume extraction outlet, diameter 125 mm - Power: 4.8 kW, three-phase 400 V, 7 A - Overall dimensions: 270 x 131 x 130 cm, net weight: 265 kg LOCATION AND SHIPPING Equipment located in Bègles (Bordeaux area), France. Shipping across Europe and worldwide available on quotation. Tiflex screen printing machine, manual screen printing press, screen printing carousel, 6 colour 6 station press, textile screen printing equipment, t-shirt printing machine, garment printing, flash dryer, flash cure unit, infrared conveyor dryer, plastisol curing, screen printing pallets, used screen printing equipment.

Condition: excellent (used), Year of construction: 2014, operating hours: 60,720 h, machine/vehicle number: 227851, clamping force: 2,000 kN, screw diameter: 45 mm, clearance between the columns: 570 mm, injection weight: 291 g, mold height (min.): 250 mm, ejector force: 70,000 N, ejector stroke: 200 mm, MACHINE WITH DOCUMENTED PURCHASE EVALUATION I offer this used Arburg Allrounder 570 S 2000-800, manufactured in 05/2014, with Multilift Select (lateral) and protective housing. The redacted purchase evaluation is available as a separate PDF document. The previous owner placed great emphasis on the maintenance of the hydraulic system: Additional oil filtration operated around the clock to protect proportional and solenoid valves from contamination – ensuring reliable operation, high machine availability, and long-term value retention. TECHNICAL DATA Machine number: 227851 Type: hydraulic Clamping force: 2,000 kN / 200 t Control system: Selogica Injection unit: 800 Screw diameter: 45 mm Shot weight: 291 g PS according to seller's form Tie bar spacing: 570 x 570 mm Platen dimensions: 790 x 790 mm Minimum tool height: 250 mm Opening stroke: 900 mm according to seller's form Ejection stroke / force: 200 mm / 70 kN Operating hours according to current seller's form: 60,720 h Automatic cycle hours according to current seller's form: 54,616 h 400 V, 3~, 50 Hz; Total connected load according to nameplate: 105 kW HANDLING AND EQUIPMENT Multilift Select (lateral), 15 kg load capacity, No. 604575 X/Y/Z: 900/1,000/1,600 mm B- and C-axis pneumatic 4 x vacuum; 4 x dual-acting grippers Customer-side inputs and outputs Protective housing 12 hot runner zones 2 core pulls and 1 blow function Interfaces for chiller and dryer Variable speed pump, confirmed as IE2 by the seller Cedpfe Ahzy Rjx Abhohd DOCUMENTED MACHINE CONDITION Technical information from the seller's form, machine photos, and email from 04.11.2026. According to the seller, the machine was demonstrated in operating temperature. Technical documentation is available, according to the seller. No wear measurement of the screw, check valve, and cylinder is available. Dryer, chiller, and other peripherals are not confirmed as part of the scope of supply. Price on request. I would be happy to discuss availability, inspection, as well as delivery and payment terms with you personally.

Condition: used, Year of construction: 1933, functionality: fully functional, overall weight: 5,000 kg, total length: 4,000 mm, total height: 2,000 mm, total width: 2,000 mm, Lithographic press 55 x 75 cm. The machine is in very good mechanical condition, but will definitely require new rollers for printing. All spindles are present and some are still usable. Ideal machine for art studios or lithography workshops to produce high-quality lithographs. Very rare machine. Cedex D Tnajpfx Abhshd

Condition: ready for operation (used), Year of construction: 2015, clamping force: 900 kN, controller manufacturer: ENGEL, controller model: cc300, This 4-axis Engel Victory 200/90 tech + Viper 6 RC300 was manufactured in 2015. It features a clamping force of 90 tonnes and an injection unit size of 200. The machine includes a central ejector system and a magnetic clamping system for enhanced efficiency. If you are looking to get high-quality injection moulding capabilities, consider the Engel Victory 200/90 tech + Viper 6 RC300 hydraulic injection moulding machine we have for sale. Contact us for further details. ENGEL Victory 200/90 tech- Clamping Force: 90 tonnes - Injection Unit Size: 200 - Total Operating Hours (Machine): 15,903 h - Operating Hours in Automatic (Robot): 12,086 h - Clamping Platen Execution: Tie-bar-less standard platen according to EUROMAP - Centring Diameter: 125 mm EUROMAP - Magnetic Clamping System: Stäubli magnetic clamping plate - Ejector System: Central ejector with ejector safety interface - Heating System: 230 V ceramic cylinder heating bands ENGEL Viper 6 RC300- Maximum Manipulation Weight (Payload): 5 kg- Robot Axis Strokes: X-Stroke: 400 mm Y-Stroke (Single): 1,000 mm Z-Stroke: 2,360 mm C-Axis: Compact pneumatic rotary axis, 0–90° pivot, torque 6 Nm- Minimum Deposit Height: 1450 mm (center of unswiveled C-axis, without gripper head and part) - Max. Vertical Part / Gripper Head Size (TV): 200 mm - Maximum Total System Height: 4100 mm (handling and machine incl. machine shoes) - Part Deposit Side: Machine rear side - Entry Movement: Vertical Chedpfx Aj Af Tyzobhod

Condition: ready for operation (used), Year of construction: 2021, clamping force: 2,700 kN, overall weight: 10,700 kg, Vertical injection moulding machine manufactured in 2021. This Kloeckner Desma D 969.250 Z (S3) features a clamping force of 2700 kN and an injection volume of 500 cm³. The machine is equipped with a high-pressure injection unit and a touch-operated control system for process monitoring. If you are looking to get high-quality injection moulding capabilities, consider the Kloeckner Desma D 969.250 Z (S3) machine we have for sale. Contact us for further details. - Clamping Force: 2700 kN (300 US tons)- Injection Volume: 500 cm³- Injection Unit Type: B500HP (High Pressure)- Injection Pressure: 3500 bar- Nozzle Contact Force: 58 kN- Control System: 2030 TBM (Touch operation / process monitoring)- Operating System Status: Active 3,360 hours- Operating Hours (Hydraulic Motor): approx. 730 hours- Operating Hours (Hydraulic Pump - Clamping Force): 65 hours- Total Current: 138 A- Recommended Backup Fuse: 160 A- Supply Cable Cross-Section: 70 mm² Cu- Voltage: 3~400 V +N +PE- Frequency: 50 Hz- Max. Short-Circuit Current: 10 kA- Total Machine Weight: approx. 10.7 t (10,700 kg) (Clamping Unit + Hydraulic Unit: 9,700 kg; Injection Unit: 1,000 kg)- Footprint: 10 m²- Total Floor Load / Ceiling Load: 1,070 kg/m²- Foot Area / Floor Contact Area: 2,010 cm²- Specific Ceiling Load: 5.3 kg/cm²- Hydraulic Oil Tank Volume: 450/130 l- Temperature Control Medium Tank Volume: 2x7 l- Compressed Air Pressure: 6 bar- Compressed Air Flow: 0.5 m³/h- Cooling Water Flow: 1.6 m³/h- Cooling Water Inlet Temperature: max. 20 °C at 2.5 bar- Cooling Water Connection: 22-L- Pump Power / Rated Power: 22 kW (28.6 hp)- Pump Current Consumption: 32.0 A- Pump Pressure: 265 bar- Pump Flow Rate: 72/39 l/min- Maximum Mold Width: 560 mm- Maximum Mold Length: 780 mm- Platen / Stroke Dimensions: 600 mm stroke, platen distance 1480 mm, clamping stroke details 710 mm- Heating Plate Center Bore / Ring Size: Ø80 H9- Enclosure Type (UL): 1 Cjdpfx Abo Ad Inlshjhd

Condition: excellent (used), Year of construction: 2015, KRAUSSMAFFEI KM 1300-12000 MX + LRX 350 ROBOT Year of manufacture: 2015 | Clamping force: 1300 tons | Control: MC6 Codpfx Abe Af Ndqjhjhd Hydraulic injection molding machine KraussMaffei KM 1300-12000 MX from 2015, equipped with a KraussMaffei LRX 350 linear robot. The machine features a two-platen hydraulic-mechanical clamping system, an abrasion-resistant plastification unit, and an MC6 control system with a 19-inch touchscreen. TECHNICAL DATA 1. CLAMPING UNIT Clamping force: 13,000 kN / 1300 tons Clamping system: hydraulic-mechanical, two-platen Design: 4 tie bars and 4 adjusting units Mounting plate dimensions: 2210 × 1910 mm Tie bar spacing: 1570 × 1270 mm Opening stroke: 2350 mm Maximum platen opening: 3050 mm Minimum mold height: 700 mm Maximum mold height: 1400 mm Ejector stroke: 350 mm Ejector force: 250 / 125 kN 2. INJECTION UNIT Unit type: 12000 Screw diameter: 105 mm Injection volume: 5195 cm³ Injection shot weight (PS): 3689 g Maximum injection pressure: 2296 bar Maximum injection speed with accumulator: 150 mm/s Injection rate with accumulator: 1299 cm³/s Maximum screw speed: 144 rpm Plastification rate (PS): 130 g/s Abrasion-resistant plastification unit PV injection unit adjustment 3. KRAUSSMAFFEI LRX 350 LINEAR ROBOT Manufacturer: Krauss Maffei Model: LRX 350 Type: linear, servo-driven robot Payload: up to 35 kg Part removal on the side opposite the operator Range of motion: X-axis: 1200 mm Y-axis: 1000 / 1000 mm (telescopic) Z-axis: 3500 mm Drives for X, Y, Z axes: servo 4. CONTROL SYSTEM KraussMaffei MC6 19" color touchscreen Industrial computer Real-time Ethernet communication ProcessDesigner process visualization Machine diagnostics Adjustment and monitoring of injection parameters 5. HYDRAULIC AND ELECTRICAL SYSTEM Pump motor power: 132 kW Heater power: 75 kW Number of heating zones: 7 Oil tank capacity: 2440 l 6. DIMENSIONS AND WEIGHT Length: 13,650 mm Width: 3650 mm Height: 2820 mm Machine weight: approx. 70,000 kg / 70 tons

Condition: ready for operation (used), Year of construction: 2012, operating hours: 52,000 h, functionality: fully functional, clamping force: 13,000 kN, screw diameter: 95 mm, Clamping force 13000 kN Mould opening force, max. 910 kN Travel force movable platen opening 217 kN Travel force movable platen closing 153 kN Size of mould platens (h x v) 2210 x 1910 mm Distance between tie bars (h x v) 1570 x 1270 mm Mould opening stroke 2350 mm Mould height min/max 700/1400 mm Max. daylight 3050 mm Injection unit: Screw diameter 95 mm Ls/D ratio 23 Injection pressure 2173 bar Stroke volume 3721 ccm Shot weight (PS) 2642 gr. Injection rate 659 ccm/s Screw speed 150 1/min Plasticising rate max. 105 g/s Chsdpfx Ajz Hngyebhed Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 110 kW Installed heating capacity 59 kW Adjustable barrel heating zones 7 Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 13,00 x 4,00 x 3,00 m Total machine weight 64000 kg Max. mould weight 29000 kg Accessories: - Anti vibration pads - Sepro Robot 4050 S3 Trans Additional Options: - 3 x core pulls on movable plate - 3 x core pulls on fix plate - 2 x air valve - 6 x hydr. shot off nozzles - 16 x hotrunner controller - Robot interface according to Euromap 67

Year of construction: 1998, condition: used, functionality: fully functional, Automatic die cutter for paper and carton converting, processing sheets up to 1,040 x 740 mm at up to 8,000 sheets per hour. The press is equipped with an automatic waste stripping station and a pile delivery with manual non-stop rack and front waste removal device. Operation is controlled via the Bobst C.U.B.E. control system with an additional panel at the feeder, supported by Bernoulli sheet braking at the stripping station. Equipment ###Machine Platform with safety barrier Machine elevated by 415 mm, including platform elevation Centerline system for off-press tool preparation, quick registration, and fast setting of adjustable elements Electrical cabinet with air conditioner Light beam indicator for machine state Sheet passage control unit with infrared cells 4 auxiliary control panels C.U.B.E. centralized microprocessor control unit with LCD display and keyboard for sheet counting, cutting force with adjustable overload limiter, speed setting, and synoptic status display Additional C.U.B.E. control panel at the feeder Bernoulli sheet braking device at stripping station Three-phase asynchronous main motor with frequency converter control ###Feeder Floating pallet tray with manual handle for lateral adjustment during production Suction unit with multiple adjustments Pile height control with front photocell Side blowers laterally adjustable with Centerline marks Automatic vertical compensation of the suction head Manual non-stop device Sheet synchronization device adjustable during operation ###Feed Table Anti-static stainless steel plate Upper transport for paper, carton, and corrugated board up to 4 mm Upper frame with manual lifting device 4 fixed position lower feed belts 4 paired adjustable front lays Pull guide (OS) adjustable with Centerline marks Sheet presence control and double sheet detector Sheet synchronization device with manual adjustment, machine stopped ###Platen Press 3x upper chase with quick locking, fixed bottom plate Lower ground steel cutting plate, 5 mm Lower supporting plate of synthetic material, 22.5 mm Device for die-cutting without gripper margin Gripper bar reopening device Compensation plate, 4 mm ground steel Adjustable centerings for the lower supporting plate, ±0.9 mm ###Waste Stripping Station 2x upper pull-out frame 2x lower pull-out frame Central quick lock pull-out frame ###Technical Details Production Rate: 8,000 sheets/hour Max Sheet Size: 1,040 x 740 mm Min Sheet Size: 400 x 350 mm Max Die-Cutting Size: (with gripper margin) 1,040 x 725 mm Max Cutting Die Size: 1,050 x 746 mm Convertible Stock: Paper from 80 g/m², board up to 2,000 g/m², corrugated up to 4 mm Max Platen Pressure: 2.5 MN (250 t) Max Pile Height: Feeder 1,400 mm (non-stop 1,100 mm), delivery 1,120 mm Max Pallet Size: 1,200 x 800 mm ###Compressed Air min. 6 bar; without a central supply, a compressor of 7.5 m³/h with a 110 l tank is required ###Net Weight 15,000 kg ###Electricity Main motor 11 kW, total connected load max. 25 kVA Note Cjdpfx Abj Afvruohjhd The buyer is responsible for disassembly; no tools are provided. Still connected to power.

Condition: good (used), Year of construction: 2022, Brand: Dr. Boy GmbH & Co. KG Type: BOY 60E #55841 Year of manufacture: 2022 Operating hours: On request Cjdjz Tiwhspfx Abhjhd Screw diameter: 32 mm Maximum injection pressure: 2,142 bar Maximum shot volume: 100.5 cm³ Clamping force: 60 T Maximum distance between tie bars: 360 x 335 mm Minimum mold height: 250 mm Maximum distance between platens: 650 mm Electrical connection: 400 V / 50-60 Hz, 27.2 kVA Heating capacity: 8.4 kW Dimensions: 3,450 x 1,150 x 1,950 mm (L x W x H) Weight: 2,300 kg Options: • Procan ALPHA 4 control system, 15" full-touch display • TEC Package 1: wear-resistant screw and barrel, ceramic heaters • Interface package including OPC-UA, Euromap 77 & 82 • Cooling circuits (3x) on both platens + 8-way water distributor • Oil filling (EconFluid, ISO-32)

Condition: used, Year of construction: 2020, functionality: fully functional, clamping force: 2,500 kN, total width: 12,500 mm, total length: 11,500 mm, total height: 8,600 mm, power: 831 kW (1,129.84 HP), Equipment: documentation/manual, For sale is a highly automated BBM 2500 CoEx3 extrusion blow molding machine, manufactured in 2019. The machine is in very good technical condition, fully functional, and immediately available. An inspection while the machine is running can be arranged by appointment. The machine is designed for the economical production of large-volume HDPE hollow bodies and sophisticated technical blow-molded parts. It is a batch-type 3-layer extrusion blow molding machine with a parison accumulator head. The offered scope of supply includes: - Piovan GMS-160 high-performance plastic granulator, manufactured in 2023 - Piovan VM 500 extraction system Cedozw D Hajpfx Abhohd - GWK/Technotrans cooling unit The listed peripheral components are included in the offer price. If individual components or the entire range of accessories are not required, they can be removed from the scope of supply, and this will be taken into account when determining the price. Technical key data: Manufacturer/Model: BBM 2500 Year of manufacture: 2019 Process: CoEx3 extrusion blow molding with parison accumulator head Material: HDPE Design: 1 station with 1 CoEx3 blow head 3 extruders: 1 × 130 mm and 2 × 70 mm Total output: up to 1,200 kg/h Accumulator volume: 1 × 20 l and 2 × 7.5 l Electrical wall thickness control Clamping force: 2,500 kN Platen area: 2,160 × 2,400 mm Column spacing: 1,500 × 2,400 mm Opening width: 600–1,500 mm Electrical closing movement Locking via 6 hydraulic power strokes 2 integrated KUKA 6-axis robots for removal and handling Fully automatic KOCH material feeding system with gravimetric dosing and mixing Beckhoff TwinCAT control with Siemens components and drives Connected power: 831 kW Power supply: 400 V, 3 phases/N/PE, 50 Hz Dimensions: approx. 11,500 × 12,500 × 8,600 mm (L × W × H) CE documentation and machine manuals available The machine is particularly suitable for large-volume hollow bodies, technical molded parts, infrastructure products, sanitary parts and industrial containers. Availability: immediate Inspection and trial run: possible by prior appointment

Condition: good (used), Code: 0283 Brand: ITALPRESSE Model: 25/13 Fabricated platen for diathermic oil press Chedpfx Asyazdiebhed Technical data: Platen dimensions: mm 2500 x 1300 Max temperature up to 120° Max working pressure: 3/5 kg/cm2 Heating medium pressure 0,5 ate Composition: Aluminium - Flat gauged steel sheet - Coil of piping for fluid circulation - Reinforcement piping - Flat gauged steel sheet - Insulating material

Condition: ready for operation (used), Year of construction: 2015, operating hours: 29,446 h, clamping force: 2,600 kN, screw diameter: 60 mm, overall weight: 22,300 kg, controller manufacturer: ENGEL, controller model: CC300, product length (max.): 8,780 mm, Electrical injection moulding machine manufactured in 2015. This Engel e-victory 1640/260 features a clamping force of 2600 kN and an injection unit of 1640. It includes a tiebarless clamping system and a servo-electric injection system for high efficiency. If you are looking to get high-quality injection moulding capabilities, consider the Engel e-victory 1640/260 machine we have for sale. Contact us for further details. • Max swept volume cm³ 792 • Screw speed max r/min 250 • Injection rate cm³/s 765 • Spec. Injection pressure bar 2330 • Injection unit: 1640 • Injection system: Servo-electric, high execution • L/D ratio: 24 • Clamping system: Tiebarless ENGEL clamping system • Control unit: ENGEL CC300 (21.5" Full HD touchscreen) • Hydraulics: ECODRIVE SHV1 (1 demand-regulated servo pump) • Electrical connection: 3 x 400 V + N + PE, 50 Hz • Nominal connected load: approx. 164 kW • Centering: 160 mm • Hydraulic core pulls: 2 on moving platen, 2 on stationary platen • Vacuum/compressed air circuits: 8 on stationary platen with Venturi nozzles and pressure switches • Pneumatic mold valve control: 2-fold FESTO, up to 16 bar • Mold heating: 16 control zones, max heating power 25 kW • Nozzle radius: 15 mm • Nozzle bore: 4 mm • Nozzle contact stroke: approx. 405 mm • Hydraulic tank capacity: Main tank approx. 490 l, suction tank approx. 220 l • Robot interface: Euromap 67 / AN-146 • Additional equipment • MuCell package: • Complete MuCell Basic Package • PM cold-work steel screw Ø 60 mm • Hydraulic needle shut-off nozzle • Melt pressure sensor • Trexel auxiliary equipment: SII VC 30, MIK 1060 SII • Frame for two 50 L gas cylinders Chsdpfxoz Dgrpe Abhjd • Mold temperature control: 3 ENGEL flomo distributors (24 monitored circuits total) • Including GEKU robot

Condition: excellent (used), functionality: fully functional, Equipment: documentation/manual, SIMPLACUTTER (CAUHE) IV – 1680x1160 Machine lightly used, in very good condition, new upgraded electronics + laser protection Equipment: – pneumatic clutch and brake – control panel – new upgraded electronics + laser protection – 3 operating modes: single, continuous, delayed opening – central lubrication – additional safety guards Chsdpfxjz St Uzj Abhsd – operation tools – hardened pressure plate

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 616, type of input current: AC, input voltage: 240 V, compressed air connection: 6 bar, film width: 480 mm, input current: 16 A, For sale is an ILLIG HSA 50 C blister machine, manufactured in 1991. This is a high-performance, continuous-flow blister sealing machine with card feeder, suitable for film thicknesses of 150 µm to 400 µm (possibly higher, but not personally tested). The entire line is offered for sale (see pictures). Speed: 1–9 cycles/min with 4-up tooling. Example: fragrance dispenser, 4 units per blister tray = 2000 blisters/hour. Dimensions: approximately 9m x 1m x 2.25m. Sealing platen size: 57x32cm. The machine was 100% functional until it was dismantled and properly stored in our machine warehouse and was in operation until recently. Inspection of the dismantled system is possible on-site. An identical machine is still in operation on-site. A sample packaging can be installed for a test run to demonstrate the functionality. Location: Czech Republic (10 minutes past the Bavarian/Czech border from Furth im Wald). Codpfx Aoy Anifsbhohd

Condition: excellent (used), Year of construction: 2016, operating hours: 38,950 h, functionality: fully functional, clamping force: 1,600 kN, screw diameter: 25 mm, Clamping force 1600 kN Mould opening force, max. 240 kN Size of mould platens (h x v) 930 x 860 mm Distance between tie bars (h x v) 630 x 520 mm Mould opening stroke 450 mm Mould height min/max 300 / 550 mm Max. daylight 1000 mm Hydraulic ejector - stroke 150 mm Ejector force 22 kN Injection unit: Screw diameter 25 mm Ls/D ratio 26 Injection pressure 2500 bar Stroke volume 59 ccm Shot weight (PS) 53,7 gr. Injection rate 147 ccm/s Screw speed 477 1/min Plasticising rate max. 12 g/s Nozzle pressure 30 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 28 kW Installed heating capacity 8,1 kW Adjustable barrel heating zones 5 Dimensions and weights: Dimensions of the machine ca. 6,00 x 2,00 x 2,20 m Total machine weight 13200 kg Max. mould weight 1900 kg Accessories: - Anti vibration pads - Krauss Maffei Robot LRX 100 X: 550 mm Y: 1200 mm Z: 2000 mm C: 0 - 90 ° Additional Options: - 2 x Air valve - 5 x core pulls, Software only Cedoz N E Egspfx Abhehd - 12 x hotrunner controller - Robot interface according to Euromap 67

Condition: like new (used), functionality: fully functional, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 200 t, operating speed: 50 mm/s, table width: 1,300 mm, table length: 4,200 mm, ram plate width: 1,300 mm, ram plate length: 4,200 mm, distance table to ram: 300 mm, total length: 14,090 mm, total width: 2,600 mm, total height: 2,380 mm, overall weight: 13,000 kg, Equipment: 3rd hydraulic function, 4th hydraulic function, CE marking, The QIULIN BY624×14/20 industrial hydraulic press is designed for pressing and gluing flat components, veneer pressing, and the production of furniture and door elements. It features a single-platen design with two heating plates. The heating is electric, using thermal oil, with separate temperature control for the upper and lower plates. TECHNICAL SPECIFICATIONS – CATALOG DATA: – Brand: QIULIN – Model: BY624×14/20 – Country of origin: China – Type: hot hydraulic press – Pressing force: 2000 kN, 200-ton class – Number of working platens: 1 – Number of heating plates: 2 – Length of working plates: 4200 mm – Width of working plates: 1300 mm – Plate thickness: 52 mm – Maximum press opening: 300 mm – Unit pressure: 3.7 kgf/cm², approximately 0.36 MPa – Working temperature: from ambient temperature to 120°C – Total installed power: 79.35 kW – Plate closing speed: 50 mm/s – Heating: electric with thermal oil – Separate temperature adjustment for both plates – Automatic plate opening – Semi-automatic operation EQUIPMENT VISIBLE IN THE PHOTOS: – Robust frame construction – Hydraulic cylinder assembly – Hydraulic power unit – Separate control panel – Conveyor belt and table for material feeding and removal Cjdpfx Aboz Ix Auehohd CATALOG DIMENSIONS OF THE UNIT: – Length: 14,090 mm – Width: 2600 mm – Height: 2380 mm – Weight: approximately 13,000 kg Used machine, as shown in the photos. Paid transport can be arranged. Please contact us for details. JBS Woodworking Machinery WHERE CAN YOU SEE OUR MACHINES? JBS WOODWORKING MACHINERY WOLICA DRUGA 26 23-310 MODLIBORZYCE jbsmaszyny.pl

Condition: like new (used), Year of construction: 2019, clamping force: 500 kN, Equipment: documentation/manual, _ENGEL – Injection Moulding Machine Technical Data_ Serial number: 232665 Model: E‑VICTORY _Plasticising Unit 1_ • Screw diameter: 18 mm • Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed • Screw stroke: 80 mm • Maximum injection volume: 20 cm³ • Screw speed: 450 rpm • Screw torque: 75 Nm • Plasticising rate, 3-zone screw: 4.2 g/s _Injection Unit 1_ • Version: Standard • Injection rate: 83.97 cm³/s • Specific injection pressure, regenerative mode: 2,400 bar _Nozzle 1_ • Nozzle stroke: 210 mm • Nozzle contact force: 40.6 kN _Material Cylinder 1_ • Screw L/D ratio: 24 • Heating zones, including nozzle: 4 • Heating power: 5.1 kW • Note: maximum available equipment _Clamping Unit_ • Clamping force: 500 kN (approximately 50 tonnes) • Opening stroke + cylinder tolerance: 408 mm • Maximum distance between platens: 600 mm • Minimum mould height: 200 mm • Platen dimensions, horizontal × vertical: 500 × 450 mm • Drop-out chute width: 400 mm • Maximum mould weight on moving platen: 300 kg • Maximum mould weight on stationary platen: 300 kg • Maximum total mould weight: 600 kg • Dry-cycle stroke according to Euromap 6: 150 mm • Dry-cycle time according to Euromap 6: 1.60 s Mould weight notes: 1. Mould overhang according to mounting platens. 2. Less the weight of any rotary table. _Ejector 1_ • Ejector stroke: 100 mm • Ejector force: 39.8 kN _Drive Unit_ • Oil reservoir capacity – injection unit, main tank: 135 l • Oil reservoir capacity – clamping unit, auxiliary tank: 0 l _Machine Basics_ • Total weight without oil: 4.0 tonnes Chsdpfx Ajz Iyldsbhsd • Total connected power: 65.0 kW Transcription note: the small footnotes below the plasticising section specify reference materials and test conditions. They are not fully legible in this photo.

Condition: refurbished (used), Year of construction: 1986, functionality: fully functional, machine/vehicle number: 86053, total width: 1,950 mm, total length: 4,000 mm, total height: 1,800 mm, overall weight: 7,500 kg, type of input current: three-phase, input voltage: 380 V, working range: 48 mm, power: 9.56 kW (13.00 HP), control voltage: 24 V, paper weight (min.): 80 g/m², paper weight (max.): 2,000 g/m², paper width (min.): 350 mm, paper width (max.): 910 mm, paper height (min.): 290 mm, paper height (max.): 670 mm, Equipment: documentation/manual, lighting, Refurbished high quality flatbed die cutting machine from Italy with Spiess insert with steel insert plate with lateral adjustment, a left and right pull attachment (Spiess), double sheet detection, moving upper platen (WUPA system or Kama) with central pressure adjustment as with KAMA, but with the conventional intermittent pull gripper bar system with closing upper grippers. In other words: the sheet moves almost in a straight path through the machine; that is why this machine is ideally suited for lighter paper and cardboard types and is definitely an excellent intermediate step between a Heidelberg SBD and a medium format 40" die-cutting machine from Bobst, for example. No break-out, sheets are laid out directly on the pallet output after die-cutting. The output contains forks to place small format pallets on. Guaranteed pressure force is 200 tons. Stroke of the moving upper platen is 48 mm. Hardened die-cutting plate and device plate. This machine has hardly been used and is in excellent condition, however we have made modifications to further increase the ergonomics and operational reliability. Can be tested at our company and can be delivered with installation and warranty. The asking price is based on this. For all information in various languages, please open the PDF containing the original folder with explanation and specifications. Some specs: Maximum paper-cardboard size 67 x 91 cm Minimum paper-cardboard size 29 x 35 cm Gripper margin 6 to 14 mm Minimum paper weight approx. 80 -100 grs Maximum cardboard thickness 3 mm or 1.5 mm solid cardboard Stroke of the upper platen 48 mm Maximum rotation speed 4500 per hour Minimum rotation speed 1500 per hour Csdpfx Abjv Nwwaehohd Pressure force 200 tons Total power consumption incl. 80 m3 air pump 10 kW (13Hp) Total weight 7,500 kg The die-cutting section is transported separately from the Spiess insert and must be assembled. The electrical switch cabinet is fully plugged in with the components.

Condition: like new (used), Year of construction: 2010, operating hours: 24,600 h, functionality: fully functional, clamping force: 1,600 kN, screw diameter: 50 mm, clearance between the columns: 520 mm, mold height (min.): 300 mm, overall weight: 6,600 kg, Equipment: documentation/manual, Here we offer the following well-maintained used injection molding machine as part of our injection molding machine sales. We also purchase well-maintained injection molding machines, starting from the current model year 2010. We have been a wholesale supplier of used injection molding machines for over 25 years. Due to current circumstances - tax information and advantage for the used machine: From July 1, 2025, used machines can also be considered for tax purposes with a special depreciation of 30% per year. In addition to the lower price compared to a new machine, you can claim the same depreciation amounts as with a new machine. Keyword: Growth booster, (§ 7 paragraph 2 EStG-E) Codpfxoz A Iare Abhehd Manufacturer: KraussMaffei Type: KM 160-750 Control: MC5 Year of manufacture: 2008 / Delivered by KraussMaffei in 2010, as the original customer cancelled. Machine No.: 61011790 Operating hours: 24,600 h Injection unit Injection unit/screw: 50 mm Injection volume: 393 ccm Injection weight: 358 g Heating zones: 5 Nozzle stroke: 350 mm Injection pressure: 1892 bar Heating power: 16 kW Clamping unit Tie bar spacing: 520 x 520 mm Platen size: 820 x 845 (h x v) Clamping force: 160 tons / 1600 kN Opening stroke: 650 mm Maximum platen spacing: 950 mm Minimum mold height: 300 mm Ejector stroke: 150 mm Weight: 6,600 kg Pump motor: 22 kW Dimensions: approx. 4.90 m × 1.60 m × 2.10 m Extras -Machine shoes -Hydraulic screw back-rotation lock -Hydraulic screw drive with standard speed -Pneumatic valve 1 on the operator side for blowing function (1 piece 5/2-way valve with 1 solenoid coil). -Control optionally stroke/time or time/time. Quantity adjustable manually via 1 throttle valve at the valve outlet. -Nozzle protection door on the operator side, hinged -Ejector bay protection door on the operator side, hinged -Mechanical interface according to EUROMAP 18 for handling device on the fixed platen (with intermediate plate up to and including KM 500) -End position "rear" of the ejector and the tool ejector plate monitored in series -Chrome-plated tie bars in the clamping unit and injection unit -Media monitor in the pump room for oil pan monitoring -Enlarged oil cooler for a maximum water supply temperature of 31°C. -Hydraulic core pull control, 1-fold, on the operator side. -Water manifold, 8-fold -12 temperature control points for tool hot runner. Self-optimizing three-point PID controller of accuracy class 0.5. -Ejection of the cooled nozzle insert -Fan, control cabinet -Mains voltage supply: TN-C or TN-C-S or TN-S system (three-phase networks with separately routed neutral conductor or neutral conductor routed together with earth) -1 service socket, single-phase 10 A, in the control cabinet, connected before the main switch in country-specific design. -Signal interface according to EUROMAP 67 with reject signal and power supply socket CEE 16 A for handling device. -Event log for continuous recording and retrospective analysis -Quality monitoring package: process monitoring (cycle actual values and integrals) by specifying tolerance bands, actual value display, actual value storage. Documentation can be printed. -Z-cycle time analysis, cycle storage -Language: German, Greek Visible peripherals are not included in the scope of delivery. Free loading ex our warehouse in Hanover - worldwide delivery possible upon request. Inspection under power possible by appointment.

Condition: excellent (used), Year of construction: 2006, clamping force: 500 kN, screw diameter: 22 mm, clearance between the columns: 355 mm, overall weight: 2,700 kg, Clamping force: 50 t Year of manufacture: 2006 Injection unit .../200 Screw diameter: 22 mm Specific injection pressure: 2800 bar Injection volume: 41.8 ccm Mould clamping system 50/... Cedozt Ih Tjpfx Abhjhd Clamping force: 50 t Mould plate dimensions: 520 x 520 mm Tie bar clearance: 355 x 355 mm Mould height: 210 mm Opening stroke: 400 mm Maximum platen distance: 610 mm Weight: 2700 kg Dimensions (m) L x W x H: 3.8 x 1.1 x 2.1 m Control: NC4

Condition: used, Engraving press, working frame internal dimensions: 26 x 36 cm, working size: 28 x 38 cm, 4 rollers, ink tray. Chjdpfxjxy Ilre Abhed Machine is in good condition and available immediately. If interested, we are happy to inform you about additional machines in our inventory. You are warmly welcome to inspect the machine at our facility by prior appointment.

Year of construction: 2001, condition: used, functionality: fully functional, Bobst Autoplatine SP 104-ER (2001) Automatic die-cutting machine for paper and cardboard converting, processing sheets up to 1,040 x 740 mm at up to 8,000 sheets per hour. The machine is fully equipped with a waste stripping station and a blank stack delivery station with automatic non-stop operation and a pallet changing device. Operation is controlled via the Bobst C.U.B.E. control system, with an additional panel at the feeder, supported by Bernoulli sheet braking at the stripping and delivery stations. Equipment ### Machine Platform with safety barrier Centerline system for quick job changeovers Electronic sheet travel control Adjustable centering at stripping and delivery stations Control cabinet cooling unit Gripper bars Bobst C.U.B.E. electronic machine operating system Additional C.U.B.E. control panel at the feeder Bernoulli sheet braking device at the stripping station Bernoulli sheet braking device at the delivery station Motor with frequency converter control ### Feeder Pile tray with handle for lateral adjustment during production Pile height adjustment with front photocell Rear pile guides (OS and OOS) Side blowers adjustable with Centerline marks Suction unit with multiple adjustments Vertical adjustment of the suction head Automatic lateral pile correction Manual non-stop device Synchronization of sheet arrival against the front lays Safety system for lowering the pile tray ### Feed Table Anti-static stainless steel plate Sheet synchronization with machine stopped 4 front lays, adjustable in pairs, with front register control Pull guide (OS) with side register control Pull guide (OOS) with side register control Double sheet detector Feed belt slow-down device Support plates at platen entry Sheet hold-down device Upper frame with manual lifting device Upper transport for paper, paperboard, and corrugated board up to 4 mm 4 laterally guided transport belts ### Platen Press Gripper reopening device Die cutting without gripper margin Equipment centering and locking Locking of the chase against the upper beam Cutting force measurement with strain gauge Synthetic supporting plate, 22.5 mm 3x upper chase with quick locking, fixed bottom plate Compensating plate, 4 mm ground steel Adjustable supporting plate centering, ±0.9 mm Lowering of the chain guides ### Technical Details Production Rate: 8,000 sheets/hour Max Sheet Size: 1,040 x 740 mm Min Sheet Size: 400 x 350 mm Max Die-Cutting Size (with gripper margin): 1,040 x 725 mm Max Cutting Die Size: 1,050 x 746 mm Convertible Stock: Paper from 80 g/m², board up to 2,000 g/m², corrugated up to 4 mm Max Platen Pressure: 2.5 MN (250 t) Max Pile Height: Feeder 1,815 mm (non-stop 1,515 mm), delivery 1,430 mm Max Pallet Size: 1,200 x 800 mm ### Net Weight 20,000 kg Chods Afv Szopfx Abhed ### Electricity Main motor 11 kW, total connected load max. 25 kVA ### Note The buyer is responsible for disassembly; no tools are provided. Still connected to power.

Condition: excellent (used), Year of construction: 2017, clamping force: 3,000 kN, Equipment: documentation/manual, Clamping force: 300 t Screw diameter: 55 mm Shot weight: 510 g Distance between tie bars V: 720 mm Distance between tie bars H: 720 mm Platen size: 1040x1040 mm Shot volume: 558 cm3 Mould min: 400 mm Type: Horizontal Drive: Hydraulic Cjdpsz R Rggjfx Abhohd 2 core pullers Linear robot Tecnomatic compact conveyor

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: 61037303, clamping force: 1,600 kN, screw diameter: 55 mm, displacement volume: 475 cm³, injection pressure: 1,564 bar, injection weight: 432 g, mold height (min.): 500 mm, ejector force: 3,300 N, ejector stroke: 175 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 6,100 mm, total width: 1,710 mm, total height: 1,950 mm, overall weight: 8,400 kg, heating capacity: 8.9 kW (12.10 HP), drive type: Vollelektrisch, clear span: 520 mm, tool weight: 14,000 g, Injection molding machines directly from the manufacturer! As the manufacturer, KraussMaffei offers you our tested and versatile machines in stock: The fully electric PX series is the answer to your demands for greater flexibility combined with increasing productivity. Robust mechanics, highly precise and dynamic drive technologies, and intelligent energy management make the PX a reliable, productive, and efficient workhorse in any injection molding operation. An ergonomically optimized working height, maximum clearance under the mold, and excellent accessibility ensure maximum operator convenience. The PX series stands out due to its flexibility throughout its entire service life. TECHNICAL DATA: KM 160 / 750 PX G02 (Order 38621981) CONTROL  MC6 with 21.5" TFT color touchscreen and multi-touch function CLAMPING UNIT  Clamping force kN 1600  Mold opening force, max kN 240  Mold opening (h x v) mm 520 x 470  Platen size (h x v) mm 710 x 660  Mold height min. - max. mm 200 – 500  Opening stroke mm 850  Max. mold opening stroke mm 450  Ejector drive Hydraulic  Ejector stroke mm 175  Ejector force forward/backward kN 33 / 16  Ejector speed forward/backward mm/s 350 / 350  Max. mold weight kg 1400 INJECTION UNIT  Screw diameter / type mm 55 / Standard  Effective L/D ratio 21.3  Injection pressure bar 1564  Injection volume cm³ 475  Shot weight at max. stroke for PS g 432  Injection speed mm/s 125  Injection flow rate cm³/s 297  Screw drive / speed 1/min 267  Plasticizing rate (standard screw)4) g/s 75.8  Nozzle clamping force kN 42 ELECTRICAL PARAMETERS  Connected load kW 42  Installed heating power kW 18  Power supply V / Hz 415 / 50 Codpfj Afdatsx Abhehd WEIGHT AND DIMENSIONS  Net weight with control cabinet t 8.4  Length x width x height m 6.1 x 1.71 x 1.95 ADDITIONAL EQUIPMENT  Increased mold opening  Hydraulic core pull 1+1 - way  Pneumatic core pull 1+1 - way  Air valves 1+1 - way  Pneumatic cascade 4 - way  Euromap interfaces E18, E67, E77  Adaptive Process Control (APC) The machine is located in our factory in Parsdorf and is available for immediate delivery. Additional options can be offered upon request. We look forward to your inquiry.

Condition: good (used), Year of construction: 2013, operating hours: 22,420 h, functionality: fully functional, clamping force: 1,000 kN, screw diameter: 30 mm, displacement volume: 85 cm³, total length: 4,200 mm, total width: 2,100 mm, total height: 3,600 mm, overall weight: 7,300 kg, Equipment: documentation/manual, ARBURG Allrounder 1200 T 1000-170 Stock No.: 503459 Manufacturer: ARBURG Type: Allrounder 1200 T 1000-170 Control System: Selogica Year of Manufacture: 2013 Operating Hours: 22420 h Technical Data - Clamping Unit Cjdpfxjz A Dmze Abhjhd Clamping Force: 1000 kN Minimum Mold Height: 400 mm Maximum Mold Distance: 700 mm Opening Stroke: 300 mm Platen Size (Diameter): 1200 mm Ejector Stroke: 175 mm Ejector Force: 25 kN Centering of Moving Platen (Diameter): 125 mm Centering of Fixed Platen (Diameter): 125 mm Mold Weight: 1150 kg Technical Data - Injection Unit Screw Diameter: 30 mm Injection Volume: 85 cc Injection Pressure: 2000 bar Screw Length: 20 l/d Screw Stroke: 120 mm Number of Heating Zones: 4 Nozzle Distance: 210 mm Dimensions & Weight Machine Dimensions (L x W x H): 4.2 m x 2.1 m x 3.60 m Total Weight: 7300 kg Equipment 3x Temperature Control Units for Hot Runner Screen Text: German CEE Socket 16A Compact-Flash Drive Rotary Table Freely programmable inputs (2) and outputs (2) Machine with Material Hopper Machine with Water Manifold Needle Gate Nozzle, Hydraulically Actuated EUROMAP 67 Handling Interface Servo-Controlled Hydraulic Pumps Wear-Resistant Plasticizing Unit