Used Platen for sale (588)

Year of construction: 1999, condition: reconditioned (used), Machine is currently undergoing overhaul PROCESSABLE MATERIALS Depending on material properties and sheet configuration: · Paper with a minimum grammage of 80 gsm · Cardboard or solid board up to a grammage of 2,000 gsm · Corrugated board up to a total thickness of 4 mm (max. sheet curvature 4%) Hsdpfx Abjyuuzdetjt PERFORMANCE DATA Max. sheet format: 820 x 1,130 mm Min. sheet format: 350 x 400 mm Max. cutting force: (400 t) 4.0 MN Max. machine speed: 9,000 sheets/h Standard equipment of the machine: Feeder Non-stop high-performance sheet feeder W3 equipped with: • Automatic non-stop device • Automatic pallet changeover • Suction head • Double-sheet detector • Motorized stack side correction • Motorized suction head adjustment • Conveyor table with pneumatic cover frame • Compressed air and vacuum pump Register Table • Operator-side side lay, switchable between pull and push mode • Light sensor for accurate side alignment of sheets • Fine adjustment of the side lay • Two active front lays with light sensor for register control • Two inactive front lays for sheet stabilization • Separate fine adjustment of gripper edge for drive and operator side • LED display for accurate front and side lay registration • Trend display for sheet detection • Sheet rejection, disabling only the feeder • Height-adjustable top lay for positive sheet guidance Die-cutting station • Roller-guided support rails for the chase • Roller guide for die-cutting plate on swing-out support arms • Motorized die pressure adjustment • Automatic device for lifting the chase to the platen • Electronic die-cutting force display with max. pressure limitation • Vacuum device in sub-table for thin cutting plates Stripping Unit • Frame drive and frame lift for upper tool frame • Mount for the stripping board with centerline fine adjustment • Device for sample sheet removal • Upper tool frame • Lower tool frame Delivery • Fully automatic pile stacker, pre-selectable • Counted sub-stacks with automatic insertion of uncut sheets • Can form sub-stacks (interleaved sheets between 250 gsm – 800 gsm) • Frame lift for upper tool frame • Mount for change frames with electric adjustment in running direction • Pneumatic frame locking • Switchable gripper opener cam and sheet ejector • Sheet jogging device • Integrated conveyor belt for gripper edge or waste grid removal (double-cut) • Separator sheet magazine with electronic level control, refillable from B-side during production • Tool frame with centerline • Change frame for standard pile delivery / gripper edge removal • Change frame for blank separation grid • Mounting kit for separation punch • 8 x sheet hold-downs for standard pile delivery • 4 x cross support bars Options: • QTM – Patented guide rails • QTM – Chase with quick lock system and X/Y adjustment • QTM – Upper stripping frame with quick lock system • QTM – Upper delivery frame with quick lock system • Control upgrade to latest Siemens S7 controller • New generation frequency converters • Modem for remote service connection • Machine height increase: 900 mm

Condition: excellent (used), MEMBRANE PRESS For overlaying MDF shaped workpieces with PVC, PP and PET With VARIOPIN system Double Automatic front loading/unloading and preparation table (1500 x 2800 mm tray) Max pressure 2,400 KN Working pressure 320 BAR Dimensions of the Platens tables mm 1500 x 2800 Useful working dimensions mm 1250 (or 2 x 600) x 2550 Front loading side from mm 1500 (useful width mm 1250) Separate electrical cabinet and controls ( Electronic Programmer SIEMENS SIMATIC Panel Touch Hsdsrwxz Rspfx Abtjt Total Installed power KW 50 ca. OPTION: "Paternoster" reels Store (magazine) Unwinder (reels holder) with coating sheet cutting system

Condition: new, Industrial belt sander Scantool 150 x 2000 with integrated double dust extraction system Sanding belt: 150 x 2000 mm Working width: 150 mm Hsdpfeflt Aljx Abtjt Motor: 4.8 hp Speed: 34 m/s Table height: 475 to 1240 mm Sanding belt dimensions: 150 x 2000 mm Platen size: 530 mm Weight: 115 kg The Scantool industrial belt sander models with double dust extraction system, 75 x 2000 and 150 x 2000, are powerful, high-quality machines built according to the strictest environmental and safety regulations. The belt sanders are standardly equipped with a motor brake, adjustable working height, eye protection, angle stop, and motor protection switch with zero-voltage release. This low-noise machine with CE marking is ideally suited for sanding all metals. Motor protection switch with zero-voltage release Separate emergency stop Motor brake Adjustable angle stop Eye protection The infinitely adjustable working height enables an ergonomically correct working position. Perfect design for fast, effective, and safe sanding. Self-adjusting belt tension. Danish top quality.

Condition: new, Year of construction: 2026, The robust design also allows for the processing of longer workpieces. The grinding unit can be swivelled, making it suitable for use as an edge grinding machine. Large, balanced belt pulleys (225 mm) ensure low-vibration operation. Simple adjustment of the grinding belt. High belt speed of 17 m/s. Reversible rotation (right/left). Upper grinding platen with graphite coating. Grinding shoe with 4-point suspension. Equipped with a movable grinding shoe for grinding angled surfaces. Smooth-running work table, even under heavy loads from large workpieces. Optimal price-performance ratio. Additional ESE equipment: Standard with electric table height adjustment. Split table that can be folded out for special edge grinding applications. Drawer-type grinding attachment. Integrated work table lighting. Equipment details: Large, balanced belt pulleys (225 mm) ensure optimal and low-vibration operation. Belt speed: 17 m/s. Equipped with a swivelled professional grinding shoe for grinding angled surfaces. 4-point suspension. Hsdpjff Hdfjfx Abtet Standard with electric table height adjustment. Controls ergonomically arranged on a separate control panel. Standard with drawer-type grinding attachment. Split table that can be folded out for special edge grinding applications. Dimensions and weights: Length approx. 3750 mm Width/Depth approx. 1250 mm Height approx. 1730 mm Weight approx. 520 kg Dust extraction connection. Dust extraction port diameter: 160 / 160 mm Work table(s): Work table height adjustment: 550 mm Work table traverse: 690 mm Electrical data: Power of height adjustment motor: 0.37 kW Power of drive motor: 3.0 kW Connection voltage: 400 V Phase(s): 3 phases Type of current: AC Mains frequency: 50 Hz Grinding unit: Grinding belt length: 7000 mm Grinding belt width: 150 mm Belt speed(s): 17 m/s Grinding shoe length: 270 mm Grinding shoe width: 150 mm

Condition: used, SECOND- HAND BENDING PRESS FORGIARINI Hedpfswr Ah Ujx Abtot - Platens dim. mm. 1400X800 - Light 900 mm. - 2 cylinders mm. 100

Condition: good (used), Code: 0119 Brand: KOLMAG - ITALY Model: PGP 600 F Hydraulic press for moulds, frames, furniture elements, solid wood doors, plastic materials, composite materials and various Press modular structure with heavy thick plates without weldings and worked by tool machine Oleodinamic plant with pistons prefilling system in order to have a quick opening and closing of the platens Dimensions of massive steel platens mm 1600 x 500 - Thickness mm 60 with electric resistances - Max temperature 260°. N° 3 pistons diameter mm 240 Hodpfswk Ntzsx Abtot Pressure kg/cm2 56 Thrust Tonn 450 Safety photocells Hydraulic power unit Kw 7,5 Power absorbed heating platens 31 Kw Control board with pressure control gauge - Timer for platens opening - Telethermometer to regulate upper platen temperature - Telethermometer to regulate lower platen temperature - Switches for opening and closing of the platens - Emergency push button Overall dimensions mm 2250 x 1700 x 3300 h Weight kg 9000

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Double table machining center Working range X 2,590 mm Working range Y 2,260 mm Working range Z 400 mm Number of milling spindles 2 Liquid-cooled spindle Hodpfx Asuqw E Nobtst Main motor 19.2 kW Max rotational speed 24,000 rpm Aggregate heads 4 C-axis Tool clamping system HSK-F63 Tool change positions central magazine 24 Tool change on each head from 12 positions Boring heads vert. 20 (for each head) Horizontal boring heads X 8 Horizontal boring heads Y 8 Blade for grooves in X, in Y 2 Platens Number 4 360 m³/h vacuum pumps T Jet system for chip blowing Nesting Manual labeling Bar code reader Tool length measurement Software BIESSE BIESSEWORKS ADVANCED, BIESSE B_NEST Weight 17,900 kg

Condition: new, Year of construction: 2025, The EQPB BabyPress is a hydraulically operated benchtop model with CNC control. It is a robust and low-noise machine, specifically designed for the production of small parts. All manufacturing processes, from the hydraulic cylinder to the control cabinet construction, take place in-house. The advantages: - Basic design as a C-frame - Compact benchtop model - Ideal for prototypes and small series - Very short setup time - Functionally simple - Wide range of applications Standard basic design: - Upper slide guidance with high-precision roller guidance - Mechanical tool clamping system Promecam - Narrow table with individual V-tool holder (13x20) - CNC control Delem DA-41T - Y-axis CNC-controlled for programmed plunge depth calculation - X-axis CNC-controlled, 170 mm travel - R-axis manual - Low noise level - Low power consumption - Easy operation Technical data: - Press force 62 kN - Working length 285 mm - Clearance between the frames 230 mm - Installation height 215 mm - Overhang 70 mm - Ram stroke 100 mm Ram speeds: - Pressing stroke max. 9.8 mm/s - Retraction max. 50 mm/s - Motor power 0.7 kW - Main dimensions (W x H x D): 900 x 1,300 x 550 mm - Machine weight approx. 0.25 t - Tank capacity (hydraulic oil) 10 l Optionally, we also offer this machine without CNC control and/or with a press force of 12 t; please contact us for this. Hedoglkfpepfx Abtot

Condition: good (used), Year of construction: 1996, Engel ES 330H200V/125 HL – 2F Clamping force: 125 tons Tie bar diameter: 35 mm Tie bar diameter: 30 mm Injection volume: 158 cm³ 98 cm³ Hsdpfx Abelu Hkistst Year of manufacture: 1996 Enlarged clamping plate: 740 x 700 Minimum tool installation height: 350 mm Plus rotary platen

Year of construction: 2025, condition: new, Cost-effective single-column, microprocessor-controlled tensile testing machine for tensile, compression and bending tests up to 5kN Comfortable Windows software for universal test procedures, simple tests can also be performed without a PC. Made in Germany Basic equipment: • Machine with sensor (optionally between 50N and 5kN) • Accuracy class 0.5 • Windows based software • Warranty 2 years Optionally available: • Extensive gripping tools (mechanical, pneumatic and hydraulic), for example: compression platens Screw and wedge grip bending fixtures Special designs according to customer specifications • extensometer / strain gauge: Hodpfod H S Rrjx Abtet • Temperature and climatic chamber • Windows software PM-Soft-Smart for universal use, freely programmable • Commissioning into operation and training

Year of construction: 2025, condition: new, Economical two-column microprocessor-controlled tensile testing machine for tensile, compression and bending tests up to 10kN Comfortable Windows software for universal test procedures, simple tests can also be performed without a PC. Made in Germany Basic equipment: • Machine with sensor (optionally between 50N and 10kN) • Accuracy class 0.5 • Windows based software • Warranty 2 years Optionally available: • Extensive gripping tools (mechanical, pneumatic and hydraulic), for example: copression platens Screw and wedge grip bending fixtures Special designs according to customer specifications • extensometer / strain gauge: Long-distance strain gauge • Temperature and climatic chamber Hodpfsd H S R Ujx Abtst • W-Software PM-Soft-Smart for universal use, freely programmable • Commissioning and training

Condition: excellent (used), Year of construction: 2012, operating hours: 25,000 h, functionality: fully functional, clamping force: 8,500 kN, screw diameter: 95 mm, displacement volume: 3,367 cm³, Clamping force 8500 kN Mould opening force, max. 560 kN Travel force movable platen opening 89 kN Travel force movable platen closing 92 kN Size of mould platens (h x v) 1600 x 1600 mm Distance between tie bars (h x v) 1140 x 1140 mm Mould opening stroke 1600 mm Mould height min/max 500/1100 mm Max. daylight 2100 mm Hydraulic ejector - stroke 300 mm Ejector force 200/100 kN Injection unit: Screw diameter 95 mm Ls/D ratio 23 Injection pressure 1795 bar Stroke volume 3367 ccm Shot weight (PS) 3064 gr. Injection rate 690 ccm/s Screw speed 116 1/min Plasticising rate max. 104 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 53 kW Adjustable barrel heating zones 7 Oil Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 11,00 x 3,00 x 2,60 m Total machine weight 43000 kg Max. mould weight 12200 kg Accessories: - Anti vibration pads Additional Options: Hjdpfx Aboyb Sx Hotot - 1 x Air valve - 4 x hydr. core pulls - 12 x hydr. sequentional valves - 2 x 12 folds water flow regulator - Robot interface according to Euromap 67

Condition: ready for operation (used), Year of construction: 2012, operating hours: 70,936 h, clamping force: 4,200 kN, screw diameter: 80 mm, This Krauss Maffei 420 - 4300 CX hydraulic injection moulding machine was manufactured in 2012. It features a clamping force of 4200 kN and a platen size of 1200 mm x 1200 mm. The machine includes an injection unit with a screw diameter of 80 mm and an injection pressure of 2205 bar. Consider the opportunity to buy this Krauss Maffei 420 - 4300 CX hydraulic injection moulding machine. Contact us for further details. • Tie bar spacing (H x V): 800 x 800 mm • Platen dimensions (H x V): 1200 x 1200 mm • Mold installation height (min): 380 mm • Opening stroke: 1020 mm • Daylight (platen distance): 1400 mm • Max. mold weight: • Fixed side (DS): 3350 kg • Moving side (AS): 4460 kg • Total listed: 6700 kg • Ejector: Hedeyhby Hepfx Abtot • Stroke: 250 mm • Force: 95 kN • Retraction force: 48 kN • Pneumatic ejector: No • Core pulls: 2 on moving side (AS) + 2 on fixed side (DS) • Shut-off nozzle: 2-fold hydraulic cascade • Injection unit 1: • Type: SP 4300 • Screw diameter: 80 mm • Injection pressure: 2205 bar • Stroke volume: 1810 ccm • Shot weight (PS): 1647 g • Injection flow (PS): 498 g/s • Plasticizing flow: 106 g/s • Screw L/D: 22.5 • Nozzle radius: 12 mm • Armored injection unit: Yes Additional equipment • KM Linear robot, built in 2021 • Hot runner control, 12-zone • Mold sensors: Priamus (p=2 / t=0)

Condition: good (used), Year of construction: 2003, functionality: fully functional, Clamping force: 150 t. Clamping type: Toggle system. Tie-bar spacing: 470 × 470 mm. Platen size: 700 × 700 mm. Mold height (min–max, approx.): 180–500 mm. Opening stroke: 420 mm. Ejector stroke: 130 mm. Injection volume: 320 cm³. Screw diameter: 42/45 mm (to be confirmed). Heating zones: 4. Machine dimensions: 5000 × 1400 × 2000 mm. Machine weight: 6000–7000 kg. Hsdsx Hh U Njpfx Abtot

Condition: ready for operation (used), Year of construction: 2007, operating hours: 70,000 h, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 95 mm, displacement volume: 3,367 cm³, Clamping force 6500 kN Mould opening force, max. 346 kN Travel force movable platen opening 169 kN Travel force movable platen closing 144 kN Size of mould platens (h x v) 1520 x 1470 mm Distance between tie bars (h x v) 1000 x 930 mm Mould opening stroke 1150 mm Mould height min 600 mm Max. daylight 1750 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 96 mm Ls/D ratio 23 Injection pressure 1795 bar Stroke volume 3367 ccm Shot weight (PS) 3064 gr. Injection rate 690 ccm/s Screw speed 153 1/min Plasticising rate max. 104 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 50 kW Adjustable barrel heating zones 7 Dimensions and weights: Dimensions of the machine ca. 9,83 x 2,90 x 2,80 m Total machine weight 43170 kg Hodpfx Abex Hzzcetjt Accessories: - Anti vibration pads - Krauss Maffei Robot LR300 X: 1200 mm, servo Y: 1000/1000 mm, servo Z: 3500 mm, servo C: 0 - 90° - Conveyor - saftey guard Additional options: - 1 x air valve - 6 x pneumatic sequentional valves - 12 hotrunner controller - 2 x hydr. core pulls on movable plate - 2 x hydr. core pulls on fix plate

Condition: ready for operation (used), Year of construction: 2005, operating hours: 60,000 h, functionality: fully functional, clamping force: 9,500 kN, screw diameter: 105 mm, clearance between the columns: 1,400 mm, displacement volume: 4,546 cm³, injection pressure: 1,778 bar, injection weight: 4,137 g, Clamping force 950 kN Mould opening force, max. 665 kN Travel force movable platen opening 112 kN Travel force movable platen closing 117 kN Size of mould platens (h x v) 1960 x 1710 mm Distance between tie bars (h x v) 1400 x 1150 mm Mould opening stroke 1800 mm Mould height min/max 600/1200 mm Max. daylight 2400 mm Injection unit: Screw diameter 105 mm Ls/D ratio 23 Injection pressure 1778 bar Stroke volume 4546 ccm Shot weight (PS) 4137 gr. Injection rate 805 ccm/s Screw speed 126 1/min Hedpjx Hz I Nefx Abtst Plasticising rate max. 147 g/s Nozzle pressure 166 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 110 kW Installed heating capacity 59 kW Adjustable barrel heating zones 7 Reservoir capacity 1500 ltr. Dimensions and weights: Dimensions of the machine ca. 12,00 x 3,50 x 3,00 m Total machine weight 67000 kg Max. mould weight 20300 kg

Condition: used, machine/vehicle number: 17, functionality: fully functional, working width: 2,000 mm, opening width: 900 mm, SECOND-HAND PRESS PELLEGRINI - Platens dim. mm. 2000X800 - Opening mm. 900 - S/N 17 Hodpfex Rrgqsx Abtjt

Condition: ready for operation (used), Year of construction: 2017, operating hours: 235 h, clamping force: 3,500 kN, screw diameter: 70 mm, injection weight: 1,172 g, total width: 2,030 mm, total height: 2,350 mm, overall weight: 21,500 kg, product length (max.): 7,110 mm, This Milacron Elektron Evo 350 was manufactured in 2017. A robust electrical injection moulding machine featuring a screw diameter of 70 mm, closing force of 350 T, and a shot weight of 1172 g. It supports mold sizes between 249 – 800 mm and has minimal usage with only 235 testing hours. Contact us for more information about this machine. Machine Benefits Qualitative Machine Benefits • The machine is like new. Hsdpfjx D Iz Iex Abtjt Technical Machine Benefits • Injection unit size: 2290 • - Max. Injection Pressure: 1421 bar- Max. Stroke Volume: 1232 cm3- Max. Shot Weight (PS): 1172 g- Screw Stroke: 320 mm- Carriage Stroke: 400 mm- Nozzle Contact Force: 30 kN- Injection Rate: 580 cm3/s- Injection Speed: 150 mm/s- Screw Speed: 250 ot/min (RPM)- Plasticizing Rate (GPPS): 77 g/s- Effective Screw Length (L/D): 22.9 • - Number of Heating Zones: 4+1- Installed Heating Power: 39.6 kW • Clamping Force: 3500 kN:- Distance Between Tie Bars (H x V): 720 x 720 mm- Platen Dimensions (H x V): 1030 x 1030 mm- Mold Opening Stroke: 675 mm- Max. Daylight: 1475 mm- Min. Mold Mounting Height: 250 mm- Max. Mold Mounting Height: 800 mm- Max. Mold Weight (Moving / Stationary): 2630 / 1320 kg- Max. Total Mold Weight: 3950 kg- Ejector Force: 75 kN- Ejector Stroke: 200 mm Extra Information Machine still under power

Condition: ready for operation (used), Year of construction: 2006, operating hours: 98,495 h, functionality: fully functional, clamping force: 500 kN, screw diameter: 25 mm, clearance between the columns: 370 mm, displacement volume: 74 cm³, injection pressure: 2,500 bar, injection weight: 59 g, mold height (min.): 200 mm, ejector force: 22,600 N, ejector stroke: 100 mm, opening stroke: 600 mm, total length: 3,500 mm, total width: 1,400 mm, total height: 1,910 mm, overall weight: 3,000 kg, heating capacity: 8.12 kW (11.04 HP), pump power: 11,000 W, type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, Equipment: documentation/manual, We offer this used KraussMaffei 50-180 CX injection moulding machine, year 2006. KM Model: 50-180 CX International KM size designation: 180 CX/50 Year of manufacture: 2006 Machine serial number: 61009011 Machine weight: 3,000 kg Condition: ready for operation (used) Pump operating hours: 98,495 Automatic cycle hours: 83,046 Description: Screw diameter: 25 mm Clamping force: 500 kN Shot volume: 74 cm³ Maximum injection pressure: 2,500 bar Shot weight: 59 g Minimum mould height: 200 mm Maximum opening stroke: 600 mm Maximum daylight between platens: 600 mm Tie bar spacing: 370 mm Location ring, injection side: Ø125 mm Location ring, ejector side: Ø125 mm Ejector force (forward/backward): 22.6 kN / 9.9 kN Ejector stroke: 100 mm Machine dimensions (LxWxH): 3,500 x 1,400 x 1,910 mm Machine weight: 3,000 kg Hodpfx Aoyf E Dqsbtst Heating capacity: 8.12 kW Pump motor power: 11 kW Power supply: 400V, 50Hz, standard industrial three-phase connection Equipment: documentation included If you have any additional questions or need more information, please send us a message or call us.

Condition: ready for operation (used), Year of construction: 2001, operating hours: 98,780 h, clamping force: 2,000 kN, overall weight: 12,200 kg, controller manufacturer: ENGEL, controller model: CC100, This 3-axis Engel ES650H/200W-200HL-2F was manufactured in 2001. It features a clamping force of 2000 kN, a mold opening stroke of 700 mm, and a tie-bar distance of 920 x 750 mm. Equipped with dual injection units, screw diameters of 40 mm and 25 mm, and a rotary table control. Consider the opportunity to buy this Engel ES650H/200W-200HL-2F hydraulic injection moulding machine. Contact us for more information about this machine. • Clamping unit • Mold weight (WZ): 1500 kg • Total moving weight: 3000 kg • Minimum mold height: 550 mm • Mold opening stroke: 700 mm • Tie-bar distance (H × V): 920 × 750 mm • Platen size: 1250 mm • Ejector stroke: 150 mm • Ejector force: 61 kN • Centering ring diameter A-side: 110 mm • Centering ring diameter B-side: 90 mm • Mold locking system: Hydraulic / Pneumatic • Core pull control: Yes • Number of cores: 4 (A-side) • Rotary table control: Yes • Index plate control: Yes • Injection unit 1 (Main) – Type 650H • Max. shot volume: 200 cm³ • Stroke volume: 251 cm³ • Screw diameter: 40 mm • L/D ratio: 20 • Screw speed: 290 rpm • Injection pressure: 1930 bar • Injection rate: 142 g/s • Shot weight (PS): 216 g • Plasticizing rate: 26 g/s Hjdeyf H Nnepfx Abtst • Nozzle orifice: 15 mm • Pump motor: 30 / 12.3 kW • Injection unit 2 (Secondary) – Type 200W • Max. shot volume: 140 cm³ • Stroke volume: 69 cm³ • Screw diameter: 25 mm • L/D ratio: 24 • Screw speed: 480 rpm • Injection pressure: 2000 bar • Injection rate: 104 g/s • Shot weight (PS): 60 g • Plasticizing rate: 12 g/s • Nozzle orifice: 15 mm • Pump motor: ~6.8 kW • Machine axes travel • X-axis (injection unit): 500 mm • Y-axis (rotary table / mold carrier): 1000 mm • Z-axis (clamping unit): 1400 mm • Equipment and options (machine-integrated) • SPC / Process control: Yes • Pressure interface: Yes • Second injection barrel: Yes • Mold monitoring: No • Cavity pressure sensor: p-θ-t-θ (Priam) • Hot runner control: 16 zones • Filter dryer: No • Special programs: Yes • Special option: GealanXcomp • Automation: No • Condition • Well-maintained and serviced Additional equipment • Engel Linear Take-out Robot ERC 23/1-E (included)

Condition: excellent (used), Year of construction: 2007, Demag Concept 100/420-200 Year of manufacture: 2007 Injection Unit: Screw diameter: 25 mm Injection pressure: 2752 bar Shot volume: 61.3 cm³ Shot weight (PS): 54 g Max. dosing stroke: 125 mm Clamping Unit: Clamping force: 1000 kN Max. opening stroke: 500 mm Min. mould installation height: 250 mm Max. distance between platen: 750 mm Hedox Uqb Iepfx Abtjt Platen size: 600 x 600 mm Clear tie bar spacing: 420 x 420 mm Max. mould weight: 700 kg Equipment: Core pull: 2x Mould heating: 6x Air valve: 1x Robot interface Machine is supplied with robot

Condition: like new (used), Year of construction: 2008, operating hours: 6,200 h, functionality: fully functional, clamping force: 4,200 kN, screw diameter: 75 mm, Krauss-Maffei KM 420-2000 CX Hodpfowq D Efsx Abtot Krauss-Maffei injection molding machine, 420 tons of clamping force. Only 6,000 hours of automatic operation. Year of manufacture 2008. MC5 control. Screw diameter 75 mm. Extras: 8 hot runner zones. 2 cores on fixed platen, 2 cores on moving platen. 1 pneumatic valve on moving platen. The injection molding machine is delivered reconditioned by UK Transitus' expert technical team. We can offer commissioning at our clients' facilities, ensuring operation upon completion of the installation. Technical Details 75mm screw Injection pressure: 1635 bar Shot volume: 1237 cm3 Shot weight: 1126 g Maximum distance between plates: 1400 mm Minimum mold thickness: 380 mm Opening stroke: 1020 mm Distance between columns: 900 x 800 mm Plate dimensions: 1270 x 1230 mm 75mm screw Clamping force: 4200 kN Year of manufacture: 2008 Working hours: 6282

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, clamping force: 6,500 kN, screw diameter: 70 mm, injection pressure: 2,389 bar, ejector stroke: 135 mm, opening stroke: 1,825 mm, TECHNICAL DETAILS Clamping Unit Clamping force: 6,500 kN Maximum mold opening force: 346 kN Moving platen opening force: 169 kN Moving platen closing force: 144 kN Mounting platen (H x V): 1,520 x 1,470 mm Clear distance (H x V): 1,000 x 930 mm Mold opening stroke: 1,150 mm Minimum mold installation height: 675 mm Daylight: 1,825 mm Ejector stroke: 135 mm Ejector force forward/backward: 226 kN Injection Unit Screw diameter: 70 mm Hjdpfsycqc Tox Abtot L/D ratio: 23 Injection pressure: 2,389 bar Shot volume: 1,097 cm³ Shot weight (PS): 998 g Injection flow rate: 393 cm³/s Screw speed: 218 rpm Plasticizing rate: 83 g/s Nozzle contact force: 173 kN MACHINE DETAILS Dimensions & Weight Required floor space approx.: 8.70 x 2.90 x 2.80 m Total weight: 44,000 kg Electrohydraulic Equipment Rated power pump motor: 75 kW Installed heating capacity: 36 kW Temperature control zones cylinder heating: 7 EQUIPMENT Oscillating elements 1 x air valve 8-fold pneumatic cascade control Accumulators 2 x hydraulic core pulls at BWAP 2 x hydraulic core pulls at FWAP Robot interface according to EUROMAP 67

Condition: new, Special promotional price for in-stock items! While supplies last! Price ex warehouse, plus VAT. Belt sanding machine: Bernardo Type/Model: MS 150 x 2000 S-2 Condition: New Hsdpeb Hhh Dsfx Abtst Belt dimensions: 150 x 2000 mm Belt speed: 14.5 / 29 m/sec Contact wheel Ø x W: 200 / 155 mm Platen sanding table: 460 x 150 mm Dust extraction connection Ø: 100 mm Motor output S1 100%: 2.1 / 2.8 kW Motor input S6 40%: 2.8 / 3.6 kW Voltage: 400 V Length: 1080 mm Width: 520 mm Height: 1000 mm Weight approx.: 85 kg Features: - Standard with 2 speeds, ideal for sanding stainless steel - Universally applicable for sanding edges, surfaces and for round sanding - Graphite coating on the platen sanding surface increases the gliding properties of the sanding belt - Consistent belt tension thanks to spring-loaded tensioning device - User-friendly belt change, quick and easy - Good sanding performance thanks to high belt speed - Quick adjustment for horizontal and angled position - Universally applicable for crafts and industry - Large-sized platen sanding surface with protective cover - Including fine adjustment for parallel belt running Scope of delivery: - Sanding belt K 80 - Foldable protective disc - Sanding and support table - Workpiece stop - Dust extraction nozzle - Motor protection switch - Rubberized sanding roller - Graphite coating - Separate on/off switch - Base frame Promotional price ex warehouse Mindelheim, free on board. Art. 05-1249

Condition: ready for operation (used), Year of construction: 2006, operating hours: 50,000 h, functionality: fully functional, clamping force: 8,000 kN, screw diameter: 95 mm, displacement volume: 3,367 cm³, injection pressure: 1,795 bar, opening stroke: 2,100 mm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping force: 8,000 kN Max. mold opening force: 560 kN Moving platen opening force: 89 kN Moving platen closing force: 92 kN Mounting platen (h x v): 1,600 x 1,550 mm Clear daylight (h x v): 1,120 x 1,000 mm Mold opening stroke: 1,600 mm Min./max. mold installation height: 500 / 1,100 mm Max. mold weight: 12,200 kg Max. opening width: 2,100 mm Ejector stroke: 300 mm Ejector force forward/back: 200/100 kN Screw diameter: 95 mm L/D ratio: 23 Injection pressure: 1,795 bar Shot volume: 3,367 cm³ Shot weight (PS): 3,064 g Injection flow rate: 690 cm³/s Screw speed: 116 rpm Plasticizing rate: 104 g/s Nozzle contact force: 166 kN MACHINE DETAILS Dimensions & Weight Hjdsyv Acmopfx Abtst Space requirements (approx.): 11.00 x 3.00 x 2.60 m Total weight: 44,500 kg Pump motor rated power: 90 kW Installed heating power: 53 kW Barrel heating control zones: 7 Oil fill volume: 1,500 l Operating hours: 50,000 h EQUIPMENT Oscillating elements 1 x air valve Tie-bar pulling device 3 x hydraulic core pulls on moving side 2 x hydraulic core pulls on fixed side 20 x hot runner controllers Robot interface as per Euromap 67