Used Room Electromedicine for sale (883)

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, CLEANROOM - ISO 8 Guedpoq H H Rusfx Aa Soa | Cleanroom requirements ISO Class 8 | ISO Cleanroom Class 8 | Cleanroom classification. In order to achieve an ISO 8 air purity class in a Cleanroom, several levels of air filtration are usually used (e.g. G4 pre-filter, F9 filter, H13 final filter). Air movement in the room is non-unidirectional (there is a mixing of "clean" air supplied to the room with "dirty" air present in the room). Air vents in the ISO 8 room are placed on the walls. The required number of air exchanges per hour will depend on the nature of the activities conducted in the room and the number of personnel present, but the goal could be to provide 10-40 air exchanges/hr. In ISO Class 8, personnel are often present continuously. Employees may be dressed in standard work attire and visitors in a disposable apron. It is recommended to maintain a minimum overpressure of the room relative to the adjacent zone of 5-10 Pa. Requirements for equipment and materials intended for Clean Room with ISO air cleanliness class 8 (maximum average amount of particles released when: number of samples taken = 100; measurement performed in accordance with ISO 14644-14 in a cleanliness class at least one better than the purpose of the device; number of particles/m3) Detailed description in photos. Technical drawings attached to photos. Description of ventilation The purpose of the ventilation installation performed was to achieve the following air parameters in the Clean Room. The installation was made with the GBD PHARMA 2000 system, meeting all the requirements for 'clean rooms' in the highest classes of air purity. Parameters for the installation: a. Air purity - ISO 8. b. Temperature 19-23 st C c. Humidity max 38%. a. To ensure the required purity of the supplied air, an air handling unit manufactured by DOSPEL with a maximum capacity of V= 3500 m3/h [up to 15 air changes per hour] was used. The air handling unit is equipped with pocket filters : pre-filters FK EU5/EC2 and fine filters FK-EU9/EC2. In addition, HEPA 11 filters made by EUFILTER were used in diffusers located in the ceiling. Data sheets in point H6. As a result , with a measured flow rate of 3264 m3/h, an ISO 7 [class "C"] cleanliness class of the room was obtained in the resting state, and thus an ISO 8 [class "D" ] cleanliness class for the working state. b. The temperature range of 19-23 deg C is for the enlarged cooler and chiller to be freely maintained with 25% fresh air. c. In order to achieve in summer conditions with high temperatures of 30 deg C and humidity of 80%, a freon chiller of 31.4 kW and a chiller of 33.5 kW of cooling power were used. The chiller is made by FUJITSU supplied by Klimatherm Gdansk. The room is automatically regulated overpressure in relation to the external pressure - the pressure difference at the door : 15 Pa The automation of ventilation allows for "economical" mode , in which the installation works in a closed circuit and an overpressure of 15 Pa is maintained. Technical data attached to the photos.

Condition: excellent (used), Year of construction: 2013, operating hours: 20,900 h, functionality: fully functional, overall weight: 4,500 kg, power: 45 kW (61.18 HP), fuel tank capacity: 2,000 l, operating pressure: 10 bar, type of cooling: air, Complete compressor room Atlas Copco GA75VSD, built in 2013, 46,100 hours - 75 kW - Max. 10 bar Dimensions: L225 x W110 x H195 cm Godpjv Snn Iefx Aa Seua Atlas Copco GA45+, built in 2007, 21,000 hours - 45 kW - Max. 10 bar Dimensions: L205 x W100 x H180 cm Atlas Copco FD245, built in 2013, refrigeration dryer Dimensions: W120 x D110 x H100 cm Dimensions: 2000L tank, built in 2016, height 2.85 m Incl. oil-water separator System is currently still in operation; operating hours may vary. System is fully functional and regularly maintained. Maintenance kits and oils are included. Very good condition, see pictures. A forklift is available for loading. Pickup by appointment only in 75053 Gondelsheim. Shipping via freight forwarder is possible; please include your postal code in your inquiry.

Condition: used, Year of construction: 1988, x-travel 310 mm y-travel 340 mm z-travel 170 mm total power requirement 2,5 kW weight of the machine ca. 900 kg Gusdpfx Aajt Hxatj Sea dimensions of the machine ca. m

Condition: not inspected (used), functionality: unexamined, overall weight: 700 kg, total length: 1,000 mm, total width: 900 mm, total height: 1,600 mm, spindle speed (max.): 1,900 rpm, machine/vehicle number: 50025, No minimum price – guaranteed sale to the highest bidder! The machine is being auctioned due to a business closure. Placing a bid obligates you to collect the machine on time between 26.01.2026 and 29.01.2026! TECHNICAL DETAILS Spindle speed: 19 – 1,900 rpm Guedpfjxqmpdox Aa Sja MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,000 x 900 x 1,600 mm Weight: 700 kg

Condition: used, x-travel 800 mm y-travel 400 mm z-travel 300 mm digital readout Heidenhain table surface area 1000 x 520 mm turning speed range 40 x 2000 U/min spindle taper SK 40 total power requirement 2,2 kW weight of the machine ca. 2,2 t Gusdpfx Ajqpl Uuea Sja dimensions of the machine ca. 1700 x 1600 x 1800 m

Condition: used, Year of construction: 1976, x-travel 350 mm y-travel 150 mm z-travel 340 mm table surface area 600 x 210 mm spindle taper SK 40 spindle turning speed range 40 - 2000 U/min feeds 5 - 500 mm/min rapid traverse 1,2 m/min total power requirement 1,9 kW weight of the machine ca. 0,7 t - machine out of teaching shop - Accessories: solid table, vertical head with quill retraction, Gjdjwwwr Eepfx Aa Ssua DRO on 3 axis HEIDENHAIN, various tool fixtures, various collets, original DECKEL tool cabinet

Condition: used, Year of construction: 1989, x-travel 350 mm y-travel 200 mm z-travel 350 mm table surface area 700 x 280 mm spindle taper SK 40 150 - 1660 U/min feeds 25 - 285 mm/min rapid traverse 1 m/min quill stroke 80 mm milling-head swivable +/- 45 ° Gjdpfxsvzhids Aa Ssua total power requirement 3 kW weight of the machine ca. 1,2 t dimensions of machine L x W x H 1,27 x 1,1 x 1,65 m Accessories: vertical head with quill retraction, solid table, univ. table, rotary table 250 mmø, dividing unit with 3-jaw chuck 135 mmø, counter bearing, various tool fixtures, drill chuck, coolant

Condition: used, Year of construction: 1978, x-travel 300 mm y-travel 160 mm z-travel 340 mm table surface area 600 x 210 mm spindle taper SK 40 Gjdpewl N R Nofx Aa Seua spindle turning speed range 40 - 2000 U/min feeds 5 - 500 mm/min rapid traverse 1,2 m/min total power requirement 1,9 kW weight of the machine ca. 0,7 t - machine out of teaching shop - Accessories: solid table, vertical head with quill retraction, DRO on 3 axis HEIDENHAIN, counter bearing, various tool fixtures, various collets, original DECKEL tool cabinet

Condition: used, Year of construction: 1981, x-travel 800 mm y-travel 500 mm z-travel 460 mm table surface area 1000 x 500 mm spindle taper SK 40 control HEIDENHAIN TNC 150 spindle turning speed range 31,5 - 3150 U/min feeds longditudinal/cross/vertical 1 - 3000 mm/min rapid traverse longitudinal and cross 6 m/min Gsdpfx Aetqqplea Sjua rapid traverse vertical 4 m/min quill stroke 110 mm distance spindle nose and table max. 559 mm table load capacity max. 500 kg total power requirement 14 kW weight of the machine ca. 3,1 t dimensions of machine L x W x H 2,15 x 1,8 x 2,15 m Accessories: vertical head with hydr. tool clamping and quill retraction, solid table, coolant

Condition: used, Year of construction: 1973, x-travel 290 mm y-travel 170 mm z-travel 310 mm table surface area 600 x 215 mm spindle taper SK 40 spindle turning speed range 50 - 2500 U/min feeds 9 - 450 mm/min Godpotqqn Rsfx Aa Sjua quill stroke 70 mm total power requirement 1,8 kW weight of the machine ca. 860 kg dimensions of machine L x W x H 1,06 x 1,05 x 1,33 m Accessories: vertical head with quill retraction, solid table, counter bearing, coolant

Condition: used, Year of construction: 1999, x-travel 290 mm y-travel 170 mm z-travel 310 mm table surface area 600 x 210 mm spindle taper SK 40 spindle turning speed range 50 - 2600 U/min feeds 9 - 450 mm/min Gsdpewngkrofx Aa Ssua quill stroke 70 mm total power requirement 5,5 kW weight of the machine ca. 720 kg - machine out of teaching shop - Accessories: solid table, vertical head with quill retraction, DRO on 3 axis HEIDENHAIN, various tool fixtures, coolant

Condition: used, Year of construction: 2000, x-travel 600 mm y-travel 400 mm z-travel 400 mm table surface area 800 x 400 mm spindle taper SK 40 control HEIDENHAIN TNC 310 spindle turning speed range 10 - 3150 U/min spindle drive 5,5 kW feed - longitudinal/cross 1 - 5000 mm/min feeds vertical 0,5 - 2500 mm/min Godpjux Agisfx Aa Seua rapid traverse 6 / 6 / 3 m/min total power requirement 10 kVA weight of the machine ca. 2,5 t dimensions of machine L x W x H 2,16 x 1,70 x 2,0 m Accessories: solid table, vertical head with hydr. tool clamping and quill retraction, electron. handwheel, coolant

Condition: used, Year of construction: 1990, x-travel 600 mm y-travel 450 mm z-travel 450 mm control PHILIPS CNC 432 table surface area 740 x 440 mm spindle taper SK 40 Gujdpjtq I Hqefx Aa Sja spindle turning speed range 20 - 5000 U/min feeds 1 - 4000 mm/min rapid traverse 6 m/min quill stroke 80 mm toolpiece magazine: chain magazine 30 Pos tool diameter if 2 vacant positions max. 130 mm tool diametre at full load 100 mm tool length - max. 250 mm weight of tools max. 8 kg total power requirement 15 kVA weight of the machine ca. 3,8 t Accessories: vertical head with hydr. tool clamping and quil retraction, univ. table (manual), electron. handwheel, coolant

Condition: used, Year of construction: 1990, x-travel 600 mm y-travel 400 mm z-travel 420 mm control TNC 355 Heidenhain Main spindle: turning speed range - main spindle 20 - 4.000 min/-1 power capacity - main spindel 7 kW transmission ratio 3 tool taper SK 40 distance spindle /table 127 - 567 mm spindle diameter in front bearing 55 mm stroke of quill vertical 75 mm tool clamping 10 kN swivellable +/- 90 ° work table: table surface area 900 x 458 mm T-slots 7x 63 x 14H7 feeds: feed range 1 - 5.000 mm/min Feed force 5,4 kN rapid traverse ( X / Y / Z ) 7 / 7 / 6 m/min total power requirement 13 kW weight of the machine ca. 3,0 t dimensions of the machine ca. 4,0 x 4,0 x 2,1 m Gujdpfstqmm Aex Aa Ssa Tool Room Milling Machine - Universal HERMLE - UWF 900 E - Spindle-Head swivable +/- 90°

Condition: new, Year of construction: 2021, 585/600 mm 465/480 mm Gujdpewp Tiwjfx Aa Ssa 385/400 mm 900x500 mm 1200x250 mm 40-2000 U/min SK 40

Condition: new, Year of construction: 2023, 600 mm 500 mm 400 mm Gsdpfx Aaswp Tm Ao Sjua 1000x500 mm 1200x250 mm 40-3200 U/min DIN 2080 ISO 40

Condition: new, Product description: ROOMLINE powder coating booths are designed for paint recycling and prevention of environmental pollution during the powder coating process of large parts. Gsdpfx Aasggyige Seua It works on the principle of manual painting of products suspended on a rail or placed on a trolley.It is integrated into manual painting systems. Suitable for bar transfer systems. There are options to bring the products into the cabin with the trolley hanging above or on a bottom trolley. The cabin floor is left as the factory floor according to the demand, or the cabin is placed on a chassis and floor suction is provided. Available in floor, side wall or rear wall suction versions.The front of the cabin is optionally produced with a door or open. Depending on occupational safety and European standards, it can be equipped with equipment such as emergency exit door, fire extinguishing system, camera monitoring, ex-proof lighting and suction system, inverter motors. Cabinet construction consists of sandwich panels and steel structures in various thicknesses according to the project. Attachable Dust Collection Systems: - Jet-Pulse Filter System - Mono Cyclone - Multi Cyclone Advantages: - Easy to Use - Quick Color Change - Easy assembly and disassembly - Cleaner environment

Condition: new, ⭐⭐⭐⭐⭐ (5.0) ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Great Support! ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 8-10 weeks after receipt of payment! ✅Important note: If you would like to receive a quote for a blast cabinet, please use the blast cabinet configurator on the homepage of our website. ➖➖➖➖➖ ✳️Maintain your liquidity! We offer a variety of financing models to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ➖➖➖➖➖ ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ 💥 SR-LINE – Industrial blasting rooms for XXL applications 💥 🔧 Maximum performance, robust construction, sophisticated design! Whether railway wagons, construction machinery, aircraft, or military vehicles – with our SR-LINE blasting rooms, you can process even the largest and most complex workpieces reliably and efficiently! Our blasting rooms offer a safe, clean, and high-performance environment for every type of surface preparation – be it cleaning, roughening, or smoothing. _____ 🧩 Complete system with all essential components: ✅ Spacious main cabin with rubber lining to protect against wear ✅ Emergency exit doors with safety windows ✅ High-performance sandblasting pots in various sizes ✅ Pneumatic or mechanical abrasive recovery system ✅ Efficient dust collection system to maintain air quality ✅ Aftercooler, filter units, and robust steel construction ✅ Main control panel for centralized control ✅ Lighting system for perfect visibility in the room ✅ Optional: Overhead cranes, workpiece trolleys, wall-mounted multi-axis units for improved handling _____ ♻️ Economical & sustainable thanks to recovery system The used blasting abrasive is collected automatically or manually and returned to the cycle – saving resources made easy! _____ 🔒 Safety & comfort according to EU standards Our systems comply with applicable CE and safety standards and are equipped with optional sound insulation for a more pleasant working environment. 💨 Fresh air systems with fans or suction lines ensure optimal air supply during the blasting process. _____ 📦 What does the SR-LINE blasting system include? • Blasting cabinet • Workpiece entry door & operator door with panel • Interior lighting & rubber lining • Blasting pot & abrasive container • Recirculation system with scraper blades • Dust filter & aftercooler • Hoses, lines & main control panel • Robust support structure ⚠️ Compressor and compressed air tank must be purchased separately. A suitable air duct is recommended. _____ 🚀 Why SR-LINE? Guodpoghawmofx Aa Sea ✔️ Customized planning for your application ✔️ Extremely durable materials & components ✔️ Designed for high performance and continuous operation ✔️ Made by PROTON Maschinenbau GmbH – 40 years of experience _____ 📞 Contact us now for a customized quote – we'll be happy to advise you! 🛠️ SR-LINE – Your solution for large-format blasting technology. ☀️ 2-YEAR WARRANTY ☀️ ☀️ We have CE certificates for all our machines and ATEX certificates for the necessary machines.☀️

Condition: good (used), Year of construction: 1992, Travel X/Y/Z: 1000/500/500 mm Control: Heidenhain TNC 415 B Spindle: SK 40 Speed range: 0 - 5000 rpm Coolant device Godotmtvlspfx Aa Soua Universal milling head Can be swiveled and manually indexed via scale, can be swiveled away for horizontal machining

Condition: like new (used), functionality: fully functional, A cold storage room is offered, approximately 6 sq m without a refrigeration unit. Gjdpevzk Rwofx Aa Soua Length: 3.9 meters Width: 2.4 meters High: 2.05 meters

Condition: new, Year of construction: 2025, functionality: fully functional, Our SAPI Blasting Halls SAPI sandblasting halls and systems with 50 years of tradition and proven quality. Sandblasting halls are designed for industrial and commercial use, providing a safe environment for all types of blasting work. They include a blasting room, an abrasive recovery system with a filter and dust extraction system, lighting, and safety features to ensure the safety of the operator. Recovery System Our recovery system collects, separates, and reuses the abrasive material, which reduces costs and environmental impact. Ventilation and filtration systems ensure that the air in the hall remains clean. Adequate lighting ensures optimal visibility for the operator. Key Components of Our SAPI Sandblasting Halls: ✅ Blasting Room: The central area where the actual sandblasting takes place. 🌬️ Ventilation and Filtration Systems: Reduce dust levels and ensure optimal visibility. 🔄 SAPI Recovery System: Recycles the abrasive material and reduces costs and environmental impact. 💡 Lighting: Ensures optimal visibility for safe operation. 🦺 Safety Features: Emergency shutdown, fire protection, and protective gear like helmets, overalls, and gloves. ⚙️ Control Panel: The control center that integrates all electrical components. 🗑️ Dust Collection Container: Collects fine abrasive material for easy disposal. 🛠️ Compressor: Powerful compressor for the compressed air supply. 💪 Mammut Sandblasting System: Designed for tough industrial use. Reasons to Choose Our Sandblasting Halls: ✅ High Efficiency: Increases productivity and reduces operating costs. 🛡️ Safe and Clean Environment: Minimizes environmental impact and ensures a safe working environment. ⚙️ Customizable Solutions: Tailored solutions for optimal performance. 🔧 High-Quality Components: Durable components that reduce maintenance needs. 🛠️ Support and Service: Expert support for quick problem-solving. 🌱 Environmental Responsibility: Reduces waste and environmental impact. The SAPI Flat Conveyor System: The abrasive material is processed by our efficient abrasive cleaner, which separates contaminants. The system is low-maintenance, operates without interruption, and consumes very little energy. It is easy to retrofit and can be installed on existing hall floors with minimal foundation work. Advantages of Our Flat Conveyor System: ✅ Low installation depth, retrofit-compatible with existing blasting rooms 🔇 Low noise and friction ⚡ Very low energy consumption 🏗️ Very low wear, as only rubber is used 🚧 Very low installation height Gusdpoun R N Asfx Aa Ssa

Condition: used, Year of construction: 1980, x-travel:500 mm y-travel:500 mm z-travel:400 mm turning speed range:30 - 2240 U/min feeds -stepless-:1 - 750 mm/min rapid traverse:1500 mm/min table surface area:400 x 800 mm tool taper:SK 40 Gsdpfjcxxq Dox Aa Ssua total power requirement:7,8 kW weight of the machine ca.:1.8 t dimensions of the machine ca.:2,1 x 1,6 x 2,2 m

Condition: used, machine/vehicle number: 1621, x-travel:800 mm y-travel:300 mm z-travel:400 mm table-size:1000 x 440 mm Tool taper:SK40 spindle speeds:40 - 2000 U/min speed steps work spindle:18 spindle speed max.:( 6000 Possible by interchanging the Belt U/min feed range:10 - 500 mm/min feed steps:18 total power requirement:3 kW weight of the machine ca.:2,1 t dimensions of the machine ca.:1600x1550x1930 m The models FP3L has a tilting Spilndle Head can be swiveled 90° left or right direction for vertical and horizontal machining application. - With Rigid Angular Table: 1000 x 440 mm (6 nos of "T-Slots" with of 12mm width) Godeh Ra Nqopfx Aa Soua - With 2 Step Dial Configaration for Quick changing on Speed and Auto Feed - Quick Lever for rapid traverse movement on all axis - Universal Table , Separate power cabinet, and Chip tray

Condition: used, Year of construction: 1971, x-travel:450 mm y-travel:320 mm Godoiv Tf Hjpfx Aa Seua z-travel:450 mm table-size:950 x 300 mm spindle turning speed range:39-2320 U/min spindle taper:SK 40 power capacity - milling spindle:2,5 kW total power requirement:2,8 kW weight of the machine ca.:1,3 t dimensions of the machine ca.:1,4 x 1,3 x 1,8 m with vertical head, spindle quill, swivelling horizontal spindle, variable adjustable feed for all 3 axes, coolant device, machine light, chip pan, emergency cut-off

Condition: used, Year of construction: 1973, x-travel:815 mm y-travel:400 mm z-travel:410 mm quill stroke:130 mm turning speed range - stepless:67 - 2300 U/min :8 feed speeds:0,04 - 0,08 - 0,15 mm/min feeds of table:15 - 230 mm/min table surface area:1120 x 255 mm T-Slots:3 mm T-slot - width:16 mm T-slot - distance:63 mm Gedsvimrmepfx Aa Ssua distance spindle - column:260 mm ram adjustment:315 mm main drive motor:1,5 kW weight of the machine ca.:1,0 t dimensions of the machine ca.:1,75 x 1,80 x 2,10 m