Used Saw Machine for sale (66,426)

Condition: new, The SPECIAL 411 MS MACC is a semi-automatic band sawing machine for the cutting of solid bars and profiles of small dimensions, with high efficiency and excellent precision. The robust structure gives the machine the necessary rigidity and precision to the cutting unit. The belt drive is equipped with a two-speed motor and the special gearbox complete with gear is in bronze with the worm screw hardened and ground. The flywheels are suitably sized and the belt guides are sturdy and made with watertight invitation bearings and adjustable widia plates. The electromechanical microswitch control can be used to tension the belt with the rotation of the blade. Equipped with an accident prevention safety device on the flywheel cover and on the blade, the machine is completed by a swivel table to support the material and the vice with the rapid approach device. Functioning. Start the cutting cycle using the start button, the machine: 1. closes the vice and drives the belt motor 2. make the arch descend for the cut 3. the bow returns to the starting position 4. stop the belt motor 5. open the vice Possibility of manual cutting Cutting speed (m/min) 38-77 Cutting thickness (mm) 1.2 Kedefh R Tyspfx Abcslp Cutting range From 45 sx 60° dx Stop for cuts of the same size Adjustable Electropump for belt cooling 0.06 kW

Condition: new, Used MACC 320 MS Semi-automatic sawing machine Good New " CE " Kodpfx Abofibfaecelp Data sheet attached. Ready for delivery unless sold The basic characteristics of the machine (stiffness of the blade support, flywheel sizing, belt guides, belt tensioning) have been carefully studied to avoid the belt yielding, increase the duration, improve the linearity and the cutting time. Vertical rotation on pivot with adjustable conical bearings without backlash. Belt drive with two-speed motor and special reducer with bronze gear and hardened and ground worm screw. Appropriately sized flywheels. Sturdy belt guides with watertight bearings and adjustable widia plates. Tensioning of the band obtained by means of an electromechanical device with blade rotation microswitch control. Accident prevention safety device on the flywheel cover, on the control knob and on the blade. Cutting thickness 1,2 mm Cutting range from 0 to 60° right Adjustable stop for cuts of the same size 0.06 kW electric pump for belt cooling Operation: start of the cutting cycle by start button, the machine: 1. closes the vice and drives the band motor 2. lowers the arc for cutting 3. the bow returns to the starting position 4. stops the band motor 5. opens the vice Possibility of manual cutting ACCESSORIES ON REQUEST : SINGLE-PHASE motor 69 m/1′ Speed variator from

Condition: new, Semi-automatic band sawing machine for cutting solid bars and profiles of medium size with high efficiency and excellent cutting precision. The robust structure gives the machine the necessary rigidity and precision to the cutting unit. Belt drive with two-speed motor and special gearbox with bronze gear and hardened and ground worm screw. Suitably dimensioned flywheels Sturdy ribbon guides made with watertight invitation bearings and adjustable widia plates Belt tension obtained by means of an electromechanical device with microswitch blade rotation control Klsdpfx Abjfibd Tjcep Accident prevention safety device on the flywheel cover cover and on the blade Cutting thickness 1.5 mm Cutting range 60°sx 60°dx Adjustable stop for cuts of the same size Brush belt cleaning device Hydraulic power unit motor 0,37 kW 0.09 kW electric pump for belt refrigeration Jaw height 200 mm Clamp jaw length 185 mm Worktop height 760 mm Machine weight 820 kg

Condition: new, Semi-automatic band sawing machine for cutting solid bars and profiles of medium and large dimensions with high efficiency and excellent cutting precision. The robust structure gives the machine the necessary rigidity and precision to the cutting unit. Belt control with inverter driven motor and special gearbox with bronze gear and hardened and ground worm screw. Suitably dimensioned flywheels Sturdy ribbon guides made with watertight invitation bearings and adjustable widia plates Belt tension obtained by means of an electromechanical device with microswitch blade rotation control. Accident prevention safety device on the fly cover cover and on the blade Cutting thickness 1.5 mm Cutting range 60°sx 60°dx Brush belt cleaning device Hydraulic power unit motor 0,37 kW Klsdpfx Abjfh R Tuscop 0.09 kW electric pump for belt refrigeration Clamp jaw height 250 mm Jaw length 200 mm Worktop height 760 mm Machine weight 1250 kg 12260 N

Condition: new, Good brand new No. 1 available for immediate delivery! Warranty " CE " Made in Italy Cutting capacity : 0° = round tube mm 230 - square mm 220 - rectangle mm 170 x 300 45° = round tube mm 200 - square mm 180 - rectangle mm 180 x 230 60° = tubular round mm 130 - square mm 120 - rectangle mm 110 x 130 TECHNICAL DATA AND STANDARD EQUIPMENT: Vertical rotation on pivot with adjustable conical bearings without backlash. Belt drive with two-speed motor and special reducer with bronze gear and hardened and ground worm screw. Appropriately sized flywheels. Sturdy belt guides with watertight bearings and adjustable widia plates. Tensioning of the band obtained by means of an electromechanical device with blade rotation microswitch control. Vice with rapid locking device Kedpjfibfgsfx Abcolp Safety device on the flywheel cover, on the control knob and on the blade. Cutting thickness 1,2 mm Cutting range from 0 to 60° right Adjustable stop for cuts of the same size Low voltage system 24 V 0.06 kW electric pump for belt cooling The basic characteristics of the machine (rigidity of the blade support, flywheel sizing, belt guides, belt tensioning) have been carefully studied in order to avoid belt yielding, increase its life, improve linearity and cutting time.

Condition: new, The TITAN 43/20 CD+E firewood processor with joystick control cuts logs with a maximum diameter of ø 43 cm using a harvester bar and splits them with a splitting force of 20 tons. This is a combination machine (electric and PTO connection). Demonstration and inspection by appointment possible – the machine is currently in stock and available immediately. Warehouse clearance – special price – interim sale reserved. Kjdpfx Abstrmg Hjcslp

Condition: new, Year of construction: 2025, Technical Specifications Model: KMF10 Operated: Spring pressure Power: 10KVA (%50 DC) Welding Capacity: Up to 60mm mild steel strip Input Voltage: 220V (50Hz) Kledpfx Abjvmyalecsp Protection Fuse: 220V / 40A Welding Power Level: 5 Annealing Power Level: 5 Power Input Cable: 2,3m Protection Class: IP21 Dimensions (W/L/H): 160cm x 180cm x 79cm Weight: 294Kg

Year of construction: 1987, condition: not inspected (used), Sharpening machine for metal and segmental circular saws. Circular saw blade diameter from 80 - 710 mm. Kedjlmkpfjpfx Abcslp Any tooth pitch. Tooth height 1.2 - 14 mm. Working speed infinitely variable 15 - 180 teeth / min. Wet grinding device, NC controlled,

Year of construction: 1992, condition: used, Vollmer Saw blade shearing machine type NS 700 Kedjkmnyfopfx Abcolp Year 1992

Year of construction: 1994, condition: used, Double-end tenoner, edge processing machine, flush cutter, edge cutter, spindle motor, milling motor, saw unit, milling unit saw unit -Manufacturer: Paul OTT, saw unit from edge banding machine U 206 -Engines: Type K 14 -Power: 0.8 kW / 200 Hz -Speed: 1200 rpm -Saw blade: Ø 140 mm -Saw blade spacing: 515 to 1070 mm -Dimensions: 530/490/H600 mm Kjdpfx Abju Rv Ttocslp -Weight: 78 kg

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Circular saw in very good condition Ksdpfx Abot Uk Rmscelp

Condition: new, Year of construction: 2026, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability, is equipped with an automatic blade tension sensor. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Band speed 37.5/75 m/min Vice base height 900 mm Kjdpfoudi Unox Abcolp Weight 215 kg Angle 0º ø220 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100

Condition: excellent (used), HSS saws chamfering machine Peruzzi model SAUT 550, fully reconditioned and newly painted, like new Kedjhzcctjpfx Abcslp

Condition: used, Year of construction: 1994, Edging machine / Double edger EWD Esterer Model: DK90 TL 1000 Year of manufacture: 1994 Maximum feed width: 1000 mm Klodpfsyam Exox Abcsp Maximum cutting height: 120 mm Total of 3 saw blades 2 saw blades adjustable Measurement system: Combimes With S-type conveyor With cross-cut saw With infeed unit Esterer ARS TR With 2-strip chip separator Machine can be fully overhauled upon customer request! Already dismantled and ready for loading at any time Location: Austria, near Leoben

Condition: new, Year of construction: 2026, power: 4 kW (5.44 HP), input voltage: 400 V, type of input current: three-phase, total height: 34 mm, total length: 2,350 mm, total width: 1,250 mm, overall weight: 1,250 kg, table height: 600 mm, coolant pump power: 60 W, cutting range round steel at 90°: 400 mm, cutting range square steel at 90°: 400 mm, saw band length: 4,650 mm, saw band width: 1 mm, ROGI SAWING MACHINE TYPE WDS-400 SEMI-AUTOMATIC Saw blade size ----- 4650 x 34 x 1.1 mm Sawing speeds ----- 19/30/50/65/90 m/min. Motor power ----- 4 kW - 400V - 3 phase Weight ----- 1250 kg Cutting capacity ----- 400 mm / 500W x 400H mm INCLUDES Bimetal band saw blade Workpiece stop Saw blade guide with carbide inserts Hydraulic clamp Coolant pump Hydraulic downfeed cylinder Motor protection switch Automatic end stop Kljdpfx Aex N Iawjbcsp

Condition: as good as new (ex-display), Year of construction: 2023, functionality: fully functional, input voltage: 400 V, cutting range round steel at 45°: 450 mm, cutting range round steel at 90°: 450 mm, cutting range square steel at 45°: 420 mm, cutting range square steel at 90°: 450 mm, saw band length: 5,780 mm, saw band width: 41 mm, Semi-automatic sawing machine with 1-sided miter. (Also available with 2-sided miter.) Hydraulically operated material clamp. Hydraulically operated saw frame. Brand: KMS Type: KMY DG 450 Saw motor: 3 kW Height of support table: 888 mm Max / Min clamp opening: 0 / 740 mm Clamp height: 240 mm Mitre: 1 side Down speed: Continuously adjustable Cutting speed: Continuously adjustable, 20 - 90 m/min Band dimensions: 5780 x 41 x 1.3 mm Weight: ± 1600 kg Capacity: 90° (right angle): Round: Ø 450 mm Square: 450 x 450 mm Rectangle: 450 x 680 mm 60°: Round: Ø 450 mm Square: 450 x 450 mm Rectangle: 450 x 570 mm Kodpfevy Swisx Abcolp 45°: Round: Ø 450 mm Square: 420 x 420 mm Rectangle: 350 x 480 mm 30°: Round: Ø 350 mm Square: 330 x 330 mm Rectangle: 240 x 450 mm Incl. 2 short roller tracks. (not shown)

Condition: excellent (used), Year of construction: 1986, Used, good condition Klsdpfxowhgd So Abcsp Make: Altendorf Type F45 Year of manufacture: 1986 Machine No. 86-4-143 GS-tested Motor: 5.5 kW Carriage length: approx. 2500 mm Cutting width: approx. 800 mm Pivotable up to 45° Saw blade diameter: 450 mm Parallelogram guard Miter stop Extraction connection: D 80 and 120 mm Space required: approx. 2500 mm x 1600 mm x 1500 mm Weight: approx. 1000 kg Storage location: 54634 Bitburg, Germany, free on load, unpacked Sold in the current condition as seen, without warranty or guarantee

Condition: new, Year of construction: 2025, Martin Panel Saw T 77 - New Stock Machine - Top specification - Tiltable to both sides - Klodpsw D T Dkofx Abcep Equipment: T 7710/2-a Saw Unit Prex – tiltable to both sides T 7725/2-a Cutting height 205 mm T 7720/2-a Drive power 5.5 kW, stepless T 7730/4-a Table length 3.3 m T 7735/3-a Cutting width 1350 mm T 7743-a Electronically controlled parallel fence, lowerable in end position T 7755-a 3-axis scoring unit T 7757-a Scorer illumination Safe Light T 777572-a MITRE cutting system RadioCompens with continuous support T 7780/1-a Rear table extension 610 x 860 mm T 7792/2-a Sensor monitoring for laterally adjustable protection hood 2 x 45 degrees T 7704/2-a ConnectPad 12.9" / 13" T 7704/20-a OtterBox Defender Case T 7706/1-a ConnectApp at operator level Classic Location: ex stock 54634 Bitburg - available immediately -

Condition: used, Year of construction: 2009, Year: 2009 Kedpfx Absx Ruv Iecslp - technically efficient, ready to work – after full service - discs: 500 mm - working length: 3700 mm - PC control (Windows XP) - online access - vertical and horizontal pneumatic clamps - automatic disc guards - roller feeder - support for longer profiles

Condition: new, Band saw machine Make: OPTIMUM Model: S 275 NV Art.Nr.: 3300265 Condition: new machine Section (round): 225 mm Cutting speed: 20-90 m / min equipped as standard with: -Horizontal vise -Back fence - automatic shut-off after the end of the cut -Späneräumbürste Kjdpfsdynpcsx Abcjlp -Coolant system -Manual

Condition: like new (used), Year of construction: 2025, functionality: fully functional, We offer (refurbished) machines, spare parts, and accessories for the saw blade grinding machines of the following types by "Schmidt Tempo": ECE 45, EC 400, EC 500, ASG 1400, ASG 2000, G 400, ASG 400, AS 2-4, K 4. With our many years of experience, we can also support you with repairs of the above-mentioned machine types, including the supply of spare parts. We provide spindle overhauls for ECE 45, Freestyle, ASG 400, G400, ASG 1200-2000, S 630, AS 2-4, K4, or supply new grinding spindles for ECE 45 / Freestyle. Kedpfjguxgpjx Abcelp If you have specific requirements (machine / spare parts), please contact us by phone or email.

Condition: ready for operation (used), Year of construction: 1988, functionality: fully functional, We are selling the EMS 10 U machine, year 1988, no. 187. It is in good condition – see photos! The technical specifications can be found in the operating manual; please refer to the documents at the link below! The machine was used in our facility for frame saw blades. The original operating manual is included as well. Klodpfxeycfy Hj Abcop Please feel free to make us an offer! Pickup in 6858 Schwarzach.

Condition: good (used), Year of construction: 2016, operating hours: 3,000 h, Dinaco grinding machine, for sharpening band saw blades. The machine is refurbished, features automatic grinding wheel alignment, water cooling, and allows for grinding of vario tooth shapes. Klsdpfx Asx Tguhobcjp

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 0x0x0 mm Weight 29 kg Kodpfx Asv A Hhhsbcolp Total power requirement 0,25 kw

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1800x930x1500 mm Kljdsv A Hgqepfx Abcep Weight 700 kg Total power requirement 1,65 kw