Used Turret Rewinder for sale (1,947)

Condition: as good as new (ex-display), Year of construction: 2022, 450 Automatic Die Cut and Turret Rewinder 450mm Rotary Die Cutting unit: -Unwinder with auto web guider Bedjh Uctvopfx Aktjlp -Auto Tension Control system -Pressure meters for die cutting unit -Standard slitting unit with 6sets blades -Standard matrix removing system -Magnetic Powder system,mechanical speed 100meters/min -Max unwinding diameter 700mm, web width 330mm -Standard connection component to 330 turret rewinder 450 Auto Turret rewinder: -Automatic paper core bowl feeder -Automatic tail glue unit -Automatic paper core conveyor -Pressing paper swing arm -Automatic cut unit -Automatic finished roll ejection -Automatic brush press paper unit -Automatic core glue unit -Air expanding shaft 4sets each sizes 1’’, 1.5’’ and 3’’ -Labeling System (optional): Included Features: Speed: 60-100 m/min Max. Rewinding Diameter: 350mm Max. Web Width: 450mm Min. Rewinding Width: 40mm Total Power: 8KW Power Supply: 3PH+N+PE Air Source: 0.8MPa (As 40*30 products, 25m a small roll calculation: 3000m raw materials, average 30 minutes a roll of raw material. Every 25m a small roll and rewinding 6 rolls at the same time. 720 rolls can be produced in 10 minutes) Machine in stock in our showroom

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: Blsdpfx Ajyx Uy Ajktep • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Condition: good (used), Year of construction: 2019, functionality: limited functionality, machine/vehicle number: 377/2019, cutting width (max.): 1,000 mm, type of input current: three-phase, input current: 25 A, working width: 1,050 mm, input voltage: 380 V, input frequency: 50 Hz, Equipment: documentation/manual, TTR and hot foil slitter/rewinder. TTR1000 Material width: max 1050mm Max unwinding diameter: 700mm Max rewinding diameter: 150mm Max jumbo core length: 1100mm Rewinding shafts with tooling: 1 inch and 1/2 inch Slitting system: razor blade manual set 2 rewind turrets (upper and lower) for easy change Blodoz R Rdrspfx Aktop The machine is generally in good condition. It has tension control issues on one of the shafts, likely related to the magnetic powder clutch. The machine is still installed and ready for production, so we can arrange a live demo.

Condition: used, Year of construction: 1978, Year: 1978 – recently modernized TECHNICAL DATA: • Max. web width: 1450 mm • Max. unwind diameter: 1000 mm • Max. finished reel diameter: 400 mm • Hydraulic reel lifting • Circular slitting system • 4 Rewind shafts on two turrets • Pneumatic brake • Length measuring and control system • Optical edge control Blsdez Ern Sopfx Aktop Machine has been completely overhauled and equipped with new AC motors, a new cabinet and panels; new PLC Siemens S7; new Montalvo pneumatic brake and controls; new edge control for detecting edges from both the top and bottom.

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, STACK CMF BETA 2000 PRINTER 6-color flexographic stack printer Materials that can be printed: paper and plastic film Printing options: 6+0; 3+3; 4+2; 5+1 Maximum printing width: 1600 mm Maximum material width: 1660 mm Printing repeat: 330 to 1200 mm Production speed: up to 200 m/min Single unwinder Automatic turret rewinder Bedpfx Akez Rm Sqotelp Gas drying system Corona treater Various cylinders and anilox rollers included Year: 1997

Condition: good (used), Year of construction: 2019, Max. printing width 1500 mm Print repeat length (min. – max.) 400 – 850 mm Machine speed 500 m/min max Type of inks: Solvent based inks Material to be printed PP 10 um-200 µm BOPP 10 um-60 µm LDPE 20 um-200 µm CPP 20 um-70 µm HDPE 15 um-150 µm PET 12 um-50 µm OPA 15 um-50 µm Bodsvakdzjpfx Aktolp Machine power supply 400V Turret unwinder TAU-N 1000 Max reel diametr shaft 1 - 1000 mm Max reel diametr shaft 2 - 640 mm ( with max reel on shaft 1) Max reel diametr with 2 alike reels on shafts 1 and 2 – 810 mm Pneumatic dancing roller Turret rewinder TAR-N 1000 Max reel diametr shaft 1 - 1000 mm Max reel diametr shaft 2 - 510 mm ( with max reel on shaft 1) Max reel diametr with 2 alike reels on shafts 1 and 2 – 740 mm Pneumatic expansible shaft , I.D. 76 mm, 152 mm Antistatic bars ACE Blade slitting device Longitudinal blade slitting device, composed of 2 blades for side slits, complete with supports. Trim exhauster Noise-insulated trim exhaust device which consists of an electroblowing fan, Venturi pipe and trims collectio pipes with two exhausting nozzles. Edge guide OPG, electromechanical type, with single ultrasonic sensor, manually adjustable, to guide the edge of the web. Edge guide Kamberoller, electromechanical type, with single ultrasonic sensor, adjustable by motor Corona treating system Ferrarini&Benelli Reprint system, on the front or back side of the printed material Centralized manual (grease ) lubrication of CI drum bearings Hastelloy coated central drum Color unit opening: controls on external color units and internal color units Printing pressures adjustment The automatic system P2P allows to compensate the decrease of either the printing pressure and the colour density pressure, at machine speed increases Throw off( delayed impression release) Automatic, horizontal and activated by the same four motors moving the colour unit Printing units positioning Touch&Go It is a function which perfoms a sequence of “pre-defined” positions of the plate and anilox axis through the printing unit positioning system. Plate cylinders adjustment Tune&go It is an automatic tuning software which detects the best configuration for the adjustment of the plate cylinder, automatically modifying the control system according to the different types of plate. Pre-Register automatic print-to-print regiser pre-set “G” (Gearless) The term "Print-to-print register pre-set" is understood as the procedure used to position the printing plate cylinders on the press in phase one with the other as to achieve a printing register starting with a tolerance limit± 2 mm. Computer control The system is composed of an industrial computer equipped with a 19" SXGA TFT Single-touch IP65 L SVGA monitor Inking and washing system for anilox rolls and doctor blades Viscosimeter Gama G 26 Inks cooling and temperature control system with bank heat exchangers and regulation valves. Drying system Hot air gas burner with heating capacity up to approx. 150.000 Kcal/h ( BTU), composed of a burner installed inside the main air duct, complete with fan for combustion air, regulatory and safety devices. The exact heating capacity will be communicated during the completion of the machine. Infrared LEL monitoring system MSA Web Inpection Progress 500 Grafikontrol

Year of construction: 2008, condition: ready for operation (used), machine/vehicle number: LF 020, Min. / max. web width: 150 – 330 mm Min. / max. paper weight: 90 – 160 g/m² Bodpjy Shztofx Aktjlp Max. unwind roll diameter: 1000 mm Max. rewind roll diameter: 400 mm (300 mm when using the 3-shaft turret) Core diameter: Unwind: 76 mm / Rewind: 40, 45 and 76 mm (3 sets of 3 shafts) Max. speed: 200 m/min Description: Unwind with splicing tables and clamping devices, web guiding and tension control (including automatic web clamping during stop operation as well as dancer rollers), up to 12 rotary or 12 stationary knives within a pneumatically controlled slitting unit, edge trim extraction, interactive digital control panel with color touchscreen, program memory, settings management, counting functions (labels or running meters), and inspection control (missing label detection), fully automatic 3-shaft turret rewinder for non-stop operation. All required safety devices are installed on the machine.

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, GEARLESS FLEXOGRAPHIC PRINTING PRESS KOENIG & BAUER FLEXOTECNICA EVO XDN8 Flexographic printing press with a central cylinder Gearless 8 colors Maximum printing width: 1000 mm Maximum material width: 1050 mm Minimum/maximum print repeat: 330/750 mm Fully automatic turret unwinder and rewinder Maximum coil diameter: 1000 mm Gas drying system BST 100% camera system Viscometers FIFE web guide Blodszx Tuiepfx Aktop Year 2019

Condition: used, Year of construction: 1996, Technical Specifications: • Working width: 1050 mm • Unwind diameter: 1250 mm • Rewind diameter: 800 mm • Shaftless unwinder • Shear cutting system • Pneumatic knife holders • Fully automatic knife positioning Bljdpfx Aksz Erq Hetep • Turret rewinder with automatic roll removal • 3” friction shaft • Generator brake on unwinder • Unwind tension control via dancer roll system • Web edge control Equipment & Features: • Labeling device • Vacuum splicing table • Siemens S7 control system • Removal stand with push-off device • Automatic roll removal

Condition: used, Year of construction: 2000, The Carint central impression flexographic printing press is designed for printing on PE, PP, OPP, PET films, and paper. The machine features 6 printing units (6+0), a geared drive, and is suitable for a wide range of flexible packaging applications. Material width: 1,280 mm Printing width: 1,250 mm Print repeat: Min: 360 mm / Max: 1,040 mm Mechanical speed: Up to 300 m/min UNWINDER AND REWINDER The machine is equipped with a non-stop turret unwinder and a non-stop turret rewinder. Maximum reel diameter: 800 mm. Expanding shafts: 3" DRYING SYSTEM Electrical drying system. INK SUPPLY 6 pneumatic ink pumps. Bjdpfx Ajzku Nljktjlp ACCESSORIES • Motorized longitudinal register • Chamber doctor blade system • 8 Anilox cylinders • 6 Plate cylinders • Video inspection system • Web guides • Banana rollers • Plate cylinder lifting hoist • 2 electrical hoists • 2 cylinder storage racks with 6 cylinders of various repeat sizes

Condition: used, Year of construction: 2001, Number of printing units: 8 Web width: 1,270 mm Print width: 1,200 mm Print repeat: 300 - 1,000 mm Unwinder type: Double Axis Drop Splice Rewinder type: Turret Fully Automatic Splice Drying: Hot air – electric heaters Video camera: BST Euroscope Web guides: Yes Bedpfxox E Tm Us Aktelp Material: Plastic webs Camber doctor blades number: Yes Ink pumps: 8 Type of ink: Solvent based Transmission: Bull gear Length/Side registers: Motorized remote controlled

Year of construction: 2019, condition: good (used), LEMORAU MEBR+ 400 Digital Label Finishing & Die-Cutting Machine - 400 mm | Full Rotary & Semi-Rotary | Flexo Varnishing | Turret Rewinding | Approx. 700 Die Sheets Semi-rotary operation offers excellent flexibility for short runs and frequent job changes, while full rotary production enables considerably higher speeds for longer production runs. This particular machine features a comprehensive configuration, including two rotary flexographic spot-varnish units, corona treatment, web cleaning, turret rewinding, and the high-speed semi-rotary Speed Pack. An additional highlight is the extensive tooling package with approximately 700 die sheets, representing significant added value for the future owner. _____ MACHINE DETAILS Manufacturer: LEMORAU Model: MEBR+ 400 Year: 2019 Machine type: Digital Label Finishing & Die-Cutting Machine Maximum web width: 400 mm / 16" Operation: Full Rotary & Semi-Rotary Application: Digital and conventionally printed labels / self-adhesive materials _____ PRODUCTION SPEED Full Rotary Mode • Maximum speed for blank labels: 200 m/min • Maximum die-cutting speed in register: 120 m/min Semi-Rotary Mode • Standard semi-rotary speed: up to 40 m/min, depending on die / repeat • Equipped with Speed Pack • Semi-rotary production speed up to approximately 80 m/min, depending on application and tooling This combination makes the machine suitable for both short-run digital finishing and considerably longer production runs. Bsdpfx Akoz Ea I Tstolp _____ DIE-CUTTING SYSTEM The MEBR+ combines rotary and semi-rotary die-cutting in a single machine. Rotary Die Repeats 203.20 – 431.80 mm / 8 – 17" Semi-Rotary Die Repeats 41.30 – 371.00 mm / 1.6 – 14.6" The semi-rotary system significantly reduces tooling requirements for shorter jobs, while full rotary operation provides higher productivity for longer runs. Tooling Included A particularly important advantage of this machine is the extensive tooling package: Approx. 700 die sheets included This represents considerable additional value and can substantially reduce future tooling investment. _____ 2 x FLEXOGRAPHIC SPOT VARNISH UNITS The machine is equipped with: 2 x Rotary Flexographic Spot Varnish Units Suitable for: • Spot varnishing • Protective coatings • Decorative varnishes • Special label finishing applications • Additional surface enhancement The flexographic units considerably increase the versatility of the machine and allow additional finishing operations to be integrated directly into the production process. _____ CORONA TREATMENT The machine is equipped with a corona treatment system, providing improved surface treatment for demanding substrates. Particularly useful for: • Film materials • Synthetic substrates • Improved coating adhesion • Improved varnish adhesion _____ WEB CLEANING SYSTEM Integrated web cleaner for removing dust and contamination from the material before further processing. This can contribute to improved finishing quality and more consistent production results. _____ WEB GUIDING & TENSION CONTROL The MEBR+ offers sophisticated web handling technology.

Year of construction: 2022, condition: good (used), Manufacturer / Model: Grafotronic DCL2 550 Serial Number: 220520G Web Width: 550 mm Year of Manufacture: Location: Germany Condition: Used – in production CE Marking: Yes _____ Main Configuration Unwinder Module: • Max. roll Ø 1000 mm / weight 430 kg • Ultrasonic sensor and web guide ±15 mm • Splice table with clamps, servo brake, reel lift Flexo Printing / Coating Module (10–24" repeat): • GEW E2C UV dryer • Ceramic anilox 400 l/cm – 5.5 cm³/m² • Stainless steel ink pan 1.2 L, reverse-angle doctor blade • Re-register drive for overprinting • Max. speed 100 m/min – tolerance ±0.1 mm Die-Cutting Module (10–24" repeat): • Servo register system, anvil & support roller • Contact matrix rewind, stripping bar • Delam/Relam before die-cutting (limit 70 m/min) • Max. speed 250 m/min, tolerance ±0.1 mm Inspection & Slitting Section: • Missing Label Detection (MLD) up to 220 m/min • Automatic Sci-Fi knife system (12 sets) • Vacuum edge-trim removal • Auto-set under/back scorer (2 knives) Semi-Automatic Turret Rewinder: • 2 × Ø 600 mm rolls • Semi-automatic cutting and push-out system • Label & meter counters • Core diameters 40–76 mm Additional Equipment: • Anti-static brush • Tablet with housing and accessories • ERP interface • Crane for magnetic cylinders Bledpfxexq A Hlo Aktop Materials: • Foil 30–250 µm • Paper 100–250 µm _____ General Condition: Overall in good working order. According to the operator, two UV units require lamp replacement, which represents a minor cost. All other modules are fully functional.

Condition: like new (used), Year of construction: 2011, OMET Varyflex VF1 Year of manufacture: 2011 Web width: 850 mm Printing process: Flexo + Rotogravure combination line Condition: Used – very good condition Location: Europe _____ Machine Configuration • 8 x UV flexo printing units (equipped with new UV lamps, LED-ready) • All flexo units in ATEX execution (suitable for solvent-based inks) • 1 x rotogravure unit (compatible with solvent- and water-based inks) • 1 x die-cutting unit (530 mm) • In-line slitting system • Double turret rewinder • Turn bar (web turning system) • Hot air dryer on first printing unit • Cold seal trolley (movable) • Cold foil unit (cassette type, positionable on any unit) _____ Equipment & Tooling • Extensive anilox roller package • Sleeve system (well maintained) • Tooling in very good condition Optional (available upon request): • Omet plate mounter • Bimec slitter rewinder 1200 mm (almost new condition) _____ Technical Highlights & Advantages The OMET Varyflex VF1 is a highly versatile production platform designed for both label and flexible packaging applications. Key advantages: Blsdsyyn Hfepfx Aktop • Wide web format (850 mm) – ideal for high-volume production • Hybrid configuration (flexo + rotogravure) for maximum flexibility • ATEX design allows use of solvent-based inks • LED-ready UV system for future energy efficiency upgrades • Modular configuration with movable units (cold foil/cold seal) • Excellent condition with recently updated electronics (PLC, drives, control cabinets) • Proven application: previously used for polyethylene-coated materials (80–90 g/m²), ensuring reliability in demanding environments This machine offers an outstanding balance between performance and flexibility.

Condition: good (used), Year of construction: 1965, Revolver lathe, manufactured by HESTIKA, type HR32, year of manufacture approximately 1965. Maximum spindle bore: 32 mm, with tool turret, collet chuck. Spindle speeds: 200-3200 rpm, with coolant system. Machine documentation available. Collet chuck, size 164E. Bjdpfxjvgbphs Aktslp In good condition, ready for immediate use.

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, Stack Manzoni Printing Press Stack flexographic printing press with 6 colors. Brand: Manzoni. Materials that can be printed: plastic film and paper. Printing options: 6+0, 3+3, 4+2, 5+1. Maximum material width: 1300 mm. Maximum printing width: 1200 mm. Printing repeat length: 400 to 700 mm. Automatic unwinder and rewinder with turret system. Blsdozxdi Ropfx Aktop Automatic material control system: Rainbow 98P.

Condition: good (used), Year of construction: 1975, Revolver turret lathe, manufacturer: HESTIKA, type: HR42, year of manufacture: approx. 1975. Spindle bore max: 42 mm, with revolver head and Multifix tool holder, type: B. Spindle speeds: 88 - 2800 rpm, collet chuck, coolant system. Machine documentation available. Bedevgbqfspfx Aktslp Collet chuck for 173E collets. Machine in good condition.

Condition: good (used), Automatic cloth rewinder for offset printing machines Manufacturer: Vliesstoff Kasper Very good condition. 380V power supply, foot pedal control Device suitable for B1 and B2 format machines Blsdpsz R Ir Eofx Aktep

Year of construction: 2019, condition: used, The Lemorau MEBR+ is a digital finishing machine based on a modular concept, allowing modules to be added as needed to meet customer requirements. The MEBR+ operates in both full rotary and semi-rotary modes. The semi-rotary mode is suitable for short runs, while the full rotary mode is ideal for large runs at high speeds. Thanks to state-of-the-art servo technology, the registration tolerance remains consistent during acceleration and braking phases, as well as throughout the production process. The Lemorau MEBR+ is equipped with a servo-controlled compensation system that ensures excellent web tension control when the machine is running in semi-rotary mode. Standard equipment: - Maximum rotary speed 200 m/min (656 ft/min) – label stock - Maximum rotary speed 120 m/min (394 ft/min) – die-cutting for precise fit - Maximum semi-rotary speed 40 m/min (131 ft/min), depending on plate size – die-cutting for precise fit - Web width 250, 330, 400 mm (10, 13, 16 in) - Electronic counter (label/meter/roll counter as well as total meter and label counter) - Adjustable splicing table with pneumatic clamps - Electronic web guiding system with ultrasonic sensor for guiding opaque and transparent materials - Automatic web tension control via servo motors – constant and decreasing tension - Memory for 250 jobs for easy and quick job setup - 6 sets of round knives with lateral adjustment - 2 interchangeable pneumatic unwinders with a diameter of 25, 40 and 76 mm (1, 1.5, 3 in) - Detection of paper and liner tears - Rewinding on label entry/label exit - Remote support via internet connection - Automatic stop at the end of the master roll with programmable roll-end function - Semi-automatic rewinding - Foot pedal for step-by-step machine control - Multilingual touchscreen - Die-cutting repeats 203.20 – 431.80 mm (8 – 17 in) – rotary mode - Die-cutting repeats 41.30–371.00 mm (1.6–14.6 in) – semi-rotary mode - Maximum rewind diameter: 600 mm (23.7 in) with 1 shaft / 350 mm (13.8 in) with 2 shafts - Maximum unwind diameter: 700 mm (27.5 in) Bledpfx Aezqnxtsktep - CE conformity certificate Optional equipment: 1 Anti-static bar 1 “Clear-on-Clear” sensor 1 Corona treatment 1 Speed package (80 m/min in semi-rotary mode) 1 Turret unwinder 2 Flexo unit for spot coating with rotating register 1 Web cleaner QRC (Quick Remote Connection) 1 new die-cutting forme with repeat lengths of 41.30–371.00 mm (1.6–14.6 in) – semi-rotary mode approx. 700 die-cutting sheets

Condition: good (used), Year of construction: 1994, functionality: fully functional, turning height: 1,200 mm, workpiece weight (max.): 12,000 kg, turning diameter: 2,000 mm, rotary table diameter: 1,600 mm, rotational speed (max.): 315 rpm, torque: 25,796 Nm, spindle speed (max.): 3,000 rpm, table diameter: 1,600 mm, travel distance X-axis: 1,000 mm, workpiece diameter (max.): 2,000 mm, DÖRRIES VCE 2000 / 160 MC CNC Vertical Borer. CNC Vertical Borer with Live Drilling and Milling spindle. Table diameter 1.600 mm. Turning diameter 2.000 mm. C-axes 360.000 degrees. Built 1994. Bedpfo Ahkhmsx Aktolp ATC, chain for 30 SK 50 tools. With tool measurement. Cooling through Spindle. Hydrostatic bearing on cross rail and support. With Universal Anglehead, 360° turning, +15°/105° tilting.

Condition: used, functionality: fully functional, We are selling this machine. It is connected and can be tested. A video of the machine can be sent via the WhatsApp application. Documentation for the machine is available. Bljdpfx Akoydqfdotep Speeds: 1st range: 0.35-3.5 rpm 2nd range: 1.4-14 rpm Drive: 2 regulating motors, each with 120 kW, powered by a 240 kW Ward-Leonard converter. Diameter of the clamping plate: 8,000 mm Largest turning diameter: 12,500 mm Turning height: 2,200 mm The machine underwent a major overhaul and modernization in 1991. Maximum workpiece weight: 200,000 kg Machine weight: 550,000 kg Please submit your offer.

Condition: as good as new (ex-display), Year of construction: 2016, operating hours: 7,000 h, machine/vehicle number: 0012, REM SC 33 CNC 2MS | Dual-Head CNC Vertical Turning Center | Ø3,300mm Heavy-duty CNC Vertical Turning Center with two independent milling heads and dual automatic tool magazines — built for continuous precision production of large components. CAPACITIES: • Max. Turning Diameter: 3,300 mm (per head) • Max. Machining Height: 2,000 mm (under cross rail) • Max. Workpiece Weight: 20 tonnes WORK TABLE: • Table Diameter: 3,000 mm • Speed (infinitely variable): 1–110 rpm • Main Motor Drive (AC): 100 kW MILLING HEADS (2×): • Each head with independent ATC tool magazine • Simultaneous or independent dual-head operation • CNC-controlled X, Z, W axes KEY ADVANTAGES: Bljdpfjdpdfzox Aktsp ✔ Dual-head configuration = double productivity ✔ Proven REM design — used in energy, mining, and heavy industry ✔ Rigid, thermally stable construction for long-term precision ✔ Full CNC control with digital drives Manufactured by REM Bacau – Romania | Over 60 years of VTL expertise. Machine available for inspection under power. Worldwide export. Contact us for full technical datasheet, video, and quotation.

Condition: used, Year of construction: 1984, functionality: fully functional, overall weight: 2,300 kg, We offer this used Prvomajska BRT50M turret lathe, manufactured in 1984. It is in good working condition. Bodpjz Hma Eofx Aktjlp If you have any questions or require additional information, please send us a message or contact us by phone.

Condition: good (used), Year of construction: 1972, functionality: fully functional, turning height: 1,000 mm, turning diameter: 1,600 mm, faceplate diameter: 1,400 mm, Retrofit: 2001 Siemens control system SINUMERIK 840D Faceplate diameter 1,400 mm Turning diameter 1,600 mm Turning height 1,000 mm Fully functional. Please refer to the photos for further information. A video of the machine in operation can be provided upon request. Inspection appointments are possible by arrangement. The buyer must arrange the collection. Loading onto a truck/container provided by the buyer is included. Invoice with VAT shown. Since these are used machines/used accessories, we exclude any warranty or guarantee. The information is provided to the best of our knowledge, and we assume no liability. Blsdpjzvl R Refx Aktep We reserve the right to make changes to technical data and to correct any errors in the description. The buyer has the right to inspect the goods for condition and functionality before concluding the contract. We exclude any warranty for obvious and hidden defects, as well as compensation for damages of any kind, including damages that did not occur to the delivered item itself.

Condition: used, Year of construction: 1970, Diameter of the table 3000 mm turning diameter Max. 5500 mm column travel 1000 mm table turning speeds 82 U/min table load max. 25 t turning height 2000 mm weight of the machine ca. 75 t Workpiece height 1850 mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale Blodezhn Txspfx Aktep apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team