Used Vacuum Dry Chamber for sale (7,383)

Condition: used, Year of construction: 2016, // Equipment dismantled and stored in our warehouse // Manufacturer: Italvacuum Model: Cosmodry System IHD 3200 Year: 2016 Type: horizontal vacuum paddle dryer Application: drying wet powders ATEX (Eex) unit: yes Bsdox R D Efepfx Afhslc Industries: Fine chemicals, pharmaceuticals (API), intermediates A) Agitation: Concentric agitator with heated shaft, removable in several segments (double mechanical seal) Transmission: (CEMP) - Power 30 kW + Gearbox + Chain Agitation speed: 1.6 ÷ 8.1 rpm Atex: explosion-proof ATEX II 2GD Mounted with the dryer on a support structure (single SKID) B) Drying chamber with discharge valve Total volume : 3200 Liters Useful volume : 30% - 80% Internal pressure : -1 / 0,5 barg Jacket pressure : 0 / 1,7 barg Project temperature : -10 / +130°C Maximum heating fluid temperature: +100°C Best vacuum tightness: 4 mbar/h EX-I absolute pressure transmitter PT100 Ex-i product temperature sensor Nitrogen backwash system Rotary chopper speed: 300 / 1200 rpm (not installed) Material in contact with the product: AISI 316L - EN 1.4404 Vacuum seals: PTFE and FEP Jacket material: AISI 304 - EN 1.4301 Heating fluid: Diathermic oil Mirror-polished interior finish (Ra ≤ 0.4 µm) Satin exterior finish (Ra ≤ 1.2 µm) Inspection and Shut-off Valve DN.1650 Buffer Relief Valve DN 200/300 DN 250 Butterfly Loading Valve Prepared for the installation of two choppers (lateral knives) C) Process filter D) Vacuum unit: SAURUS939 piston vacuum pump, model VVD Pump support bench ATEX: Ex-d-IIB-T4 – IP55 Power: 11 kW Atmospheric pressure surface condenser, model VD200I E) Vacuum condensing unit - AISI 316L stainless steel with double cooling jacket in AISI 304 stainless steel. Internal design pressure: -1 / 0.5 barg Jacket design pressure: 0 / 3 barg Design temperature: -10 / 40 °C Maximum cooling liquid pressure: 2.5 bar Exchange surface area: 8.5 m2 Condensate collection capacity: 900 litres Level sensor F) External safety filter G) Temperature control system: Heating/Cooling Steam liquid heater: Pressure 7 bar - Jacket temperature: 142°C - Surface area: 1.65 m2 Cooler, mounted on the heater: cold water or brine - Pipe jacket pressure: 12 barg - Jacket temperature: 142°C - Pipe temperature: -10°C /+ 99°C - Surface area: 3.42 m2 H) Command and Control System (Electrical Cabinet + HMI) Complete technical file

Condition: used, Year of construction: 1988, Manufacturer : Comber Model: Pharmadry PH 100 Year : 1988 Type : vacuum dryer   Maximum temperature: 99°C Material: 304 and 316 stainless steel (in contact with product). Classification: Atex EEx IIB T4   Main tank diameter : ø 500 mm Main tank depth: 700 mm Power: 4 HP Bljdpfxsx R Avio Afhjc Filter Pressurised receiver tank Tubular heat exchanger   Gaskets: new Paint: new Mechanical seal: As is, good condition

Condition: used, // Sold as is or reconditioned // Vacuum paddle dryer mixer Used for products such as powders/powdery substances. Bjdpsx Rz Spofx Afhjlc 316 stainless steel Tank diameter 1000 x 2000 Volume: 1100 litres Jacketed 86 litres / 1 bar - 120°C Heated agitator 235 litres / 1 bar - 120°C Agitation by 8 scraping blades Loading via 400 diameter Discharge 350 diameter with guillotine valves ADF 15 kW motor Self-cleaning filter

Year of construction: 2026, condition: reconditioned (used), functionality: limited functionality, machine/vehicle number: 559, Dryer optimized for thick timber or hardwood Usable length: 5000 mm Usable height: 1100 mm Usable width: 1100 mm New electrical cabinet and sensors Controlled drying function Blodpfx Afeya Ik Ashec Missing external rail and trolley (can be supplied or we will assist the buyer with fabrication) Dryer can be inspected in department 74

Condition: excellent (used), Here we offer you a chamber dryer. Outer dimensions approx. width: 1.885 mm depth: 1.200 mm height: 2.425 mm Usable space dimensions approx. width: 1.030 mm depth: 1,000 mm Height: 2,100 mm Usable space: 2.2 m³ Nominal temperature: 100 °C Working temperature: 85 °C Heating medium: 3 x 400 V, 50 Hz Heating capacity: 20 kW Circulating air volume: 4,500 m³/h / 400 Pa Motor power: 1,1 kW Protection class: IP 54 The chamber heating furnace must not be used for flammable or explosive substances. The chamber heating furnace must not be installed in the Ex-area. Paternoster device External dimensions: Height: 1,880 mm Width: 809 mm Depth: 950 mm support sets: 13 pieces Pitch: 228 mm Carrying set width: 354 mm Carrying set depth: 320 mm useful height: 135 mm Bedpfx Afsgm Hwuohslc Power of drive motor: 0.25 kW at 189 Nm Transport speed: on average 5 m/min. Payload/carrier set: max. 10 kg total payload: max. 130 kg total weight loaded: max. 730 kg year of construction: 2005 Type: Ke/SO Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, data are reserved!) Further questions we can answer on the phone for you.

Condition: used, WSA Lignomat vacuum dryer Bljdpfx Aexxpdtjfhec Control unit: Bollmann Tromatic 910GH Depth approx. 10 m

Year of construction: 2001, condition: excellent (used), RICE REDUCTION!!! Instead of 1.150 EUR only 950 EUR!!! Bsdpfx Aopgultefholc Dryer with material conveyor Moretto Type SHD25 power 2940 Watt Moretto material conveyor Type T 2L Vacuum pump Moretto Type VI T2

Condition: as good as new (ex-display), Year of construction: 2021, Binder VDL 115 (2021) – Laboratory Vacuum Chamber, Perfect Condition, Demo Unit Model: Binder VDL 115 Year of manufacture: 2021 Condition: As new – showroom specimen, post-factory testing Capacity: 115 liters Power supply: 230 V Availability: Immediate Warranty: Yes (start-up warranty) VAT Invoice: Yes Location: Grabina 92-701, Poland Optional: Transport available — Description: We offer for sale a Binder VDL 115 vacuum chamber designed for drying organic solvents and flammable substances under vacuum conditions. This is a VDL safety series model meeting ATEX requirements, intended for operation in explosion hazard zones (class 3). The unit was used solely for demonstration purposes – it is in perfect visual and technical condition and comes with complete documentation. — Key features: • Temperature range: from +9°C above ambient to +200°C • Usable capacity: 115 liters • Interior made of stainless steel (1.4571) – chemically resistant and easy to clean • Controlled, safe vacuum with adjustable level • ATEX 2014/34/EU compliant, safety class 3 • Control panel with LCD display, programmable parameter regulation • Standard equipment: 2 aluminum shelves + inert gas valve — Applications: • Pharmaceutical and chemical industry • R&D laboratories • Drying of solvents, non-reactive materials, and temperature-sensitive samples • Production of electronic and precision components — Why it’s worth considering: • The chamber is in immaculate, as-new condition • No signs of wear, full technical documentation included Bljdpovq I Tnjfx Afhec • A perfect alternative to a new unit – no lead time • Attractive price, possibility for on-site testing or remote demonstration

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood Bledpfev Si Szex Afhjc The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Year of construction: 2020, condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. Bedpfxjfzq Sto Afhelc The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Each tank has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog

Year of construction: 2020, condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Each tank has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system Blsdpfx Afeflmdbehsc • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog

Year of construction: 2020, condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Blodpsfy T Szefx Afhjc Each tank has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog

Year of construction: 2025, condition: new, functionality: fully functional, overall weight: 700 kg, total length: 2,860 mm, total width: 1,230 mm, construction height: 1,700 mm, Fully operational exhibition dryer, Ø 1090 mm We are offering our fully operational exhibition dryer with a diameter of 1090 mm. The unit is very compact and practical in terms of required space and easy relocation. Technical Details: Bledpfxoxbz Hro Afhec Connection: only a water connection for spraying and a 16A power plug are required Heating system: 4 kW electric heater Wood moisture measurement at 3 measuring points Plug-and-play design – ready for immediate use Advantages: Ideal for small carpentry workshops Easy to transport and flexible positioning

Condition: ready for operation (used), Technical characteristics tank 1000 mm tank length 4600 mm trays dimension 700 x 4000 mm height 700 mm max closed length 4700 mm electric boiler programming example: wood thickness 45/60 mm initial humidity 35/45% plate temperature 45/60 C ° total time 90 H (manufacturer data cannot be committed) Power and Motors Voltage: 400 V Pluging: Three-phased Overall dimensions Lenght: 4600 mm Width: 1000 mm Blodpfx Ajt Hzvwofhjc Height: 1100 mm Weight: 1500 Kg

Condition: ready for operation (used), Technical characteristics Total volume 1,6m3 Length 4800 mm Width 700 mm Loading height 500 mm Brand new membrane Cycle and temperature adjustable on the control panel according to the species and thickness of the wood Brand new heating resistance and vacuum pump 6 heating plates Ideal for carpentry and fast drying (-90h) of small volumes of lumber Power and Motors Blodpfx Ast Hzvqofhjc Overall dimensions

Condition: ready for operation (used), Technical characteristics Volume: 12 m3 Useful dimensions : Length 7400 mm Width 1500 mm Bodpfx Afst Hzvkohslc Height : 1350 mm External dimensions: 8400 mm x 2700 mm 28 circulation heating plates (Dimensions 6400 mm x 700 mm) Completely revised New vacuum pump 5,5 kW (TRAVIANNI) Power and Motors Overall dimensions

Year of construction: 2002, condition: excellent (used), Parts in contact with the product are made of stainless steel 1.4571, the rest of the dryer is made of 1.4301. Machine Name: Continuous Horizontal Vacuum Paddler Dryer used Manufacturer: AVA / Holland Merten GmbH Type: HTK 200 Construction year: 2002 Speed: 107 rpm Material: 1.4301 Driving force: 5,5 kW Model: EExdellCT4 Total content: 235 Liter Parts in contact with product: 1.4571 Equipment: Double jacket, mechanical seal Dimensions: L 3400 x W 1100 x H 1500 mm Bodpfx Aeitcu Eefhjlc Empty weight: approx. 1600 kg Technical documentation: Yes Message: Operating temperature 130°C Design temperature 200°C Internal pressure mixer -1/+3 bar Pressure double jacket +6 bar Accessories: Base frame Condition: Used

Condition: excellent (used), I sell the pump FEZER 016-118 94213 - Pump in bdb condition. Blodsud Ryrepfx Afhec - Capacity 16m3/H

Condition: new, Setting total time Frequency speed control Automatic unloading Vacuum 0-95% Vacuum system filter Machine dimensions in cm: Length: 300 Width: 180 Height: 200 Electric power: 7.5 kW Blodpfxoul T Ics Afhjc

Condition: new, functionality: fully functional, Year of construction: 2025, There are several types of ball mill grinding plants designed for different applications and industries. The choice of the specific type depends on factors such as the material being processed, the desired final product characteristics, and the production capacity required. Here are some common types of ball mill grinding plants: 1. Open Circuit Ball Mill: - In an open circuit ball mill, the material passes through the mill only once, and the finished product is obtained directly. This type is suitable for dry grinding and often used for cement grinding. 2. Closed Circuit Ball Mill: - Closed circuit ball mills have a separator, which separates the fine particles from the coarse ones. The coarse material is returned to the mill for further grinding, while the fine product is collected and sent to storage. This type is commonly used in mineral processing circuits. 3. Overflow Ball Mill: - Overflow ball mills discharge the slurry over a trunnion at the discharge end. This type is suitable for wet grinding or when the slurry has a high moisture content. Bedpfx Afeq Nx Alsholc 4. Grate Discharge Ball Mill: - Grate discharge ball mills discharge the slurry through the grate at the discharge end. This type is suitable for dry or wet grinding and is often used for grinding materials with high moisture content. 5. Peripheral Discharge Ball Mill: - In a peripheral discharge ball mill, the grinding chamber is larger at the feed end, allowing the material to be discharged peripherally. This type is suitable for coarse grinding and often used for rod mills. 6. Planetary Ball Mill: - Planetary ball mills are designed for high-energy milling and are suitable for both dry and wet grinding. They have one or more grinding jars that rotate around a central axis, creating a planetary motion. This type is often used for laboratory applications. 7. Ball Mill with Ceramic Lining: - Some ball mills are lined with ceramics to reduce wear on the inner surface of the mill. This is particularly common in the production of ceramic materials, pigments, and refractories. 8. High-Energy Ball Mill: - High-energy ball mills use mechanical alloying processes to create new materials. These mills operate at high rotational speeds, causing the balls and the material being ground to impact with high energy. They are suitable for milling hard and brittle materials. 9. Air-Swept Ball Mill: - In an air-swept ball mill, the material is fed into the mill with ambient air, and the finished product is collected in a dust collector. This type is commonly used for coal grinding in the cement industry. 10. Tube Mill: - Tube mills are long cylinders with a charge of steel balls used for grinding raw materials, coal, and clinker. They can be open or closed circuit and are widely used in cement and mineral processing industries. 11. Continuous Ball Mill: - Continuous ball mills operate continuously, and the material to be ground is fed at one end and discharged at the other. These mills are suitable for grinding materials in a continuous process.

Condition: new, Year of construction: 2026, functionality: fully functional, compressed air connection: 20 bar, total width: 500 mm, total length: 550 mm, total height: 1,000 mm, overall weight: 96 kg, input voltage: 230 V, warranty duration: 24 months, 💥 NozziTec X-Force Dry Ice Cleaning Machines – New & Immediately Available! 💥 Dry ice blaster / Cold Jet Quality Are you looking for top-quality industrial cleaning technology for your business? We offer brand-new NozziTec X-Force dry ice cleaning machines, exclusive and ready for immediate use. NozziTec is a leading manufacturer with over a decade of experience in dry ice cleaning technology — machines designed for maximum efficiency, reliability, and safety. 🛠️ Why choose NozziTec X-Force? ✅ Professional quality: Premium Polish engineering with rugged construction and high-grade components; ideal for demanding industrial environments. ✅ Durable & reliable: 24-month warranty and excellent support. ✅ Efficient & clean: Clean surfaces without water or chemicals — fast, sustainable, and environmentally friendly. ✅ Versatile: Perfect for maintenance, production cleaning, renovations, or deep degreasing in workshops, industry, and technical services. 📦 Available models 🔹 X-Force M1 – Efficient, low air consumption, and ideal for light to medium cleaning tasks. €21,000 🔹 X-Force M2 – Powerful all-round machine with extensive options for industrial applications. €23,000 🔹 X-Force M3 – 20 bar Unmatched cleaning power for the toughest conditions. €25,300 📌 Optional: Full range of accessories, nozzles, blast hoses & service kits available. 💼 Perfect for, among others: 👉 Injection molds and dies 👉 Industrial machinery & production lines 👉 Removal of paint, grease, oil, and fire residues 👉 Restoration and renovation of metal, stone, or wood 👉 Cleaning of electrical equipment (moisture-free) 📞 Quotation, demo, or questions? Interested? Request a quote, demonstration, or non-binding offer today! We are happy to assist you with tailored advice. Worldwide shipping. Blodpfx Aoyf Aaijfhjc

Condition: new, Year of construction: 2026, functionality: fully functional, overall weight: 30 kg, total length: 33 mm, total width: 40 mm, total height: 130 mm, operating pressure: 2 bar, final pressure: 2 bar, warranty duration: 24 months, Pneumatic Vacuum Liquid Filling Machine – Constant Fill Level Bledpfx Aerivxyjfhsc This vacuum liquid filling machine operates fully pneumatically and requires no electricity. A small compressor is sufficient to operate the machine. Thanks to the vacuum-controlled constant-level filling principle, each bottle is filled to exactly the same liquid level, regardless of bottle volume variations. This ensures a consistent and professional final result. Compact, Lightweight, and Durable The machine is manufactured entirely from high-grade stainless steel, is compact in design, lightweight, and takes up little space. It is easy to place on a workbench, making it ideal for both production and testing environments. Versatile Applications Suitable for filling both small and larger volumes of liquid products, including: - Water - Perfume - Milk - Eye drops - Oils (such as sesame oil) - Beverages - Alcohol - And similar liquids Efficient Operation The machine is equipped with two filling heads, allowing for continuous operation. Depending on the operator and bottle volume, up to approximately 20 bottles per minute can be filled. Contact & Delivery For questions or further information, please feel free to contact us by email or telephone. Transport within and outside Europe is possible.

Condition: refurbished (used), Cutter Vacuum TIPPER-TIE 330V After renovation with warranty! Height: 2250 mm Width: 3300 mm Length: 2800 mm Capacity: 330 l Bowl construction - stainless steel Knife construction - stainless steel Electric power supply: 400V 50Hz 3N Total power: 141 KW - Knife rotation: 540/960/1930/2880/3850/4050.-smooth adjustment Bjdpfot Sv Ulex Afhelc - Bowl rotation: 3.5 / 6.5 / 10 / 13.5 - Mixing speed: -70/120 - bowl rotates to the left - Power: 141 kW - Weight approx. 7800 kg - Number of knives – 6 pcs.

Condition: good (used), Forklift battery charger, industrial charger, forklift battery charger, industrial charger Bjdpfx Afsb A Hdzjhslc -24 volts -Power: 20 A -Connection: 230 volts -Number: 7 chargers available -Price: per piece -Weight: 18 kg/piece -functionally tested

Condition: excellent (used), Year of construction: 2002, ALU-profile mitre saw Fabr.Dry Tech Bledpetwn E Uofx Afhoc Type:355 MLS Year 2002. Saw blade dm.355 mm Cutting range round max.120 mm Square max 120 mm X 120 mm