Used Weiler Lz 330 for sale (175)

Condition: repair required (used), Year of construction: 1990, LZ-Lathe Fabr.WEILER Type : COMMODOR Year 1990 with 3 axes digital readout Heidenhain, Multifix holder B, steady rest, machine documentation Machine is defective ( clutch ) Hsdpfxsq Hd Ips Am Djnl Center height: 214 mm turning diameter over face support : 200 mm Center distance : 1000 mm spindle bore : 60 mm Spindle speeds : 45 - 2000 rpm Machine is sold at a fixed price.

Year of construction: 2010, condition: like new (used), We have the following accessories for Weiler E30 lathe. 1.piece .faceplate Schunk 250mm price:600,-€ Spindle head DIN 55027 size 5 Hjdpfxsgabvno Am Donl 2.pieces.faceplate Röhm 260mm price each 1.piece:650,-€ spindle head DIN 55027 size 5 1.piece.travelling steady rest Price: 450,-€ 2.pieces.driving flange Price per. 1 piece: 210,-€ Spindle head DIN 55027 size 5 All parts are in very good condition.

Condition: used, Year of construction: 1991, functionality: fully functional, machine/vehicle number: 91-160-2498, Used WEILER PRAKTIKANT 160 lead and feed screw lathe Centre height: 160 mm Centre distance: 650 mm Spindle speeds approx. 48–2,500 rpm Spindle bore: 40.5 mm Leadscrew and feed shaft are covered. Hodpfx Amjyciw Aj Denl Scope of delivery: Including 3-axis digital readout from Heidenhain, chip guard back wall, lever collet system (without collets), 1 x faceplate Ø 250 mm, electrically interlocked chuck guard, machine lamp, Multifix size A quick-change toolpost with 4 holders, bed stop, cooling unit, and fixed steady rest. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Viewing by appointment is possible.

Condition: used, Year of construction: 1995, turning diameter 720 mm turning length 3000 mm control Siemens 805 turning diameter over slide 430 mm turning speeds 1800 U/min tailstock quill taper MT 6 steady 3 Stück main drive motor 36 kW z-axis 3050 mm x-axis 410 mm swing diameter over slide rest 430 mm spindle motor 28 kW workpiece weight 3000 kg spindle passage 106 mm 3-jaw-chuck diameter 305 mm total power requirement . kW weight of the machine ca. 6 t dimensions of the machine ca. 4x2,4x2 m Steady rest 1: Diameter: 120-300 mm Steady rest 2: Diameter: 220-400 mm Steady rest 3: Diameter: 350-500 mm Chuck: Diameter: 315 mm Maximum workpiece weight: 3 t (with steady rest) The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Hodjyqvbdspfx Am Denl We look forward to your visit. Your Markus Hirsch Team

Condition: ready for operation (used), functionality: fully functional, Distance between centers: 500 mm Center height: 160 mm Spindle bore: 36 mm Spindle speed: 56 – 2000 rpm Tailstock: MT 3 Drive power: 2.4 kW Weight: 650 kg Dimensions: 1,400 x 700 x 1,220 mm Digital readout: Optional at extra cost Hnodpfx Amoypbype Dol Accessories: Additional accessories available on request!

Condition: good (used), Year of construction: 1985, functionality: fully functional, turning diameter over cross slide: 160 mm, spindle bore: 36 mm, turning diameter: 300 mm, center height: 150 mm, center width: 500 mm, total length: 1,500 mm, total width: 800 mm, total height: 1,300 mm, spindle speed (max.): 3,550 rpm, spindle speed (min.): 15 rpm, overall weight: 1,000 kg, Conventional lathe, center high 150 mm, between centers 500 mm, bore Ø 36 mm, 18 speed 15 - 3550 rpm, motor 3 kw, equipement: collet device, coolant device, 3-jaws chuck, rotating pin, drill chuck, tool post RAPID with 5 toolholders, lamp, dimensions 150x80x130 cm, weight ca. 1000 kgs Hnjdex Urmlopfx Am Del

Condition: good (used), Year of construction: 1988, 1 used lead and feed screw lathe Make: Weiler Model: 160 B Year of manufacture: 1988 Technical specifications Centre distance: 650 mm Swing over bed: 320 mm Swing over cross slide: 192 mm Centre height: 160 mm Spindle bore: 40 mm Rated power: 2.4 / 3 kW Spindle speeds: 48 – 2500 rpm Dimensions: approx. L 2.20 x W 1.10 x H 1.40 m Weight: approx. 1 t Hsdpfx Aew Sdr Hsm Donl Equipment Heidenhain digital readout Multifix toolholder with various inserts 3-jaw chuck Emergency stop

Condition: used, turning diameter over bed / mm turning diameter over slide rest / mm turning length / mm Hodpfx Ajwgi Tmem Djnl

Condition: new, Year of construction: 2025, CONDOR VC plus The new dimension in conventional precision lathes. Hodsqwipnjpfx Am Djnl A high-quality, powerful and energy-efficient precision lathe for the highly productive area of production and toolmaking, but also for training and further education High-quality, energy-efficient, precise and universally applicable in production, training and further education. It impresses with: future-oriented technology maximum accuracy durability user-friendly ergonomics minimum space requirement and a wide range of accessories. The consistent and innovative further development of the tried-and-tested Condor series is the economical and intelligent solution for your daily applications. Technical data: WORKING AREA Center height 180 mm Swing diameter over bed 360 mm Swing diameter over facing slide 190 mm Center width 800 mm TURNING SPINDLE Spindle head DIN 55027/DIN ISO 702-3 size 6 Spindle bore 57 mm Spindle diameter in front bearing 90 mm MAIN DRIVE Drive power 60 %/100 % ED - / 10.5 kW Speed range 25 - 4,000 min-1 Number of speeds infinitely variable FEED RANGE Number stepless Longitudinal 0.01 - 6 mm/rev Plan 0.003 - 2 mm/rev THREAD CUTTING RANGE Metric thread 0.1 - 20 mm REITSTOCK Quill diameter 50 mm Quill stroke 110 mm Internal taper DIN 228 MK 3 ACCEPTANCE ACCURACY DIN 8605 Equipped with WEILER WTS 15 VC plus screen display - Large, clearly arranged 15" touch screen, rotatable and tiltable, resolution 1366 x 768 - Change of operating screens via swipe movements - Operating functions can be called up via app manager - Control panels can be freely configured, placed and scaled as required - Drawings / sketches can be imported from PDF files Can be zoomed individually via USB interface - Video-supported maintenance of the machine - Context help menu (instead of screen display WEILER VC plus) The machine is located in our showroom in 71334 Waiblingen-Beinstein and is available immediately. Please contact us regarding equipment.

Condition: used, Year of construction: 2000, used CONDOR AC, partially overhauled Centre height: 165 mm Between centres: 750 mm Spindle bore: 40 mm Spindle speeds: 22–2,800 rpm, infinitely variable - Quick-change tool post size B - WEILER DZ-V digital readout - Hollow spindle stop - Fixed steady rest - 7 Multifix tool holders - Flat splash guard - Electrically interlocked chuck guard Hjdox E Um Nopfx Am Donl - Change gears and various soft jaws The machine is partially overhauled: - Bed slide: guideways re-coated and hand-scraped, gibs and lower guide strips adjusted - Cross slide measured and aligned on bed slide; cross slide dovetail guide newly scraped, gibs adjusted and scraped - Top slide newly scraped and gib matched - All measuring scales overhauled and cables replaced The machine is located in our showroom at 71334 Waiblingen-Beinstein and is immediately available. For details on equipment, please contact us.

Condition: new, Year of construction: 2025, GSD Intern One of the best-selling and most popular conventional precision lathes Impressive thanks to: Sophisticated technology Highest accuracy Durability Proven ergonomics Minimal footprint And extensive accessories. Proven for decades in single-part and small-batch production, in trade and industry, training and continuing education, and tool and fixture construction. Distance between centers 650 mm Center height 160 mm Automatic handwheel disengagement Leadscrew and feed screw covers Main spindle brake Toolmaking precision according to DIN 8605 Pole-changing brake motor Headstock gearbox 16 fixed speed levels Numerical position display (option) LED machine light TECHNICAL DATA: WORKING AREA Center height 160 mm Swing over bed 320 mm Swing over cross slide 190 mm Distance between centers 650 mm TURNING SPINDLE Spindle head DIN 55027/DIN ISO 702-3 Gr. 5 Spindle bore 43 mm Spindle diameter in front bearing 70 mm Hedewhzcpspfx Am Denl MAIN DRIVE Drive power 60%/100% duty cycle 2.6 / 3.1 kW Speed range 48 – 2,500 rpm Number of speeds 16 FEED RANGE Number 24 Longitudinal 0.02 – 0.63 mm/rev Cross 0.006 – 0.2 mm/rev THREADING RANGE Metric threads 0.25 – 8* mm TAILSTOCK Quill diameter 40 mm Quill stroke 85 mm Internal taper DIN 228 MK 3 ACCEPTANCE ACCURACY DIN 8605 * Inch threads and metric thread pitches 0.45; 0.75; 4.5 and 5.5 are only available with additional change gears. This machine is located in our showroom in 71334 Waiblingen-Beinstein and is available immediately. Please contact us regarding the available options.

Condition: used, machine/vehicle number: 1717, Used lead and feed screw lathe WEILER PRAKTIKANT Hnsdpfx Aouqb Emjm Dol Centre height: 140 mm Distance between centres: 500 mm Spindle bore: 36 mm Spindle speeds: 42–2,000 rpm Equipped with RSF 3-axis digital readout, 1 pc 3-jaw chuck Ø160 mm, Chuck guard electrically interlocked, With Multifix toolpost size A with 3 holders Lever-operated collet device with 15 collets. The machine is located at our facility in 71334 Waiblingen-Beinstein and is immediately available. Viewing of the machine is possible by prior arrangement.

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 1824 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 Hnjdovrcqdjpfx Am Dsl >> Tailstock MK 4 >> Feed rates from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake >> 2 emergency stops On request: covers for the guide. and feed spindle About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. Even at high speeds, the Weiler runs very quietly. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 2020 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feeds from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametrical pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake >> 2 emergency stops On request: covers for the guide. and feed spindle Hnjdpfx Amevrckqo Del About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. The Weiler runs very quietly even at high speeds. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and feed spindle table lathe in excellent condition! Technical specifications: >> Machine no. 2801 >> Center height 120 mm >> Center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short-taper spindle head DIN 55027 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Hedpjv Tyzcofx Am Donl Accessories and equipment: >> 1 x Röhm 125 mm three-jaw chuck with 4 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increments of 1 mm Drawbar >> Multifix size A with 4 tool holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle cover >> Clamping tool About the machine: Offered is a Weiler Primus table lathe with guide rail and drawbar in very good condition. The machine is fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. The Primus comes from a state-owned company where it was used little. This newer generation of Weiler lathes is very user-friendly, and surfaces can be produced with a polished finish. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition. (The base cabinet is included; the machine is not bolted to the machine.) A digital display is available for an additional charge.

Condition: used, functionality: fully functional, Weiler Matador VS-2 guide and feed spindle lathe Technical data: >> Year of manufacture approx. 1970 Machine no. M1012 >> Center height 140 mm >> Center width 500 mm >> Speed: 30 – 3550 rpm >> Spindle passage 36 mm >> Short taper spindle head DIN 55022-5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.010 to 1.184 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 15 mm >> Weight approx. 700 kg >> Length 1.4 m, height 1.2 m, depth 0.55 m Hodsvv Etvspfx Am Dsnl Accessories and equipment: >> Collet device 32 collets (set is not complete) with holder >> 1 three-jaw chuck 1 set of jaws >> 1 four-jaw chuck 1 set of jaws >> Mulifix size A with 2 steel holders >> Change gears >> Bed stop About the machine: A used Weiler Matador VS-2 is offered in a fully functional condition. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler Praktikum 160B precision center lathe 3-axis digital display K&C NEW. Reconditioned with acceptance certificate for tolerances of new machines Hedpevrdlcsfx Am Djnl Technical data: >> Machine no. 87 160 760 >> Center height 160 mm >> Center width 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle passage 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.02 to 0.63 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake can be switched on >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching the counting direction, >> Collet device New, collets NEW from 3 to 25 mm, 1 mm increasing >> Three-jaw chuck 160 mm New with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Electronic spindle protection >> Machine lamp LED New >> Machine feet NEW >> Splash guard >> Operating instructions, spare parts plan (PDF) About the machine: Offered is a Weiler Praktikum 160 B guide and feed spindle lathe with toolmaker precision in a completely geometrically overhauled condition. Reconditioned with acceptance certificate for tolerances of a new machine. For safety: Electronic spindle protection of the work spindle, cover of the lead and feed spindle, 2 emergency stops and a brake motor. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler center lathe Model Condor 81 guidance and feed spindle lathe with 3-axis digital display from K&C, NEW Geometrically overhauled with inspection protocol for new machine tolerances Technical data: >> Machine No. 84-121 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: metric, imperial, module, and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Equipment and accessories: Hnsdjwrm Dtjpfx Am Djl >> 3-axis digital display from K&C, new, 12 months manufacturer warranty with operating instructions Functions: switching mm/inch, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 pcs., taper calculation, radius/diameter, quick zeroing, count direction switching >> Collet chuck NEW, collets NEW from 3 to 26mm, increments of 1mm >> 160 mm three-jaw chuck with 2 sets of jaws NEW >> Multifix size B NEW with 3 piece steel holders >> Bed stop >> Electric chuck guard NEW >> Rear wall >> Operating manual >> Coolant device >> Machine feet About the machine: A Weiler Condor 81 guide and feed spindle lathe in a very good, geometrically overhauled condition is being offered. The guides are newly ground or newly scraped. Inspected according to test protocol. The accessories collets and chuck are new. For safety: The machine has a brake motor, electronic spindle guard and two emergency stops, making it an absolutely as-new lathe. Even at high speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is very user-friendly and allows surfaces as if ground to be produced. Take the opportunity to view this machine on site under power and convince yourself of its condition.

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, Weiler Praktikant 160 B lead and feed screw lathe with 3-axis digital readout K&C NEW Technical data: >> Year of manufacture: 1986, machine number 86-160-348 >> Center height: 160 mm >> Distance between centers: 650 mm >> Spindle speeds: 8 steps; from 96 to 2500 rpm >> Spindle bore: 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: 0.02 to 0.63 mm/rev >> Usable threads: metric, inch, module, and diametral pitch >> Metric thread pitches: 0.25 to 8 mm >> Weight: approx. 680 kg >> Spindle brake switchable >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital readout from K&C, new, 12 months manufacturer warranty with operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, direction reversal >> Collet clamping device, collets as new from 1 to 29 mm in 1 mm increments Hnjdewthbijpfx Am Dsl >> 160 mm new three-jaw chuck with 2 sets of jaws >> Multifix size A with 3 tool holders >> Electric chuck guard >> Bed stop >> Rear wall >> Machine leveling feet >> Coolant device About the machine: Offered is a Weiler Praktikant 160 B lead and feed screw lathe built to toolroom precision in very good condition. The machine is, of course, fully functional. The Weiler was completely dismantled and newly painted in light grey. All slides move very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and can produce surfaces as if ground. Take the opportunity to inspect the machine under power on site and verify its condition for yourself.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, spindle bore: 83 mm, turning diameter: 570 mm, swing diameter over cross slide: 340 mm, center height: 280 mm, spindle speed (max.): 2,500 rpm, The machine is designed for heavy-duty turning and series production due to its robust construction! TECHNICAL DETAILS Speed range: 1 – 2,500 rpm Torque: 1,300 – 1,600 Nm Swing diameter over bed: 570 mm Swing diameter over cross slide: 340 mm Hnodpfx Aoymx N Njm Djl Center height: 280 mm Distance between centers: 2,000 mm Spindle bore: 83 mm (optional 128 / 165 mm) Number of turret positions: 8 Turret tool holder: VDI 40 shank Tailstock quill diameter: 80 mm Tailstock taper: MK5 MACHINE DETAILS Control system: WEILER SIEMENS 810D Main drive power: 20 / 17 kW (60% / 100% duty cycle) Dimensions & Weight Dimensions (L x W x H): 3,850 mm × 1,850 mm × 1,750 mm Machine weight: 4,200 kg

Condition: like new (used), Year of construction: 1992, Lathe WEILER Precision center lathe in ergonomic design The Weiler Ergodor is the first German ergonomically designed lathe. It creates a more humane workplace and prevents health problems. The key feature is that the employee can operate this lathe while standing or sitting. Technical data Center width 470 mm Turning length 430 mm Center height 145 mm Rotation Ø over cross slide 160 mm Rotation Ø over bed 300 mm Spindle head, short taper flange Bayonet mounting DIN 55022 size 5 or Camlock clamping D 1-ASA-4 Spindle bore 36 mm DIN 55022 size 5 Spindle inner taper Spindle speeds Speeds 30 - 3550 rpm S Speeds 15 - 3550 rpm Brake motor 3 kW Brake motor 1.5/3 kW Face slide travel 150 mm Travel of the top slide 100 mm Feed rates and thread pitches on the gearbox switchable steps 30 Section 2 1.5/3 kW 38 Gear ratio in headstock 3 20 Long feeds 150 mm via change gears 100 mm via toothed belt Face feeds = 1/2 Longitudinal feed values Metric pitches 0.2 - 12 mm Module pitches 0.1 - 4 Dimensions 1450 x 640 x 1500 mm Dimensions 1450 x 640 x 1500 mm Hjdpfx Aovgqu Hom Donl Net weight 1000 kg Acceptance according to toolmaker's accuracy DIN 8605 20 Built according to the rules of occupational safety, official test no. A. EM 11 1545/80. Encombrement 1450 x 640 x 1500 mm

Condition: good (used), 1 used lead and feed screw lathe Make: Weiler Model: Condor VS 2 Technical Data: Centre height: 160 mm Centre distance: 800 mm Spindle bore: 40 mm Bed width: 240 mm Speeds: 12 - 2800 rpm Drive power: 3 kW Tailstock taper: MK 3 Quill stroke: 110 mm Feeds: 0.037 - 1.253 mm/rev Weight, approx.: 800 kg Dimensions (W x D x H), approx.: 1930 x 880 x 1470 mm Equipment: Hedpfxew Rcrcs Am Donl 3-jaw chuck Quick-change toolholder system Multifix

Condition: used, Year of construction: 2008, turning diameter 720 mm turning length 3000 mm Hodjw A Sqmepfx Am Denl centre height 360 mm spindle bore 106 mm turning speed range 1 - 1800 U/min tailstock quill taper MT 6 workpiece weight max. 3800 kg total power requirement 36 kW weight of the machine ca. 6100 kg dimensions of the machine ca. 4800 x 2450 x 2000 mm CNC lathe - cycle-controlled Equipment: - Chip conveyor - Coolant device - 3-jaw chuck Ø630 mm - MUTLI-FIX quick-change holder - Live center - Machine light

Condition: ready for operation (used), turning length 500 mm Hnedpfx Aexq Hhysm Dsl turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - 1x empty tool cabinet - Emergency stop button - Operating instructions

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min Hedpjxnda Usfx Am Dsnl motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - HEIDENHAIN 3-axis digital display “VRZ 773” - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - 1x empty tool cabinet - Emergency stop button - Operating instructions