Condition: as good as new (ex-display), Year of construction: 2026, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 84 mm, clearance between the columns: 910 mm, displacement volume: 2,050 cm³, injection pressure: 1,620 bar, injection weight: 1,886 g, mold height (min.): 350 mm, ejector force: 110 N, ejector stroke: 250 mm, plate width: 1,260 mm, plate height: 1,270 mm, total length: 7,200 mm, total width: 2,150 mm, total height: 2,230 mm, overall weight: 17,210 kg, type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 183 A, warranty duration: 12 months, Equipment: documentation/manual, Base machine: UN500D1-3330 D=84 Clamping force 500T Tie bar spacing 910x830 Tool installation height 350 to 900 Robot interfaces Euromap 67, Euromap 13 Suitable robot available upon request Basic standard equipment: • CE standard • KEBA-3018 control system • Thermal insulation cover for the cylinder • Energy meter, intelligent version • 2 sets of core pull • 1 set of air blow device on the moving platen Bwedpsz I T E Dsfx Adlew • 1 set of air blow device on the stationary platen • EUROMAP-67 interface • IT system • EUROMAP-13 core pull interface on the stationary platen • EUROMAP-13 core pull interface on the moving platen • 1 set of 6-way water distributor for the moving platen (11 l/min) • 1 set of 6-way water distributor for the stationary platen (11 l/min)

Condition: good (used), Year of construction: 2014, Clamping force: 50 t Screw diameter: 30 mm Distance between tie bars V: 320 mm Distance between tie bars H: 320 mm Shot volume: 85 cm3 Shot weight: 77 g Injection pressure: 2000 bar Bwedpozcaipjfx Adlow Type: Horizontal Drive: Hydraulic

Condition: excellent (used), Year of construction: 2005, Battenfeld HM 270/1330 Injection Molding Machine Bsdpfezc Efcex Adloww Basic Information Manufacturer: Battenfeld Model: HM 270/1330 Year of Manufacture: 2005 Category: Hydraulic Injection Molding Machine Clamping Unit Clamping Force: 2,700 kN (270 tons) Mold Platen Dimensions (horizontal × vertical): 1030 × 1020 mm Distance Between Columns (horizontal × vertical): 710 × 630 mm Minimum Mold Height: 350 mm Maximum Mold Opening: 1150 mm Injection Unit Screw Diameter: 55 mm Injection Volume: 650 cm³ Injection Shot Weight: 565 g Maximum Injection Pressure: 2040 bar Dimensions and Weight Net weight of the machine, including the control cabinet: approximately 12 tons

Condition: excellent (used), Year of construction: 2010, Krauss Maffei KM 300-2000 CX injection molding machine Year of manufacture: 2010 We offer a high-class hydraulic injection molding machine from the renowned manufacturer Krauss Maffei. The machine is equipped with a modern MC5 control system with a color monitor, an integrated operator panel, and three USB ports. Thanks to its robust construction and high performance, it is perfectly suited for the production of thermoplastic parts. Equipment Fully hydraulic clamping system MC5 control system with color monitor Integrated control panel 3 USB ports Complete plasticizing unit for thermoplastics Ø 70 mm screw made of wear-resistant material Backflow valve Open nozzle Technical data Clamping unit Parameter Value Clamping force 3000 kN Mold opening force 169.3 kN Plate movement force – opening 86.3 kN Plate movement force – closing 67.8 kN Dimensions of mounting plates (h × v) 995 × 1050 mm Clearance between columns (h × v) 630 × 630 mm Mold opening stroke 820 mm Minimum mold height 330 mm Maximum opening stroke of plates 1150 mm Ejector stroke 200 mm Ejector force 57.7 / 28.3 kN Injection unit Parameter Value Screw diameter 70 mm Maximum injection pressure 1877 bar Injection volume 1078 cm³ Injection weight (PS) 981 g Injection rate (standard) 385 cm³/s Injection rate (with accumulator) 1155 cm³/s Screw speed 220 / 310 rpm Electro-hydraulic system Parameter Value Pump motor power 55 kW Pump motor power with accumulator 55 kW Heater power 29.2 kW Number of heating zones 6 Number of dry cycles (Euromap 6) 1350 / h Oil tank capacity 720 l Bedsza Uuzopfx Adljww Dimensions and weight Parameter Value Net weight 14.5 t Dimensions (l × w × h) 6.5 × 2.2 × 2.3 m

Condition: ready for operation (used), Year of construction: 2015, operating hours: 68,387 h, clamping force: 13,000 kN, screw diameter: 105 mm, injection weight: 4,779 g, total width: 3,650 mm, total height: 2,820 mm, overall weight: 70,000 kg, controller manufacturer: KRAUSS MAFFEI, controller model: MC6 version 1.4, product length (max.): 13,650 mm, Hydraulic injection moulding machine manufactured in 2015. This KraussMaffei 1300-12000 MX features a clamping force of 13,000 kN and platen dimensions of 2210 x 1910 mm. The injection unit has a screw diameter of 105 mm and a shot volume of 5195 cm³. If you are looking to get high-quality injection moulding capabilities, consider the KraussMaffei 1300-12000 MX machine we have for sale. Contact us for further details. Clamping unit • Platen dimensions: 2210 x 1910 mm • Distance between tie bars: 1570 x 1270 mm • Min. mould height: 700 mm • Max. mould height: 1400 mm • Max. opening width: 3050 mmInjection unit • Injection unit: SP 12000 • Shot volume: 5195 cm³ • Max. injection pressure: 2296 barElectrical and hydraulic • Pump motor power: 132 kW • Heating power: 75 kW • Power supply: 400 V, 3-phase, 50 HzOperating data • Power-on hours: 70003 h 29 min • Production operating hours: 68387 h 27 min • Total cycles: 5,472,772 Additional equipment Bodjz Az Iiopfx Adleww • KraussMaffei LRX 350 linear robot • Material hopper / feeding equipment • Safety guarding around mould and robot area

Condition: excellent (used), Year of construction: 2008, operating hours: 49,673 h, functionality: fully functional, clamping force: 800 kN, screw diameter: 35 mm, displacement volume: 156 cm³, plate length: 740 mm, plate height: 640 mm, total length: 5,350 mm, total width: 1,700 mm, total height: 2,000 mm, overall weight: 6,500 kg, Equipment: documentation/manual, KRAUSS MAFFEI KM 80-380 EX Stock No.: 503232 Manufacturer: KRAUSS MAFFEI Type: KM 80-380 EX Control: MC5 Year of manufacture: 2008 Operating hours: 49673 h Technical data, clamping unit side Clamping force: 800 kN Tie bar spacing, horizontal x vertical: 520 x 420 mm Platen size, horizontal x vertical: 640 x 740 mm Minimum mold thickness: 300 mm Maximum mold thickness: 790 mm Ejector stroke: 100 mm Ejector force: 22 kN Centering of moving platen, diameter: 125 mm Centering of fixed platen, diameter: 125 mm Technical data, injection side Screw diameter: 35 mm Injection volume: 156 cc Injection pressure: 2429 bar Screw length: 23 l/d Screw speed: 477 rpm Free injection flow rate: 289 g/s Number of heating zones: 5 Dimensions & Weight Machine dimensions, length x width x height: 5.35 m x 1.7 m x 2 m Total weight: 6500 kg Equipment Screen text in German CEE socket 16A Air valve 1x Machine with material hopper Machine with water manifold Leveling elements Bwodpfxez Az Rdj Adljw EUROMAP 67 Handling interface USB interface Schuko socket 10A Tool heating 24x

Condition: excellent (used), Year of construction: 2013, operating hours: 30,533 h, functionality: fully functional, clamping force: 900 kN, screw diameter: 30 mm, displacement volume: 106 cm³, plate length: 630 mm, plate height: 580 mm, total length: 4,000 mm, total width: 1,500 mm, total height: 2,200 mm, overall weight: 4,100 kg, Equipment: documentation/manual, BATTENFELD HM 90-210 Stock No.: 503672 Manufacturer: Wittmann Battenfeld Type: HM 90-210 Control System: UNILOG B6 Year of Manufacture: 2013 Operating Hours: 30533 h Technical Data - Clamping Unit Clamping Force: 900 kN Tie Bar Distance h x v: 420 x 370 mm Platen Size h x v: 580 x 630 mm Minimum Mold Height: 450 mm Maximum Mold Height: 925 mm Opening Stroke: 475 mm Ejector Stroke: 150 mm Ejector Force: 41 kN Centering of Moving Platen D: 125 mm Centering of Fixed Platen D: 125 mm Mold Weight: 800 kg Bodpfxez A A Hys Adljww Technical Data - Injection Unit Screw Diameter: 30 mm Injection Volume: 106 ccm Injection Pressure: 2042 bar Screw Length: 22 l/d Screw Stroke: 150 mm Screw Speed: 372 rpm Screw Torque: 490 N Free Injection Rate: 103 g/s PS Number of Heating Zones: 4 Nozzle Distance: 250 mm Dimensions & Weight Machine Dimensions L x W x H: 4m x 1.5m x 2.2m Total Weight: 4100KG Equipment Screen text in German CEE socket 16A CEE socket 32A Hydraulic core pull, 2x Air valve, 1x Leveling elements Plasticizing unit, highly wear-resistant and corrosion-resistant Screw drive with three-phase servomotor Ethernet interface EUROMAP 13 interface EUROMAP 67 Handling interface Interface for color dosing unit Interface for temperature control unit Schuko socket 10A Mold heating, 8x

Condition: excellent (used), Year of construction: 2010, clamping force: 900 kN, screw diameter: 30 mm, displacement volume: 106 cm³, plate length: 630 mm, plate height: 580 mm, total length: 4,350 mm, total width: 1,500 mm, total height: 2,300 mm, overall weight: 4,300 kg, Equipment: documentation/manual, BATTENFELD HM 90-210 Stock No.: 503670 Manufacturer: Wittmann Battenfeld Type: HM 90-210 Control: UNILOG B6 Year of manufacture: 2010 Technical data, clamping unit Clamping force: 900 kN Tie bar distance h x v: 420 x 370 mm Platen size h x v: 580 mm x 630 mm Minimum mounting height: 450 mm Maximum mounting height: 925 mm Maximum platen spacing: 925 mm Opening stroke: 475 mm Ejector stroke: 150 mm Ejector force: 41 kN Centering of moving platen D: 125 mm Centering of fixed platen D: 125 mm Tool weight: 800 kg Technical data, injection unit Screw diameter: 30 mm Injection volume: 106 ccm Injection pressure: 2042 bar Screw length: 22 l/d Screw stroke: 150 mm Screw speed: 372 min Screw torque: 490 N Plasticizing rate: 14 g/s PS Free injection flow rate: 103 g/s PS Number of heating zones: 4 Nozzle stroke: 250 mm Dimensions & weight Machine dimensions L x W x H: 4.35 m x 1.5 m x 2.3 m Total weight: 4300 kg Equipment Screen text in German CEE socket 16A Hydraulic core pull 2x Air valve 1x Machine with water manifold Bwsdsz A A Rljpfx Adlew Machine without material hopper Leveling elements Plasticizing unit, highly wear-resistant and corrosion-resistant Screw drive with three-phase servo motor Ethernet interface EUROMAP 13 interface EUROMAP 67 handling interface Interface for coloring device Interface for temperature control unit USB interface Schuko socket 10A Tool heating 6x

Condition: used, Year of construction: 2005, operating hours: 95,000 h, clamping force: 200 kN, displacement volume: 113 cm³, injection pressure: 2,178 bar, overall weight: 11,500 kg, screw conveyor diameter: 30 mm, terms of delivery: EXW (ex Works) delivery time: on request terms of payment: 100% prior to delivery Bedpfxsz A Iale Adleww

Condition: used, DEMAG Ergotech System 650/1000-3300 with 6,500 kN clamping force and 3300 Euromap injection unit, equipped with a 2021 Wittmann W843 pro robot featuring servo B axis 270° and servo C axis 180°. The machine delivers 1,600 g shot weight through an 80 mm screw, supported by 4 hydraulic core pulls, 8 cascade circuits, and 16 hot runner zones for complex multi-component and technical moulding. CNC CONTROL Controller: Demag Ergocontrol CLAMPING UNIT Clamping force kN: 6.500 Tie-bar clearance (H x V) mm: 1.000 INJECTION UNIT Injection unit size (Euromap): 3300 Screw diameter mm: 80 Max. shot weight (PS) g: 1.600 MOULD FUNCTIONS & HANDLING Hydraulic core pull circuits: 4 Cascade / valve gate circuits: 8 Hot runner control zones: 16 Handling robot (model / year): Wittmann W843 pro (2021) Robot strokes X / Y / Z mm: 1.200 / 2.000 / 3.000 Bwjdpfx Adezz S Uaolew Robot rotary axes (B / C): C servo 180° / B servo 270° DRIVE Max. hydraulic pressure bar: 190 Mains connection V / Hz / A: 3 x 400 / 50 / 241 + 108

Condition: good (used), Year of construction: 1998, Krauss Maffei KM 800-8000 MC injection molding machine Year of manufacture: 1998 Serial number: 8D980U9 Bwjdpfx Aozrwy Aedlew Control system: Krauss Maffei MC3F Clamping force: 8000 kN (800 t) Screw diameter: 130 mm L/D ratio: 22:1 Injection volume: 6570 cm³ Injection weight (PS): 5617 g Injection pressure: 1296 bar Maximum cylinder temperature: 375°C Distance between columns (H x V): 1120 x 1000 mm Dimensions of mounting plates: 1600 x 1530 mm Opening stroke: 2000 mm Minimum mold height: 600 mm Maximum daylight opening: 2000 mm Ejector stroke: 250 mm Ejector force: 226 / 95 kN (front / rear) Screw speed: 92 rpm Injection rate: 929 cm³/s Pump motor power: 132 kW Heater power: 70 kW Number of heating zones: 7 Dry cycle (EUROMAP): 700 cycles/h Oil tank capacity: 3600 l Supply voltage: 400 V / 50 Hz Machine length: approx. 10,500 mm Machine width: approx. 2650 mm Machine height: approx. 2400 mm

Condition: excellent (used), Year of construction: 2021, operating hours: 6,300 h, functionality: fully functional, machine/vehicle number: ADFL9004, clamping force: 80,000 kN, screw diameter: 98 mm, clearance between the columns: 1,020 mm, column diameter: 160 mm, displacement volume: 3,142 cm³, injection pressure: 1,794 bar, injection weight: 2,890 g, mold height (min.): 400 mm, ejector force: 1,82,000 N, ejector stroke: 280 mm, opening stroke: 1,000 mm, plate length: 2,020 mm, plate width: 1,440 mm, plate height: 1,440 mm, total length: 11,200 mm, total width: 2,400 mm, total height: 3,300 mm, overall weight: 35,000 kg, heating capacity: 39 kW (53.03 HP), pressure: 178 bar, number of injections: 1, pump power: 1,16,000 W, power: 163 kW (221.62 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 312 A, Equipment: documentation/manual, The machine has few operating hours and is in very good condition. It has been well maintained. The machine processes only ABS, PP, and PS. The machine is controlled by a Beckhoff system. The machine is equipped with a variety of additional features, including 3 air valves, two hydraulic valves, a servo valve for hydraulic table movement, 8 tool heating zones, a water manifold with 8 zones, a screw heater insulation, hydraulic screw rotation for torpedo replacement, a torpedo with a locking system, an interchangeable centering ring, a Euro-map for the robot, a door with automatic opening via an electric motor, and an electrical cabinet with sockets. Water blocks are also included for both the moving and stationary tables, each with 8 connections. In addition, a number of spare parts are included, such as a complete torpedo, a screw, heaters, temperature sensors, and specific seals for the hydraulics, as well as a self-filtration filter, a torpedo wrench, and auxiliary ejector rods. The machine is sold without the robot shown in the pictures. Bjdpeznlhmjfx Adloww

Condition: used, Year of construction: 2001, operating hours: 70,000 h, clamping force: 50 kN, displacement volume: 739 cm³, injection pressure: 2,470 bar, overall weight: 2,500 kg, screw conveyor diameter: 28 mm, terms of delivery: FCA Pegnitz delivery time: on request Bwedpfjzt Alyex Adlsw terms of payment: 100% prior to delivery

Condition: excellent (used), Year of construction: 2006, clamping force: 500 kN, screw diameter: 22 mm, clearance between the columns: 355 mm, overall weight: 2,700 kg, Clamping force: 50 t Year of manufacture: 2006 Injection unit .../200 Screw diameter: 22 mm Specific injection pressure: 2800 bar Injection volume: 41.8 ccm Mould clamping system 50/... Clamping force: 50 t Mould plate dimensions: 520 x 520 mm Bwsdpjzt Ih Tefx Adlsw Tie bar clearance: 355 x 355 mm Mould height: 210 mm Opening stroke: 400 mm Maximum platen distance: 610 mm Weight: 2700 kg Dimensions (m) L x W x H: 3.8 x 1.1 x 2.1 m Control: NC4

Condition: excellent (used), Year of construction: 2007, clamping force: 1,000 kN, screw diameter: 40 mm, clearance between the columns: 420 mm, injection pressure: 1,865 bar, injection weight: 192 g, mold height (min.): 200 mm, ejector stroke: 100 mm, Year of manufacture: 2007 Injection shot weight: 192g Bodpfx Ajzt I Rnjdloww Injection unit 410 Screw diameter: 40 mm Specific injection pressure: 1865 bar Injection volume: 217 ccm Injection shot weight: 192 g Screw L/D ratio: 20 Mold closing unit 100 Mold plate dimensions: 600x600 mm Distance between columns: 420x420 mm Ejector force: 35 kN Mold height: 200 mm Ejector stroke: 100 mm Weight: 5000 kg Control system: NC4 Tooling: - 2 x hydraulic core - pneumatic valve - Euromap 67 connector

Condition: like new (used), ENGEL barrier screw with mixing elements, used only once or twice for sampling with polypropylene (PP). Bedpfx Aez H Sfgjdloww All accessories shown in the pictures are included in the purchase price.

Condition: ready for operation (used), Year of construction: 2010, operating hours: 55,000 h, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 90 mm, Clamping force 5000 kN Mould opening force, max. 279 kN Travel force movable platen opening 137,1 kN Travel force movable platen closing 116,8 kN Size of mould platens (h x v) 1370 x 1200 mm Distance between tie bars (h x v) 1000 x 800 mm Mould opening stroke 1170 mm Mould height min 480 mm Bwedpfx Aez I Dvysdljw Max. daylight 1650 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 90 mm Ls/D ratio 20 Injection pressure 1839 bar Stroke volume 2290 ccm Shot weight (PS) 2084 gr. Injection rate 604 ccm/s Screw speed 195 1/min Plasticising rate max. 134,2 g/s Nozzle pressure 129,4 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Reservoir capacity 1175 ltr. Dimensions and weights: Dimensions of the machine ca. 8,00 x 2,52 x 2,40 m Total machine weight 28800 kg Max. mould weight 7900 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pull on fix plate - 2 x core pulls on movable plate - 8 x hotrunner controller - Robot interface according to Euromap 67

Condition: used, Year of construction: 2013, operating hours: 55,929 h, clamping force: 160 kN, displacement volume: 23 cm³, injection pressure: 2,500 bar, overall weight: 6,000 kg, screw conveyor diameter: 18 mm, terms of delivery: FCA Pegnitz delivery time: on request Bedpszp R I Ijfx Adljww terms of payment: 100% prior to delivery

Condition: excellent (used), Year of construction: 2021, operating hours: 14,600 h, functionality: fully functional, machine/vehicle number: 248760, clamping force: 40,000 kN, screw diameter: 70 mm, displacement volume: 1,212 cm³, injection pressure: 1,650 bar, injection weight: 1,030 g, mold height (min.): 450 mm, ejector force: 9,64,000 N, ejector stroke: 250 mm, opening stroke: 1,000 mm, plate length: 1,450 mm, plate width: 1,200 mm, plate height: 1,100 mm, installation height: 3,650 mm, total length: 7,740 mm, total width: 2,340 mm, total height: 2,300 mm, overall weight: 25,600 kg, heating capacity: 29 kW (39.43 HP), pressure: 200 bar, number of injections: 1, pump power: 56,000 W, power: 118 kW (160.44 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 213 A, Equipment: documentation/manual, The machine has few operating hours and is in very good condition, having been well-maintained. The machine comes with a Viper12 robot, which was originally supplied with it and can be seen in the accompanying photos. The robot’s control system is not integrated with the machine, so the robot can be removed and used separately, or another robot can be installed in its place. The machine has three air valves and two hydraulic valves, Euro map signals, and a signal for the dispensing unit’s rotation speed. The machine also has a strip guard, which is not included but can be arranged separately. The extruder’s heating elements are insulated with thermal insulation. Due to the guard, the machine can operate with the rear door open. It also has a water tank with 8 zones and two additional blocks with 8 outlets each. The machine has 8 zones for heating the tooling. Only PS material has been injection molded on this machine. Bodpfx Adjzqbk Nolsww

Condition: ready for operation (used), Year of construction: 1999, operating hours: 82,539 h, clamping force: 8,000 kN, screw diameter: 105 mm, Hydraulic injection moulding machine manufactured in 1999. This Krauss Maffei KM800-5700 MC features a clamping force of 8000 kN and an injection unit size of 5700. It has a maximum mould height of 1,100 mm and an opening stroke of 1,400 mm. If you are looking to get high-quality moulding capabilities, consider the Krauss Maffei KM800-5700 MC machine we have for sale. Contact us for further details. • Clamping Force: 8000 kN • Injection Unit Size: 5700 • Screw Diameter: 105 mm • Number of Hydraulic Core Pulls: 4 • Air Valve: 1 (AS) • Operating Hours: Approx. 82,540 h • Mould Height (Min.): 600 mm • Mould Height (Max.): 1,100 mm • Opening Stroke: 1,400 mm • Platen Dimensions: 1,300 × 1,300 mm • Tie Bar Distance (Horizontal): 1,120 mm • Tie Bar Distance (Vertical): 1,000 mm • Centering Ring Diameter: 250 mm Bsdpfxjznuxhs Adlsww • Water Circuits: 8 per Platen • Service History: Inspected and Pump Connections Sealed by Krauss Maffei in 2025 • Machine Condition: Operational • Conveyor Belt: optional • Handling System: optional

Condition: ready for operation (used), Year of construction: 2021, operating hours: 9,500 h, clamping force: 1,000 kN, overall weight: 5,290 kg, This 5-axis SUMITOMO SHI DEMAG IntElect2 100/470-250 was manufactured in 2021. It features a clamping force of 1000 kN and a tie bar distance of 470 mm. The machine includes an injection unit size of 250 and a screw diameter of 30 mm. If you are looking to get high-quality injection moulding capabilities, consider the SUMITOMO SHI DEMAG IntElect2 100/470-250 electrical injection moulding machine we have for sale. Contact us for further details. Bwedszp Ew Dopfx Adlow - Tie Bar Distance: 470 mm- Mould Height Min.: 180 mm- Mould Height Max.: 550 mm- Centering Diameter (Fixed Platen): 125 mm- Centering Diameter (Moving Platen): 125 mm- Ejector Stroke: 150 mm- Ejector Force: 32 kN- Ejector Speed: 333 mm/s- Injection Unit Size: 250- Screw Diameter: 30 mm- L/D Ratio: 20- Injection Speed: 350 mm/s- Control Unit: SDIAS- Mains Connection / Voltage: 400 V / 50 Hz- Current / Amperage: 70 A- Short Circuit Capacity (Icw): 2.0 kA- Max. Hydraulic Pressure (Pmax): 210 bar- Total Weight: 5290 kg- Robot System Model: SDR 5S H&P- Robot Load Capacity: 3 kg- Robot X-Stroke (Transverse Stroke): 1000 mm (Non-operator side)- Robot Y-Stroke (Demoulding Stroke): 400 mm- Robot Z-Stroke (Vertical Stroke): 1000 mm- Additional / Peripheral Equipment:- Material Hopper Loader / Conveyor: KOCH TECHNIK- Temperature Control Unit: HB-THERM Thermo-5

Condition: repair required (used), Year of construction: 2001, functionality: limited functionality, clamping force: 500 kN, clearance between the columns: 305 mm, mold height (min.): 250 mm, plate length: 500 mm, plate height: 500 mm, total length: 3,450 mm, total width: 1,050 mm, total height: 2,000 mm, overall weight: 2,050 kg, Equipment: documentation/manual, Clamping force: 500 kN (50 tons) Column spacing (H x V): 305 x 305 mm Dimensions of the mounting plates: 500 x 500 mm Maximum mold opening stroke: 350 mm Minimum mold height: 250 mm Maximum distance between the plates: 600 mm Maximum screw stroke: 120 mm Bwsdpfozx Agnex Adlsw Injection pressure: up to approx. 1900 bar (depending on the screw diameter) Stroke of the hydraulic ejector: 80 mm Machine weight: approx. 2050 kg Overall dimensions: approx. 3450 x 1050 x 2000 mm Defective control system!!!

Condition: good (used), 1x Arburg 320C 500-170 with Multilift, safety fence, and discharge conveyor. Sold without Z-belt conveyor, temperature control units, and Koch vacuum loader. The machine is available at short notice by arrangement. Bwsdpfx Adszx D Efjlow

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, clamping force: 500 kN, mold height (min.): 225 mm, ejector force: 300 N, overall weight: 2,450 kg, input voltage: 380 V, Equipment: documentation/manual, ARBURG 320 S in excellent condition, low operating hours, and with a Piovan dryer. Year of manufacture: 1998. Piovan dryer, model TDM604. Year of manufacture: 2005. Includes documentation. The machine is powered on for inspection. Bedozxg Amspfx Adlsww

Condition: reconditioned (used), Year of construction: 2002, functionality: fully functional, clamping force: 500 kN, total length: 3,395 mm, total width: 1,000 mm, total height: 2,000 mm, overall weight: 2,510 kg, Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 50M injection moulding machine, fitted with the Procan Controller. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on request. We can take out the hassle and additional costs of purchasing machinery within the UK and EU. Contact us with a potential delivery address and we’ll do the rest. Bjdpfx Aozx Ukfsdloww *The video shown in this listing is of a previously refurbished BOY 50M which is very similar to the BOY 50M machine we are currently refurbishing. Please contact the team if you would like to see the machine in person.