Maka T 2000 milling machine

Maka T 2000

Condition: good (used), Year of construction: 1994, functionality: fully functional, Forward and reverse operation, 3-1000 rpm, Brake motor with Haffner 3-roller feed unit, 8 speeds in good condition 5.5 kW Blodsybv A Ajpfx Aprjh Transport available at extra cost!

Condition: good (used), Year of construction: 1984, SAC used jointer planer SAC FS 430 - 430 mm planing width - 2.90 m table length - 120 mm cutterhead with 4-knife strip knives - 3 kW, 380 volt motor - Automatic motor brake - 8 mm depth of cut - Fence tiltable up to 45° - Swing-away Aigner auxiliary fence - Bridge-type knife guard (cutter cover) - Low-noise design with serrated steel table lips - Extraction port - Weight: approx. 650 kg Location: at customer site Bjdpox Nrvvofx Aprolh - immediately available - Subject to prior sale

Condition: excellent (used), IM Very good condition. Bodpsyxnxlofx Aprolh

Year of construction: 1989, condition: like new (used), Spindle diameter 30 mm 5.5 kW engine power Bedpfx Apohi Tv Hjrslh 5 speeds 3000/4500/6000/8000/10000 U / T 1989 Can be purchased without advance

Condition: used, Year of construction: 1995, Swivel spindle: Yes -5 to 45° Height adjustment: Handwheel Swivel adjustment: Handwheel Milling jaw adjustment: manual Height display: mech. counter Bjdpfx Apjuzkwzsrelh Swivel angle display: mech. counter Milling stop display: mech. counter Milling spindle diameter: 30mm / new milling spindle Speeds: 3000, 4500, 6000, 9000 Motor power: 5.5 kW Motor brake: Yes, automatic Suction connection: 2 x 120mm Machine length: 2000mm Machine depth: 1400mm weight: 900kg

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. Bedpfxjvf E Ave Aprslh All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2025, functionality: fully functional, input voltage: 230 V, planing width: 330 mm, rotational speed (max.): 9,000 rpm, total width: 615 mm, total height: 555 mm, total length: 850 mm, chip removal: 3 mm, height adjustment type: mechanical, number of feed rollers: 1, number of planer blades: 36, planing height: 156 mm, PS33 with spiral shaft • Innovative design and powerful motor. • Chip removal of up to 3.2m. • IN & OUT TABLE. • Double knife cylinder with double-sided knives. • Indicator shows the material removal on the front of the machine. • Planer shaft with reversible knife • No extraction system required thanks to integrated fan to remove sawdust from the planer cylinder • Depth stop with seven positions for repeated thickness planing at the same height • Maximum part width up to 330 mm • Type: PS33 • Recommended use: Craftsmen • Input power (230 V): 1.8 kW Bsdpfjvncu Iex Aprslh • Planer shaft speed: 9,000 rpm. • Planer shaft diameter: 46 mm • Number of reversible plates in planer shaft: 36 pieces • Reversible plate size: 15 x 15 x 2.5 mm, R=150 • Feed speed: 7.9 m/min. • Max. material removal: 3.2 mm • Max. planing width: 330 mm • Max. planing thickness: 156 mm • Min. workpiece length: 120 mm • Extraction: integrated fan, 62 mm suction nozzle or fabric bag • Noise level: 96 dB • Machine dimensions (length x width x height): 340 x 615 x 555 mm • Machine dimensions with tables unfolded (length x width x height): 850 x 615 x 555 mm • Machine weight: 35 kg • Packaging dimensions (length x width x height): 415 x 660 x 545 mm • Package weight: 39 kg Included in the package: • 36 carbide inserts (in the planer shaft) • 5 replacement carbide inserts and screws • Waste bag for sawdust and Dust • Connection set for waste bags • Torx key for changing the inserts (TX25)

Condition: excellent (used), Year of construction: 1982, Table saw ULMIA 1710s Year of construction 1982 Tilting angle 45° Cutting length on cart 750mm Blade diameter max 250mm. Cutting height 75mm. Cutting width between the saw and the attachment 650 mm Scale carriage for cutting angles Table size 1000x630mm Bsdpfx Apjufgnzorelh

Condition: reconditioned (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 690924, Connected load 380V 1,84kW speed 2840 rpm number of spindles: 21 pieces, pitch 32 mm spindle distance 640 mm spindle rotation direction 11xright 10xleft M10 thread 2x safety clamps pneumatic foot valve table size 880 x 400 mm 1x side stop with 2 folding stops 1x basic fence 1x miter fence Unfortunately, we cannot answer inquiries without complete contact information. Blsdpfxoh U Dams Aprjh

Condition: used, Year of construction: 2017, Table dimensions: 2700 x 900 mm HSK 63 F interface 2x spindles for HSK 63 F interface (30 + 40 mm) Spindle tilt: -45° to +45° Usable spindle length: 180 mm Right and left-hand rotation 4-roller feed with motorized height/width adjustment and pneumatic clamping 7.5 kW brake motor with electronic inverter CNC adjustment for: - spindle tilt - spindle height adjustment - complete fence - front part of the fence - table positioning in front of the spindle - electronically variable speed control 1,000 - 10,000 rpm - Aigner milling fence with aluminum jaws - Touchscreen with graphic function - Windows operating system - Camera for importing tool and profile images - Complete fence can be fully swiveled away - automatic star-delta start - central lubrication Weight approx. 1360 kg Blodpfeyudidox Apreh Location: Nattheim