Used 4 Axis Cnc Milling Machine for sale (1,01,356)

Condition: excellent (used), XYZ SMX 3500 3 Axis CNC Bed Milling Machine ProtoTRAK SMX Control Spindle: 5HP – Programmable 40 – 5000rpm 2 Ranges 40 – 600 & 300 – 5000rpm ISO40 Quill Dia 105mm Year of Manufacture 2008 Table: 1370 x 355mm 4 0ff T Slots T Slot size 15.9mm Max load 600kgs Travel: X – 787mm Y – 508mm Head Vertical (Z) – 500mm Quill (Z) 127mm Dims without travel – 1905 x 2069 x 2225mm Dim with travel – 2758 x 2869 x 2490mm Weight 2430Kgs Power Requirements 22A Air Requirements 6bar Tjdpozuxn Tsfx Airod For sale with Jet Machinery Ltd Jet Machinery Stock No: #79245 Machine Serial Number: 10731 Cost: £17,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: new, functionality: fully functional, Year of construction: 2025, machine/vehicle number: 25072, control type: NC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: DELSY EASYCOM, controller model: EASYCOM 4AXIS, number of rollers: 4, roller (bottom) diameter: 140 mm, roller (top) diameter: 160 mm, side roll diameter: 120 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 8 mm, sheet thickness brass (max.): 8 mm, sheet thickness copper (max.): 8 mm, overall weight: 2,900 kg, total length: 3,000 mm, total width: 1,000 mm, total height: 1,200 mm, input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4 Roll plate bending machine dual initial pinch MG Italy 2000X6mm Mode CNC EASYCOM 4-AXIS NEW MACHINE serial no. 25072 Capacity: -Width of plate: 2000 mm -Thickness plate roll 6 mm -Plate pre-bend 4 mm Tjdpfxs Ahgwie Airod Rolls -useful width mm. 2050 -Top roll mm. 160 - Lower roll mm. 140 Configuration installed: hardened rollers, surface smooth finishing for all kind of plates and stainless steel Prebend process in manual and automatic full rounding no-flat plate ends Conical plate rolling cones and reducers hydraulic control dual initial pinch Driven rolls rotation hydraulic powered with axial gear unit plate dragging and forming . Console electric CNC with centralized commands joysticks , 4-axis position programming and readout. CNC controller interface touch screen 15”, 4 axis teach-in programming mode, infinite memory storage for automatic plate roll. On screen digital position readout of the 4 rollers for automatic programmable control and/or manual bending use by operator. Opening hydraulic drop-end machine front for the unload of fully round bending. Variable working speed fast-slow controlled Safety installation with emergency stop. Instruction manuals for operation and service.

Condition: excellent (used), Year of construction: 2010, XYZ SMX 5000 3 Axis CNC Bed Milling Machine ProtoTRAK SMX Control Spindle: 7.5Hp – Programmable 70 – 5000rpm ISO40 Quill Dia 105mm Manufactured 2008 Table: 1930 x 355mm 4 off T Slots size 15.9mm Max load 850kgs Travel: X – 1524mm Tedpey Ni Ivjfx Airod Y – 596mm Z – 584mm Dims: W - 5805mm D – 2530mm H – 3143mm Weight - 3100Kgs For sale with *Jet Machinery Ltd* Stock No: 79199 Serial No: 11273 Price: £24,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Year of construction: 2010, condition: used, CNC control system FIDIA with handwheel; travel ranges: X-axis approx. 11,500 mm, Y-axis approx. 1,550 mm, Z-axis approx. 2,250 mm; clamping table, length x width x height, 2 pieces, each approx. 2,000 x 2,000 mm; table load max. 1,000 kg; milling spindle, spindle power S1 / S6 approx. 7.4 kW / 12 kW, spindle speed 16,000 rpm, tool holder HSK 50A, B- and C-axis +/- 210° / +/- 104°, feed rate X-, Y-, Z-axis up to 16 m/min, axis acceleration m/s², machine footprint approx. 14,000 x 2,600 x 3,650 mm, with self-built table, total weight approx. 13,500 kg; NOTE: Fully functional condition, machine has already been disassembled and stored. The machine is already located at a different location in Kartonstraße 2, D-88255 Baienfurt. Free loading FCA D-88255 Baienfurt. Tedps Af Nl Usfx Aired

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, operating hours: 3,000 h, number of axes: 5, number of slots in tool magazine: 24, We are offering this well-maintained, young COSMEC 5-axis CNC milling machine, model CONQUEST 515, from 2021. The machine is currently in production and operates on a single-shift basis. It can be inspected and tested while powered on. - Training/instruction for your employees can be provided at our facility before the machine is disassembled. - Year of manufacture: 2021, commissioning date: 05/2021 - Work table: 4000mm x 1500mm - OSAI control system - 24-position tool changer (2 disks with 12 tools each) - Portal clearance: 500mm - 5-axis swivel head: 18KW, 500 - 24,000 RPM - NC-controlled extraction hood - Bumper safety system - Control cabinet with air conditioning unit - Mobile control panel - Central lubrication system - Vacuum pump: 250 m³/h - Approximately 24 HSK63F tool holders - Automatic tool length measurement Tsdpezukurofx Aired - Nesting table - Nesting CNC milling machine - Swivel machining is possible The price is "Ex Works". We will gladly assist with disassembly and loading. Similar to Reichenbacher Vision or Homag CNC. If you have any questions or would like to arrange a viewing, please feel free to contact me by phone or email.

Condition: used, Year of construction: 2017, machine/vehicle number: STA00197, XYZ CT52 2 Axis CNC Lathe Box Ways Slides Siemens 828D CNC Control Swing over bed 400mm Max’ machining dia. 200 mm Tsdpozkbirsfx Airsd X-axis stroke 115mm Z-axis stroke 290mm Spindle speed 5000 rev /min Spindle Bore 61mm Max’ bar work dia. 52mm 12 Station VD130 Turret Tailstock stroke 90 mm Rapid traverse rate 20 m/min X & Z Axis Cutting Feed rate 10 m/min X & Z Axis Machine Weight 2500Kgs Machine Size 1700 x 1240mm Manufactured 2017 Machine supplied with: 3 Jaw Chuck Power Chuck Tool Setting Probe Parts Catcher Chip Conveyor Auto Lubrication High Intensity Machine Light Toolbox For Sale With Jet Machinery Ltd Jet Machinery Stock Number:79265 Machine Serial Number: STA00197 £29,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, 4-axis CNC milling machine Manufacturer: Quick Type: UA-481 New machine Tsdszvgmyspfx Airod Technical data: 380 V-3-phase Working area: 2100 x 3050 x 400 mm 9 kW HSD/HSK-F-63 spindle NC Studio control 10 linear tool changers Double-layer vacuum table with 6 zones Yaskawa servomotor 2 Becker pumps (250 m³/h) NC Studio control with German language Optionally available at an extra charge: - 10-position rotary tool changer on the gantry - 12-position rotary tool changer on the gantry - 2 pneumatic pressure rollers for multiple part clamping - Vacuum table with T-slot for manual fixing of components Other configurations available upon request.

Condition: used, Year of construction: 2001, machine/vehicle number: .01720, with CNC control, manufactured by FIDIA, type: C20, travel ranges: X-axis: 2400 mm, Y-axis: 2850 mm, Z-axis: 1000 mm, with automatic tool changer with 20 tool stations, with T-slot clamping plate, size: approx. 2000 x 1800 mm, coolant system. Tjdpfx Aie Af Nlmorjd

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, operating hours: 200 h, power: 4.5 kW (6.12 HP), input voltage: 380 V, type of input current: three-phase, travel distance X-axis: 1,800 mm, travel distance Y-axis: 4,500 mm, travel distance Z-axis: 1,050 mm, number of axes: 4, controller manufacturer: Syntec, total height: 3,600 mm, total length: 5,800 mm, total width: 2,440 mm, overall weight: 2,600 kg, table length: 5,400 mm, table width: 2,030 mm, For sale is a large-format, 4-axis CNC portal milling machine from Yishun, privately owned. With its enormous working area and 1050 mm Z-axis, the machine is ideal for the precise machining of large components made of foam (Ureol/Styrodur), plastics, wood, and aluminum (e.g., for mold making, boat building, or prototype construction). The machine has only been in operation for approximately 200 hours (year of manufacture 2016) and will be handed over in perfect mechanical and electrical condition. High-quality industrial components have been used throughout. TECHNICAL DATA & COMPONENTS: • Working area (X/Y/Z): 1800 mm x 4500 mm x 1050 mm • External dimensions: approx. 5800 mm x 2440 mm x 3600 mm (L x W x H) • Weight: approx. 2600 kg • Spindle: High-quality HSD spindle • Drives: Reliable, powerful Yaskawa servo motors Todpfozv U Tbex Aired • Controller: Syntec controller (machine can be moved on-site) • Guides & Mechanics: HIWIN linear guides, WMH rack and pinion with precise Rouist gears on the servo motors, ball screw in the Z-axis feed • Equipment: Integrated zero-point sensor for the Z-axis. Post-processors for HSMtec are available to a limited extent. • Reference: The finely finished aluminum milling sample produced on the machine, shown in the video, is available (see photos). • Note on scope of delivery: The machine does not have an automatic tool changer, dust extraction system, or vacuum clamping table. CONDITION & HISTORY: The machine has been unused but stored dry in a hall for the past few years. To consistently prevent the onset of surface rust due to natural humidity in the winter, the steel structure was recently preventively re-primed and painted. The guides are completely free of rust and have been regularly preserved. The machine runs perfectly mechanically and electrically. IMPORTANT INFORMATION REGARDING TRANSPORT & PICK-UP: 1. Private sale: The sale is made by a private individual, excluding any liability for defects, warranty, or right of return. No VAT can be charged. Purchased as seen and tested. 2. Loading assistance on-site: A suitable forklift will be arranged and can be used free of charge for loading onto your low-bed trailer or truck. 3. Transport options: The machine is primarily intended for self-collection. Delivery within a close radius (up to 50 km) is possibly possible after prior arrangement and upon payment of costs. If transport over longer distances is an issue, we will certainly find a joint solution after prior consultation or provide assistance in finding a freight forwarder. We are open to realistic price offers. An inspection and demonstration of the axes on-site in 91183 Abenberg are welcome after prior arrangement.

Condition: used, Year of construction: 2019, machine/vehicle number: 0191, For sale: Fenstek Emerald F260, a 4-axis CNC profile machining center from 2019, designed for the precise machining of long aluminum and plastic profiles. Thanks to its working range of up to 7,000 mm and the powerful 9 kW HSD spindle, this machine is particularly suitable for window, door, and facade production. The machine comes from a professional production environment, has been well maintained, is damage-free, and is fully operational. Inspection and a demonstration under power are possible. Todpfxjx R U Eis Aired Key specifications: - Axes: X / Y / Z / A, 4-axis interpolation - Control: PA8000 - Spindle: HSD, 9 kW - Maximum speed: 24,000 rpm - A-axis rotation: +90° to -90° - Working range: up to 7,000 mm, depending on the clamping configuration - Tool magazine: ISO30, 9 positions - Operations: milling, drilling, tapping, grooving, and chamfering - Suitable materials: aluminum profiles, light alloys, and uPVC An interesting machine for companies that want to machine long profiles flexibly and in a single setup.

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS CONTROL Control system: Deckel Contour 12 WORK AREA Table dimensions: 800 x 480 mm Number of table slots: 7 Travel range X-axis: approx. 400 mm Travel range Y-axis: 400 mm Travel range Z-axis: 400 mm TOOL HOLDER Tool holder: SK 40 MACHINE DETAILS Manufacturer: Deckel Maho Model: FP3-50 Machine type: CNC milling machine Tjdpfxo Adzl Rs Aired Serial number: 2860-151 Operating voltage: 400 V Frequency: 50/60 Hz Rated current: 24 A Length: 3,000 mm Width: 2,400 mm Height: 2,400 mm Weight: 3,000 kg

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS GENERAL INFORMATION Tjdo Adu Thspfx Aired Manufacturer: Maho Type: MH 800 P Machine type: CNC tool milling machine MACHINE DETAILS DIMENSIONS AND WEIGHT Length: 2,500 mm Width: 2,000 mm Height: 2,400 mm Weight: 1,000 kg

Condition: used, 4-axis CNC drilling and milling machine IXION Type 30 CNC W VMC, BAZ, machining center Year of construction approx. 1997, machine overhauled in 2020 Travel X: 600 mm Y: 350 mm Z: 600 mm Table size 800 x 400 mm T-slot spacing 75 mm Table load 300 kg Spindle holder SK 40 (tightening bolt DIN 69872 A) Spindle speed 20-5000 rpm Torque at the spindle max. 150 Nm Distance between spindle nose and table max. 660 mm Tsdpju Tln Nofx Aired Feed speed X, Y and Z 0 - 5000 mm/min. infinitely variable Rapid traverse speed X, Y and Z 15000 mm/min. Tool change time approx. 5 sec. Tool change time from chip to chip approx. 7.5 sec. Milling capacity in St 60 150 ccm/min. Drilling capacity in St 60 35 mm Thread cutting capacity in St 60 M24 Spindle motor drive power 5 kW (10 kW at 25% duty cycle) Mains connection 400 Volt, 50 Hz - CNC control Heidenhain TNC 415 with 12" TFT display - Electronic handwheel - RS 232 interface - 12-position tool changer - hydro-mechanical tool clamping - Rotary axis as dividing head on the table = 4th axis, MECATECNICA type DCN 250-8, jaws lathe chuck Ø 200 mm Speed approx. 25 rpm, transmission ratio 1:180 - Cabin lighting via 2x halogen spotlights - Chip conveyor with coolant pump - Switch cabinet fixed to the machine Space required for transportation Length 320 cm x width 230 cm x height 300 cm Footprint of the machine with chip conveyor L x W x H 3200 x 3100 x 3000 mm Weight of the machine 3100 kg Weight of the chip conveyor approx. 200 kg good condition

Condition: used, EMMEGI PHANTOMATIC M4L 4-axis CNC machining centre, manufactured in 2022, designed for machining aluminium, PVC and light alloy profiles. The machine is equipped with a high-speed electrospindle featuring an HSK-F50 tool holder, automatic A-axis rotation and a double tool magazine, making it ideal for milling, drilling, slotting, end milling and machining operations on multiple sides of the profile. MACHINE DETAILS Manufacturer: EMMEGI S.p.A. – Italy Model: PHANTOMATIC M4L Year of manufacture: 2022 Machine type: 4-axis CNC machining centre Certification: CE with original Declaration of Conformity TECHNICAL SPECIFICATIONS Axis Travel X-axis (longitudinal): 3,000 mm Y-axis (transverse): 274 mm Z-axis (vertical): 390 mm A-axis: automatic rotation from 0° to 180° Positioning Speeds X-axis: 56 m/min Y-axis: 22 m/min Z-axis: 22 m/min X/Y/Z axis acceleration: 3.3 m/s² Electrospindle Power: 4 kW (S1 continuous duty) Maximum speed: 20,000 rpm Tool holder interface: HSK-F50 Liquid cooling system Automatic A-axis rotation: 0°–180° A-axis rotation speed: 6,600°/min Machining Capacity X-axis longitudinal travel: 3,000 mm Usable working length with tool magazine: up to 2,815 mm, depending on configuration Extended-length machining capability: up to 5,630 mm, depending on machine configuration and operating conditions Multi-side profile machining capability MAIN FEATURES AND EQUIPMENT Double tool magazine Electrospindle with HSK-F50 tool holder interface CNC control system with operator monitor and keyboard Automatic A-axis rotation Pneumatic clamps for profile positioning and securing Fully enclosed safety guarding Pneumatic clamping system Technical documentation and operating manual Original CE Declaration of Conformity APPROXIMATE OVERALL DIMENSIONS Length: 3,707 mm Depth: 2,139 mm Height: 2,482 mm AVAILABILITY Todpfe Afnl Tex Airsd MACHINE AVAILABLE FROM JANUARY 2027

Year of construction: 2015, operating hours: 1,772 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: C117073, MMEGI PHANTOMATIC M4 – 4-Axis CNC Machining Center (2015) Italian-made CNC machining center for precision processing of aluminium profiles, suitable for windows, doors, curtain walls and industrial applications. Technical Specifications & Features: Year of manufacture: 2015 Operating hours: Only 1,773 h Tedpfxoz Rkkwj Airsd 4 CNC-controlled axes Spindle speed: Up to 20,000 rpm Automatic tool changer: 2 magazines × 4 tools (8 tools total) Pneumatic clamps: Automatically positioned by CNC Reference stops: 2 zero-position stops Control panel: Swivelling touchscreen display Barcode scanner for job identification Machine weight: 1,700 kg Rated power: 8.5 kW Power supply: 400 V / 50 Hz Operating air pressure: 6–7 bar Key Highlights: Low operating hours, automatic tool changing, CNC-controlled clamp positioning, swivelling touchscreen control panel and barcode scanner. Professional Italian-made machining center designed for precision and efficient aluminium profile processing.

Year of construction: 2007, condition: used, CNC control system HEIDENHAIN iTNC 530 with handwheel, travel distances: X-axis approx. 1,500 mm, Y-axis approx. 2,400 mm, Z-axis approx. 800 mm, table dimensions (length x width x height) approx. 2,500 x 1,500 x 530 mm, maximum table load 500 kg, milling spindle power 4 kW, spindle speed 6,000 rpm, tool holder 78/8 flange, feed rate X, Y, and Z axes 20 m/min, axis acceleration 1.5 m/s², machine footprint 6,000 x 4,000 x 3,900 mm, total weight approx. 8,000 kg, NOTE: Fully functional condition, regular maintenance performed by the machine manufacturer! The machine is already located at a different site at Kartonstraße 2, D-88255 Baienfurt. Free loading FCA D-88255 Baienfurt. Tede Af Nl Hspfx Airod

Condition: excellent (used), Year of construction: 2019, XYZ UMC-5X 5 Axis CNC Vertical Machining Centre Heidenhain iTNC 640 HSCI Control Model UMC-5X Control Heidenhain iTNC 640 HSCI X Axis Travel 600 mm Y Axis Travel 600 mm Z Axis Travel 500 mm A Axis Travel +120° / -120° C Axis Travel 360° Table Size 600 mm Diameter Maximum Table Load 600 kg Spindle Speed 24,000 rpm Direct Drive Spindle Taper BBT40 Rapid Traverse 36 m/min Feed Rate 1 - 36,000 mm/min Tool Changer 60 Station Automatic Maximum Tool Length 300 mm Through Spindle Coolant 70 Bar Machine Weight 9,500 kg Machine Fitted With: Heidenhain iTNC 640 HSCI CNC Control, 24,000 rpm Direct Drive High Speed Spindle (20kW S6 Rated), 60 Station Automatic Tool Changer, 70 Bar Through Spindle Coolant, Fixed Roof for High Pressure Coolant System, Renishaw RMP600 Strain Gauge Wireless Workpiece Probe, Laser Tool Setting System, Kinematic High Accuracy Machine Setup, Kinematic Reference Ball, Thermal Spindle Compensation, Linear Scales on X, Y & Z Axes, Direct Drive C Axis Rotary Table, Swarf Conveyor & Bin. Features: Simultaneous 5 Axis Machining Centre, Gantry Frame Construction, Direct Drive High Torque Rotary Table, High Precision Linear Roller Guideways, Dynamic Collision Monitoring, High Accuracy Machine with Linear Scales, Ideal for Aerospace, Medical, Precision Engineering & Complex Multi-Sided Components. For sale with Jet Machinery Ltd Tedpfx Aijzi Awhorod Jet Machinery Stock No: TBC Machine Serial Number: TBC Cost: £120,000.00 Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to inspect the machine prior to purchase. Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, Year of construction: 2011, travel distance X-axis: 730 mm, travel distance Y-axis: 730 mm, travel distance Z-axis: 880 mm, controller manufacturer: MORI SEIKI, controller model: M730BM, workpiece height (max.): 1,000 mm, workpiece diameter (max.): 800 mm, workpiece weight (max.): 500 kg, overall weight: 11,100 kg, Equipment: chip conveyor, With dual pallet, Mori Seiki M730BM control system. Todpfx Aoz Sqrkjirjd Workholding and tooling not included. AVAILABLE: late January/early February 2027.

Condition: good (used), Year of construction: 1990, HEIDENHAIN TNC-355 Tsdpfx Aiefg Ep Derjd Working travels 850x500x450mm Table size 1250x500mm Spindle taper 50 Spindle speeds 35,5-1800 rpm Misc.accessories MARCELS MASCHINEN CH

Condition: excellent (used), Year of construction: 2018, Clausing Colchester 4VSQ MLLPWR CNC Turret Milling Machine Acu-rite Mill Power 3 Axis CNC Control Table Size 1370 x 254mm Travels: X – 1050mm Y – 390mm Z (Quill) – 115mm Z (Knee) – 355mm Vari Speed Head Spindle Taper IS040 Spindle Speeds Low 60 – 500rpm Spindle Speeds High 55 – 4300rpm Weight: 1850Kgs 3 Phase Electrics Manufactured: 2018 Complete with: Vice Interlocking Table Guards Air Draw Bar Tooling Packaged (ISO40) Power Rise and Fall to Knee Auto Lube Worklight Coolant & Swarf Guards / Tray Tsdpfxjx Af I Aj Airod *For sale with Jet Machinery Ltd* Jet Machinery Stock No: #79028 Machine Serial Number: TC0015 Cost: £12,500.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, Year of construction: 2017, Manufacturer: DMG MORI, Type: DMU 75 monoBLOCK, Year of manufacture: 2017, Serial number: 12430007443, Operating hours: 28,368, Spindle hours: 11,627, Control system, Manufacturer: Heidenhain, Type: iTNC 530, 21" Operator terminal ERGOline Touchscreen, Tool changer, 63-position SK 40, Travel range X/Y/Z: 735 x 650 x 560 mm, Spindle speed max.: 12,000 rpm, Machine table clamping area: 1,000 x 650 mm, Coolant system, Oil mist extraction, Chip conveyor, Chip cart Tedpez Tlucjfx Airjd +++ IMPORTANT: This machine is part of an online auction! +++

Condition: new, 3-axis CNC milling machine Manufacturer: Quick Type: UE-481PL New machine Technical data: - PC with Windows 11 - CAD-CAM connection as desired - NC Studio control software - Heavy-duty machine base - Working area: 2100 x 3050 x 200 mm - Double-layer phenolic resin table - grid table - 9 kW HSD milling spindle with 24,000 RPM - 9-position HSD drilling unit - 90° rotatable sawing unit Tsdpfx Aiezvgmterod - 12-position linear tool changer - Automatic tool length measurement - Wireless control panel - 3 stops in X, 2 in Y - 2 units of 250 m3/h Becker vacuum pump - Automatic central lubrication - Safety via light curtain - Lifting table loading - Unloading table

Condition: used, Year of construction: 1989, Universal CNC Milling Machine MAHO MH 600 E2 Travel X: 600 mm Travel Y: 400 mm Travel Z: 450 mm Numerical Command CNC PHILIPS 432 Cone SA40 Spindle speed: from 20 to 4000 RPM Table size: 900 x 480 mm TravelSpindle sleeve travel: 80 mm Year of construction: 1989 1 lubricant tank Tjdpez Nx Hqefx Aired Voltage: 380 V Width: 2500 mm Depth: 2400 mm Total height: 2000 mm Weight: approx 3,5 T

Condition: used, Year of construction: 2013, functionality: fully functional, travel distance X-axis: 17,000 mm, travel distance Y-axis: 4,800 mm, travel distance Z-axis: 1,500 mm, table length: 16,000 mm, table width: 3,000 mm, spindle speed (max.): 3,000 rpm, rapid traverse X-axis: 12 m/min, rapid traverse Y-axis: 8 m/min, rapid traverse Z-axis: 8 m/min, distance between stands: 3,800 mm, type of input current: three-phase, position of the milling head: vertikal / Winkelkopf, rotational speed (max.): 3,000 rpm, distance table to spindle center: 2,300 mm, overall weight: 90,000 kg, spindle nose: ISO 60 / ISO 50 Adapter, spindle motor power: 60,000 W, Equipment: rotational speed infinitely variable, ➡️ WALDRICH COBURG CNC GANTRY MILLING MACHINE ⬅️ Heavy Duty Machining | Siemens 840D Retrofit | Ready for Production High-quality CNC gantry milling machine manufactured by Waldrich Coburg available for sale in very good condition. ✔ Machine under power ✔ Inspection & test run possible ✔ Siemens 840D retrofit (2013) ✔ New electrical system & cabinets ✔ New motors & drives ✔ Heidenhain glass scales on all axes ✔ Ideal for large part machining & heavy-duty applications Technical Data X travel: 17,000 mm Y travel: 4,800 mm Z travel: 1,500 mm Floor plates: 16,000 x 3,000 mm Distance between columns: 3,800 mm Distance table to spindle face: 2,300 mm Spindle power: 60 kW Spindle speed: 0.4 – 3,000 rpm Tool taper: ISO 60 / ISO 50 adapter Machine weight: approx. 90,000 kg Equipment Siemens 840D CNC control 2-step gearbox Right angle head WFU 250 with automatic indexing Right angle head WFU 500 with automatic indexing Rapid tapping Tool trolley with tool holders Steel way covers on X/Y axes 2 chip conveyors Perfect for: Heavy machining Machine building Energy industry Tjdpfxoy Rrb Ie Airsd Shipbuilding Steel & rolling mill industry Subcontract manufacturing 📍 Location: USA 🌍 Worldwide shipping can be arranged 📞 Please contact us for more information, videos, or inspection appointments.

Year of construction: 2005, condition: ready for operation (used), A Maka CNC 4-axis milling and drilling machine for plastic, wood and aluminum is available. Travel X/Y/Z: 2000mm/6000mm/250mm, C-axis: 360°, rapid traverse X/Y/Z: 45m/min/45m/min/24m/min, spindle mount: HSK63, spindle power: 12kW, spindle speed: 24000rpm. Tool places: 12, angle head places: 3, machine dimensions X/Y/Z: 12000mm/5700mm/3200mm, control: BWO 920, documentation available. On-site inspection is possible. Tsdpfx Aisvmq Tvsrod