Used Die Forging Press for sale (37,771)

Condition: excellent (used), Year of construction: 2016, operating hours: 27 h, SBL 1060 SE Year: 2016 Sheet feeder: Manual non-stop pile feeder Material range: Paper and board from 470 × 350 mm to 1060 × 760 mm Max cutting format: 1050 × 740 mm Min sheet size: 470 × 350 mm Max sheet size: 1060 × 760 mm Max cutting pressure: 300 tons Material thickness: 0.1 – 2 mm (corrugated/laminated max 4 mm) Min gripper margin: 9.5 mm Max inside chase size: 1155 × 852 mm Cutting plate size: 1076 × 756 mm Max speed: 8,000 sheets/hour Power consumption: Total 32 kW (22 kW + 10 kW for lower plate heating) Machine dimensions (L×W×H): 5,900 × 5,700 × 2,615 mm Max pile height – feeder (with pallet): 1,750 mm Max pile height – delivery (with pallet): 1,450 mm Feeder Section Hodpfxewypp Ij Aabjfn - Pneumatic feeder table - Non-stop manual feeder system - Anti-static system - Pre-pile device - Manual suction group adjustment - Micrometric suction adjustment - Motorized side pile adjustment - Suction belt feeder table - High-pressure lubrication pump - 2 pneumatic side register guides - Electronic control of front and side register Cutting/Embossing Section - Automatic pressure adjustment up to 300 tons - Preparation and introduction table for die frames in platen - 2 quick-lock die chase frames with bottom plate - Pneumatic locking of the chase and lower supporting plate - Centerline System - Micrometric system - Heated lower support plate (24 mm) - Cutting plate: 4 mm - Compensation plate: 3 mm - Archiveable 1 mm thin cutting plate Stripping Section - Quick lock for upper and central stripper frames - 2 standard upper stripper frames - 2 standard lower stripper frames - Double accessory kit for lower stripper prep (pins, bars, clamps, etc.) Delivery Section - High-pile automatic non-stop delivery with conveyor - Guillotine for automatic removal of gripper margin waste - Sheet deceleration device - Tab insertion device

Condition: new, Year of construction: 2025, functionality: fully functional, stroke length: 1,750 mm, input voltage: 380 V, table width: 1,500 mm, table length: 2,000 mm, clamping force: 3,000 kN, table load: 14,600 kg, 300T Die Spotting Press Clamping Force:300T Lifting Force:82T Hfsdpfjug Ughex Aabjn Worktable Size:2000*1500mm Max. Daylight:1750mm Min Daylight:0mm Stroke of Bolster:3000mm Overturn capacity:7.3T Overturn Degree:180° Motor Power:30Kw

Condition: good (used), Year of construction: 2008, total height: 5,400 mm, installation height: 500 mm, table length: 2,000 mm, table width: 1,100 mm, pressing force: 250 t, overall weight: 57,000 kg, product height (max.): 4 mm, sheet thickness steel (max.): 4 mm, space requirement length: 4,800 mm, space requirement width: 2,750 mm, controller manufacturer: SIEMENS, controller model: S7 300, power: 95 kW (129.16 HP), load capacity: 2,000 kg, coil outer diameter: 2,000 mm, coil weight: 2,000 kg, coil width: 300 mm, number of straightening rollers: 7, product width (max.): 300 mm, sheet thickness (max.): 4 mm, tool height: 500 mm, CONTROLS .. electronic controls SIEMENS S7 300 PRESS DESIGN .. drive system: eccentric / crank .. openings in uprights: yes .. number of suspensions: 2 .. table cushion: no .. quick die change system: yes PRESS FORCES .. total force (nominal): 250 to PRESS TABLE .. table surface (left-right): 2000 mm .. table surface (front-back): 1100 mm .. height above floor level: 1105 mm .. opening in bed (left-right): 1700 mm .. opening in bed (front-back): 305 mm SLIDE .. table surface (left-right): 2080 mm .. table surface (front-back): 1000 mm .. stroke rate (max.): 120 /min SLIDE (MECHAN. PRESS) .. slide adjustment: 120 mm .. stroke adjustment: yes .. stroke min.: 20 mm .. stroke max.: 180 mm Hfodpfx Aoxnwabsabsn TOOL ASSEMBLY DIMENSIONS .. shut height (stroke down, adjustment up), BDC: 500 mm .. distance between columns (H-frame): 2055 mm .. passline opening (free passage in side columns): 810 mm DECOILER .. sheet width max.: 300 mm .. coil weight max.: 2 to .. max. diameter of coil: 2000 mm .. mandrel expansion range up to: 550 mm LEVELLER UNIT .. sheet width max.: 310 mm .. number of leveller rolls: 7 .. diameter of leveller rolls: 80 mm STRIP-FEEDER .. feeder type: roll feeder .. sheet width max.: 200 mm .. sheet thickness max.: 4 mm .. speed max.: 120 m/min ELECTRICAL SPECIFICATIONS .. total power consumption: 95 kW .. mains voltage: 400 V .. mains frequency: 50 Hz DIMENSIONS / WEIGHTS .. space requirements -left/right-: 4800 mm .. space requirements -front/back-: 2750 mm .. total height: 5400 mm .. total weight approx.: 57000 kg ATTACHMENTS (PRESSES) .. decoiler: yes .. leveller unit: yes .. European CE standards: yes Machine hours: 20,391 h (operating hours) Adjustment strokes: 20, 39, 69, 99, 125, 148, 165, 175, 180 mm Equipment: - External connecting rods for high tilt stability - Hydraulic overload protection - Press force monitoring - Temperature sensors at the bearing points - ABS AHM 2.0T decoiler (1999) - PBK RSD 8/6/300 straightener (2010) - Loop belt control - LW-060-02 roller feed (2008) - Advanced central lubrication system - Press force monitoring - Temperature sensors at the bearing points - Hydraulic tool clamps - Spring-loaded machine feet - Optional: Bilz air springs for an additional €7,000

Condition: ready for operation (used), Year of construction: 2005, Bobst SP 104 ER Die-cutter Diecutter with stripping and blanking station Hjdpfxswgz H Eo Aabofn Technical specifications: Paper min. 90 g/m2 Cardboard max. 2000 g/m2 Corrugated board max. 4 mm Min. sheet size: lxw 350 x 400 mm Max. sheet size: lxw 740 x 1040 mm Max. dimensions of cutting die: Max. lxw 725 x 1040 mm Cutting force: 250 tons Running speed: max. 8.000 s/h. Centerline for job quick-change Adjustable centering at the stripping and at the delivery, Bobst-Electronic machine operationg system C.U.B.E. : (Control Unit Bobst Electronic) Non Stop Feeder, Steel plate, Double Sheet Sensor, Left hand pull lay, Right hand pull lay, Micrometic adjustment, Centerline, Double Action Stripper, Blanking Station, Quick lock stripping frame,

Year of construction: 2005, condition: excellent (used), machine/vehicle number: 47885/05, pneumatic punching of window profiles Hsdpfx Asff Apieabefn Stroke 20 mm

Condition: used, Pressure total: 800 ton Stroke: 400 mm Slide adjustment: 160 mm Shut height (stroke down, adjustment up): 800 mm Table surface area : 1000 x 1000 mm Slide area: 1000 x 1000 mm Number of strokes: 18 s.p.m. Distance between the guardrails: 850 mm Free frontal opening L-R: 1050 mm Ejector in table: 100 ton Lower ejector stroke: 400 mm Required power: 132 kW Hjdpfxeuqh Rvo Aabsfn Standard configuration Machine was overhauled in 2017 / 2018

Year of construction: 2022, condition: new, Pressure: 400 t table length: 3000 mm table width: 2000 mm table load max .: 50 t distance between the work tables : min. 400 / max. 2800 mm Hedpfx Aasfn Efpebefn top tool foldable: 180 degrees Dimensions L x W x H: 7600 × 5670 × 7850 mm Total weight (without operating materials): 85 t Motor power: 44 kW

Condition: used, Year of construction: 2014, functionality: fully functional, year of last overhaul: 2024, Rotary Die Cutter RD-4055 (2014) Used * Configuration: - FFU-4055 Hfodpfxow S Uane Aabsn - RD-4055 - SPC-4055 * Total Counter: 203,076 Sheets * Condition: Excellent (Repaired) * Language: Japanese * Ready to Use * Specifications Paper Feed System - Air Hole Belt Paper Size (Before Processing) - Maximum: 400mm (W) x 550mm (L) - Minimum: 200mm (W) x 275mm (L)

Condition: used, CNC Press Brake AMADA Type HFBO 50 x 2000 Serial No. HFBO 50 20 S60906 Year of manufacture: 1996 Press brake with 8 axes - CNC control Operator II Pressing force: 50 tons Working length: 2090 mm Stroke: 200 mm Frame depth: 420 mm Distance between side frames: 1660 mm Max. tool installation height: 460 mm Table width: 60 mm Table height above floor: 910 mm Motor power: 4.5 kW Mains connection: 400 Volt, 50 Hz, 20 Amp. - 8-axis CNC control Operator II (Y1-Y2 / X1-X2 / Z1-Z2 / R1-R2) - 2 freely programmable backgauge fingers, movable laterally and in height (Z1+Z2+R1+R2) - Press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and/or two-hand control panel - Mechanical lever-style tool clamping for the upper tool (5 AMADA Expert, 5 UKB 50.667 H=120 mm) - Tool holder for lower tool, 60 mm wide - 11-piece upper tool set, 30°, total length 1675 mm - consisting of: 1x 835 / 1x 300 / 1x 165 / 1x 50 / 1x 45 / 1x 35 / 1x 20 / 1x 15 / 1x 10 / 2x 100 mm (end pieces) in length - 2-piece lower tool, 88° - V8, total length 1250 mm - consisting of: 1x 835 / 1x 415 mm in length - Indicated operating hours: 30,537 h Hsdpfxew Iq Ugo Aabefn - Operating manual, electrical diagram, spare parts book included Weight: 4,700 kg Good condition

Condition: ready for operation (used), Fully Automatic Flatbed Die-Cutter, Non-Stop Feeder, Automatic Vacuum Plate, Hodpfxjwly D Ho Aabofn Double Sheet Cleaning Station, Turn Die Cutting Frame, (Batch Delivery) Non-Stop Delivery With Belt, Cutting Force 300 TON, Up to 4.500 Speed/H, Working With Corrugated Cardboard Of Thickness Max. 9mm, Min. 0,9mm, Format: Max. 1055x1575mm, Min. 400x600mm, Standard Accessories Bobst SPO 1575 EG 1980, fully rebuilted 2015, chain changed 2024.

Condition: used, Year of construction: 1979, pressure 18 t diameter 250 mm stroke 150 mm distance between columns 210 mm max. distance table - ram 400 mm Hfsdovzxp Iopfx Aaben power capacity 5,5 kW weight of the machine ca. 1,1 t dimensions of the machine ca. 1,0 x 1,0 x 1,8 m hydraulic die-hob press with oil-hydraulic drive, controllable dependent on pressure/time as is where is, WITHOUT putting into operation Price for commissioning (in given condition) on request

Condition: good (used), Drossert ST 3B Cauhe Die cutting machine The machine is fully operational, ready for production. Weight 3500kg Power supply 380V Production under the Drossert Maschinenbau GMBH Germany brand by the Cauhe factory in Spain. Equipment: Hfsdeu Umcqspfx Aabsn – pneumatic clutch and brake – console – 3 operating modes: single, continuous, with time delay on opening – central lubrication – additional safety covers – hard sheet metal for pressure

Condition: used, Year of construction: 1981, stroke 610 mm strokes per minute 12 daylight - vertical 1450 mm Hjdpfxow Sya Hj Aabofn adjustment des Stößels vorhanden mm table size 2400 mm x 1370 mm die cushion Nicht vorhanden oder nich Mp 1500 unter Strom bis Oktober

Condition: excellent (used), Year of construction: 1976, functionality: fully functional, Multi-stage cold press with a shearing device and four successive press stations Hjdpfx Aasp Au Ayebefn

Condition: new, Year of construction: 2025, functionality: fully functional, Machine Model:HMG-200JM1815 1:Servo hydraulic motor 2:Magnetic table Specification: Clamping force: 2000KN Hfodpfxjug T Rxo Aabon Table size:1800*1500mm Maximum mold weight:20000 Kg Machine weight:32000kg Machine size:6200*2750*5800mm

Condition: ready for operation (used), Year of construction: 1983, BOBST SPO 1600 Max Speed 5000 per hour Year 1983 Max lenght 1075mm Max width 1580mm Fully reconditioned by Bobst 2015 Hfedpfxsxcayys Aaben Central line

Condition: used, Year of construction: 1983, nominal force 2500 t stroke 600 mm cycle time 13 - 18 s distance between columns 1720 mm Distance table/ram, max. stroke up, adjustment up 2600 mm table surface area 1720 x 1800 mm allowed max. force 4000 t blow die to die 5000 t ram surface 2100 x 1320 mm capacity of ejector in table 40 t ejector stroke in table 250 mm ejector surface area in table 900 x 820 mm capacity of ejector in ram 6 t ejector stroke in ram 40 mm spindle diameter 425 mm power requirement 900,0 kW weight 335,0 t Dimensions (WxDxH) 3,4 x 4,6 x 9,7 m height over floor 8,3 m Hfedpfxswmf Tvs Aabon fully automated forging line / spindle press with automation for the production of flanged shafts for hot forming only with reversible AC motor, pneumatic brake, plate ejector in table (40 t / 250 mm), ejector in ram (6 t / 40 mm), lifting device for repositioning, marking, tool change, insertion device, tilting device, loading and unloading arm, rotary table, circular oil lubrication, centralised grease lubrication cycle time approx. 13 - 18 s as is where is, WITHOUT putting into operation

Condition: good (used), Atom SE 20C hydraulic arm press The device is in perfect condition, ready to work. It is ideal for die cutting difficult materials, especially used in the leather and printing industries. Possibility of using typical leather and bookbinding dies. Cuts paper, cardboard, leather, plastic, etc. Pressure 20t Power supply 380V Table dimensions: 900mm x 430mm Hfjdpfx Aajwundtsbon Hammer dimensions: 370mm Max stroke 90mm Engine power 0.9kW Weight 630kg Two-handed control.

Condition: new, Application: Cold Forging of MS/Copper/Al/Alloy Steel / Sizing / Coining / Extrusion / Upsetting Required Press Capacity (Tons): 100 to 5000 Tons and above No. of Stations: Multiple, as per Customer Requirements Daylight Opening (mm): up to 2500 mm and above Stroke (mm): up to 2000 mm and above Pressing Stroke (mm): As per Customer Requirements Hfodpfx Aaoxayy Usbon Shut Height (mm): As per Customer Requirements Bolster Size (L × W mm): up to 5000 mm and above Moving Bolster: Yes, as per Customer Requirements Type of Press: 4-Pillar / Frame Type / Column Type Approach Speed (mm/sec): 500 mm/sec and above Pressing Speed (mm/sec): 10 - 50 mm/sec and above Return Speed (mm/sec): 400 mm/sec and above Automation Level: Manual / Semi-Automatic / Fully Automatic Servo Based System: Yes, Available PLC / HMI: Yes, Preferred Brand if any Ejection System: Yes, Hydraulic / Mechanical / Air Safety Standards: CE / ISO Special Accuracy: JIS B6403 Grade 1 Data Recording / SCADA Connectivity: Yes, Available Special Features: As per Customer Requirements Other Utility Equipment: As per Customer Requirements Robotic Integration: Yes, Available IoT Integration: Yes, Available

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition Hsdpfx Ajwbvmijabefn

Condition: ready for operation (used), Year of construction: 1985, Bobst SP 102 CER - Perfect condition available immediately Year 1985 Max.Size: 1020x720 mm Min.Size: 400x350 mm Max.Speed: 8000 Sh/h Max. Cutting force: 250T Paper: min. 80 gr/qm Cardboard: max. 2000 gr/qm Centerline Feeder Non-Stop Autom. Non-Stop with Sheet inserter Hedpfxjwathho Aabofn Side guide Quick Lock system

Condition: new, Application: Hot Forging of MS/Copper/Al/Alloy Steel / Trimming / Cup Forming / Piercing / Extrusion / Upsetting Hfodpoxayyhsfx Aabon Required Press Capacity (Tons): 100 to 5000 Tons and above No. of Stations: Multiple, as per Customer Requirements Daylight Opening (mm): up to 2500 mm and above Stroke (mm): up to 2000 mm and above Pressing Stroke (mm): As per Customer Requirements Shut Height (mm): As per Customer Requirements Bolster Size (L × W mm): up to 5000 mm and above Moving Bolster: Yes, as per Customer Requirements Type of Press: 4-Pillar / Frame Type / Column Type Approach Speed (mm/sec): 500 mm/sec and above Pressing Speed (mm/sec): 10 - 100 mm/sec and above Return Speed (mm/sec): 400 mm/sec and above Automation Level: Semi-Automatic / Fully Automatic Servo Based System: Yes, Available PLC / HMI: Yes, Preferred Brand if any Ejection System: Yes, Hydraulic / Mechanical / Air Safety Standards: CE / ISO Special Accuracy: JIS B6403 Grade 1 Data Recording / SCADA Connectivity: Yes, Available Special Features: As per Customer Requirements Robotic Integration: Yes, Available IoT Integration: Yes, Available

Condition: used, Frame die-cutter - Swivel frame die-cutter - Flatbed die-cutter - Platen die-cutter - Eccentric press Punch + feed for the use of bandknife punching tools Flatbed die cutter HELMERDING type PSH 25 Com. No. EP 97784 Machine. No. 6073 Year of construction 1998 Compressive force 25 ton. Clearance between the tie rods 700 mm Table surface = installation space 800 x 670 mm Hfjdpjdzqmzefx Aabon Table surface = installation frame width 510 x depth 440 mm, plate thickness 20 mm Plunger surface 800 x 670 mm Hole in the table 490 x 420 mm Plunger stroke 45 mm Ram adjustment travel 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min. Motor power 15 kW Mains connection 400 Volt, 50 Hz - Controlled drive for infinitely variable stroke rate - Pneumatic clutch-brake combination - ram compensation cylinder - VOGEL automatic central lubrication system - solid base plate with 4 swinging elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons good condition The machine was formerly used for cutting out cardboard blanks. Ideal for cutting out non-woven fabrics or similar for breathing masks.

Condition: ready for operation (used), Year of construction: 2006, Bobst SP102-BMA Foilmaster Equipped with: Fully Automatic Feeder Double Sheet Control Centre Line Hot Foil Unit 2 x honeycomb chase 2 x die cutting chase 16 Independent Heating Zones Foil Advance Shafts Automatic Delivery Elevated (High Pile) Specification: Sheet Format Max: 720mm x 1020mm Sheet Format Min: 350mm x 400 mm Working Material Paper/Solid Board: 80-2000gr Corrugated Board: "E" and "B" - max. 4mm Hedowgz Rkopfx Aabjfn Gripper margin: 9-15mm Stamping Format: Max 680mm x 1010mm Max speed: 7,500 p/h

Condition: used, 2-station notching machine and folding machine EUROMAC type Multi 220/6R Press brake, press brake, notching machine Hfedpfxsmck Ryj Aaben Serial no. M11941298 Year of manufacture 1998 Cutting capacity 6 mm steel at 45 kg/mm2 4 mm for stainless steel Station I (notching) Notching angle 60° to 140° (with special blade from 30° to 140°) Knife length 220 mm Table size 950 x 640 - Manual angle adjustment via hand wheels - Notching angle with built-in blade set from 60° to 140 - Hydraulic clamping of the upper and lower knives - Automatic cutting gap adjustment - sheet hold-down device - Scaled measuring tapes embedded in the table - stop rails with angle adjustment - Operation via foot switch Station II (die bending device) Pressure force 18 ton Table size 950 x 340 Working height 1100 mm - stepless lifting speed - Infinitely adjustable stroke limiter - Stroke adjustment up to 30 mm working stroke - Reversible prism with 4x 90° prisms, length = 415 mm - 90° upper tool, length = 415 mm Motor power 4 kW Mains connection 400 Volt, 50 Hz Space requirement L x W x H 1150 x 1050 x 1460 mm Weight approx. 1000 kg good condition