Used Leit Spindle Lathe for sale (14,521)

Condition: used, Year of construction: 2000, used CONDOR AC, partially overhauled Centre height: 165 mm Between centres: 750 mm Spindle bore: 40 mm Spindle speeds: 22–2,800 rpm, infinitely variable - Quick-change tool post size B Dedpfx Aox E Um Nofpjun - WEILER DZ-V digital readout - Hollow spindle stop - Fixed steady rest - 7 Multifix tool holders - Flat splash guard - Electrically interlocked chuck guard - Change gears and various soft jaws The machine is partially overhauled: - Bed slide: guideways re-coated and hand-scraped, gibs and lower guide strips adjusted - Cross slide measured and aligned on bed slide; cross slide dovetail guide newly scraped, gibs adjusted and scraped - Top slide newly scraped and gib matched - All measuring scales overhauled and cables replaced The machine is located in our showroom at 71334 Waiblingen-Beinstein and is immediately available. For details on equipment, please contact us.

Condition: used, machine/vehicle number: 11756, second-hand WEILER LZ 280 sliding headstock and sliding headstock lathe center height 125mm center width: 800mm spindle speed approx. 26-2000 rpm 1 x three-jaw lathe chuck Ø 125mm with inner and outer jaws, brand new Multifix size A with 2 interchangeable holders Emergency stop/switch unit, rear chip guard, all change wheels present, drive disk, Dusdpevd Dbnefx Afpon storage tray, machine light, new socket, 15 collets from Ø 3.5 - 18.5 mm, collet clamping tube, fixed point and MK 2 sleeve for clamping tube, bed stop, chuck protection cover, various turning tools and operating instructions. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. A viewing of the machine is possible by arrangement.

Condition: used, machine/vehicle number: 1717, Used lead and feed screw lathe WEILER PRAKTIKANT Centre height: 140 mm Distance between centres: 500 mm Spindle bore: 36 mm Spindle speeds: 42–2,000 rpm Dsdjuqb Emopfx Afpjun Equipped with RSF 3-axis digital readout, 1 pc 3-jaw chuck Ø160 mm, Chuck guard electrically interlocked, With Multifix toolpost size A with 3 holders Lever-operated collet device with 15 collets. The machine is located at our facility in 71334 Waiblingen-Beinstein and is immediately available. Viewing of the machine is possible by prior arrangement.

Condition: good (used), functionality: fully functional, spindle bore: 36 mm, center height: 155 mm, turning length: 800 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 25 rpm, Used Weiler Condor lathe, No. 7939, Dedjv R Tdxepfx Afpeun Center height 155mm, Center width 800mm, Spindle speeds 12-2800 rpm, spindle bore 36mm Accessories: 1x RÖHM three-jaw chuck Ø 160mm, Multifix base body size B with 2 inserts, keyless drill chuck, live center, and coolant system. The machine is in stock at our facility in 71334 Waiblingen-Beinstein and is available immediately.

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 1824 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feed rates from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake >> 2 emergency stops On request: covers for the guide. and feed spindle Dedpfx Afsvrcqdjpeun About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. Even at high speeds, the Weiler runs very quietly. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 2020 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feeds from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametrical pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake Dsdpfjvrckqsx Afpsun >> 2 emergency stops On request: covers for the guide. and feed spindle About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. The Weiler runs very quietly even at high speeds. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and feed spindle table lathe in excellent condition! Dusdpfx Afjv Tyzcopjn Technical specifications: >> Machine no. 2801 >> Center height 120 mm >> Center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short-taper spindle head DIN 55027 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x Röhm 125 mm three-jaw chuck with 4 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increments of 1 mm Drawbar >> Multifix size A with 4 tool holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle cover >> Clamping tool About the machine: Offered is a Weiler Primus table lathe with guide rail and drawbar in very good condition. The machine is fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. The Primus comes from a state-owned company where it was used little. This newer generation of Weiler lathes is very user-friendly, and surfaces can be produced with a polished finish. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition. (The base cabinet is included; the machine is not bolted to the machine.) A digital display is available for an additional charge.

Condition: used, functionality: fully functional, Weiler Matador VS-2 guide and feed spindle lathe Technical data: >> Year of manufacture approx. 1970 Machine no. M1012 >> Center height 140 mm >> Center width 500 mm >> Speed: 30 – 3550 rpm >> Spindle passage 36 mm >> Short taper spindle head DIN 55022-5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.010 to 1.184 mm / rev Dodpfx Afsvv Etvopeun >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 15 mm >> Weight approx. 700 kg >> Length 1.4 m, height 1.2 m, depth 0.55 m Accessories and equipment: >> Collet device 32 collets (set is not complete) with holder >> 1 three-jaw chuck 1 set of jaws >> 1 four-jaw chuck 1 set of jaws >> Mulifix size A with 2 steel holders >> Change gears >> Bed stop About the machine: A used Weiler Matador VS-2 is offered in a fully functional condition. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Emcomat 17D Lead and Feed Screw Lathe with 3-Axis Digital Readout K&C New from Training Workshop Excellent Condition!!! Technical Data: >> Year of manufacture: approx. 2000 >> Machine no.: D3F H1 010 >> Centre height: 170 mm >> Swing over bed: 340 mm >> Swing over cross slide: 190 mm >> Turning length: 700 mm Dujdpfx Afswvuf Tspon >> Spindle speed: 4 speed ranges, stepless from 35 to 3000 rpm >> Tailstock quill stroke: 120 mm >> Tailstock: MT3 >> Spindle bore: 50 mm >> 20 longitudinal feeds: 0.045 – 0.787 mm/rev >> 20 cross feeds: 0.023 – 0.406 mm/rev >> Required floor space approx. (L x D x H): 1.600 x 0.9 x 1.3 meters >> Weight: approx. 730 kg Equipment and Accessories: >> 3-axis digital readout from K&C, new, with 12 months manufacturer’s warranty and operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 piece three-jaw chuck NEW 160 mm, 2 sets of jaws >> Multifix B toolholder with 2 tool pockets >> Chip guard >> Coolant system About the machine: Offered here is an Emcomat 17D lead and feed screw lathe, approx. year 2000, in very good condition. The machine is of course fully functional. The bedways are in excellent condition. The Emco is equipped with a new 3-axis digital readout from K&C and a new three-jaw chuck. Take the opportunity to inspect the machine under power on site and see the condition for yourself.

Condition: like new (used), functionality: fully functional, Weiler center lathe model Condor B lead and feed spindle lathe with 3-axis digital readout from K&C NEW Geometrically overhauled with acceptance certificate for tolerances of new machines !!! Technical data: >> Machine no. 90-1495 >> Center height 165 mm >> Center width 750 mm >> Spindle speed : from 22 to 2800 rpm >> Spindle clearance 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.015 to 0.46 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg Dodpfjvambcex Afpoun >> Spindle brake can be activated >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and equipment: >> 3-axis digital readout from K&C New , 12 months manufacturer's warranty with operating instructions Functions : Switching mm/inch , Coordinate selection ABS/INC , Halving of the display value , Reference mark , Tool programming 200 pcs. , Cone calculation , Radius / diameter , Quick zeros , Switching the counting direction , >> Collet chuck device, collets NEW from 3 to 26 mm 1 mm increasing >> Three-jaw chuck 160 mm with 2 sets of jaws NEW >> Mulifix new size A with 2 steel holders new >> Bed stop >> elec. Chuck guard NEW >> Machine lamp LED New >> Rear panel >> Operating instructions >> Coolant device >> Machine feet To the machine : We are offering a Weiler Condor B lead and feed spindle lathe in a geometrically overhauled condition, absolutely as good as new. The guides are newly ground and scraped. With acceptance according to test protocol. A very nice machine with electronic spindle protection. The accessories collets, chuck, Multifix are new. Spindles, spindle nuts, bearings, belts, wipers have been renewed. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: like new (used), functionality: fully functional, Weiler Praktikum 160B precision center lathe 3-axis digital display K&C NEW. Reconditioned with acceptance certificate for tolerances of new machines Technical data: Dujdjvrdlcopfx Afpen >> Machine no. 87 160 760 >> Center height 160 mm >> Center width 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle passage 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.02 to 0.63 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake can be switched on >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching the counting direction, >> Collet device New, collets NEW from 3 to 25 mm, 1 mm increasing >> Three-jaw chuck 160 mm New with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Electronic spindle protection >> Machine lamp LED New >> Machine feet NEW >> Splash guard >> Operating instructions, spare parts plan (PDF) About the machine: Offered is a Weiler Praktikum 160 B guide and feed spindle lathe with toolmaker precision in a completely geometrically overhauled condition. Reconditioned with acceptance certificate for tolerances of a new machine. For safety: Electronic spindle protection of the work spindle, cover of the lead and feed spindle, 2 emergency stops and a brake motor. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler center lathe Model Condor 81 guidance and feed spindle lathe with 3-axis digital display from K&C, NEW Geometrically overhauled with inspection protocol for new machine tolerances Technical data: >> Machine No. 84-121 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: metric, imperial, module, and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Equipment and accessories: >> 3-axis digital display from K&C, new, 12 months manufacturer warranty with operating instructions Functions: switching mm/inch, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 pcs., taper calculation, radius/diameter, quick zeroing, count direction switching >> Collet chuck NEW, collets NEW from 3 to 26mm, increments of 1mm >> 160 mm three-jaw chuck with 2 sets of jaws NEW >> Multifix size B NEW with 3 piece steel holders Dsdpfx Afowrm Dtjpjun >> Bed stop >> Electric chuck guard NEW >> Rear wall >> Operating manual >> Coolant device >> Machine feet About the machine: A Weiler Condor 81 guide and feed spindle lathe in a very good, geometrically overhauled condition is being offered. The guides are newly ground or newly scraped. Inspected according to test protocol. The accessories collets and chuck are new. For safety: The machine has a brake motor, electronic spindle guard and two emergency stops, making it an absolutely as-new lathe. Even at high speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is very user-friendly and allows surfaces as if ground to be produced. Take the opportunity to view this machine on site under power and convince yourself of its condition.

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, Weiler Praktikant 160 B lead and feed screw lathe with 3-axis digital readout K&C NEW Technical data: >> Year of manufacture: 1986, machine number 86-160-348 >> Center height: 160 mm >> Distance between centers: 650 mm >> Spindle speeds: 8 steps; from 96 to 2500 rpm >> Spindle bore: 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: 0.02 to 0.63 mm/rev >> Usable threads: metric, inch, module, and diametral pitch >> Metric thread pitches: 0.25 to 8 mm >> Weight: approx. 680 kg >> Spindle brake switchable Dujdpfxowthbie Afpjn >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital readout from K&C, new, 12 months manufacturer warranty with operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, direction reversal >> Collet clamping device, collets as new from 1 to 29 mm in 1 mm increments >> 160 mm new three-jaw chuck with 2 sets of jaws >> Multifix size A with 3 tool holders >> Electric chuck guard >> Bed stop >> Rear wall >> Machine leveling feet >> Coolant device About the machine: Offered is a Weiler Praktikant 160 B lead and feed screw lathe built to toolroom precision in very good condition. The machine is, of course, fully functional. The Weiler was completely dismantled and newly painted in light grey. All slides move very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and can produce surfaces as if ground. Take the opportunity to inspect the machine under power on site and verify its condition for yourself.

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Emcomat Emco EM20D Lead and Feed Lathe, built in 1995, in excellent condition, CE compliant! Technical specifications: >> Year of manufacture: 1995 >> Center height 200 mm >> Swing over bed 400 mm >> Swing over cross slide 250 mm >> Turning length: 1000 mm >> Spindle speed: 4 speed levels, continuously variable from 35-3000 rpm >> Quill stroke 120 mm >> Tailstock: MT3 >> Spindle bore: 50 mm >> 20 longitudinal feeds 0.045 / 0.787 mm/rev >> 20 cross feeds 0.023 / 0.406 mm/rev >> Space requirements / installation dimensions approx. length 1.900 x depth 0.9 x height 1.3 meters >> Weight approx. 850 kg Accessories and equipment: >> 3-axis position indicator >> 1 piece Three-jaw chuck with 1 set of jaws >> Tool holder with 3 pockets >> Chip return wall >> Coolant system Dujdpfjwag Stox Afpsn >> Bed stop About the machine: Offered is an Emcomat 20D centerline and feed spindle lathe, built in 1995, in lightly used condition. The machine is fully functional. All slides run very smoothly and evenly. The bed guides are in very good condition. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition.

Condition: used, Year of construction: 1989, Technical details: number of spindles: 6 spindle passage: 20 mm Article: cam-controlled multi-spindle automatic lathe Manufacturer: Gildemeister Type: GS20-6 Yob: 1989 six-spindle automatic lathe 8 main spindles for bars up to D=20mm All cross units are equipped with a tool holder (from Gildemeister or IMG Attachments) Dusdpfxex Hggwj Afpon All longitudinal units are equipped, either fixed or rotating (without collets) An independent feed is installed at position 1 A gear set for one speed is installed A gear set for one cycle time is installed The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more information and pictures on mail(at) or *

Condition: used, Year of construction: 1989, Technical details: number of spindles: 6 spindle passage: 20 mm Article: cam-controlled multi-spindle automatic lathe Manufacturer: Gildemeister Type: GS20-6 Yob: 1989 six-spindle automatic lathe 8 main spindles Dsdpex Hgkcjfx Afpjun for bars up to D=20mm All cross units are equipped with a tool holder (from Gildemeister or IMG Attachments) All longitudinal units are equipped, either fixed or rotating (without collets) A gear set for one speed is installed A gear set for one cycle time is installed The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more information and pictures on mail(at) or *

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: LZ280/3, turning diameter over cross slide: 190 mm, spindle bore: 43 mm, turning diameter: 330 mm, turning diameter over bed slide: 330 mm, center height: 165 mm, turning length: 670 mm, quill stroke: 90 mm, quill diameter: 45 mm, spindle speed (max.): 4,000 rpm, spindle speed (min.): 30 rpm, GDW precision lathe LZ 330 V EconomyLine Duodpfsv Dan Djx Afpjn The LZ 330 V EconomyLine is a powerful lead and feed spindle lathe with stepless speed control from 30–4000 rpm. The standard paint finish includes RAL 7035 (light gray) for the housing and RAL 7016 (anthracite gray) for the substructure, splash guard hood and chuck guard. Equipment & accessories: ✅ 3-axis position indicator with 6" color display ✅ Quick-change tool holder Multifix A including 1 turning tool holder ✅ Coolant system & central lubrication ✅ Chip tray, splash guard & spindle brake ✅ LED machine light & collet board K32 ✅ Electromechanical limit switch device for thread/feed ✅ Tool cabinet with telescopic extension including operating tools Additional equipment package (optional): ➕ Three-jaw chuck Ø 160 mm (up to 4,600 rpm) ➕ Keyless drill chuck (3-16 mm, B16/MK3) ➕ Live center MK3 & drill bit holder ➕ 4 additional turning tool holders & 1 drill bit holder 📦 Delivery: ✔️ Disposable packaging & safe transport including insurance Perfect for precise and demanding turning operations in industry and trade! 🚀

Condition: ready for operation (used), functionality: fully functional, Machine has drilling / threading unit fitted on It is included barfeeder. Dsdpfexz R Iljx Afpsun

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, turning diameter over cross slide: 1,800 mm, turning diameter: 2,000 mm, turning length: 8,000 mm, total length: 12,000 mm, overall weight: 29,500 kg, Machine can be inspected under power Duedowv S D Hopfx Afpon

Condition: used, Year of construction: 1999, Technical details: number of spindles: 6 spindle passage: 20 mm Article: cam-controlled multi-spindle automatic lathe Manufacturer: Schütte Type: SF20 S Dnt Yob: 1999 Six-spindle automatic lathe with 6 main spindles max. nominal diameter: D=20mm Spindle drum hirth coupled, CNC cross slide in positions 4, CNC cross slide in positions 5, pick up in position 6, sorting chute, 1x independent feed, thread cutting couplings, workpiece belt, Coolant tank with hinged belt chip conveyor Ruez, Oil/steel operation, PLC Siemens S7, Siemens CNC control, Siemens Simodrive 611, The scope of delivery regarding the tooling equipment could be different like pictures. Dsdpfex Sx Nhex Afpjun Interface for: IEMCA PRA bar loading magazine (optional: IEMCA PRA40/31/ built in 1997 rear loader) *

Condition: good (used), Year of construction: 1992, 1 used lead and feed screw lathe Manufacturer: Weiler Model: Condor B Year of manufacture: 1992 Technical specifications: Distance between centers: 750 mm Center height: 165 mm Spindle bore: 40 mm Spindle speed: 22 – 2800 rpm Tailstock: MK 3 Drive power: 1.6 / 3.2 kW Weight: 1040 kg Dimensions: 1,850 x 880 x 1,290 mm Dodpfx Afjw Rcd Sepeun Equipped with: 3-axis digital readout 3-jaw chuck Chuck guard

Condition: good (used), 1 used lead and feed screw lathe Make: Weiler Model: Condor VS 2 Technical Data: Centre height: 160 mm Centre distance: 800 mm Spindle bore: 40 mm Bed width: 240 mm Speeds: 12 - 2800 rpm Drive power: 3 kW Tailstock taper: MK 3 Quill stroke: 110 mm Dsdpfx Afow Rcrcjpoun Feeds: 0.037 - 1.253 mm/rev Weight, approx.: 800 kg Dimensions (W x D x H), approx.: 1930 x 880 x 1470 mm Equipment: 3-jaw chuck Quick-change toolholder system Multifix

Condition: excellent (used), Year of construction: 2018, turning diameter over cross slide: 800 mm, spindle bore: 92 mm, turning diameter: 800 mm, turning length: 6,000 mm, total length: 9,000 mm, total width: 1,900 mm, total height: 2,100 mm, spindle speed (max.): 1,400 rpm, spindle speed (min.): 14 rpm, HeidenHain ND-780 with 3 axis Read-outX, Zo, Z  HeidenHain LS388C Scales 2 x CE Chuck covers for 500 & 900 mm SCHUNK 3 chuck Ø 400-102  Bison 4 chuck.... Steady rest Ø 30 - 210 mm Steady rest Ø 210 - 370 mm DBC Turning Length: 6000mm Swing over bed Ø: 800mm Swing over cross slide Ø:520mm Swing in the gap Ø: 870mm Gap length: 320mm Spindle bore: 92mm Spindle power: 15kW Bed width: 550mm Spindle taper: 6Mk Speeds / ranges: 14 - 1400rpm Length: 9000mm Width: 1900mm Djdpfxjvn Svuo Afpsun Height: 2100mm Weight: 7670kg

Condition: good (used), Centre height: 290 mm Swing diameter over bed: 580 mm Centre distance: 3000 mm Weight: 2800 kg Equipped with a ZIMMER DY 75 flat belt grinder, year of manufacture 2010, e.g. for shaft or tube grinding Siegfried Volz Werkzeugmaschinen Djdpoxtu Ersfx Afpsun Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: used, Year of construction: 2006, functionality: fully functional, Equipment: rotational speed infinitely variable, Manufacturer: 600 Lathes Model: Harrison V350 Centre Height: 170 mm Swing over Bed: 350 mm Swing over Cross Slide: 196 mm Swing in Gap: 535 mm Width in front of Face Plate: 165 mm Distance between Centres: 650 mm Spindle Speeds (stepless via potentiometer across 3 ranges, with digital readout): 15 - 340 rpm 45 - 1010 rpm 150 - 3250 rpm Spindle Mount (Camlock): D1-4 Spindle Bore: 54 mm Spindle Motor: 7.5 kW Carriage Guideway Width: 318 mm Dsdpfoxcuulox Afpoun Cross Slide Travel: 250 mm Top Slide Travel: 140 mm Tailstock Quill Travel: 140 mm Tailstock Quill Taper: MT4 Quill Diameter: 63 mm Metric Version Machine Threads: Metric: 0.2 - 14 mm (51) Imperial TPI: 2 - 56 (56) Module: 0.2 - 3.5 (20) Diametral Pitch: 8 - 56 (20) Drive Power: 7.5 kW Equipment: 3-Axis Digital Readout 3-jaw Chuck Röhm D:200 mm 4-jaw Chuck D:160 mm Collet Chuck System Steady Rest 4-position Quick Change Toolpost Live Centre Chuck Guard Additional Chip Shield on Carriage Coolant System Rear Splash Guard Machine Documentation incl. Schematics Dimensions: Floor to Spindle Centre: 1050 mm Overall Length: 1900 mm Overall Width: 1100 mm Overall Height: 1300 mm Weight: 1350 kg The machine can be demonstrated under power on site by arrangement. All details without guarantee. Errors and prior sale reserved.