Used Mc Km 250 for sale (20,568)

Condition: good (used), Year of construction: 1998, Krauss Maffei KM 800-8000 MC injection molding machine Year of manufacture: 1998 Serial number: 8D980U9 Control system: Krauss Maffei MC3F Clamping force: 8000 kN (800 t) Screw diameter: 130 mm L/D ratio: 22:1 Injection volume: 6570 cm³ Injection weight (PS): 5617 g Injection pressure: 1296 bar Maximum cylinder temperature: 375°C Distance between columns (H x V): 1120 x 1000 mm Dimensions of mounting plates: 1600 x 1530 mm Opening stroke: 2000 mm Minimum mold height: 600 mm Maximum daylight opening: 2000 mm Ejector stroke: 250 mm Ejector force: 226 / 95 kN (front / rear) Screw speed: 92 rpm Injection rate: 929 cm³/s Pump motor power: 132 kW Heater power: 70 kW Number of heating zones: 7 Dry cycle (EUROMAP): 700 cycles/h Iisdpfx Aozrwy Aoiyeg Oil tank capacity: 3600 l Supply voltage: 400 V / 50 Hz Machine length: approx. 10,500 mm Machine width: approx. 2650 mm Machine height: approx. 2400 mm

Condition: excellent (used), Year of construction: 2001, Injection moulding machine: Krauss Maffei KM 800-5000 MC Year of manufacture: 2001 Operating hours: 70,000 h Configuration: Machine with robot, safety cage and conveyor belt Availability: Two identical machines available Clamping unit: Clamping force: 8,000 kN Maximum mould opening force: 356 kN Moving platen opening force: 98 kN Moving platen closing force: 92 kN Mould platen dimensions (H x W): 1,610 mm x 1,530 mm Distance between tie bars (H x W): 1,120 mm x 1,000 mm Mould opening stroke: 1,400 mm Minimum mould height: 600 mm Maximum mould opening: 2,000 mm Hydraulic ejector stroke: 250 mm Injection unit: Screw diameter: 90 mm L/D ratio: 23 Iijdpfexqh I Isx Aiyeg Injection pressure: 1,742 bar Injection volume: 2,863 cm³ Shot weight (PS): 2,605 g Dimensions and weight: Machine dimensions (LxWxH): 10.5 x 2.86 x 2.89 m Weight: 43 tonnes

Condition: excellent (used), Year of construction: 2019, Krauss Maffei KM 250-2000 CX Blue Power with Sepro Industrial Robot SR S5-35HL S4 Trans Year of manufacture: 2019 Injection Unit: Screw diameter: 70 mm Shot weight: 980 g Injection pressure: 1877 bar Metering volume: 1077 cm³ Clamping Unit: Clamping force: 250 t Tie bar spacing: 630x630 mm Platen dimensions: 995x1050 mm Ejector: hydraulic Clamping unit: hydraulic Control: MC6 – touchscreen Additional Equipment: Very good technical condition Operating hours: approx. h in automatic mode Euromap 67 Robot interface Air valve with vacuum measurement x 1 Air valve x 1 Hydraulic core pull x 3 Pneumatic core pull x 1 Hot runner control x 16 Hardened injection unit – bimetallic Energy-efficient machine – equipped with a system of 3 variable displacement hydraulic pumps Parallel movements Proportional valve on injection unit – precise injection Additional oil filtration pump Sepro Industrial Robot SR S5-35HL S4 Trans Year of manufacture: 2015 5-axis robot: 4 axes driven by servomotors (electric): X, Y, Z, B; C axis Touch screen control panel Robot safety package Robot with adapter, conveyor belt, and safety enclosure Purchase of robot and conveyor belt available at an extra charge Iedpfszy In Tox Aiyjig Dimensions: Weight: 20,100 kg Length/Width/Height: 6.50x2.20x2.30 m All machines offered are started up by our service technicians before sale. A video of the technical tests of the selected machine can be provided or it is possible to participate in live technical tests at our facility in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2001, Krauss Maffei KM 800-5000 MC injection moulding machine Year of manufacture: 2001 Equipment: robot Technical details: Clamping force: 8,000 kN Maximum mould opening force: 356 kN Moving platen feed force (opening): 98 kN Moving platen force (closing): 92 kN Platen size (W × H): 1,610 × 1,530 mm Tie-bar spacing (W × H): 1,120 × 1,000 mm Mould opening stroke: 1,400 mm Minimum mould height: 600 mm Maximum daylight: 2,000 mm Iiedpfozd Ta Nex Aiyeg Hydraulic ejector stroke: 250 mm Screw diameter: 90 mm L/D ratio: 23 Injection pressure: 1,742 bar Injection volume: 2,863 cm³ Shot weight (PS): 2,605 g General machine data Dimensions (L × W × H): 10,500 × 2,860 × 2,890 mm Weight: 43,000 kg

Condition: excellent (used), Year of construction: 2010, operating hours: 54,872 h, functionality: fully functional, clamping force: 2,500 kN, screw diameter: 55 mm, displacement volume: 570 cm³, total length: 6,500 mm, total width: 2,200 mm, total height: 2,300 mm, overall weight: 15,000 kg, Equipment: documentation/manual, KRAUSS MAFFEI KM 250-1400 CX Isdpoz A Uhiefx Aiysig Stock No.: 503243 Manufacturer: KRAUSS MAFFEI Type: KM 250-1400 CX Control System: MC5 Year of Manufacture: 2010 Operating Hours: 54872 h Technical Data – Clamping Unit Clamping Force: 2500 kN Tie Bar Spacing (horizontal x vertical): 630 x 630 mm Platen Size (horizontal x vertical): 995 x 1050 mm Minimum Mold Thickness: 330 mm Maximum Mold Thickness: 1150 mm Opening Stroke: 820 mm Ejector Stroke: 200 mm Ejector Force: 58 kN Centering of Moving Platen Diameter: 160 mm Centering of Fixed Platen Diameter: 160 mm Tool Weight: 3430 kg Technical Data – Injection Unit Screw Diameter: 55 mm Injection Volume: 570 ccm Injection Pressure: 2387 bar Screw Length: 22 l/d Screw Speed: 260 rpm Plasticizing Rate: 49 g/s PS Number of Heating Zones: 6 Dimensions & Weight Machine Dimensions (LxWxH): 6.5m x 2.2m x 2.3m Total Weight: 15000 kg Equipment 2x Temperature Control Units for Hot Runner System Screen Text in German CEE Socket 16A Pressure Accumulator for Increased Injection Performance + Ejector or Core Pull parallel Hydraulic Core Pull 1x Air Valve 4x Machine with Material Hopper Machine with Water Battery Machine without Handling System Leveling Elements EUROMAP 12 Interface EUROMAP 67 Handling Interface USB Interface Schuko Socket 10A Low-Wear Plasticizing Unit

Year of construction: 2004, condition: good (used), Spritzgiessmaschine bis 5.000 KN Machine type: Krauss Maffei KM 2300-12000 MC Year: 2004 Control: CNC MC4 Working hours: 93.900 h SPECIFICATIONS Closing unit Closing force: 23,000 kN Maximum tool opening force: 1,420 kN Thrust force of the movable plate (opening): 227 kN Clamping force of the movable platen (closing): 203 kN Tool clamping area (H x W): 2,830 mm x 2,400 mm Stand spacing (H x W): 2,000 mm x 1,600 mm Tool opening stroke: 2,600 mm Iiodozi Sfzopfx Aiyog Min. tool height: 1,100 mm Maximum tool height: 1,800 mm Maximum tool spacing: 3,700 mm Hydraulic ejection stroke: 350 mm Ejector force (forward/reverse): 415/115 kN Screw diameter: 135 mm L/D ratio: 23 Injection pressure: 1,389 bar Displacement: 8,588 cc Projectile weight (PS): 7,815 g Injection capacity: 1,019 cc/s Screw speed: 113 rpm Maximum plasticizing capacity: 191 g/s Nozzle pressure: 241 kN Electrical and hydraulic equipment Rated power of the pump motor: 132 kW Installed heating capacity: 997 kW Adjustable cylinder heating zones: 7 Number of drying cycles: 350 per hour Tank capacity: 2,500 L Dimensions and Weight Machine dimensions: 15.15 m x 4.15 m x 3.29 m Total weight of the machine: 143,000 kg Maximum mold weight: 62,000 kg LRX 1000 Robot X-Axis: 2.000 mm Y-Axis: 3.000 mm Z-Axis: 5.000 mm

Condition: like new (used), Year of construction: 2010, operating hours: 65,850 h, functionality: fully functional, machine/vehicle number: 61013689, clamping force: 2,500 kN, screw diameter: 50 mm, clearance between the columns: 630 mm, displacement volume: 432 cm³, injection pressure: 2,304 bar, injection weight: 393 g, Equipment: documentation/manual, As a dealer in injection moulding machines, we are offering the following well-maintained used injection moulding machine We also, of course, purchase well-maintained injection moulding machines manufactured from 2010 onwards We have been wholesalers of used injection moulding machines for over 25 years In light of recent developments – tax information and benefits for used machinery From 1 July 2025, used machinery will also be eligible for a special annual depreciation allowance of 30% for tax purposes. In addition to the lower price compared to a new machine, you can claim the same depreciation amounts as for a new machine Keyword: Growth booster (Section 7(2) EStG-E) Iodpfx Aisxqhuuoyjig Currently in stock and tested at our Hanover warehouse Manufacturer: Krauss Maffei Model: KM 250 1000 CX Control unit: MC5 Year of manufacture: 2010 Operating hours: 65,850 h Machine number: 61013689 Processed material: PE and PP – thermoplastics Extras - 2 x core pull (movable WAP, fixed WAP) - Pneumatic valve 1 on FWAP - Pressure accumulator for increased injection capacity - Fast SK removal CX Midrange - Ejection of cooled nozzle plug - Start handling during mould movement - Start-up sequence - Cycle time analysis - External USB keyboard - Graphical analysis – maintenance instructions - Electronic coding of injection unit - Pneumatic valve on BWAP blow-out - 12 temperature control points - Potential-free contact BDE - Process monitoring - Cycle storage - Trend graph - Target/Actual graph - PV control - Active back pressure control - From first owner - Origin: Germany Regular maintenance carried out by the manufacturer and previous owner Clamping unit Clamping force: 2500 kN / 250 tonnes. Column spacing: 630 x 630 mm Platen dimensions: 995 x 1050 mm Opening width: 820 mm Mould height: 330 mm min. Opening width max. 1150 mm Ejector stroke: 200 mm Ejector force: 57 kN max/26.3 kg Injection unit Screw diameter: 50 mm Injection volume: 432 cc Shot weight: 393 g/PS Injection pressure: 2304 bar Electrical Pump: 45 kW Heating: 5 zones, 18.7 kW Weight: 13,900 kg. Dimensions: 5.7 x 2.3 x 2.3 m. Complete documentation, manual and software Available immediately from our warehouse in Hanover, Germany, or free delivery subject to reimbursement of freight costs The machine is offered with a functional test certificate The machine is our sole property The machine in question is available immediately from our warehouse in Hanover, is offered in a functionally tested condition and can be viewed whilst powered up. Information about the machines we offer and our company - We only sell machines purchased from current production from our warehouse in Hanover - All machines on offer are inspected and tested prior to dismantling - We do NOT sell goods from insolvency estates - We are NOT a broker dealing in third-party property. - All machines on offer come from successful companies for whom maintenance and upkeep are a matter of course - All machines on offer can be viewed at our warehouse

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036936, clamping force: 800 kN, screw diameter: 35 mm, displacement volume: 135 cm³, injection pressure: 1,837 bar, injection weight: 123 g, mold height (min.): 150 mm, ejector force: 22,000 N, ejector stroke: 100 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 4,750 mm, total width: 1,670 mm, total height: 1,820 mm, overall weight: 5,900 kg, heating capacity: 8.9 kW (12.10 HP), drive type: Vollelektrisch, clear span: 470 mm, tool weight: 6,00,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 80 / 250 PA G01 (order 38670013) (machine no.: 61036936, new, year of manufacture 2023) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 120  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 610 x 560  Tool installation height min. - max. mm 150 - 400  Opening width mm 750  Mold opening stroke max. mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 22 / 22  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 600 SPRING UNIT  Screw diameter / type mm 35 / standard  Effective Ls/D ratio 20.0  Injection pressure bar 1837  Stroke volume cm³ 135  Shot weight at max. stroke for PS g 123  Injection speed mm/s 200  Injection flow rate cm³/s 192  Screw drive/speed 1/min 382  Plasticizing flow (standard screw)4) g/s 19.5  Nozzle contact force kN 30 ELECTRICAL PARAMETERS  Connected load kW 17.8  Installed heat output kW 8.9  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 5.9  Length x width x height m 4.75 x 1.67 x 1.82 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface cascade 4-fold  Electrical preparation for hydraulic auxiliary unit  Euromap interfaces handling E18, E63 Iedjuggb Dspfx Aiyoig  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Automatic central lubrication  Adaptive Process Control (APC)  Spray embossing circuit  Graphic analysis package  Swivel device Injection unit The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: good (used), Year of construction: 2020, operating hours: 2,640 h, functionality: fully functional, power: 75 kW (101.97 HP), fuel type: diesel, driver cabin: day cab, gearing type: hydrostat, emission class: euro6, Equipment: air conditioning, hydraulics, soot filter, KÄRCHER MC-250 Vacuum Sweeper Technical Data: Drive type: Diesel Drive: Two-wheel drive Engine manufacturer: VM Engine power (kW): 75 Emission standard: Euro 6e Travel speed (km/h): 60 Working width with 2 side brushes (mm): 2,625 Maximum working width with 3 side brushes (mm): 2,710 Hopper capacity (l): 2,500 Fresh water tank (l): 200 Optional fresh water tank (l): 390 Permitted total weight (kg): 6,000 Dimensions (L × W × H) (mm): 4,491 x 1,300 x 1,999 Particle filter Comfort seat Heating and air conditioning Heating Hopper: 2,500 l Radio system Rotating warning beacon Water tank: 120, 400 l Year-round use This KÄRCHER MC250 was built in 2020, has only 2,640 total operating hours and 1,820 sweeping hours according to the counter, and is in good overall condition with typical signs of use and wear, immediately ready for operation. Comparable new price: €200,000! - Gross price: €59,900 // Net price: €50,336 Iedpfx Aowzwakeiyjig - Viewing / test drive possible by arrangement - Nationwide shipping can be organized. Shipping costs depend on distance! - Attractive leasing/financing offers available through our leasing partner—contact us for details!

Condition: used, Year of construction: 1999, Injection moulding machine Krauss-Maffei 800 /5700MC, year 1999, for sale. Technical specifications available on request. Iisdpfx Aieyg Hbgeyeg

Year of construction: 2002, condition: ready for operation (used), Clamping force: 2500kN, clear tie bar distance: 630mm/630mm, opening stroke: 1150mm, min. mold installation height: 330mm, screw diameter: 60mm, specific injection pressure: 2000bar, max. stroke volume: 670cm³, connected load: 74kW, control: MC4. Machine dimensions: 5700mm/2200mm/2300mm, machine weight: 12.5t, operating hours: 47,572h. Available from February 2025, including special accessories, Krauss Maffei LRX-S 100, 8x hot runner control points, 4x core pull, blow-out unit, pressure accumulator, hydraulic tie-bar pulling device, energy-saving circuit, ALS interface, 20mA interface and color dosing device interface. On-site inspection is possible, documentation available. Iiedpfxsuiykds Aiyeg

Condition: like new (used), Year of construction: 1991, functionality: fully functional, power: 30 kW (40.79 HP), input voltage: 200 V, type of input current: three-phase, pressing force: 250 t, table width: 760 mm, table length: 2,700 mm, overall weight: 35,000 kg, punching force: 250 t, Equipment: documentation/manual, safety light barrier, AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(!!), 30kW - Japanese standard Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Iodou Dxb Tjpfx Aiyjig Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.

Condition: good (used), Year of construction: 2004, operating hours: 76,000 h, functionality: fully functional, clamping force: 4,200 kN, screw diameter: 70 mm, displacement volume: 1,047 cm³, plate length: 1,200 mm, plate height: 1,270 mm, total length: 9,830 mm, total width: 2,330 mm, total height: 2,480 mm, overall weight: 23,090 kg, KRAUSS MAFFEI KM 420-1900/55 CZ Multinject Stock No.: 503534 Manufacturer: KRAUSS MAFFEI Type: KM 420-1900 55 CZ Control System: MC 4 Year of Manufacture: 2004 Operating Hours: 76,000 h Technical Data – Clamping Unit Clamping Force: 4200 kN Tie Bar Spacing h x v: 800 x 800 mm Platen Size h x v: 1270 x 1200 mm Minimum Mold Height: 380 mm Maximum Mold Height: 1400 mm Opening Stroke: 1020 mm Ejector Stroke: 250 mm Ejector Force: 95 kN Centering of Moving Platen D: 200 mm Centering of Fixed Platen D: 200 mm Tool Weight: 6700 kg Technical Data – Injection Unit Screw Diameter: 70 mm Injection Volume: 1047 ccm Injection Pressure: 1778 bar Iedez Dgc Iepfx Aiyoig Screw Length: 20 l/d Screw Speed: 527 rpm Plasticizing Rate: 95 g/s PS Free Injection Rate: 953 g/s PS Number of Heating Zones: 6 Dimensions & Weight Machine Dimensions L x W x H: 9.83 m x 2.33 m x 2.48 m Total Weight: 23090 kg Equipment Screen Text in German Hydraulic Core Pull 6x Machine without Handling System Machine without Material Hopper Leveling Elements Tool Heating 16x Two-Component Injection Molding Machine

Year of construction: 1991, condition: excellent (used), functionality: fully functional, overall weight: 520 kg, Pump was operated on a test bench and has only run for very few operating hours. Flow rate: 400 m³/h ( 111 liters / second ) Delivery head / delivery pressure: 19 meters / 1.9 bar Pump speed: 1450 1/min NPSH required: 3.83 m Efficiency: 85.7% Shaft power: 24.04 kW Impeller diameter: reduced 264.5 mm (maximum Ø 269 mm) Iiedpfxsrfdtto Aiysg Shaft seal: single mechanical seal Manufacturer: Burgmann Impeller type: closed radial impeller Bearing type: roller bearing Lubrication type: Grease Materials of construction Pump casing: 1.4408 (AISI 316) Wear plate: 1.4408 (AISI 316) Pressure cover: 1.4408 (AISI 316) Shaft: 1.4462 Impeller: 1.4408 (AISI 316) Bearing bracket: Cast iron EN-GJL-250 Shaft sleeve: CrNiMo steel Nominal size of suction nozzle: DN 200 Discharge connection Nominal diameter: DN 150 Nominal pressure suction PN 16 Nominal pressure pressure PN 16 Coupling manufacturer: Flender Coupling type: Eupex NH with intermediate sleeve Base plate: Painted gray cast iron Motor manufacturer: VEM Type: KPER 200 L4 Efficiency class: IE 0 Motor speed: 1435 1/min Frequency: 50 Hz Rated voltage: 380 / 660 V Rated motor power: P2: 30 kW Thermal class: F Motor protection class: IP54 Cosphi: 0.82 Dimensions: Length: 1600 mm Width: 650 mm Height: 820 mm Weight: 520 kg

Condition: ready for operation (used), Year of construction: 2001, operating hours: 70,000 h, functionality: fully functional, clamping force: 8,000 kN, screw diameter: 90 mm, clearance between the columns: 1,000 mm, injection pressure: 1,742 bar, opening stroke: 2,000 mm, TECHNICAL DETAILS Clamping force: 8,000 kN Maximum mold opening force: 356 kN Feed force of the moving opening platen: 98 kN Force of the moving closing platen: 92 kN Platen size (H x W): 1,610 mm x 1,530 mm Tie bar spacing (H x W): 1,120 mm x 1,000 mm Mold opening stroke: 1,400 mm Minimum mold height: 600 mm Maximum opening: 2,000 mm Hydraulic ejector stroke: 250 mm Ijdpoxup Nnofx Aiyeig Screw diameter: 90 mm L/D ratio: 23 Injection pressure: 1,742 bar Injection volume: 2,863 cm³ Shot weight (PS): 2,605 g MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 10,500 x 2,860 x 2,890 mm Weight: 43,000 kg Operating hours: 70,000 h

Year of construction: 2006, condition: ready for operation (used), Travel X/Y/Z: 800mm/800mm/800mm, feed force X/Y/Z: 15000N/15000N/17500N, feed speed X/Y/Z: 50m/min, max. rotary table speed: 25rpm, spindle diameter: 100mm, tool holder: HSK 100, spindle power S1-100%: 40kW, spindle speed: 6000rpm. Magazine capacity for a maximum tool diameter of 280mm: 23. Max. pallet dimensions X/Y: 630mm/630mm, max. pallets in the system: 6, coolant tank volume: 1500l, 50bar high-pressure pump delivery rate: 22l/min. Machine dimensions X/Y/Z: approx. 6300mm/4900mm/4000mm, weight: approx. 19,300kg, control: Siemens 840D powerline, operating hours: 74,637h. Includes integrated tool monitoring IPM, remote diagnostics via modem, Renishaw MP10 touch probe, RSP 4-position round storage, chip removal, coolant system with Knoll VRF 250 vacuum rotary filter, pallet changing device, 6 pallets, 4 of which are clamping towers with universal clamping bars, approx. 100 HSK 100 tool holders, and Losma filter system. Documentation available. On-site inspection is possible. Expected to be available from the end of January 2025. Iiodpfxouxdhuj Aiyog

Year of construction: 2022, condition: like new (used), functionality: fully functional, WOOKIL MEGACUT MC-2500 Die Cutter MAX. SHEET SIZE: 1800x2600 mm Iodpsy Rulcsfx Aiyeig MAX. CUTTING SIZE: 1700x2500 mm MAX. CUTTING PRESSURE: 550 tons

Condition: used, mileage: 1,001 km, first registration: 01/2018, empty load weight: 300 kg, color: red, driver cabin: other, gearing type: other, Year of construction: 2018, load capacity: 3,000 kg, Equipment: crane, Vehicle location: Bovenden. Shell width: 500mm, opening width: 1390mm, capacity: 250l. Complete with Kinshofer rotator and upper suspension! ACCESSORY DETAILS PROVIDED WITHOUT GUARANTEE; subject to change, prior sale, and errors! Iisdpfoyif Rpox Aiysg

Year of construction: 2008, operating hours: 3,200 h, condition: ready for operation (used), screw diameter: 60 mm, This Krauss Maffei KM 200 CX 1400 MC5 was manufactured in 2008. It features a clamping force of 200 tons, expandable to 300 tons, and a screw diameter of 60 mm. The machine includes a hydraulic ejector, side air valve, robot interface, and a 4-zone mold temperature control system. If you are looking to get high-quality injection molding capabilities, consider the Krauss Maffei KM 200 CX 1400 MC5 machine we have for sale. Contact us for more information. Additional equipment • Hydraulic ejector • Side air valve • Robot interface • 4-zone mold temperature control system Machine Benefits Technical Machine Benefits • Tie bar spacing: 560 x 560 mm Isdpfezw Atlox Aiyjig Extra Information Machine still under power

Condition: good (used), Year of construction: 2008, Dahlih MCV1250B Fanuc series 0i-MC Travel range: X1250mm, Y650mm, Z700mm Table dimensions: 1400x820mm Max. table load: 1500kg Spindle taper: BT40 Tool changer: 24 positions Max. spindle speed: 8000rpm Rapid traverse: X,Y 20000mm/min, Z12000mm/min Weight: 10500kg Includes Dahlih 4th axis (A-axis) Includes accessories, documentation, and parameter lists/backups. Iedpfsztkaxjx Aiyoig

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, clamping force: 8,000 kN, screw diameter: 95 mm, clearance between the columns: 1,120 mm, injection pressure: 1,795 bar, ejector stroke: 250 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping unit Injection force: 8,000 kN Distance between columns (h x v): 1,120 mm x 1,000 mm Maximum mold opening distance: 1,400 mm Minimum/maximum tool installation height: 600 mm / 1,100 mm Opening stroke of the clamping plate: 2,000 mm Ejector stroke: 250 mm Ejector force: 226 kN (rearward: 59 kN) Injection unit Screw diameter: 95 mm L/D ratio: 23 Injection pressure: 1,795 bar Injection volume: 3,367 cm³ Injection size for PS: 3,064 g Injection capacity: 690 cm³/s Nozzle clamping force: 166 kN MACHINE DETAILS Control model: MC4 Connected power of pumps: 90 kW Heating power: 61 kW Dimensions & Weight Machine dimensions (L x W x H): 10.4 m x 2.86 m x 2.39 m Net weight: 45 t Transport dimensions Closing unit - Dimensions (LxWxH) 6000x2740x2390mm / Weight 30t Injection unit Dimensions (LxWxH) 6200x2620x2300mm / Weight 16t Iedpfx Asy Ulhceiyeig

Year of construction: 2002, condition: ready for operation (used), With two machining modules, X-axis: -50 to 725mm, Y-axis: -200 to 300 / -250 to 250mm, rapid traverse X-, Y-, Z-axis: 18/12/30m/min, control: Siemens Sinumerik, temperature range: 5–40°C, power type/frequency: 3 PEN / 50Hz, rated voltage: AC 400V, control voltage: DC 24V, auxiliary voltage: AC 230V, connected load: 102kVA, rated current: 148A, rated current (fast): 148A, fuse (slow): 160A, length: 8000mm, width: 3000mm, height: 4000mm, weight: approx. 17t, operating hours: approx. 80,000h. The machine is fully functional, the ball screw drive (recirculating spindle) of the Z-axis was renewed in 2024 and it has been regularly maintained. Comes with documentation, control cabinet, hydraulic unit, filter elements, and chip conveyor. An on-site inspection is possible. Iodjwbuyzepfx Aiysig

Condition: good (used), Year of construction: 2005, operating hours: 59,000 h, functionality: fully functional, clamping force: 4,200 kN, screw diameter: 60 mm, clearance between the columns: 800 mm, displacement volume: 769 cm³, plate length: 1,200 mm, plate height: 1,270 mm, total length: 6,830 mm, total width: 2,330 mm, total height: 2,480 mm, overall weight: 23,090 kg, Equipment: documentation/manual, KRAUSS MAFFEI KM 420-1900 C2 Stock No.: 503535 Manufacturer: KRAUSS MAFFEI Type: KM 420-1900 C2 Control: MC 4 Year of manufacture: 2005 Operating hours: 59,000 h Technical data, clamping unit side Clamping force: 4200 kN Tie bar distance h x v: 800 x 800 mm Platen size h x v: 1270 x 1200 mm Iiedpoz Dgcbofx Aiyeg Minimum mold height: 580 mm Maximum mold thickness: 1300 mm Opening stroke: 720 mm Ejector stroke: 250 mm Ejector force: 95 kN Centering of moving platen D: 200 mm Centering of fixed platen D: 200 mm Tool weight: 6700 kg Technical data, injection side Screw diameter: 60 mm Injection volume: 769 cc Injection pressure: 2200 bar Screw length: 23 l/d Screw speed: 285 min Plasticizing rate: 70 g/s PS Free injection rate: 700 g/s PS Number of heating zones: 6 Dimensions & Weight Machine dimensions L x W x H: 6.83 m x 2.33 m x 2.48 m Total weight: 23090 kg Equipment Screen text in German Hydraulic core pull, 4x Machine without handling system Machine without material hopper Leveling elements Tool heating, 12x

Condition: excellent (used), Year of construction: 2021, operating hours: 5,646 h, functionality: fully functional, clamping force: 800 kN, screw diameter: 40 mm, clearance between the columns: 420 mm, displacement volume: 201 cm³, plate length: 670 mm, plate height: 670 mm, total length: 4,300 mm, total width: 1,600 mm, total height: 2,000 mm, overall weight: 3,900 kg, Equipment: documentation/manual, KraussMaffei KM 80-380 CX Stock No.: 503703 Manufacturer: KRAUSS MAFFEI Type: KM 80-380 CX Control System: MC6 Year of Manufacture: 2021 Operating Hours: 5646 h Technical Data - Clamping Unit Clamping Force: 800 kN Tie Bar Spacing h x v: 420 x 420 mm Platen Size h x v: 670 x 670 mm Minimum Mold Height: 250 mm Maximum Mold Height: 750 mm Opening Stroke: 500 mm Ejector Stroke: 150 mm Ejector Force: 43 kN Centering of Moving Platen D: 125 mm Centering of Fixed Platen D: 125 mm Technical Data - Injection Unit Screw Diameter: 40 mm Iiodpfez Ayi Usx Aiysg Injection Volume: 201 cc Injection Pressure: 1860 bar Screw Length: 20 l/d Free Injection Flow Rate: 295 g/s Number of Heating Zones: 5 Dimensions & Weight Machine Dimensions L x W x H: 4.3 m x 1.6 m x 2 m Total Weight: 3900 kg Equipment 3 freely programmable inputs and outputs Screen text: German Screen text: Polish CEE socket 16A CEE socket 32A Increased ejector force Hydraulic core pull 1x Air valve 1x Machine with material hopper Machine with water manifold Leveling elements Plasticizing unit, highly wear-resistant and corrosion-resistant BDE interface Interface for color dosing unit USB interface Schuko socket 10A

Condition: good (used), Year of construction: 2004, turning length: 1,345 mm, turning diameter: 420 mm, spindle speed (min.): 3,000 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 1,280 mm, Manufacturer: Mori Seiki Co., Ltd. (Nagoya, Japan) + chuck system Machine model: NL3000MC/1250 Serial number: NL301DJ0070 Year of manufacture: October 2004 Machine weight: 7600 kg Electrical data Voltage: AC 200 V Phases: 3 Frequency: 50 Hz Rated power: 44 kVA Full load current: 127 A Spindle motor current: 200 A Interrupting capacity: 5 kA Electrical diagram number: NL301DJ0070 The machine is a CNC turning center (Mori Seiki NL series) with a nominal electrical power of 44 kVA. CHUCK SYSTEM: Manufacturer: Kitagawa Chuck: B-212A821F Chuck cylinder: S2091 Technical data Permissible pressure (when using external chuck jaws on the standard package): 2.7 MPa Maximum speed: 3000 min⁻¹ CNC turning center of the NL series (Mill Center version) with milling capability (driven tools + C-axis). The data is compiled from original Mori Seiki / DMG MORI catalogs and matches your machine's nameplate (year 2004, weight 7600 kg, 44 kVA, 200 V). Capacity ValueMax. turning diameter420 mmMax. turning length1250–1345 mm Swing over bed995 mm Swing over carriage825 mm Bar capacity90 mm (3.5") Standard chuck12" (Kitagawa B-212A821F) Travels X-axis: 260–280 mm Z-axis: approximately 1280–1370 mm (depending on the exact configuration /1250) Y-axis: option (usually ±60 mm for Y/SY versions) Spindle Max. speed: up to 4000–6000 min⁻¹ (limited to 3000 min⁻¹ with your Kitagawa chuck) Spindle bore diameter: 105 mm (approximately 91 mm with chuck) Spindle mounting: A2-8 Spindle motor power: 22/18.5 kW (30/25 HP) or up to 30 kW (depending on the version) Minimum indexing angle: 0.001° Turret (MC version) Number of stations: 10 or 12 Rotary tools: yes (max. 6000 min⁻¹) Power of rotary tool drive: 5.5 / 5.5 / 3.7 kW Indexing time: approximately 0.2–0.3 s Rapid traverses and drives Rapid traverse X/Z: up to 30 m/min Rapid traverse Y: up to 10 m/min (if equipped) C-axis: up to 300–400 min⁻¹ Isdszm Tkajpfx Aiysig Electrical and other data (from your nameplate) Rated power: 44 kVA Voltage: 200 V AC, 3-phase, 50 Hz Full load current: 127 A Machine weight: 7600 kg Controller: typically MSX-850 / MAPPS