Used Plank for sale (145)

Condition: new, machine/vehicle number: 535119ca408d3bd5a8e74be51, empty load weight: 6 kg, maximum load weight: 11 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side collision protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the middle of the loading area, wooden planks 70 mm for widening to 3,000 mm, Low loader lashing eyes 3 pairs of lashing points each 10 tons integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x according to the rest of the neck area distributed between them, spacing not greater than 1200 mm, 1 x rear slope 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (instead of stake pockets) Hedpfx Aaji Ri N Hjmoh Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white/red rear lane departure lights 2 white position lights at the front 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel arch area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give a commitment for 20 tons GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Approval / plates Country of approval: Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for two-line license plate holder Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB nova gray Drive-on ramps hot-dip galvanized Attentio

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) Hsdei Ri Rvspfx Aamjh 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Hsdpfx Aaoi Riy Ejmjh Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Hjdei Ri I Njpfx Aamoh Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Hedpfx Aji Ri Daoameh Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Hjdoi Ri Ryepfx Aameh Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system Hjdpfx Aoi Ri A Ssamjh 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) Hsdpfx Aoi Ri Dljamsh 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Hedpfoi Ri Ddsx Aamoh Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, Hjdpfei Ri I Eex Aameh then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Hodpfxji Riwfj Aamsh Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, Hedpfx Aaei Ri Izsmjh ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: as good as new (ex-display), 1 roller table 3.0 m long x 0.77 m wide with 7 support rollers, with pneumatic lifting/adjustment chain with worm gear and bellows cylinder, with a timber transfer roller carriage with rubber turntable for 1-man timber feed, with 2 lift-up stop rollers for planks from the band saw that have already been trimmed on one side. Hsdpfxet E Nw Ts Aamjh 1 roller table 3.5 m long x 0.77 m wide with 8 support rollers, with or without transfer roller carriage. Other similar roller tables also available.

Condition: new, maximum load weight: 28,240 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,480 mm, loading space height: 2,820 mm, loading space volume: 91 m³, Equipment: ABS, Stock no. 5559 New vehicle in stock – available immediately! Purchase, rent, or rent with purchase option by arrangement! Side tarpaulin retrofit available at an additional cost! Stas 91 m² moving floor / 10 mm flat floor / TÜV load certificate ---- * Manufacturer: Stas * Model: BIOSTAR – moving floor * First registration: - (New vehicle) * Colour: Chassis galvanized, body RAL 7016 silver grey, tarpaulin SIO 7340 * Volume: approx. 91 m³ (13.50 m long x 2.475 m wide x 2.64 m to 2.82 m high) * Gross weight: 36,000 kg * Unladen weight (as per registration): 7,760 kg * Payload: 28,240 kg * Axles: 3x SAF axles / 1st axle lift / traction assist / disc brakes * Tyres: 385/65 R22.5 new on Speedline Diamond alloy wheels * Wheelbase: 7.85 m * Suspension: ECAS air suspension with raise and lower function * ABS / EBS * Cargo Floor CF 500 SL-C floor with remote control and control panel at rear left * 21 floor planks, 10 mm flat * 12 pairs of recessed lashing rings in floor * Welded aluminium end caps * Residual emptying wall with brushes and stainless steel handles * Service door in front wall Hodpfx Asv Emk Usamjh * Swing doors (50/50) with pneumatic locking * 2x locking rods * Swingable rear door cross member * Hydraulic connections at the front with 3 m hoses and * Additional connection beneath body without hoses * Control platform with steps at front left * Fifth wheel height: 1,150 mm * Single wheel fenders * Full-load support legs * One-piece, foldable aluminium rear light guard * Roll tarpaulin (900g/m²) with tension belts * Foldable steel hoops and longitudinal tension belts * 1x toolbox at rear left * 1x aluminium ladder, 3.80 m long * Load pressure gauge * Smartboard * TPMS tire pressure monitoring * Aluminium rear impact guard * 1x extendable ladder at rear right * 2x LED work lights in front of the axles * 2x LED reversing lights at rear * 1x LED work light on interior front wall * 2 x 3-function lamps on upper rear door cross member New vehicle in stock – available immediately! Purchase, rent, or rent with purchase option by arrangement! Notice regarding possible inaccuracies in the listing: Although this listing has been carefully prepared, errors or inaccuracies in the information may occur. No liability is accepted for errors, changes, or prior sale. All information is non-binding. Please contact us to verify details or clarify any questions.

Condition: used, maximum load weight: 27,500 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/2023, next inspection (TÜV): 06/2025, loading space volume: 100 m³, Year of construction: 2023, Equipment: ABS, bioSTAR approx. 100 cbm, 14.9 m internal length Hedpfexplxzex Aameh silver grey BIOSTAR - STEERABLE AXLE - V14900 - VERTICAL FRONT WALL - VERTICAL REAR DOOR Internal body length: approx. 14,900 mm Internal body width: 2,475 mm Body volume: approx. 90 cbm Gross vehicle weight (GVW): 36 t Axle spacing: 1,310 mm Unladen weight: 8,500 kg King pin height: 1,150 mm TECHNICAL DESCRIPTION 1. CHASSIS KING PIN HEIGHT: Precise king pin height is 1,150 mm. AXLES Tridem: Manufacturer: SAF - CUSTOM DESIGN (CD) Capacity: 3 x 9 t Suspension: Original SAF air suspension Brakes: Large disc Wheel offset: ET 120 Brake wear indicators (BVA) included The first axle is a self-lifting axle controlled via the EBS-E system. The third axle is a trailing steering axle. CONNECTIONS BRAKE WEAR INDICATOR (BVA): Brake wear indicators are connected. LIFT AXLE FUNCTION: Without lift axle. Including traction aid. TRACTION AID: The traction aid is activated by pressing a button in the truck (button in truck not included). AIR SUSPENSION: Lifting and lowering function. Aluminum air tanks. STEERABLE TRAILING AXLE LOCKING: Locking of the steerable trailing axle is managed as follows: - via reverse lights - by button in truck (button in truck not included) TYRES: 6 x 385/65 R 22.5 tyres for regional haulage (manufacturer's choice) on ALCOA MATT aluminum rims, ET 120. BRAKING SYSTEM - EBS: EBS-E system WABCO 2S/2M - PREMIUM MODULATOR Dual-line compressed air braking system in accordance with CE guidelines. Spring-loaded parking brake operating on 2 axles. With SMARTBOARD. R.S.S. (Roll Stability System) LIGHTING - ASPÖCK: 24 Volt electrical equipment. 2 x 7-pin + 1 x 15-pin ISO sockets. Aspöck kit. Orange LED lighting mounted on the trailer side. Without junction box at rear - NORDIC. REAR LIGHTING IN UNDER-RUN PROTECTION: Lighting is installed in the fixed aluminum underrun protection. With foldable aluminum lighting cover. 2 x 1 five-chamber lamp - EUROPOINT III - LED version. HYDRAULICS POSITION: Connection at the front wall. With additional connection option below the body in front of support legs. ACCESSORIES EXTENDIBLE LADDER AT REAR: Extendible ladder integrated at rear of vehicle, right side. PNEUMATIC CENTRAL LOCKING: With pneumatic central locking. TOOLBOX: PVC toolbox with key (800 x 460 x 430 mm) SPARE WHEEL HOLDER: Single aluminum spare wheel holder. 2. BODY FRONT WALL: The front wall is made of heavy-duty aluminum plank profiles. INTERNAL SEALING BETWEEN FLOOR AND FRONT WALL: Fixed sealing between floor and front wall using aluminum profile and PVC gasket. SIDE WALLS: Inner and outer surfaces smooth. Double-walled side wall profiles, 600 mm wide - 30 mm thick - 3 mm inside - 2 mm outside (grain specification). Side wall profiles are fully welded on the inside. WEAR PLATE: Aluminum wear plate, rectangular, inside rear, 2000 (L) x 1500 (H) x 4 mm. MOVING FLOOR SYSTEM: CARGO FLOOR CF 500 SL-C, electric control. 21-board floor system. Drive unit consists of 3 double-acting hydraulic cylinders with 200 mm stroke. Rear end plate in stainless steel. FLOOR SYSTEM OPERATION: Electric control with radio remote (genuine Cargo Floor). Loading - stop - unloading via switch. Manual emergency operation using unique red Cargo rotary knob. MOVING FLOOR FRAME: Frame for wheelbase 7,850 mm. 21 floor boards. FLOOR BOARDS: 21 aluminum floor boards - 8 mm ribbed, with welded aluminum end caps. REAR DOOR: 2 portal h

Condition: used, mileage: 1,200 km, power: 110 kW (149.56 HP), first registration: 05/2025, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 05/2027, color: white, gearing type: mechanical, emission class: euro6, number of seats: 2, total length: 6,250 mm, total width: 2,000 mm, total height: 3,150 mm, Year of construction: 2025, Equipment: ABS, air conditioning, central locking, crane, electronic stability program (ESP), soot filter, tail-lift, 0567. GW25N336771, Furniture lift Böcker Agilo 27/1-6 LH, guide rail package, auxiliary drive, furniture slider, telescopic headrest wheels, Maxi furniture platform, enclosed loading area, electric controls, additional installation of extendable front supports, facade protection plank, hydraulic latch lock, reversing camera, turn assist, active brake assist, reinforced front axle, radio, air conditioning, lane departure warning, intelligent speed assistant, toolbox. Subject to errors and prior sale. Hedpextvzzofx Aamjh

Year of construction: 2011, condition: excellent (used), TIMA VOLLALU universal transporter with tilting loading area Hjdpshwmr Hjfx Aameh Type: GTAHK 360/188/3.5 Internal dimensions: 3500x1880x300mm Total weight: 3500kg Payload: 2800kg Own weight: 700kg Tyres: 155/70 R12C Year of construction: 2011 Certificate valid until 07/2022 VOLLALU - trailer with tipping loading area Frame welded in hollow profile construction Aluminum plank floor Double-acting hydraulic cylinder for tilting function spare wheel mounted 8 pcs. lashing eyes

Condition: used, maximum load weight: 42,400 kg, overall weight: 64,000 kg, axle configuration: > 3 axles, first registration: 01/2011, Equipment: ABS, Goldhofer STZ-VLS4-37/80 and Goldhofer Dolly SX 1-25/80 - Height-adjustable low bed with removable gooseneck ----* Manufacturer: Goldhofer * Type: STZ-VLS4-37/80 * First registered: 01/2011 * Color: yellow * Total weight: 64,000 kg * Empty weight according to vehicle registration document: 21,600 kg * Axles: 4x BPW axles, of which 1st axle is steered via turntable steering, the remaining 3x axles are hydromechanical forced steering * Steering knuckle axles up to max. 45 degrees * Tires: 235/75 R17.5 approx. 70% * Suspension: Air suspension with lifting and lowering * EBS Wabco * Removable gooseneck with aluminum side walls * Hydraulic cylinders for support on the tractor unit * Toolbox with flap at the front of the gooseneck * Controls and pressure gauge on the left of the gooseneck * Gooseneck designed for freely rotating 1-axle dollies * Low bed for the chassis can be raised and lowered hydraulically * Chassis with excavator trough (starts from the 2nd axle) * Extendable widening of the loading area 440mm (2x 220mm) and 700mm (2x 350mm) * Wooden planks to bridge the gap between the widenings * Air suspension with raising and lowering to min. 825mm to 1,025mm (no driving position) * 2x fixed driving heights: * 1st driving height 925mm +100mm/-100mm * 2nd driving height 885mm +100mm/-100mm * 2 pairs of retractable lashing eyes in the gooseneck floor * 5 pairs of retractable lashing eyes in the low bed floor * 5 pairs of side lashing eyes on the low bed chassis * 4 pairs of stake holes in the low bed floor * 3 pairs of retractable lashing eyes in the chassis floor * 2 pairs of side lashing eyes on the chassis chassis * 2 pairs of stake holes in the chassis floor * 2x lashing eyes in the excavator trough * Rear of the vehicle sloped 10 degrees * 1-part hydraulic ramps (2,850mm x 720mm) and hydraulic supports at the rear * Operation of hydraulic ramps + supports at the rear left * Smartboard at the rear right * Additional LED reversing lights on the gooseneck and at the rear of the low loader * 1st hand Hodpox Suzasfx Aamsh German vehicle!! German papers!! 1st hand!! Goldhofer SX 1-25/80 Dolly ----* Manufacturer: Goldhofer * Type: SX 1-25/80 * First registered: 03/2011 * Color: Yellow * Total weight: 28,000 kg * Empty weight according to vehicle registration document: 2,750 kg * Axles: 1x BPW axle * Tires: 235/75 R17.5 approx. 70% / twin tires * 3" fifth wheel plate * Single fender * Supports * Loading manometer * 1st hand German vehicle!! German papers!!

Condition: used, maximum load weight: 30,350 kg, overall weight: 45,000 kg, axle configuration: 2 axles, first registration: 06/2024, next inspection (TÜV): 06/2026, loading space length: 12,500 mm, loading space width: 2,550 mm, loading space height: 300 mm, total width: 2,550 mm, total height: 300 mm, Year of construction: 2024, Equipment: ABS, DOLL tera 2-axle low-bed semi-trailer Detachable gooseneck and additionally accessible rear bogie First registration: Unladen weight: 14,650 kg Permissible total weight: 45,000 kg Gooseneck length: 3,070 mm Fifth wheel height: 1,200 to 1,280 mm Swing radius: 2,350 mm Low-bed length: 6,800 mm Telescopic extension length: 5,700 mm Rear axle bogie length: 2,700 mm Excavator trough width: 700 mm Excavator trough depth: 550 mm Low-bed loading height: 300 mm Hjdpfxox E Ixls Aameh Loading height above bogie: 955 mm Trailer width: 2,550 mm Hydraulic suspension range: -70 / +530 mm Technical fifth wheel load: 21,000 kg Axle load: 24,000 kg Detachable gooseneck with external main frame Three-layer trailer paintwork incl. zinc spray coating Doll Tronic CAN-bus system Low-bed floor: 45 mm fir wood planking between flatbed frames 24-volt E-hydraulics Trailer functions controlled via DOLL keypad on gooseneck ADDITIONAL STEERING with REMOTE CONTROL EEG electronic straight-line tracking Rear frame fitted with aluminum folding ramps with lifting mechanism, length 2,100 mm, width 600 mm, mechanical width adjustment, load capacity 20,000 kg Load securing in the low-bed: 7 pairs of swivel lashing eyes, lashing force 13,400 daN 5 pairs of stake pockets in the external frame 3 pairs of M36 threaded sockets on the outside for screwing in lashing brackets Chassis: DOLL tera pendle axles with hydraulically suspended BPW axles All axles forced steering with up to 60° steering angle on the last axle All lubrication points are connected to the central lubrication system (ZSA) WABCO trailer EBS with ABS and RSS Aluminum air tank BEKA-MAX central lubrication system on front and rear bogies Overwidth package with foldable platform extensions, 2x 225 mm; warning board package extendable to 3,200 mm width Tyres: 8 x 245/70 R 17.5 RENTING IS THE NEW BUYING, immediately available as full-service rental from us-----

Condition: new, maximum load weight: 29,560 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 10,600 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, loading space volume: 60 m³, Equipment: ABS, Stock no. 5640 Purchase, lease, or lease with a purchase option by arrangement! Approximately 60m³ STAS agricultural moving floor trailer with integrated grain hopper / service door, etc. ---- * Manufacturer: STAS * Model: FARMSTAR - Agricultural Moving Floor * First Registration: - (New vehicle) * Colour: Chassis RAL 9005, Superstructure RAL 7001, Tarp SIO 7500 * Volume: approx. 60m³ (10.60m long x 2.48m wide x 2.30m high) * Axles: 3x SAF axles / 1st axle with lift and traction assistance / disc brakes * Tyres: 385/65 R22.5 with Speedline Diamond aluminium rims * Wheelbase: 6.25m * Suspension: Air suspension with raise/lower functionality * Gross Weight: 36,000 kg * Unladen weight (manufacturer): 6,440 kg Hodpfexl Ntuox Aamjh * Payload: 29,560 kg * ABS / EBS * CARGO FLOOR CF 500 SL-C with radio remote control and control panel rear left * 21-plank floor system, 6mm ribbed * Aluminium end caps, welded * Rear closure plate made of aluminium * Integrated grain hopper * Additional guides under the floor profiles * Residue emptying wall with brushes and stainless steel handles * Bulkhead made from aluminium plank profiles * Service door in the bulkhead * Smooth side walls inside and outside (grain specification), fully welded * Inspection window in the left rear side wall * Swing doors (50/50 split) * 4x locking rods * Swivelling crossbar at door closure * Hydraulic connections at the front with 3m hoses and * Connection option below the superstructure (without hoses) * Pressure 1" female * Return 1" female * Operator platform with access front left and right * Fifth wheel height 1,150mm * Individual mudguards * Full load supports * Rolling tarp (900g/m²) with quick-clamp system * Aluminium roof bows, foldable * Foldable rear aluminium light guard * Aluminium air tanks * 1x toolbox front left * 1x toolbox rear right * Shovel & broom holder left * 1x 2x8-step aluminium access ladder fixed right * 1x extendable ladder at the rear right * Smartboard * TPMS tyre pressure monitoring * LED rear lights – 5-chamber * 2x LED work lights in front of the axles * 2x LED reversing lights at the rear * 1x LED work light inside the bulkhead * 2 x 3-function lamps at the top of the door crossbar Purchase, lease, or lease with a purchase option by arrangement! Notice regarding possible errors in the advertisement: Despite careful preparation of this listing, occasional errors may occur in the text or information provided. We assume no liability for mistakes, changes, or prior sale. All information is subject to change and not guaranteed. Please contact us to verify details or if you have any questions.

Condition: new, Including parabolic suspension / livestock gates / spare wheel / upper ventilation / lower ventilation Technical Specifications: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: Without first registration • TÜV (Roadworthiness) / HU: 2 years from first registration • Internal dimensions (LxWxH): 434 x 178 x 183 cm • External dimensions (LxWxH): 582 x 228 x 234 cm • Load height (floor): 42 cm • Permissible total weight: 3,500 kg • Unladen weight: 1,265 kg • Payload: 2,235 kg • Chassis: Low-loader (wheels beside the body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, bolted V-drawbar • Very robust welded steel frame • Frame fully hot-dip galvanized by immersion • Multiple cross members for high point loads • Floor made of pressure-treated timber planks and covered with 2 mm aluminum checker plate • Aluminum side walls • Split access door on the left in direction of travel • Interior lighting • Solid hot-dip galvanized frame assembly • Heat-reflective roof • Lateral upper roof ventilation apertures • Additional lateral lower ventilation openings • 2 side struts for extra rear stability • Aluminum tailgate with integrated anti-slip steps • Swiveling aluminum livestock gate at rear ramp • KNOTT parabolic axles for maximum ride comfort • Large 16-inch tires for optimal road holding • Spare wheel with mount • Automatic reversing system • KNOTT overrun hitch and parking brake • Lockable coupling head • 13-pin plug with coiled cable • Reversing lights • Large-format safety lighting Hsdpfxex Sxiuj Aamoh • Integrated rear fog light • Spare wheel with holder • Centrally positioned jockey wheel Accessories available upon request: • Internal cross partition • Reversing lights • 100 km/h approval with shock absorbers • And much more New vehicle with warranty and TÜV. - Financing and leasing options available - Nationwide delivery possible - All prices include VAT - Vehicle registration documents can be sent in advance or temporary license plates (Germany) can be provided - Export plates with customs clearance available Descriptions and images are protected by copyright!! Trailer Center BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available from stock! We have been specialized dealers and repair workshop for over 30 years for brands including Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands - Errors, omissions, and prior sale excepted -

Condition: new, Incl. ramp & door combination / waste water tank / parabolic suspension / cattle divider / spare wheel / top ventilation / bottom ventilation Technical Data: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: none • Technical inspection (TÜV / HU): 2 years from first registration • Internal dimensions (LxWxH): 497 x 178 x 214 cm • External dimensions (LxWxH): 647 x 232 x 265 cm • Loading height from ground: 42 cm • Perm. total weight: 3,500 kg • Unladen weight: 1,460 kg • Payload: 2,040 kg • Chassis: Low-loader (wheels beside body) • Tyres: 175/75R16C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, robust bolted V-drawbar • Very stable welded steel frame • Frame fully hot-dip galvanized by immersion • Numerous cross-members for high point load capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium tread plate • Aluminium side panels • Split access door on the left in direction of travel • Interior light Hsdpfx Aox Sxi Usameh • Heavy-duty, hot-dip galvanized frame design • Heat-reflective roof • Ventilation openings at upper sides of roof • Additional lower side ventilation openings • 2 side supports for extra rear stability • Rear tailgate made of aluminium with integrated step strips • Tailgate with flap & door combination (switchable between full ramp and individual barn doors) • Rear swing cattle divider gate on ramp made of aluminium • Waste water tank under cargo area • Waste water collection tray in rear interior area • KNOTT parabolic suspension axles for maximum ride comfort • Large 16" tyres for optimal road holding • Spare wheel with mounting bracket • Automatic reversing system • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large, high-visibility safety lighting • Integrated rear fog light • Spare wheel with mounting bracket • Centrally mounted jockey wheel Optional accessories available - please enquire: • Interior cross partition (visible in photos!) - at extra cost • Reversing light • 100 km/h approval with shock absorber • And much more New vehicle with warranty and TÜV. - Financing or leasing possible - Nationwide delivery possible - All prices incl. VAT - Vehicle documents can be sent in advance or transit plates (Germany) can be provided - Export plates including customs clearance possible Descriptions and images are copyright protected!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available from stock! We have been a specialist dealer & workshop for over 30 years for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many more brands - Subject to error, change and prior sale -

Condition: new, Incl. parabolic suspension / livestock gate / spare wheel / roof ventilation / floor ventilation Technical Data: • Brand: Ifor Williams • Model: TA5 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle Hedjx Sxh Dopfx Aamsh • First registration: None • Inspection (TÜV/MOT): 2 years from first registration • Internal dimensions (LxWxH): 372 x 156 x 120 cm • External dimensions (LxWxH): 519 x 207 x 165 cm • Loading floor height: 42 cm • Permissible total weight: 2,700 kg • Unladen weight: 780 kg • Payload: 1,920 kg • Chassis: Low-loader (wheels beside the body) • Tyres: 165R13C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, bolted V-drawbar • Very robust welded steel frame • Frame fully hot-dip galvanised by immersion • Numerous cross members for high point load capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium chequer plate overlay • Aluminium side panels • Split entry door on the left (in the direction of travel) • Interior light • Heavy-duty, hot-dip galvanised frame • Heat-reflective roof • Roof-mounted side ventilation openings • 2 side reinforcements at the rear for additional stability • Aluminium tailgate with integrated step strips • Swinging livestock gate on aluminium ramp • Parabolic suspension axles by KNOTT for maximum driving comfort • Tyres provide optimum road holding • Spare wheel with mount • Automatic reverse system • KNOTT overrun hitch and parking brake • Lockable hitch head • 13-pin plug with spiral cable • Reversing light • High-visibility safety lighting • Integrated rear fog lamp • Spare wheel with holder • Centrally mounted jockey wheel Optional accessories available on request: • Internal cross partition • Additional reversing light • 100 km/h approval with shock absorbers • and more New vehicle with warranty and TÜV. - Financing or leasing available - Nationwide delivery possible - All prices include VAT - Vehicle registration documents can be sent in advance or export plates (Germany) can be provided - Export plates incl. customs clearance available Descriptions and images are copyrighted!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been specialist dealers and service workshops for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many more brands for over 30 years. - Subject to errors, omissions, and prior sale -

Condition: new, Incl. parabolic suspension / driving gate / spare wheel / ventilation flaps Technical Data: • Brand: Ifor Williams • Model: TA5 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: Without first registration • MOT/General inspection: 2 years from first registration • Internal dimensions (LxWxH): 241 x 156 x 120 cm • External dimensions (LxWxH): 394 x 207 x 165 cm • Loading height (floor): 42 cm • Permissible total weight: 2,700 kg • Unladen weight: 614 kg • Payload: 2,086 kg • Chassis: Low loader (wheels beside the body) • Tyres: 165R13C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, bolted V-drawbar • Highly stable welded steel frame • Frame fully hot-dip galvanized by immersion • Numerous cross-members for high point load-bearing capacity • Floor made of pressure-treated wooden planks with 2 mm thick aluminium tread plate • Aluminium side panels • Split entry door on left side (in direction of travel) • Interior lighting • Solid, hot-dip galvanized chassis frame • Heat-reflecting roof • Roof ventilation openings on both sides at the top • 2 side struts for enhanced rear stability • Rear tailgate made of aluminium with integrated step strips • Hinged rear livestock gate on ramp, aluminium • Parabolic axles by KNOTT for maximum ride comfort • Large 13-inch tyres for optimal road holding • Spare wheel with bracket • Reverse automatic system • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large-sized safety lighting • Integrated rear fog lamp • Spare wheel with holder • Centrally positioned jockey wheel Optional accessories available upon request: • Internal cross partition • Reversing light • 100 km/h approval with shock absorbers • And much more New vehicle with warranty and MOT. Hodpfx Aox Sxhwoameh - Financing or leasing available - Nationwide delivery possible - All prices incl. VAT - Vehicle registration document can be sent in advance or temporary number plates (Germany) can be provided - Export registration incl. customs clearance available Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available from stock for immediate delivery! We have been a specialist dealer and service workshop for more than 30 years for Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Ifor Williams / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix and many other brands. - Subject to errors, changes, and prior sale -

Condition: new, Incl. parabolic suspension / partition gate / spare wheel / upper ventilation / lower ventilation Technical Data: • Brand: Ifor Williams • Model: TA5 • Vehicle type: Livestock trailer • Vehicle condition: New vehicle • First registration: without initial registration • TÜV/MOT: 2 years from first registration • Internal dimensions (LxWxH): 311 x 156 x 183 cm • External dimensions (LxWxH): 465 x 207 x 235 cm • Loading height (floor): 42 cm • Permissible total weight: 2,700 kg • Unladen weight: 875 kg • Payload: 1,825 kg • Chassis: low loader (wheels positioned beside the body) • Tyres: 165R13C • Suspension: KNOTT parabolic suspension • Jockey wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, securely bolted V-drawbar • Highly robust welded steel frame • Frame complete hot-dip galvanized by immersion • Multiple cross members for high point load capacity • Floor made from pressure-treated wooden planks with 2 mm thick aluminium chequer plate • Aluminium sides • Divided entry door on the left in direction of travel • Interior light • Heavy-duty, hot-dip galvanized frame construction • Heat-reflecting roof • Ventilation openings at the top sides of the roof • Additional ventilation openings at the lower sides • 2 side struts for extra stability at the rear • Rear aluminium tailgate with integrated step strips • Swivelling aluminium partition gate at the ramp • Parabolic suspension axles from KNOTT for maximum ride comfort • Tyres for optimal road holding • Spare wheel with bracket • Automatic reverse function • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large, high-visibility safety lighting • Integrated rear fog lamp • Spare wheel with bracket • Centrally mounted jockey wheel Optional accessories - contact us for enquiries: • Interior cross partition • Reversing light • 100 km/h approval with shock absorbers • and much more New vehicle with warranty and TÜV. - Financing or leasing available Hsdpfx Asx Sxh Rsamsh - Nationwide delivery available - All prices include VAT - Vehicle registration documents can be sent in advance or temporary registration plates (Germany) can be provided - Export plates including customs clearance available Descriptions and images are copyright protected!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available from stock! We have been a specialist dealer and repair workshop for over 30 years for brands including Brian James, Blyss, Debon, Humbaur, Hapert, Unsinn, Cheval Liberte, Ifor Williams, Koch, Lorries, Martz, Stedele, TPV, Tohaco, Vezeko, Variant, Vlemmix, and many more. - Subject to errors, omissions, and prior sale -